Arris Tg862g / Ct Change Wifi Mode
Feb 25, 2013
I recently received my Arris modem from comcast and during the installation phase I kept looking for an option to change the wifi mode from b/g/n to n only as all my network adapters connecting via wireless are n types and I want the max speed available from the modem. At no time did the option come up to define. So I finished the set-up and eveyone is connected, albeit at 54 Mpbs.I have accessed the modem via 10.0.0.1 after set-up in search of another option where I can revise the wifi mode. No luck. Comcast gave me the backhand lob over to Arris and Arris followed through with an overhead smash at the net.
View 4 Replies
ADVERTISEMENT
Jun 14, 2011
Do I need to change myArris-TM502G router when changing to a Linksys E4200 Dual-Band modem
View 2 Replies
View Related
Jan 21, 2013
I cannot connect to the WiFi router, an all-in-one modem+router provided by my ISP. Now, I run an Ethernet cord from the router to my computer: the computer works just fine. As of a day ago, though, none of the home's Apple devices will connect to the network, despite reboots, password retypes, and shouting at them. Each device (two phones and an ipad) can identify my network, but they cannot join. Additionally, there is an old laptop that cannot connect anymore.
View 7 Replies
View Related
Aug 17, 2012
I have an ARRIS Docsys3 modem from Comcast which has a built in WiFi router. I also have a DIR-655. The Modem is in my office and I have a 100' Ethernet cable running through my attic to my front room where the dir-655 is located.
I use the DIR for WiFi as well I have it connected to my TV and Xbox.I use the ARRIS Modem for WiFi as well I have it connected to another Xbox and a Desktop computer.I want to have everything on 1 network, Dir-655 uses IP address 192.168.0.1-100 and the ARRIS uses ranges 10.0.0.1-100. I want to be able to connect to the dir-655 and have the IP for that connection join up with the 10.0.0... network so that I will be able to transfer files freely throughout the network.
I want everything on one network. Right now when I connect a laptop to the DIR-655, I can not access the printer that is connected to the Desktop on the ARRIS modem. I have to connect to the ARRIS modems WiFi to then use the printer on the desktop.Likewise, I want to use the media extender on the Xbox connected to the DIR-655 with the Desktop connected the the ARRIS modem, but I can not because of the to different networks.
View 5 Replies
View Related
Apr 25, 2013
Currently have a linksys wrt54gs connected to an Arris TG852G/CT. Currently getting poor speed via WIFI for Comcast Xfinity service. The Arris modem is connected directly to the Linksys Wireless Broadband Router via Ethernet. It lists the linksys broadband router as unknown device and does need utilize the 54 mb/s g standard available on this device. I have updated the firmware to 1.52, reseted the Arris gateway to factory defaults, and reset the linksys to factory defaults as well. The IP address is 192.168.1.1 for the linksys/ 10.0.0.1 for the Arris gateway.How do I improve connectivity between the Arris Gateway and the LinkSys broadband router (model WRT54GS ver 6.0)
View 8 Replies
View Related
Jun 13, 2012
In 12.x I used to go under atm0 and used ' dsl operating-mode' How can I do it under 887VA running 15.2?
View 1 Replies
View Related
Sep 4, 2011
I don't know if this is even possible, but can I change my wireless network card from 802.11b to 802.11g mode?
View 3 Replies
View Related
Dec 28, 2008
I'm trying to change the wireless security mode on my folks' WRT54G to see if I can get the wireless adapter on their new TIVO to talk to the router. It looks like TIVO only does WEP, not WPA. I get into the wireless page of the router and when I try selecting anything but "WPA Personal", the selected choice flips back to "WPA Personal" in less than a second. I've updated the firmware but no change.
View 9 Replies
View Related
Aug 30, 2012
Trying to secure Linksys WRT54G V8 wireless router. Can't change security mode from 'Disabled'!?
I followed this Post from EXPERT: "Connecting two routers wired - the definitive answer"
[url]...
I got the two routers working but the second one (not using it as a router) is not allowing me to change security mode from "disable" to WEP or anything else.The following Post didn't answered this issue: "Can't change wireless Security Mode on my WRT54G V5"
View 8 Replies
View Related
Jul 22, 2012
My WRT54G Router has been reset after severe weather conditions, the wireless in now unsecure. I am trying to change it back to secure mode under wireless / security wireless, but it does not allow me to do so. The security mode remains disabled and does not change to WEP or WPA.
View 2 Replies
View Related
Jan 31, 2012
it says that the cisco sg300-28 managed switch default system mode is Layer 2. but i want to change it to layer 3.
i can't get inside the "Console Interface Main Menu" where the switching from L2 to L3 will be done.
I have done the ff:
1. Upgraded firmware to 1.1.2.0 (latest)
2. Reset the switch to factory defaults.
3. The guide stated that in order to perform telnet to the switch, you need to enable it. So I logged in first in to the web GUI and enable telnet service.
4. I can now start telnet on the switch but I can't see the "Switch main menu".
All I can see are these lines from telnet:
User Name:cisco
Password:******
switchd5928c#
I just want to know how to get into the console interface main menu where these lines should appear so that i can change the system mode:
• System Configuration Menu
• Port Status
• Port Configuration
• System Mode
• Help
• Logout
View 3 Replies
View Related
Jan 9, 2013
We have a 1262 which was loaded with some recovery image for testing. After this, it doesn't get registered to the wireless controller.
we tried moving it back to autonomous mode and then again back to lightweight to have it join the controller. But it doesnt join the controller, debugs on the devices does not show any logs.
View 6 Replies
View Related
Mar 16, 2012
My SF300-24 switch has been working 100% as a backup switch for a client of mine. At my clients premises it was running 3 Vlan's and doing inter VLAN routing. When my client received their original switch back, I obviously brought my SF300-24 back to the workshop, reset it back to Factory defaults and tried to do a fresh installation on it. I can not get it to change from Layer 2 to Layer 3! I installed the latest firmware but still no go.
Everything works a 100% via the console, but when I go to the System Mode menu and try and edit it, it justs sits at layer 2 and will not chage to layer 3!
View 4 Replies
View Related
Dec 25, 2012
This is for a E1000 model router.I recently downloaded Cisco Connect. It wants my router name and password. I don't know the password. How can I find the password or change it? The password might still be the default, but "admin" does not work.
View 3 Replies
View Related
Jun 11, 2013
I have an Aironet 1250 AIR-LAP1252AG-A-K9 I am having issues with, and I am hoping for some direction on how to resolve them. I understand this question has been posted many times many different ways, but i have no luck unfortunately. Here is where I am: I can terminal into the AP, which has been set to factory default, with the username and password and enable password of Cisco. Once I am in the enable mode, I get lost.
Usually there would be an option to go to config. t, and work from there, but this AP does not have that option, Actually if I do a ? at the enable prompt, the commands list only starts with the letter C; but none are config.
I also cannot get into the web interface of the AP. The AP gets a DHCP IP from my DHCP server, (192.1681.128/24) but I cannot get into the web interface using the IP it gets from DHCP. The page never comes up. To add to the confusion, I cannot turn off the CLI event logging, although I enter the command "no debug all". Maybe I am off on what to put in. Nonetheless, it drives me crazy with messages every two seconds as I am trying to type while attempting to figure things out.
Overall, from reading the forums and doing Google searches, I am going on the assumption that the AP is now in lightweight mode, as opposed to autonomous mode, which is where I want it to be. I have tried the method of updating the firmware to the autonomous firmware from Jan 2013 for the AP. I use the TFTP method as I have found here on the forums a few times; I hold the mode button down while applying power to the AP, let the system LED turn red and release the button so the TFTP process can go through, but nothing changes.
I have the AP powered from a gigabit POE switch. The computer I am using for the TFTP is on the same sub net as the AP. I have tried using 10.0.0.6/24 for the computer with the TFTP on it, made sure the view all file extensions option was checked, and renamed the firmware to the .default extension-still nothing updates.
I also noticed that once I hold the mode button down for 20-30 seconds then let it go, the CLI output says the AP it is on the 10.0.0.x sub net, but I cannot ping the computer with the TFTP program on it. If i try to, it get a "Command not supported" message. So I will go on the idea that this is most likely why I cannot do a TFTP update.
About 30 seconds after I release the mode button and the AP boots, it will say it has a 10.0.0.x IP address, then it starts going crazy with messages that it cannot find a DHCP server.
View 3 Replies
View Related
Feb 14, 2013
I am currently setting up a 2800 Series router, and prefer a username/password type authentication rather than a single enable password. To do this, I did:
Router(config)# username <myuser> privilege 15 secret 0 <mypassword>
Router(config)# username2 <myuser> privilege 15 secret 0 <mypassword>
Router(config)# aaa new-model
Router(config)# aaa authentication login default local
This basically does what I want - when I connect to the router through console, it immediately asks me for a username and password. The thing is - as soon as I provide the right credentials, it takes me to USER EXEC mode (the default command mode). Is it possible to change that so that after entering the credentials, I go right into privileged exec mode?
Bonus question: As it is now, I just have no enable password, so when I login with my credentials, I issue "enable" to enter privileged exec mode without it prompting for an additional password. Is it safe to do it this way - having no enable password but requiring a username and password for login?
View 3 Replies
View Related
Oct 14, 2012
I am facing problem with 7600-ES+20G3C card / Any system reset will change the system operating mode
View 2 Replies
View Related
Oct 18, 2012
i want to change my wireless password how to do it?
View 2 Replies
View Related
Jun 10, 2011
I want to know How can I changed old password to new password for my wifi ?? I forgot old password and security?
View 2 Replies
View Related
Feb 5, 2013
How can i change my modem into a wifi router?
View 1 Replies
View Related
Jan 1, 2013
need to change security so tables will work on wi-fi
View 2 Replies
View Related
Mar 24, 2011
I need to know how to change the wifi channel of the connection. connectify can't do it. I guess you have to set it somewhere in the network card settings, but I'm quite a noob when it's about wireless network. googling my problem didn't get me any good result since all the threads about channel setup are about modem/router wifi channel setting, can't find anything about hotspots.
View 7 Replies
View Related
Aug 14, 2011
instructions about how to change wifi security code
View 1 Replies
View Related
May 5, 2012
i am use wifi connection for this which program i have to run?
View 1 Replies
View Related
Oct 22, 2012
In my restaurant, we currently have a password protected wifi network for customers and staff. The load is typically light, so it's worked fine. Now, we're putting in a new cloud-based point of sales system, which effectively means that I need a totally uninterrupted, high quality wireless signal running to the POS terminal (in this case, an iPad). If the terminal is sharing that connection with 15 customers Facebooking on their iPhones, I imagine we'll have some signal issues. I'd rather not install a second network dedicated to the POS terminal. Are there any other possible solutions, i.e. a way to give priority to the terminal over other connections? A way to "split" the existing network so only a portion of it is available to customers?
FYI, current network speed is 20/mbs 2/mbs, and the POS terminal requires a minimum of 7/2 mbs.
View 5 Replies
View Related
Dec 17, 2011
I want change user name or password, some body stealing my connection.
View 2 Replies
View Related
Jul 4, 2011
I am trying to connect an iPod touch to the wifi, but it says I need to enter a password to do so. I have no idea how to view or change it, so I can't connect my iPod to the internet.
View 3 Replies
View Related
Jan 11, 2011
we are charter High speed customers and just recently upgraded are connection speedHowever today my sisters netbook wireless connection stopped working. My DS wifi connection is also dead now In the past the the wireless network name was wifi-****** but now its called wireless and the wep key no longer works
View 5 Replies
View Related
Apr 5, 2012
I have an arris modem from the ISP company and it works good, bat it is NO wireless model. So I have purchased arris WITH the wireless capability myself and ISP refused to support it so my guess that I need somehow to clone their old modem to my new one.
View 4 Replies
View Related
Jul 29, 2011
I have an issue that has been going on for a week. My computer in question is a dell 4500. My internet service went out so I contacted Comcast. the first tech on the phone had told me my router was bad so I got a new one from their office, hooked it up and still had no internet. the last tech replaced the new modem twice and router saying the same thing He could not get my dell4500 to connect (Ethernet port on the back of the pc shows the green light), all my other devices where finally able to connect and go online through LAN and wireless so the modem (Arris wbm760 is good and so is the router (Netgear wgr614 v8). I have a 169.254... in ipconfig. I've release ( which releases) but when I renewed I get "an error occured while renewing interface local area connection : unable to contact your DHCP Server. Req has timed out" this has been the continous error. I tried the steps here How to determine and to recover from Winsock2 corruption in Windows Server 2003, in Windows XP, and in Windows Vista to no avail (both the automatic fix and the manual steps). I also ran a winsocK fix that I found on a post, nothing. So I wiped my computer and installed windows xp which I've done plenty of times before. Installed and updated all drivers, and now I show an Ethernet connection but I still can't get online. packets sent but no packets received, I've retried all above steps and still at the same spot but get same results, ie ipconfig renew gives same error.
View 8 Replies
View Related
Jan 4, 2013
Today I got a new modem brought from Insight my ISP.
Modem: Arris TG862
Router: Cisco Linksys E1200
What happened is I connected to the modem's configuration page and turned off dhcp for all of the options because I wanted my router to do this, but after doing this and saving my settings, I can no longer connect to the internet or the modem no matter what I try. I really don't want to call insight when they just brought the modem.
View 19 Replies
View Related
Mar 19, 2013
Yesterday, My internet kept failing when i was watching youtube videos,so i had to keep toggling the wifi on my laptop. Now ,my network keeps saying no internet access, yet my phone has no issues with the wifi. No, i dont have or use Mcafee. I ran malwarebytes but it didnt find anything. Superantispyware keeps crashing (I dont run both at the same time.)
View 3 Replies
View Related
Dec 3, 2011
I have a Kindle Fire whose wifi is infrastructure mode and my HTC Hero smart phone which is ad-hoc. Can I use a router or bridge to allow these 2 to talk to each other ?
View 12 Replies
View Related
