Cisco Wireless :: 1600 Series AP To Reset Before Joining To Controller
Mar 3, 2013
I have new 1600 series Access Points. I am trying to join those APs on controller but unable to join.
After doing config reset using mode button, I was able to join only. Please find the logs or error messages below:
*Mar 4 18:53:13.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.2.241.50:5246
*Mar 4 18:53:14.063: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Mar 4 18:53:14.079: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 4 18:53:14.123: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
[Code] ....
View 6 Replies
ADVERTISEMENT
Jun 13, 2013
how to setup the Aironet 1602 (AIR-SAP1602I-E-K9) I have tried accessing it by various IPs like 10.0.0.1 or 192.168.1.254 but none of them work also when I monitor the connection using Wireshark I can't find out what its IP is.
View 4 Replies
View Related
Feb 6, 2013
I have a 2500 and I have successfully joined a 1600 AP to it; however I have noticed that I cannot enable CleanAir in the Global Parameters with just the 1602 AP joined. This feature was enable when I had my 2602 AP connected.So, is the problem that the 1602 doesn't fully support CleanAir? If that is the case, how do I enable CleanAir Express or is that something you can even enable thru the GUI?
View 15 Replies
View Related
Jan 8, 2013
I have a 2500 and I have successfully joined a 1600 AP to it; however I have noticed that I cannot enable CleanAir in the Global Parameters with just the 1602 AP joined. This feature was enable when I had my 2602 AP connected.So, is the problem that the 1602 doesn't fully support CleanAir? If that is the case, how do I enable CleanAir Express or is that something you can even enable thru the GUI?
View 9 Replies
View Related
Apr 2, 2013
My customer has an 1131AG AP, andhas Problems with joining to the controller. I did a debug and have the following output. The WLC (5508) shows the AP with Primary SW version as 3.0.51.0. this Release does not showup in any compat matrix! It seems to start downloading the software. after a while it stops with the bolded output, twice the same Bytecount!?
*spamApTask0: Apr 03 09:55:59.998: 68:ef:bd:94:e7:9c 5179392 Bytes Transferred to AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:56:00.097: 68:ef:bd:94:e7:9c Received LWAPP
[Code].....
View 22 Replies
View Related
May 9, 2012
i have 1240 series access points which is not joining controller 5500 series. [code]
View 12 Replies
View Related
Aug 7, 2011
I am trying to join my 1130AG-E-K9 AP to my 2016 WLC, but it is stuck in a boot loop and will not connect to the controller. [code] I found some details here: url... but I'm not sure what it means that I have a 'SSC AP'. I am not local to this AP, though I do have a console connection to it-what do I need to do to get it working again? It just continually goes through this error and reboots every 30 seconds or so, so it's useless at the moment.
View 3 Replies
View Related
Jul 28, 2011
I upgraded a controller yesterday 5508 it went from a low code version 6.x to 6.0.196.0 then to 7.0.116.0. However although all the access points joined code 6.0.196.0 they refused to join 7.0.116.0. The aps are all 1242s.
The country codes etc were all fine so I do not understand what was going on.
*spamApTask0: Jun 26 16:07:44.734: 00:3a:99:db:f3:20 Discovery Request from 10.0.0.183:55065
*spamApTask0: Jun 26 16:07:44.734: 00:3a:99:db:f3:20 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 25, joined Aps =0*spamApTask0: Jun 26 16:07:44.735: 00:3a:99:db:f3:20 Discovery Response sent to 10.0.0.183:55065
[code] ......
View 5 Replies
View Related
Sep 22, 2011
how to reset nokia siemens 1600 modem as i have forgotten its username & password which i changed?
View 1 Replies
View Related
Nov 5, 2012
We have 3 5508 WLCs (A, B, & C) and several LAPs (1140, 3500, 3600). The APs learn the controllers IP addresses through DHCP Option 43. When we setup a new site we put the IP address of the controller we want the AP to join first. Lately, I've noticed that regardless of which WLC IP I put first when I setup Option 43 the LAPs are always joining a particular controller.
View 6 Replies
View Related
Dec 11, 2012
I have some remote 1142s that I converted to LAP last night. They are not joing a WLC, but I they are online and I can ping them. Telnet or SSH is disabled by default (WHY???). What can I do to figure out why these access points are not joining the controller?
View 17 Replies
View Related
Jul 6, 2012
I am trying to configure new 5508wireless controller, AP 1042N model access points are able to receive DHCP IP address from Controller, but not able to join them.
View 11 Replies
View Related
Feb 19, 2013
I have been searching through the cisco docs for a while and i just cant seem to find this info. Can I run aironet 1600's with my wism running 7.0.116? Also, could I run my 1130 series ap's with a wism2? Basically, what is the minimum code level for a lightweight 1600, and what is the maximum code level for a lightweight 1130?
View 3 Replies
View Related
Mar 15, 2013
I have Cisco 5508 WLAN controller v7.4 and i have lap 1310 and it is not joining to this lan controller. What to do? How to join this lap to this lan controller? or how to convert it to autonomous because i dont find mode button on this access point?
View 6 Replies
View Related
Aug 27, 2011
I am facing problem with an outdoor access point AIR-1522-K-E series which is unable to join a wirless lan controller 5508. The wireless AP is able to get IP address from dhcp server and discover the Wireless controller IP address. After this i see following status messeges on the console of AP.
*Aug 27 11:04:19.767: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 27 11:04:21.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.2.64.50 peer_port: 5246
*Aug 27 11:04:21.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Aug 27 11:04:21.707: %CAPWAP-5-DTLSREQSUCC: DTLS connection created successfully peer_ip: 10.2.64.50 peer_port: 5246
[Code]...
View 10 Replies
View Related
Mar 6, 2012
Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies
View Related
Mar 13, 2013
I have Cisco AIR-LAP1310G-E-K9 access point and 5508 wlan controller with version 7.0.220 and it is joining to the WLAN controller. I have enabled dhcp in the lan controller and i dont have external dns server. How to fix this issue? Can this LAN controller version will support this access point? My Lan Controller Management IP Address is 10.10.10.5 find the below configuration of 1300 access point.
AP001d.4513.dd68#reloadProceed with reload? [confirm]
%SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command.%LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.flashfs[0]: 4 files, 2 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 7741440flashfs[0]: Bytes used: 2052608flashfs[0]: Bytes available: 5688832flashfs[0]: flashfs fsck took 14 seconds.Base ethernet MAC Address: 00:1d:45:13:dd:68Initializing ethernet port 0...Reset ethernet port 0...Reset done!ethernet link up, 100 mbps,
[code].....
View 6 Replies
View Related
May 13, 2012
I have a couple 3600s that don't want to join. One i and one e that are both doing the something. It is able to find the controller via layer 3 discovery but it is acting like it is a mesh AP when it tries to join the controller.
From the 2500 controller (running 7.2)
*spamApTask2: May 13 12:03:05.272: f0:f7:55:ae:xx:xx Mesh AP username f0f755aexx xx.
*spamApTask2: May 13 12:03:10.739: f0:f7:55:ae:xx:xx spamProcessJoinRequest : RA
P, Check MAC filter
From the 3602i
flash:/mesh_start_cfg.txt: No such file or directory. The filesystem containing the variables may not be initialized yet.
I should note that 3500 APs are able to join this controller. The field guy is going to try to add the MAC address to the filter list when he gets back out on site to see if it allows it to join.
View 3 Replies
View Related
Apr 4, 2013
I am trying to setup a 2504 Wireless Controller with a few AIR-AP1262N-E-K9 Access Points. But i'm having trouble getting the access points to connect to the controller.The controller and AP's are setup at a local network at one of my customers. They are part of a quite large organization and are therefore connected to some of their other divisions in different contries via MPLS. The DHCP and DNS servers are therefore on a different subnet.I have confirmed that the Access Points do get a correct IP from the DHCP server and that i am able to ping from the controller to the AP. When looking at the controller it does not receive any join requests from the AP's. I have setup a console connection to the controller and 1 AP, so i can view debug information.Most guides mention that you can run different LWAPP commands from the CLI on the AP like show lwapp for example. But i am not able to run any of these LWAPP commands on my AP.
View 8 Replies
View Related
Sep 23, 2010
how to setup the 5508 Series LAN wireless controller. The online documentation are not details. What different between Service Interface IP and Management interface IP. The device IP is using what type service or management interface.
View 2 Replies
View Related
Aug 2, 2011
I've download a login.html into the controller successfully, but when I preview the page there isn't an accept button. Do I need to create the accept button with the html file or is there some place I need to enable on the controller itself. After download the .tar file I reboot the controller but no luck. I also create a java script button redirect but it didn't redirect to where I needed to go. It just stuck on the splash page.
View 3 Replies
View Related
Jan 17, 2012
We have upgraded to latest IOS but observed this box is hitting a bug which was resolved in the earlier releases but not seen in 4402.
Is this related to hardware issue or a software bug only.
CSCtg94715
CSCtk83586
CSCso90721
Error! Software watchdog on task dot11b expired! Reaper Reset: Task "dot11b" missed software watchdogError! Software watchdog on task apfMsConnTask_0 expired! Reaper Reset: Task "apfMsConnTask_0" missed software watchdogError! Software watchdog on task apfReceiveTask expired! Reaper Reset: Task "apfReceiveTask" missed software watchdogError! Software watchdog on task radiusTransportThread expired! Reaper Reset: Task "radiusTransportThread" missed software watchdogError! Software watchdog on task ccxL2RoamTask expired! Reaper Reset: Task "ccxL2RoamTask" missed software watchdogError! Software watchdog on task dot1xMsgTask expired! Reaper Reset: Task "dot1xMsgTask" missed software watchdogError! Software watchdog on task spamReceiveTask expired! Reaper Reset: Task "spamReceiveTask" missed software watchdogError! Software watchdog on task dtlArpTask expired! Reaper Reset: Task "dtlArpTask" missed software watchdogReaper is kickin' into high gear Task dtlArpTask is consuming 0% CPU! (0% user, 0% system) Frame 0: 0x10004708: sighup_handler+84
************************************************************
* Start Cisco Crash Handler Serv *
************************************************************
Sys Name: HJ_Wireless_Controller
Model: AIR-WLC4402-50-K9
[code].....
View 2 Replies
View Related
Jun 11, 2012
I have a 5508 WLC licensed for 100 APs. I have 1 - 1042 LAP connected for testing. I have DHCP configured for the AP, and it gets an address of 192.168.254.100/24 - the controller's management interface is 192.168.254.99/24. I can see that the AP is getting an IP and I can ping it from the controller. However, I simply do not see the AP associating. I enabled capwap debiugging and watched the events, but I didn't see anything crazy that clued me in. What am I doing wrong?
The controller is v6.0.199.4
Every time I have set these up in the past they have been pretty straight forward. I haven't gotten too deep into the config on the WLC becuase I don't want to cause more issues.
View 2 Replies
View Related
Jan 13, 2013
I am trying to reset my 1522 series lightweight access point to factory default.On the box,there is no any mode button.Actually password is not set to Default and need pasword recovery on this device.If you have any experience on this lightweight access point that let me know.How I reset device to fectory default.
View 1 Replies
View Related
Apr 17, 2012
I have a customer whom has six LAP1131AG-K9 but no controller and they are interested in one of the new 2500 series, specifically a AIR-CT2504-5-K9 with a 5 AP add-on license to bring total AP capacity to 10. I can't determine clearly if this controller will work for these older AP's prior to them making the jump to 802.11n via the 3500 or 3600 series, looking to the community to confirm.
View 3 Replies
View Related
Oct 4, 2011
We have 4 1142N LAPs that I want to divide between an internal wireless and a guest wireless network using the controller. Currently all of the APs are on an established internal network, but I want to migrate one over to a test guest network before buying more LAPs to augment the networks further. Currently the port connecting to the WCS from the 3560 switch is configured as an access port using VLAN 10. Whenever I make it a trunk port carrying VLAN 10 as well as the other ports we will be using for the guest and ap-manager networks, I lose connection with the controller. To me this implies that the port on the controller is configured as an access port as well. In the documentation I found for the controller it states that by default the ports are al configured to be trunks, but it appears as though something was changed by the previous tech. All of the APs are connected to other switches, not to the controller itself.
1) How can I get the port on the controller back to being a trunk port
2) Can I use the internal DHCP server for the guest network if the subnet is different than the management subnet, or will I have to use another external server and relay/proxy it through the controller to give guest clients IP addresses?
View 2 Replies
View Related
Jul 5, 2011
The Release Notes for 7.0.116.0 of WLC 5500 has a table which title is "Client Type", and it shows wireless adapters. My question is,
what kind of customer means? Wireless clients or clients for an specific application? If it was the first option, does it mean tha just this adapters could connect to my wireless network?
View 1 Replies
View Related
Apr 21, 2013
Looking for some training on the 2500 series controller and 1142 or 1040 AP's preferably.
View 10 Replies
View Related
Dec 19, 2009
We are facing an issue with a customer where a Cisco 4400 Series controller is blocking the 802.11a/n Radio Interface of a 1250 AP. The radio shows as down on the controller GUI. The error message on the GUI is that the 'Regulatory Domain' is not supported. This can be seen from the attached screenshot. Also relevant parts of the WLC configs are attached. WLC: Cisco 4402 WirelessWLC Country: SADevice: Cisco Lightweight Access Point 1250 (LAP) is controlled through the 4402 Cisco Wireless LAN Controller (WLC)The operating system version of the LAP: c1250-k9w8-mx.124-18a.JA version of the WLC: Software Version 5.2.178.0 The problem is that the controller shows that the 802.11a/n Radio Interface in Radio Slot # 1 is always down , the customer tried to manually 'no shut' the AP interface from the console and it worked , but obviously this solution would not work as the configuration cannot be saved (LW AP).
View 12 Replies
View Related
Mar 4, 2013
If the 2600 series access points are compatible with a 4404 controller running 7.0.235.3 code? I was looking for a compatibilty matrix for the AP to controller to code comparison but couldn't find one.
View 1 Replies
View Related
May 20, 2012
I recently upgraded our controllers to the latest version 7 software, as I read this was one of the requirements to get them to connect. But I am not having any luck getting into a controller. Normally I plug them in to the network, they pop into the controller listed as something like AP5057.a844.xxxx and then I can finish configuring them, but a static IP on them, etc. This is the first of this model AP I have tried to deploy, so I am wondering what is different with these. or what I might be missing in the default config in the WLAN controllers. Niether of which are set to "Master" either.
View 10 Replies
View Related
Jun 27, 2012
I have Cisco 3800 series router it needs user name and password to access through terminal I don't have the user name and password. Need To reset the password.
Terminal screen shot is attached here you can see that.
View 3 Replies
View Related
Aug 16, 2011
I have a cisco aironet 1300 series and i need to reset it back to factory default. the directions say push the mode button while the access point is off and then turn it on while the mode button is down.
View 1 Replies
View Related
