Thomson St-330 Modem - How To Change Global IP Address Without Restarting Router
Dec 4, 2012
I used to have a Thomson st-330 USB modem for my ADSL network. When I wanted to change my IP i just disconnected and reconnected a dial up connection that does the job instantly! (a wan miniport + a batch file to disconnect/recoannect with my password and username)Few days ago i bought a new modem/router (TP-LINK TS-W8951NS)Before that all I knew was that if I wanna change the ip address (if I have a router) was a batch file with commands ipconfig /release/renew.I now know that this changes the ip of my PC not the global IP! So how would I change it without restarting the router? (When i change something in my router interface page (PVC1.2.3....etc) my IP changed instantlybut how do I do this without accessing the router, like commands and a batch file etc? I just found out that my global IP changed on its own after like 30-60 min :S why is that! and to do so manually???
View 2 Replies
ADVERTISEMENT
Aug 15, 2012
I have Thomson Tg585 v7 router, when trying to add new game application to set the ports for GW2 my router just restart by it self, and i can't add the application even if i do it fast it won't take any name i try for it,even tho i did add ports for BF3 like 2months ago and it worked fine.
View 1 Replies
View Related
Apr 14, 2011
My ISP gave me a Thomson THG520 modem when I subscribed to their service. It has 2 links and USB and an Ethernet link. It worked fine with our 2 computers but for several weeks or so I experiencing that it only gives me IP address only on one interface that one that's first plugged into the computer.
If I reset the modem and plug in the USB I get an IP address immediately. If I unplug the USB and plug in the Ethernet cable I don't get an IP address. If I reset again the modem and plug in the Ethernet cable I get an IP address but not on the USB link after I unplug the modem.
EDIT: after entering the modem's administration I realized it's firmware was updated (probably my ISP did it.). Also I read about how this stuff works, there is an evidence that my ISP set the CPE limit to 1. (so it seem only one computer connected to the modem can get IP address while the other can't.). And this configuration is stored on the modem somewhere. Is there a way to view it somehow?
View 1 Replies
View Related
Jun 13, 2012
I have cable and am using an sb5101 modem and an wndr3700 v2 router. I have tried changing the router mac address with no luck. Also the ip address is dynamic not static verified by bigpond.how to change my ip address.
View 3 Replies
View Related
Feb 16, 2013
A Thomson TG585 v7 (Modem + WiFi Router) receiving a DSL connection and Providing internet access on two interfaces connection :
1- WiFi : to connect portable devices at my home.
2- 4 Ethernet ports : to connect my desktops.
One of these ports on my Thomson is connected to a D-link unmanaged switch to provide extended wired connections. From this unmanaged 4 ports switch one port is connected to my neighbors in another building through UTP, and connected to a D-link DIR 605-L WiFi router, the IP address of the DIR 605-L is 192.168.1.77 and the IP address of my local Thomson is 192.168.1.254 which means they are in the same network. I need to access the DIR 605-L WiFi router from my my home where I am connected directly to Thomson router through UTP cable, I am not able to do that !! , while also I can't even ping the DIR 605-L IP 192.168.1.77.
View 1 Replies
View Related
Oct 3, 2012
I have a Thomson tg782, with a USB port on the side. I want to plug my sub modem internet into that usb port, and then share that connection over wifi, because the router has a wifi function.
View 4 Replies
View Related
Feb 11, 2011
I'm trying to setup a Canyon CN-FW514 wireless router through a Thomson modem.When I first started trying, I could get up the set-up screen on [URL] however this is as far as I got; the laptop said it had a very strong signal with the wireless connection, but I could not get any web pages to open (windows explorer couldn't detect any problems either). The Thomson modem works when I conect it to the laptop via the ethernet cable, but that's not much use to me trying to use the internet elsewhere in the house!I tried changing the IP address, subnet mask and gateway IP address on the set-up screen [URL] which seems to have been a big mistake; I now can't even get the set-up screen to appear.I've reset the internet options and have set everything to obtain the IP address automatically but am still having no luck.
View 5 Replies
View Related
Nov 8, 2011
Five months ago we moved into a new apartment, and connected up our broadband; the ISP provides a Thomson Speedtouch modem (ST546 v6), which I understand from Tech Support is running software v4 (it was issued with V5, but rolled back to V4 for stability issues).We prefer a WiFi network, so purchased a Belkin N Wireless Modem Router (F5D8636-4 v2); I connected it up ditching the ISP issued modem, and all worked well for four months. Suddenly it refused to see the ADSL connection - orange light flashing.So after four nights of 'fault resolution' with Belkin, they decided to send me a replacement... which I finally received last night. It didn't work - same problem, flashing orange light.I have the correct user name and password for the ISP - checked it not once, not twice, but four times. The Thomson Speedtouch works, but doesn't provide a WiFi environment. Can I connect the Belkin modem router into the back of the Thomson and transmitt/carry the WiFi signal that way, and if so, how? I tried (the obvious to me) plug a ethernet cable from the Thomson modem into the Belkin, but nothing.. I'm guessing there are a few important steps I missed.
View 3 Replies
View Related
Jun 6, 2011
So I used to use a Thomson TG585v7 modem router (wireless) as my means of connecting to the internet, the aerial cracked on it and I began getting dropped connections, so I went out and bought a D-Link DSL-2730B modem+router. I am hooked up wirelessly to the internet as there is no phone jack in my bedroom, and I experience massive and prolonged lag while playing call of duty 4 multiplayer, which I never had before with my old Thomson modem. My ping also shoots up to about 400 and then 999 while I teleport around the map.
View 3 Replies
View Related
Aug 13, 2012
I am a Rogers Customer (Canadian isp) whch uses DHCP IP address. My set up is like so: SMCD3GN2 Modem with gateway and wireless mode disabled. (i'm using it as a pure modem) 2 of its 4 ports are active, one is connected to my pc directly and the other is conencted to a d-link router. The router is connected to 4 other pc's + some wireless devices. What I want to do is change my IP address ( the pc with the direct connection ) in windows 7. I can effectively do this by simply shutting the modem off for about 30 seconds. Luckily my isp pretty much continuously assigns me a new IP address every time I do this.
The issue is I don't want to disrupt my entire network ( the router ) With windows XP I used to be able to go into cmd and ipconfig/release, then go to my ipv4 settings and set a custom spam ip address/subnet and then go back to automatic and then ipconfig/renew and voila I would have a new IP address. With windows 7 I have no luck. I have tried spoofing/changing my mac address of my network card/adapter and it results in my modem not assigning me an IP address. Is there any efficient way to change my DHCP IP address in windows 7 without disrupting my entire network?
View 7 Replies
View Related
Apr 9, 2012
How to change ip address on frontier mod.7500 so i can run them together
View 1 Replies
View Related
May 17, 2010
I've got an issue with a CSS 11501 where, if *any* change is made to a global keepalive (active), the device reboots. The code is 08.10.2.05. I'm unable to search the TAC archive or I would've gone there first.
View 2 Replies
View Related
Aug 10, 2011
I'm using a Thomson Technicolor 587nV3. I need to change my NAT status from strict to open. So I can play MW3 online and connect to my friends online games and so I can host multiplayer matches. I have windows 7 laptop to do any of the steps required. I've tried to bind my routers cone through Winscript but without any luck perhaps I done it wrong
View 5 Replies
View Related
Jul 3, 2012
I purchased a computer which has a GA-B75M-D3H motherboard in it.I have been attempting to connect it to the internet with little success. I have a Thomson TG782T modem hooked to the computer by ethernet cable. The computer does not recognise the modem and the modem does not find the gateway on the computer. I have discussed the problem with Telstra and as far as they are concerned its not their problem due to the cable showing green and amber light into the back of the computer and the modem is working. The computer guys are saying that the computer is fine as they utilised the net to load the computer.
View 1 Replies
View Related
May 28, 2010
Life was great with my DIR-615 and Motorola Surf Board SB-5100 cable modem, but my D-Link refuses to recognize the Internet signal from the Thomson. The Comcast guy spent an hour trying to get it to work, but I'm stuck watching MLB.tv on a 24" monitor in a stiff office chair in my study, instead of on a 47" LCD in my living room. How can I force the DIR-615 to accept the Thomson ACG905? If you advise me to check settings or manually change them, please do not "assume" that I know how to access those settings.
View 6 Replies
View Related
Oct 22, 2011
The problem i'm having is that i'm using a 100gb capped internet plan, but after 1-2 weeks it gets all used up. After checking to see who's accessing the internet there's 2 unknown mac addresses who are constantly accessing the internet. Whenever this happens, the internet becomes considerably slower (i'm guessing they're torrenting or downloading off our internet).
I've even tried changing the wpa password but they're somehow still accessing the internet. So i've been looking for a way to ban mac adresses but i can't seem to find the option on the router.
Here's a screenshot:
YES, i know there's an option that says "Allowed on WLAN", but i cannot un-check the box for some stupid reason.
I really don't know what to do! Is there some kind of command i can type in the command prompt or something to ban mac address manually?
View 5 Replies
View Related
Jul 10, 2011
I installed the thomson router, the process was sucessfully completed however the laptop could not automatically renew the IP address and the DNS server address???
View 2 Replies
View Related
Apr 7, 2011
I connect to the internet through a Thomson TG585 v8 modem. When I log in to the modem's IP (192.168.1.254?) through a browser, I only get one task available, that is "Check connectivity for this internet service". As far as I know, I should have some management options, like for example to block websites, to limit internet service for certain devices etc... Does anybody knows why I don't have these options? Could it be a restriction from the Internet Service Provider?
View 2 Replies
View Related
Nov 30, 2012
I am using a Thomson ST516 v6 DSL Modem, through which I have connected a Tenda W311R+ Wireless Router. There's two laptops, one running Windows 7 Sp1, the other running Windows Xp Sp3, and an Android based phone using this connection. I should mention that the problematic laptop had Windows 7 before switching to Xp and ran without any issues.
[code]....
View 12 Replies
View Related
May 6, 2013
I have an ASA5505 with 8.4 software used on a business DSL account.This means I am running PPPoE session to the provider and am then given an Inside Global subnet /29.I have various servers NATed to specific IP's then have the DHCP users NAT with overload to another of my inside global addresses. When I try to establish an IPSEC tunnel to any of my inside globals and monitor I get an access denied message but there is nothing that is blocking.If I determine my PPPoE IP address I am able to extablish a IPSEC session to that but cannot exchange traffic. Not that I want to use that IP anyway because that PPPoE Session IP changes and only my inside globals are static.I spent several hours on this and cannot put my finger on it. Do I need to allow VPN to the INSIDE interface?
View 2 Replies
View Related
Feb 28, 2012
! have a TELSTRA ADSL wireless router ( Thomson TG782T)I need to connect my 2 printers to it so I can operate them wirelessly to my laptop and Desktop computers
Laptop: TOSHIBA Satellite w/- windows 7 Professional
Desktop: ASI Computer w/- Windows 7 Ultimate currently connected to ADSL modem by yellow network cable.
View 1 Replies
View Related
Oct 24, 2012
We're currently PATing everything from a particular subnet to the IP of an outside interface using our ASA5585 (dynamic PAT). We're experiencing pool exhaustion and therefore need to expand the global IP range. Any way of cutting over to the new range without dropping existing connections? For clarity, the current interface address is x.x.x.37/22 and the new PAT pool is x.x.x.114-6/22.
View 6 Replies
View Related
Mar 17, 2011
Got an ASA5520 running V8.2(3) and we want to upgrade our internet bandwidth. Our ISP says OK but we need to install different physical circuit, upgrade CPE router, etc.
Then they say, btw your globally allocated IPs will change - this is a problem as we have Site-to-Site VPN Tunnels, IPSEC RA, etc.
ISP are proposing to give us a 3 month period whereby old & new IP blocks will be routed to our ASA (by means of secondary IP address on their Cisco CPE).
Multiple IPs on the same physical i/f on the ASA require sub-interfaces/IP Addresses/VLAN ids on my "outside" i/f.
Is this going to horiibly break Site-to-Site VPN Tunnesl, IPSEC remote access ?
Will VLANs work at all with IPSEC on the "oustide" i/f at all ?
View 2 Replies
View Related
Nov 30, 2011
I have an ASA 5510 running version 7.0. I have a problem with an exchange server using a static map and its outbounc connectivity. It connects outbound through the global address even though inbound connectivity works fine through the static mapping. The recent changes are changing of the zero route through a different interface (there are to circuit connected to this ASA on different interfaces). So the idea was to get all workstations in the office using the global address and routing out through one circuit, and the servers connecting in/out through the other circuit. Shouldn't a static mapping ignore what the zero route is?
Here are what I believe to be the relevant configs.
interface Ethernet0/0
description New 6mb circuit
speed 100
[Code]....
So exchang2 server can be connected to from the outside properly via IP xxx.207.51.231/exchange2-outside, but all outbound connections from this server are going out via IP xxx.122.47.218/circuit-6mb as do all the workstations due to the global address statement.
View 2 Replies
View Related
Feb 25, 2011
I need to change the ip address on my router same ip address as myDlink router?
View 6 Replies
View Related
Feb 5, 2013
How can i change my modem into a wifi router?
View 1 Replies
View Related
Jan 5, 2013
How do you change channels on a router or modem???
View 2 Replies
View Related
Oct 11, 2011
I have a TP-Link device TL-WR340G Wifi Device. I connect a PC through one of the LAN ports.Mow my WiFi router's MAC address has not been registered at my ISP system. I need to find a way to 'change' my Routers MAC address to another MAC address. The cloning doesn't work. I need to change my Router's LAN MAC address.
View 6 Replies
View Related
Jul 24, 2012
i always get ban i czero due to high ping is there any way i can change my ip address so i can get in server again
View 8 Replies
View Related
Mar 9, 2013
I have bought a new belkin router since my old ITI router had some problems and it died. My ISP used to check my old router's mac address to authorize me to use the internet but since i have changed my router i cant access the net from home anymoreBefore i used to change the mac address of my laptop to be same as that of router to be able to access the net. How to change my new belkin router's mac address to the old ITI router's mac which i have saved in my laptop.
View 13 Replies
View Related
Nov 21, 2011
I need to connect to my work PC remotely through VPN, but the address of my home router (Verizon Fios) conflicts with my work address. IT guy at work is clueless, so I am stuck - been trying with him for months and this is his solution. I need to change my address on my personal router, Westell brand, but I am having no luck. I have been told to use:
ID: admin
password: password
When I tried that, each time I press a key in the password field, it enter 4 characters... I have never seen anything like that. Honestly, I'm a graphic designer and am also clueless on networking issues.
View 2 Replies
View Related
Apr 8, 2011
How come my IP address does not change when i'm using my router.... (TP-link WR340G)But when i connect my DSL directly to my computer it my IP can be changed..... and when i put back my router my IP address is the same.
View 1 Replies
View Related
Aug 4, 2011
I have a Linksys wag200g Modem/router and I need to change my Emails registered password.
View 4 Replies
View Related
