I used to have a Thomson st-330 USB modem for my ADSL network. When I wanted to change my IP i just disconnected and reconnected a dial up connection that does the job instantly! (a wan miniport + a batch file to disconnect/recoannect with my password and username)Few days ago i bought a new modem/router (TP-LINK TS-W8951NS)Before that all I knew was that if I wanna change the ip address (if I have a router) was a batch file with commands ipconfig /release/renew.I now know that this changes the ip of my PC not the global IP! So how would I change it without restarting the router? (When i change something in my router interface page (PVC1.2.3....etc) my IP changed instantlybut how do I do this without accessing the router, like commands and a batch file etc? I just found out that my global IP changed on its own after like 30-60 min :S why is that! and to do so manually???
I have a 2wire Modem connected to a Cisco Wireless N Router, that is connected to another Cisco Wireless N Router. All was working well. In my absence sbc (AT&T) changed the pass word of the 2wire Modem. The 2wire has stoped communication with the Cisco Wireless N Routers. I connected am Ethernet wire to one of the ports of the 2wire, and connected it to the 2nd Cisco Wireless N Router. The signal gets to the 2nd Cisco Router. However, when I attempt to access the Internet on the CPU connected to the 2 Cisco Router, I get an error Message saying that there is a problem with the Modem and/or Router. On the available Networks selection screen I can see the connections that I want. The selection info shows connected. But when I try to connect, the I can't.
I have cable and am using an sb5101 modem and an wndr3700 v2 router. I have tried changing the router mac address with no luck. Also the ip address is dynamic not static verified by bigpond.how to change my ip address.
I have a new Linksys E2100 that was working well with an old Verizon modem. Then recently that modem gave up the ghost and I was issued another one (Westel Model 6100G). I have no problems with internet connectivity when connecting directly from my harddrive to the Verizon modem. I am also not having trouble connecting to the Linksys routher as I am able to see my wireless connection with no problem. However, when I try to set up the connnection with the E2100 in the loop (yes, it's connected correctly) I no longer have internet access.I tried de-installing and re-installing the Linksys software (thinking maybe there was some new configuration that would be auto-detected with a new set-up), but this didn't work. I suspect that if the problem is with my Linksys router and not with my Verizon modem that there might be something that could be done to reconfigure something manually but I do not know enough about connections and wireless systems to trust myself not to mess something up.
I've been having this problem with my Belkin router since day 1 when i got it.( not new, got from buddy's place) It's Belkin HI Speed Wifi G router, and what's really frustrating is, everytime i connect to it, I need to manually change the DNS address and switch between 126.96.36.199 & 188.8.131.52 in order to get internet access! Sometimes it even cuts off the internet during a session, without me even disconnecting from the wifi network, where I would again need to switch back and forth to the 2 or 4 ending!
I have a problem connecting wifi router(airlive wt-2000r) to my ADSL modem(webstar epc2203ed2.0) using utp patch cable. When my PC is connected straight to the ADSL modem everything works like charm. But when I connect modem with wan port on the router and router with my PC I get no internet access. The network shows as unidentified network and win7 troubleshooter says: Default gateway not available. Connecting them two devices seems pretty simple and I dont think I am doing anything wrong so what could be the problem?
My DSL modem/wireless router wont broadcast the wifi signal i need to know if it is just defective or a setting that can be turned off, It was working just fine and just recently stopped broadcasting, it works just fine for a direct connection. (It is a regular windstream wireless modem/router.
Is it "possible to create a WiFi" or make my desktop using hardware connection, a hotspot? (Without buying a wireless router/modem/card) I mean, is there a tweak or program I can download to configure my desktop running on Windows 7 to create wi-fi? The reason why I'm interested in this it's because, for Bluetooth, it's possible. Just wondering if they have the same nature with WiFi (In terms of configuration and tweaks)^,
I bought myself a new Edimax Modem/router that generates a WiFi network. I installed it successfully but not all of my house is covered well by the network, I even have some 'blank spots', where there's no WiFi at all. What can I do to improve the coverage? I have no problem to buy additional equipment, as long as my entire house would be fully WiFi-covered.
I have been using broadband in my laptop using asus wireless router/modem DSL-N10E for last 2 months but with Ethernet cable plugged in. I have never used its wifi function. I tried today but was unable to connect after entering security passwordWhen look for troubleshoot it says "There might be problem with the drivers for the wireless network connection adapters"
I've got a Livebox router/modem that provides an ethernet connection for our desktop and wifi connections for our smartphones (all-in-one kind of thing) in a SOHO environment. what i'd like to do is access one from the other, that is move files between a smartphone and the desktop without additional wiring or hardware.
I have read many guides about how to forwarding some port in routers, and i did exactly the same as tutorial,after trying many time i just noticed there is something wrong with my router well here the informations.my router model/name UTStarcom AR7RD im using Windows xp SP3 86x my firewall is disable (But i already added the ports i need to open in my firewall)my Upnp are disable in my router well my computer takes a ip from ISP soo i dont need static IP there is no option that let me delete the old useless ports,i searched almost all the sections of my router and i failed to find a thing that let me delete some port.i went to DMZ setting to Active it cuz its the last thing for me to able open some port, i went to DMZ SETTING and tried to enable the check mark for this section i noticed it wont enable, i got no error there just it wont be enable.im watching around its 2 weeks i search any where in different forums and googles.
I've searched high and low across the wide web, but I have found no real answer to this problem;Recently, I bought the DIR-655 because the gods of thunder decided to euthanize my old WAP. The original plan was to mate this up with a Tilgin VOOD-modem (modem and router in one; a heap of s**** in my uneducated eyes) in order to make networking within my appartment somewhat easier.
Got it safely indoors, plugged it in as the manual told me, and got it going (my old WAP was also a D-LINK, so the interface was somewhat familiar). Checked cabled connection, worked fine, and I got the wireless-bit to function as well. But then I, or my Xbox 360 to be right on the money, encountered a little problem. As I understand from a little bit of research, I found out that this was a dreaded phenomenon known as
Before I got the old WAP indoors, I used the onboard router in the TILGIN to do the switching. I used to have this problem back then also, but solved it by opening some of the ports on the modem. Then it switched to "Open NAT", and worked like a charm. Now however, I have ran into a problem I can't dig myself out of. I have tried DMZ, opening numerous ports all the way to the full monty, but I can�t get that NAT to wander into the more acceptable range. And then it became clear that the internet on my laptop was somewhat amputated as well; simple youtube-videos became harder to load (sometimes it actually had to stop for extended streaming!), and this is not acceptable on a 20 mbt DSL-line!
I am having netgear JNR 1010 wifi router and I use Cablenet. the wire which carries internet is directly connected to my Desktop pc's LAN port without modem.Is there any way to install this router without conecting to modem?
My mom wants to buy my dad a Kindle Fire for Christmas. Currently they have a desktop computer with a modem plugged into it and use Verizon dsl for their internet. The Kindle needs wi-fi and I don't want to disrupt the way their computer is set up now.Do I simply plug the router into the modem to get the wi-fi signal?
I have 2 computers running Windows 7. Recently I changed from a Motorola 3347 modem to a Actiontec Q1000 modem. After changing modems I am unable to network the computers, I get error "0x800070035 The Network path was not found".I can plug the old modem in and the networking will work.I have tried to duplicate all of the settings on the Q1000 modem from the Motorola, however there are some different options/settings that do not overlap.
I am trying to get my parents Kindle Fire to work. They recently purchased a Motorola Modem/Router which is hooked into the desktop and works fine. I want to get their new kindle to work and can not seem to figure it out. Their operating system is Vista which I can upgrade to Windows 7 if that would make it easier. When I click on setup the WiFi part of the installation wizard cd that came with the Motorola it says there is not a network adapter. I know what that is however I do not know why I would need it when the desktop is hooked directly into modem/router and I just need the WiFi for Kindle.
I have an ARRIS Docsys3 modem from Comcast which has a built in WiFi router. I also have a DIR-655. The Modem is in my office and I have a 100' Ethernet cable running through my attic to my front room where the dir-655 is located.
I use the DIR for WiFi as well I have it connected to my TV and Xbox.I use the ARRIS Modem for WiFi as well I have it connected to another Xbox and a Desktop computer.I want to have everything on 1 network, Dir-655 uses IP address 192.168.0.1-100 and the ARRIS uses ranges 10.0.0.1-100. I want to be able to connect to the dir-655 and have the IP for that connection join up with the 10.0.0... network so that I will be able to transfer files freely throughout the network.
I want everything on one network. Right now when I connect a laptop to the DIR-655, I can not access the printer that is connected to the Desktop on the ARRIS modem. I have to connect to the ARRIS modems WiFi to then use the printer on the desktop.Likewise, I want to use the media extender on the Xbox connected to the DIR-655 with the Desktop connected the the ARRIS modem, but I can not because of the to different networks.
I have recently changed my Router to a Draytek Vigor 2830N from the standard O2 broadband router. When I swap them out I get no internet access via the main PC that is connected via ethernet. However I can access internet via WLAN on any other device. here are the ipconfig details for before and after swap (same)
I am a Rogers Customer (Canadian isp) whch uses DHCP IP address. My set up is like so: SMCD3GN2 Modem with gateway and wireless mode disabled. (i'm using it as a pure modem) 2 of its 4 ports are active, one is connected to my pc directly and the other is conencted to a d-link router. The router is connected to 4 other pc's + some wireless devices. What I want to do is change my IP address ( the pc with the direct connection ) in windows 7. I can effectively do this by simply shutting the modem off for about 30 seconds. Luckily my isp pretty much continuously assigns me a new IP address every time I do this.
The issue is I don't want to disrupt my entire network ( the router ) With windows XP I used to be able to go into cmd and ipconfig/release, then go to my ipv4 settings and set a custom spam ip address/subnet and then go back to automatic and then ipconfig/renew and voila I would have a new IP address. With windows 7 I have no luck. I have tried spoofing/changing my mac address of my network card/adapter and it results in my modem not assigning me an IP address. Is there any efficient way to change my DHCP IP address in windows 7 without disrupting my entire network?
I have broadband connection on a wired DSL Modem. Now I want to create a wireless networking environment at my home so to work with my laptop and WLAN enabled phone. I do not like to buy a new Wireless router.
Is is possible to deploy my existing modem/router with some extra equipments to build a wifi hotspot?