Cisco Wireless :: 2504 Management On VLAN?
May 10, 2012
We are installing a 2504 with management on VLAN2. The management port is on interface 1 which is attached to a layer 3 3750. From other VLANs in the network we cannot manage the 2504 controller with the web manager. We are running the latest code, 7.2.103.0, since we are using 3600 APs. We have a TAC case open, but spent 3 hrs with them and they can't figure out the problem. TAC did some debugging and saw that the 2504 is ARPing for the address of the PC on the other VLAN instead of sending the packet to its default gateway. How to get success with the management interface on a VLAN and managing the controller from another VLAN?
View 2 Replies
ADVERTISEMENT
Feb 29, 2012
It seems like the 4-ports switch in the 2504 can only one port can be used for management VLAN at a time ? I need all 4 ports to be untagged in the managment VLAN.
View 7 Replies
View Related
Sep 25, 2012
is it possible to Manage the 2504 Controller over a separate Interface. Exmaple: Port 1 is used as controller management interface (untagged) - AP's are connected to the same VLAN Port 1 is used for Guest Traffic (VLAN 3 tagged) Port 2 should be used to manage the WLAN Controller from the internal LAN. (tested with untagged, tagged, same issue)
with this Setup it is possible to ping the Port 2 IP-Address from the internal LAN but if you try to connect to the controller, the Browser shows "Site not reachable".
I also enabled "Management via Wireless" but without success. I also tried to add the "management" VLAN as tagged on the management Interface with the same effect, the controller is not manageable from the internal LAN. On 5508 WLAN Controller i have an similar setup, but with LAG Port enabled. There this works.
The only interface were i can manage the WLAN controller is from the management Interface.
View 1 Replies
View Related
Jan 3, 2012
I am tasked with configuring a 2504 wireless controller. Is it possible to assign an SSID to an interface that has dynamic ap management enabled?
Scenario:
Location1:
1) 10.0.0.0/24
2)192.168.0.0/24 DMZ
Location 2:
1) 10.0.5.0
Both locations are routable using network 1 at each location. However, I need to configure several access points and send them to location 2. These access points will communicate with the controller at location 1 on network 1. Two SSIDs will need to be on network 1 at location 1. The other SSID will be on Network 2 at location 1. This network is not routable.
View 32 Replies
View Related
Jul 29, 2012
Is it possible to use a 2504 wifi controller to manage compatible AP's across different subnets ?
View 2 Replies
View Related
Jan 20, 2011
I have a Netgear GSM7248R switch with 5 different Vlans including th management Vlan. Each of the vlans are connected to my layer 3 switch for routing. I want to access the management vlan form any of my Vlans so my layer two switch can be detected by my snmp manager.
View 3 Replies
View Related
Aug 8, 2012
My problem, in a nutshell, is that clients do not get an IP from an external DHCP server when connected to a guest VLAN.
My current setup is:
Native VLAN 1 (192.168.2.x)
2008 DHCP Servers
2504 WLC
[Code].....
The guest WLAN just uses WPA and a PSK and is set to interface vlan101 There rest of the 2504 config is default.
The ports that the WLC and APs are connected to are tagged on the correct VLANs. (is that even necessary for the AP now?)
Ive changed the interface config around a hundred times now with no luck. No matter what a client will not get an IP.
Could this be due to the 2504 and ASA both acting as DHCP relays? Ive tried setting the IP of the DHCP on the dynamic interface to many different things with no luck.
View 10 Replies
View Related
Mar 28, 2012
I created a wlan just for our wireless IP phones.I assigned an interface I created which in turn was set to a specific port on company 2504 WLC. Connecting switchport is set to trunk. Right now I can't ping the voice wlan interface.
View 1 Replies
View Related
Feb 26, 2013
I have a WAP321 I am trying to set up. It's connected to gi1/23 and the switch system mode is set to router. The rest of the network works just fine.I have an SG500-28p and the port. [code] On the WAP321 wizard, configured IP address on my management vlan and also configured the default SSID on that vlan. That works. (I plan to remove that one) Then I add the two SSIDs for vlan 20 and 22 (private and public access) and I can't associate to either of the two additional SSIDs. I haven't configured any other settings beyond the wizard and adding the other two SSIDs. I do want cisco mobile ios (jabber) to work on the private network and also do have a couple spa525g2s that need to connect wireless.
View 1 Replies
View Related
Aug 16, 2012
I am working to configure AP541n AP, is able to connect to the AP wired, assign AP static IP with proper subnet mask & default gateway, when it's done, everything looks perfectly, but since I changed the management VLAN ID from 1 to 2, I can't even connect to the AP wired from the PC, why does the change matter?
View 2 Replies
View Related
Sep 25, 2012
I have a new 5508 that I am setting up. My first one from scratch.
Interfaces:
managment -> 10.10.10.10 ->dhcp 10.10.10.1
voice -> 10.10.7.1 ->dhcp 10.10.10.1
guest -> 192.168.1.2 ->dhcp 192.168.1.2
Local DHCP (via the 5508) is for the guest network while the management and voice use the Windows DHCP server.
My problem, Voice and guest work fine. I have two SSID's (one 802.1X and the other PSK) that use the management interface that will not get an IP. I have enabled dhcp proxy from the cli on the controller. I tried with the management VLAN tagged and untagged.
View 2 Replies
View Related
Dec 21, 2011
Can a 2504 wlc use a vlan ids of 190X? I have found that it supports 512 vlans but I have not found any restrictions in the id used.Vlan id 190X is distributed by the isp (they have the ASAs in their central site) so if it is not supported I must prepare a vlan transfer between switches.
View 4 Replies
View Related
Apr 10, 2013
What is VLAN Management
View 4 Replies
View Related
Jun 29, 2011
Can I change the untagged vlan on a 1131 to a new vlan. I need to move my management vlan from 10.1.1.1 on vlan 1 , to 172.16.0.1 on vlan 200. I attempted several configuration options including removing the vlan1 ip, changing my new vlan200 to untagged and mirroring it on the switch, and adding my new ip to vlan 1 untagged and then untagging the switch with access vlan 200 on the connected port. Nothing worked.
Below is a sample of what I changed:
interface Dot11Radio1
no ip address
no ip route-cache
[Code]....
View 1 Replies
View Related
Aug 2, 2012
Apparently on older switches you could just enter the "management" command under the new VLAN interface and it would pull the config from the old one, apparently that feature isn't around anymore. I've tried establishing a trunk to the damned thing and trying to switch over that way, but it doesn't seem to work.
View 4 Replies
View Related
Mar 12, 2013
In one of my client location I have deployed one Cisco 3560X (core switch) and one SG-200-18 (access switch). I’ve configured three vlans (vlan 2, vlan 3 and management vlan 1), relevant trunking and I’ve connected two pc to the access switch to vlan 2 and 3 respectively. So far everything (including inter-vlan communication) works fine, except that I couldn’t reach the vlan 1 (management vlan) devices (access switch and core switch) from any pc which is connected to either vlan 2 or 3.
I’ve configured the “port VLAN membership” settings in SG-300 as follows,
Interface mode Administrative vlans Operational vlans
GE 2 Access 2UP
[Code].....
View 4 Replies
View Related
Sep 10, 2012
I'm having some problems with a D-Link switch. I believe it's filtering the management VLAN frames, which is really strange. If you look at the graph, you can see that the D-Link is connected to three switches by trunk links. I'll just use the numbers set in red on the graph to explain what's going on, it's simpler to see.So when I'm connected either to switch 4 or switch 5 (or the others on 5's level) I can use the management VLAN (ID = 1) to connect to all switches above number 3 (including number 3) but I can't get to switches numbers 1 and 2.The only way to connect to those switches is to either connect directly to one of their ports attributed to VLAN 1 or by connecting directly to switch 3. So that's why I concluded that switch 3 filters VLAN 1 frames. It's not switch 4 cause I can get from 5 to 3. But at 3, the frames stop.Also, this only happens for VLAN 1. We have some VoIP phones connected to switches 1 and 2 and their frames can communicate anywhere in the network.
View 12 Replies
View Related
Oct 12, 2011
I got question about Cisco SF300-24P- is it possible to have management vlan in other vlan than in default vlan?I have default vlan 10 and voice vlan 20, I need to reach switch through voice vlan so I need to set up, interface vlan 20 with ip address. I ask these, because in gui, under Management Interface, IPv4 interface,under Management VLAN, I can only choose vlan 10, which is my default vlan, I dont have option to set ,up, in this case, vlan 20 as management vlan.
View 2 Replies
View Related
Oct 20, 2012
i have a small network with Polycom phones connected to the sf300 switch and have the pc's daisy chained via the second switch port on each phone. i have the pc traffic running on the default vlan 1 and the voice traffic running on the voice vlan 100. can i do bandwidth management on a vlan/port basis or is that not necessary. i want to ensure that the voice traffic is never impacted by the pc traffic on the same cable.
View 2 Replies
View Related
Jul 4, 2012
spam up the boards with the same basic CCNA level stuff, but I have a couple of questions about ios differences, limitations, and references. I have the following three switches. One appears to be considerably dated in regard to software version. My confusion/ignorance stems from managing VTP settings.
2924XL 12.0 5 WC8
2950 12.1 22 EA6
2950 12.1 22 EA6
When I set either 2950 switch as the VTP server, and the other as a client, the client inherits the server settings as expected. However the 2924 requires that I go into the vlan database from priv exec and manually set vtp client. That's pretty similar to setting any switch to client mode. The problem I am observing is that after setting the 2924 to client, it still doesn't inherit vtp version settings or pruning settings. I still have to manually configure those. Additionally, if I copy run start the 2924 after making these manual settings, and then reload the switch, all the settings are lost and it defaults back to server mode with all features disabled. From my searches, it looks like vlan information is stored in vlan.dat, but all the documentation I've found is on 12.1 ios which doesn't appear to use vlan database for vtp setup, meaning it might still be an issue, but not one I'm focused on at the moment.
Is the vlan database dumped at reload? I've read vlan.dat is stored in nvram and should be saved after a copy run start, but that is not the case for me.I have since set the 2924 as the server, manually configured the server from vlan database, executed copy run start, and reloaded the switch. Oddly, my manual settings saved from the reload, meaning I only lose settings when the switch is in client mode.Am I missing additional necessary client commands to save the config, or is this just a limitation of either the 2924XL or the 12.0 ios?On a related but completed out of scope topic, without a cisco service contract, how am I supposed to make heads or tails of all the different versions of ios, along with the letter-based features and what-not? I can't even find my 2924 in the list of platforms when searching for ios upgrades.
View 5 Replies
View Related
Jan 21, 2012
I have an HA ACE deployment and all seemed to be working well until I tried to access the ACE via the management VLAN in the one non-system context, no go.The ACE is in one-armed mode with an Admin/System context and one user context (named Messaging). Source NAT has been set up in the user context. All VLANs are in a port channel back to the core switches.I can access the ACE via the Management VLAN in the system context, all OK. I can access the load-balanced servers via the VIP in the user/Messaging context, all OK. I CANNOT acccess the managment VLAN other than ping it (resonds to ping, but telnet, ssh, https, etc. fails).The system/Admin context has a default route to the Management VLAN on the core. The User/Messaging context has a default route to the core switches on VLAN 5, which is the VLAN where the VIP resides.If I change the default route in the User/Messaging context to the Management interface on the core switches then I can access both contexts for management, but then the load-balancing falls over and I cannot access the serverfarm (via the VIP). Traces on the rservers show that NAT is being hit on the ACE and the requests are coming from the real IP of the clients. Put the default route back to the User/Messaging VLAN on the core and NAT is back to what it would be expected to be, and then remote/management access to the ACE is gone.
ACE02/Admin# sh run
Generating configuration....
logging enable
logging standby
logging timestamp
logging buffered 4
logging device-id context-name
[code]....
View 1 Replies
View Related
Apr 29, 2012
We've got a SG200-18 switch that is to be used as a workgroup switch in our environment (SW Version 1.1.1.8). Working with CLI on big and mid-range Cisco-gear over the past two decades I'm having a hard time figuring out the following on the SG200:
o) I want to change the Management-VLAN from the default "1" to the management-VLAN used in our environment. Sure enough I created that vlan in the SG200-config, however when it comes to assigning the management-IP and VLAN for the management interface in the corresponding pulldown under "IPv4 interface -> Management VLAN" the only thing selectable is the default "1". (see screenshots enclosed)So how do I set a management VLAN different from 1?
o) How do I enable telnet/ssh-access to the SG200-18 - I'd be far more comfortable with a CLI-environment?
View 2 Replies
View Related
Dec 5, 2012
I'm trying to figure out how to (or if I can) setup the management interfaces (fa1) on a couple of new 4500X switches. My issue is that the 4500X's themselves are the gateway for my management VLAN (.1 HSRP virtual, .2 and .3 SVIs on the pair of switches).
I would like to assign addresses from the management VLAN to the router Fa1 management interfaces but the software configuration guide seems to note this is not supported (and indeed it doesn't seem to work).
Physically I have Fa1 from core-1 into a port on an adjacent switch. Fa1 from core-2 also goes into a port on that adjacent switch. Both are in my management VLAN, whose SVIs are on the cores themselves.
View 5 Replies
View Related
Mar 10, 2013
We have a small cisco 1800 series workgroup router that seperates our network from the outside world. The data coming into our network goes into the router on interface fa0/1 and comes out on interface fa0/0. fa0/0 is split into 2 sub-interfaces (fa0/0.2 and 0/0.3). These sub-interfaces correspond to a desktop and server vlan on our network. The workgroup router is connected to a 3560G trunk port (we'll call it switch 1) and switch 1 connects to another 3560G (we'll call it switch 2). Recently I was asked to add another layer of security to our network by installing an ASA 5510 firewall and forcing certain types of traffic to authenticate using their domain credentials for our network. The firewall was set up between the router and switch 1 in transparent, multi-context mode. There are 2 security contexts, 1 for the desktop vlan and 1 for the server. Both have the same security settings applied to them since we want the same behavior regardless of whether they are trying to access the servers or the workstations.
View 2 Replies
View Related
Jun 8, 2011
I've got an ASA 5505 running 6.3 I've connected the management interface to our management vlan (which contains switch IPs, ilo's etc)Is there a way to allow access to this vlan from another?
View 1 Replies
View Related
Aug 22, 2011
I would like to push route for admin services (Vlan20) to bypass the firewall via an other connection (CSI to CSE). So my first choice was to create a route-map in (CSI) but I don't know how to do it. On my Firewall ASA, I don't have any Context License, that is why I would like to do it like this.
I have included some part of my initial configuration CSI and CSE and diagram.
CSI configuration (Switch L3 3750) {
interface GigabitEthernet1/0/1
description To ASA
no switchport
[Code]....
View 1 Replies
View Related
Apr 8, 2012
Randomly when I try to access to 2950 from management tools, switch is unreachable, I have to access from other switch and reload 2950.
Problem only is from managemt tool to managament vlan 1 2950.
The strange thing is that management interface is encountering a very fast increase of throttles, broadcast and ignored packets:
2950#show interfaces vlan 1
Vlan1 is up, line protocol is up
Hardware is CPU Interface, address is 0023.3488.fd65 (bia 0023.3488.fd65)
Internet address is xxxxxxxxxx
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
[code]....
It could be a hardware problem?, IOS has been upgraded.
View 11 Replies
View Related
Nov 21, 2011
when I was using image 1.0.0.27, I was able to move the management VLAN from 1 to which ever VLAN I wanted. For some reason, after switching the image to 1.1.1.8, I no longer have that function.
View 1 Replies
View Related
Aug 7, 2011
Any snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.
View 8 Replies
View Related
Mar 2, 2013
Why a 2504 Poe? If it can not be used for AP.
View 10 Replies
View Related
Jan 22, 2013
I'm planning to upgrade our WLC 2504 from 7.2.111.3 to 7.4.100.0 but the cisco site says "WLC Version 7.4.100.0 will need Prime Infrastructure Version 1.3 to be managed, Version 1.3 is not yet available to download at this point of time" Is it something about NCS? we have only 1 cisco WLC 2504 and 6 1142APs.. Also let me know is it possible to go directly from 7.2 to 7.4 ?
View 8 Replies
View Related
Nov 28, 2012
what is the maximum number of APs supported on Cisco 2504 WLC?According to the Data Sheet it is 75:
[URL]
But according to the config guide it is 50:
[URL]
I believe the correct number is 50, but I just want to be sure.Is this a software limitation?
View 8 Replies
View Related
Aug 29, 2012
I've problem with a WLC 2504. Some Clients like phones and Thin Clients get an IP 0.0.0.0.Software Version is 7.0.235.0. Test with a Laptop seams to be OK. Some printers also got an 0.0.0.0.Around 30% are not OK. also had the log: Impersonation of AP with Base Radio MAC 00:yy:yy:yy:yy:yyusing source address of 00:xx:xx:xx:xx:xx has been detected by the AP with MAC Address: 00:yy:yy:yy:yy:yy on its 802.11b/g radio whose slot ID is 0 The problem is, I cannot go to 7.2 version because I have 2 x AP 1231 and 2 x 1242 AP's.1231 AP's are not anymore supported in 7.2 Version.
View 14 Replies
View Related
