Cisco Switches :: SF 300-48P How To Implement Route
Oct 13, 2011
We recently purchased a SF 300-48P to replace a Layer 3 3Com switch that died. I've sucessfully put the switch into Layer 3 mode and assigned ip addresses to each of the VLANs but I cannot figure out how to implement routes for those. Here's some info on our network and what the previous switch had. [code]
Not sure if this can be translated into the Cisco or not.. If i try to create an IP route like these i get errors that the Gateway can be a route.
View 5 Replies
ADVERTISEMENT
Oct 31, 2012
I currently have two SGE2010's with a 4-port LAG configured between them. I'm looking to add another two SGE2010's and I want to add redundancy at the same time. The switches are currently in standalone mode. I don't have fiber connectors and was planning on just using copper for the uplinks.
My questions are:
- Is it possible to use stack mode in conjunction with 4-port LAG groups to create redundant 4-port links between all of the switches? The documentation says that ports 24&48 are reserved for stacking - does that mean I can't specify a LAG instead?
- If 4-port LAGs aren't possible, does that mean that these switches max out at 1Gpbs uplinks if you use stack mode?
View 4 Replies
View Related
Mar 13, 2013
(eth ports routing only) and a layer 2 switch into a cluster of two layer 3 switch clustered. I have looked at Cisco 3550 EMIs with HSRP but I would like to implement based on newer models of Cisco switches.
View 6 Replies
View Related
Mar 7, 2012
I am new to VLANs and Cisco SMB switches. I have a new SGE 2010P switch and i am trying to configure different VLANs, one for data, one for Voice and the other for server.
Is there any tutorial on how to configure VLAN, by the way i tried to used the web interface and admin guide, it totally confused my understanding of Vlans.
View 5 Replies
View Related
May 24, 2006
I am trying to implement IP SLA. Can I implement it on layer2 switches?
View 5 Replies
View Related
Jun 21, 2011
I have SGE2010 switches and I want to implement Multiple VLANs. Im a newbie and starting to study VLANS's.
I want to implement 5 VLAN's on my test lab network and here as follows:
192.168.1.x default
192.168.2.x
192.168.3.x
192.168.20.x
192.168.100.x
The .1 is exclusively for my test-lab servers.
The .2 is general test-lab Win-XP workstations.
The .3 is general test-lab Win7 worstations
The .20 is general test-lab production worstations
The .100 is for test-lab IP PHONES.
View 4 Replies
View Related
Feb 10, 2011
How to implement ipv6 on windows 7
View 1 Replies
View Related
May 1, 2012
I want to implement SPAN or RSPAN of a vlan. Can this be done with the SGE2010P? I can't find the configuration guide on the Cisco Web Site.
View 1 Replies
View Related
Apr 24, 2011
How can i implement networking in my THREE floor office by using routers and switches?
View 1 Replies
View Related
Mar 25, 2012
I have a SG300 Switche working in layer 3 mode.I configured 3 VLANs on the switch, assigned all ports, given IP addresses to VLANs interfaces, etc.Now I want to implement ACL to permit or deny access between vlans and hosts.Can I apply an ACL to a whole VLAN (in or out) like Catalyst models?I mean apply the ACL to the entire vlan or the only way in this model is to implement that ACL port by port?Every time I have a new port configure to work in a Vlan I have to implement the ACL?
View 4 Replies
View Related
Dec 6, 2012
I have the following set up, at one of our sites:What I would like to do is take non 10.x.x.x web traffic, and pipe it through the ISP2 link, and keep all other 10.x.x.x traffic over the main ISP1 link. I would like to set this up on the L3 3750's that we have. Here is my configuration for the 3750's (IP's have been changed for security):
track 222 ip sla 222 reachability
track 223 ip sla 223 reachability
ip access-list extended INTERNETTRAFFIC
permit tcp 10.1.1.0 0.0.1.255 any eq www - Internet LAN subnet
permit tcp any 10.1.1.0 0.0.1.255 eq www
permit tcp any eq www 10.1.1.0 0.0.1.255
[code]....
I'm applying the policy route-map to the VLAN interface, but do not see any traffic, once I apply the interface. I'm not that experienced, with route-maps?
View 2 Replies
View Related
May 17, 2011
I need to move the client machines off of the 3750 (and their DHCP dependency on it) to the SGE2010 and absolutely route their internet traffic out through the outside interface on the 5505. They must also be able to communicate back into the internal environment in order to communicate with the production servers.
The clients currently use .254 addressing through a dumb dell switch to the 3750 but I am trying to migrate them over slowly to the .253. I know that the 2010 will not do DHCP, so I am putting a DHCP server on that switch right now. The 5505 won't let me add an additional nameif statement onto one of the other eth0/x interfaces and I'm not sure if that has anything to do with it's capabilities to act as a DHCP server (it's not an option in the ASDM) or it's ability to serve as the internet gateway for the 2010 clients. (Side notes: The 5505 has a base license and is currently also connecting 1 site to site VPN. As is the 5520, so all of it's interfaces are used as well).
I statically assigned a moved client with a .253 address and plugged it into the 2010. I have tried giving the 2010 both a .4 address and a .253 address but neither will allow me to ping any of the addresses on the 5505. The 2010 shows automatic routes to the two subnets and I set it's default route to 253.1. The link between the 2010 and the 3750 works - clients receive a .254 address from the 3750 and can get out to the internet via the 5505 and reach the production servers as well.
Why won't the 2010 see the 5505 as a gateway and allow clients to get to the internet and also traverse the 3750 when they need access to the production network?
The reason why I dont' just connect the two swtiches and call it a day is because I also need the production servers to ALWAYS go out/receive web requests via the 5520 outbound/outside interface. I'm having such a hard time wrapping my head around why i can't get my clients moved over to the new switch, I haven't even grasped how I'm going to do that yet.
View 4 Replies
View Related
Jul 19, 2012
We are planning 3 Internet Connections into our building. 1 will be for actual Internet traffic, 2nd for Voip phone system, and 3rd for internal network for Active Directory...etc. Oh the AD servers are controlled by another business so technically this line is still considered and outside line and is a T1. What I need to know is how best to make this all work so that our internet phones use the VOIP system, computers can log into the domain and access that network but use the Internet network for actual internet traffic? We were considering a series of managed switches and creating 3 VLAN's but I'm thinking we instead need a new router that all 3 networks connect to and dishes out DHCP to computers and phonesn example network is below.192.168.1.x ----> Internet (all computers use for internet traffic)72.10.10.x ----> VOIP (All physical and software phones use this network)10.10.10.x -----> Connection to external company that controls our network and has domain controllers, mainframe...etc.
View 2 Replies
View Related
Jul 27, 2011
We have recently purchased a Cisco SG300 and have been configuring it. [code] The VLANs have ACLs set up to prevent any communication between the Holly and Tempo VLANs (and their associated WAN VLANs).Each VLAN has a WAN available for it's use, which connects to external networks (including the Internet).In order to facilitate this, we have set up all the necessary ACLs and routes and confirmed that this all works.However, the problem comes when we assign the static routes that specify the default gateways.We add the two static routes below:
-0.0.0.0 next hop 10.10.200.254 metric 1
-0.0.0.0 next hop 192.168.200.254 metric 1
In this case, only one of the VLANs has WAN access. It is either Holly or Tempo (it can be either if the order the static route is added is changed).What we need is to force Holly to use Holly WAN and Tempo to use Tempo WAN, but we cannot see a way of doing this.Effectively, we want the following static routes: [code]
View 2 Replies
View Related
Jun 24, 2011
I've enabled antispoof on all interfaces on asa 5510.If you start a traceroute to a network on the default route, everything works, since replies comes to an interface with route 0.0.0.0/0 defined.If you start a tracer route to a network that is NOT on the default route (let's assume coporate MPLS), you only get response from first carrier router, the other are discarded because of anti spoof violation.
I have ICMP inspection and icmp-error inspection enabled.
View 1 Replies
View Related
Jan 20, 2011
I have a Netgear GSM7248R switch with 5 different Vlans including th management Vlan. Each of the vlans are connected to my layer 3 switch for routing. I want to access the management vlan form any of my Vlans so my layer two switch can be detected by my snmp manager.
View 3 Replies
View Related
Feb 9, 2013
Can we implement BGP without IGP Protocol ? If yes, then how can we do it ? If no, why ?
View 11 Replies
View Related
Jul 31, 2011
We are attempting to implement an ASA 5520 with a new ISP. Based on the limited routing needs, I believe we can use it as the router as well. I am familiar enough with routers, but the ASA is obviously a different thing.
The setup looks like:
ASA Version 8.2(1) !
host name Cisco
interface GigabitEthernet0/0description Internet name if Outsidesecurity-level 0ip address 69.XX.46.1 255.255.255.252 !interface GigabitEthernet0/1
description DMZnameif DMZsecurity-level 0ip address 69.XX.56.1 255.255.255.240
!interface GigabitEthernet0/2description Localnameif Insidesecurity-level 15ip address 10.0.XX.XXX 255.255.252.0
[Code] .....
1) Outside 0/0 connects to MRV from service provider (Public)
2) DMZ 0/1 connects to outside switch with servers (Public)
3) Inside 0/2 is LAN (Private)
A) Based on a completely default config and aside from setting the routes to send traffic from inside to outside, and outside to DMZ, what is the next step?
B) What should the interface security levels be, I am unsure what they should be or why...?
Based on the initial config with interfaces set as above, I cannot move traffic through.
View 5 Replies
View Related
Oct 21, 2011
Today we have a simple ASA-5520 SVC setup with just one connection profile and one group policy. Authentication (2 factor – AD + SMS) is performed by RADIUS. We would now like allow access to this VPN service only if you reside in a particular group in the MS AD. From what I understand this can be accomplished through DAP. Either by matching the LDAP attribute “memberOf” or RADIUS id 146. I’m I right? Can I still perform authentication using RADIUS and then DAP using LDAP or must I use DAP using RADIUS?
View 3 Replies
View Related
Feb 21, 2013
How to implementation LAN network
View 2 Replies
View Related
Oct 15, 2012
Is it possible to implement ACLs in layer3 switch??
View 4 Replies
View Related
May 18, 2012
I have some Cisco 2651 routers, I was trying to implement MPLS on those routers, Can i accomplish this upgrading newer IOS version? link to download the supported IOS.
View 2 Replies
View Related
Aug 20, 2009
We want to implement an IPSec VPN between two routers cisco 2800 IOS version of what we need.
View 4 Replies
View Related
Apr 26, 2012
I am looking to upgrade an 1812J router to 1921/K9 router with 8-port double wide switch port.What's the best/easiest way to migrate the config? (We have access lists, vlans, etc. configured on the original device)Also, I'm looking for a way to prioritize traffic from an external site on the internal LAN. Reason being that I would like to prevent dropouts of interent streaming radio when Internal LAN traffic is high. If so, what's an easy way to implement on 1921?
View 1 Replies
View Related
Nov 27, 2011
I want to select catalyst 3560G for my network. But IOS SLB need to be implemented in my network. I only know catalyst 6500 series can support this feature and i am not sure whether 3560G can support this feature. what platform and IOS version i need to implement IOS SLB?
View 1 Replies
View Related
Apr 9, 2012
Required by regulations to implement CoPP on our routers, I installed the following configuration on a C2811 router pair with integrated DSU/CSU cards connecting a point T1. STAC compression(software) is configured on the serial interfaces and the link is often congested.
[code]...
This configuration severely degraded the IP traffic flow and I had to remove it. Not having any practical experince with CoPP.
View 1 Replies
View Related
Aug 27, 2012
We are in the process of implementing secondary ISP to our ASA firewall and We would like to run both ISPs in parallel so we can test until we finally cutover?
View 2 Replies
View Related
Jun 3, 2012
We are trying to implement the ZBF on our router to assist us in limiting the intial impact of DDOS attacks.We have configured the below and it appears that it's not working, as when un der attack the statistics don't increae.
[code]...
View 2 Replies
View Related
Sep 27, 2011
one of my customers wants to implement VoIP in his existing DMVPN Network Topology. I have read about the "Per-Tunnel QoS for DMVPN" but when it comes to configure it on my hub router (Cisco 7206VXR with c7200p-advsecurityk9-mz.124-15.T14.bin) I am lacking the option to set the "ip nhrp map group" command.
My question now is, is it generally not supported by the 7206VXR platform? Or can I get the option by upgrading the IOS to a newer version? If so, which one could I use ?
View 2 Replies
View Related
Nov 29, 2012
I have 1 server where i enabled dhcp server and active directory on it . I still have to install something like ISA server on it as isa doesnt support 2008 r2. point me out on the networking , like how should i connect the clients to the server. And how the wireless router and switch should be connected to the server?
View 1 Replies
View Related
Feb 3, 2013
I am trying to implement an etherchannel on a cisco 2901 (IOS 15.1). i have already created the port-channel but i cannot assign the gig interface to the channel group.
View 1 Replies
View Related
Sep 13, 2011
I need to implement the backup between two sites I have router 2800 which is having a point to point connectivity with the far end.At the far end there is no router ,only one firewall is there on that firewall one access-list is there to allow the traffic .To implement the back up link i have created a site to site vpn .But the problem is as soon as the tunnel is establised .For the time being i have removed by site to site config from both firewall.
View 7 Replies
View Related
Nov 22, 2011
I have a 3560-48 switch running Cisco IOS Software, C3560 Software (C3560-ADVIPSERVICESK9-M), Version 12.2(44)SE3 and i need to implement basic QOS commands to the fast Ethernet interfaces as well as the gig interfaces and Also I need to create port channels on the switch and need what the port channel syntax are as well for that particular IOS version?
I have only read only access and i can't see what the QOS and Port channels syntax should be for that IOS version.
View 3 Replies
View Related
