Every other day and sometimes everyday I have an issue where my network slows down in one area at around the same time of day 12:00pm. I am using Solarwinds and I don't see anything significant showing up.
View 2 Repliesi have had my dir-655 one year now, have never had wireless problems with it until now.my notebook's internet gets very slow somedays, i just restart my router and then internet speed works normally.i have:
Hardware Version: A4 - Firmware Version: 1.32EU
We have a VPN 3000 that we use to connect. We are recieving reports that some of the users are connected but after a set period of time they are disconnected. Is there any changes that I could look at in the VPN 3000 that could point me in the right direction.
View 3 Replies View RelatedSo, I just upgraded my mobo/cpu (Z77A-G45 and i5-2500k) and I'm having an issue with my connection as it seems to drop every 5 to 15 minutes constantly and have no idea what exactly is wrongThe kicker is my old mobo did the same thing and I had to do something in win7 to fix it (not sure if it was the drivers or what) but I just can't remember what exactly.
View 1 Replies View RelatedI have a Cisco 2911 router with 4 T1 connections. Two are set as a multilink and the other two are for two other locations. The router will run fine, but after a month I cannot ping the gigabit ethernet 0/0 interface. I would have to manually reboot the router to get it to respond again. Before I noticed a lot of interface discards which would shutdown the 2911 and a manual reboot would be needed, but for this time it isn't the case. Where would I start with this the memory and cpu usage are fine.
Here is the config:
Current configuration : 2905 bytes
!
version 15.0
[Code].....
I have just bought an E3000 router when my old router died last week. I am having two problems:
1. The data rate slows down after a period of time (long message trail elsewhere)
2. I cannot see everything on the network.
I have several Win 7 computers, two win xp computers, three NAS devices (linux based), and a printer sitting on the network, along with two switches to cope with all the traffic (not to mention iPods, iphones etc.)With my old router, I couold see everything plugged into the network from my main Win 7 computer. (note: the win 7 network map does not always work, but the windows explorer window of the network always showed everything).With the E3000 router, I can only see 1 or 2 of the devices on the network. If I reboot the router, then sometimes all of the devices appear on the windows explorer window (sometimes not)I am running a workgroup (not a domain) and i am not using win 7's homegroup because that will not work with the non-win 7 devices.Is there a setting that will see all of the devices in Win 7 (either on the router or on the computers). I suspect it is a router issue as it worked with my old Zyxel router.
I have a Cisco 3845 with the archive command configured:
archive
path tftp://x.x.x.x/$h
write-memory
time-period 60
The archive command works with the execution of the write mem, but with the "time-period" doesn't work.This is the show version of my 3845:
NTP_Server#SH VER
Cisco IOS Software, 3800 Software (C3845-SPSERVICESK9-M), Version 12.3(14)T7, RELEASE SOFTWARE (fc2)
Technical Support: [URL]
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Thu 23-Mar-06 01:59 by pwade
[code].....
I've bought a "WAG160N v1.0 Annex A" almost 2 years ago. I never used it's wireless feature untill we moved our house. Now it's like 4 month I'm using its wifi feature and I've got to admit I'm really frustrated by its functionality!
For months the modem just dropped wireless connection constantly in various time periods. Somtimes it went like 2 days without any problem but some other times I had to change channel every 15 minutes for it to get back working. And yes it didn't get fix until I changed the channel, otherwise clients had to wait several hours for a 50/50 chance of reconnection. Now It's two days the changing channel trick no longer works. I tried all channels and even put my notebook next to the modem but no luck. The notebook sometimes connnects to the access point but disconnects after a few seconds. Somtimes it doesnt even detect the SSID of my WAG160N modem. Some friends suggested that the wireless hardware of my modem is broken and no longer works but I'm eager to know if it is broken why is it still broadcasting and sending signal.
I've tried everything from upgrading and downgrading firmware to turning on and off the modem several times and changes modem position. And even tried the G-only 20MHz mode.We are at a very crowdy place. Using inSSIDer I could pick about 15 other access points. Only few of them are using Wireless-N, most of them are using Wireless-G.This is the inSSIDer diagram of my WAG160N modem from a client: [code]
Basic info: SBS 2008 (64bit), XP-sp3 (32bit) workstations, gigabit switch, SEP. App is Sage Masterbuilder.Network config: Server is 1gb to switch over CAT6. All the workstations are 100mb over CAT5. SEP is set to exclude all pertinent files on both the server and workstations.Problem: The program is called MasterBuilder and does job costing and much more. In the job costing feature there is an option to "Compute" job costing. In version 16.x, when the "Compute" was performed the task was done very quickly. After an upgrade to version 17.x it is very SLOW. According to tech support, our network is at fault since it is a database function over the network.Troubleshooting done: Tech support blamed our network speed (100mb) and switch. We had a Netgear 100mb switch so we replaced it with a GB switch however the cabling will not support GB. Being a managed switch I set all the ports to 100mb except the server port. Even tried the server plugged into a 100mb port and no change. I am confident there are no speed issues on our network. All other programs perform flawlessly. ACAD, Exchange, data transfers and many other high data use programs work perfectly. I updated the network card drivers in the server as well. There are no performance or resource issues on the workstations. I monitored the network traffic at the workstations, server and switch with no issues and about 2.5% utilization during the slow "Compute" process. The switch shows no errors at all, no collisions, no dropped packets, nothing. I also disabled the SEP.
During testing and while the slow "Compute" was going on, I copied a large folder (400mb) from the server to the workstations see the impact on network utilization. As soon as I start the copy process the "Compute" process speeds up to normal and zips by as it should. As soon as I cancel the copy process the "Compute" drops right back to very slow.
My Web application is running in a weblogic server. It is a java based application. Every day from 10 am to 12:30 pm, it is really slow. During initial days, I believed that the user rate is high at that time and so it is slow. But it is slow during weekends alsoI tried force garbage collection and restarting the server but its of no use. I am using 100 threads. After 12:30 the idle thread count could be seen upto 80, but between 10 am to 12:30 pm, all threads are used and my queue length is increasing.
View 1 Replies View Related my switches layer 3 intervlan routing performance is dropping.What would cause this performance drop? I am not pummeling the switch with massive transfers constantly like an enterprise envirnoment would do or a colo center.
[code]...
I have a problem with MSE tracking client in my network.What we have:PI 1.3 with evaluation license (temporary)MSE 7.4.100 with 3k device licenses (hardware appliance 3355)WLC 5508 7.4.100.For now MSE is reacheble from PI and WLC, all setings are synchronized, NMSP status is active, mse assigned for maps and synchronized, on map we have 3 APs, but in Contex Aware tab we didnt see any tracking devices, all counts 0.
View 11 Replies View RelatedI am facing a proble in wireless connection speed that is getting very slow at a specific time, i.e., from 12pm to 2pm and from 9 pm to 2 am. The service is unlimitted type contract
View 1 Replies View RelatedMy company thus cuts off my subscription before the month ends.My family and I use a total of 8 devices on our home wireless network; 3 laptops, 4 iPads, and a Galaxy phone.My router/modem home page shows me the total amount used by all users.. I use a huawei LTE B593 router.
View 2 Replies View RelatedWhen I start-up my computer, it takes over an hour to find my router on my computer (Not on my brother's computer, or the computer upstairs). Once it does, it connect perfectly. This is very annoying because I do not have a lot of time anyway to work/play and when I do, it takes over an hour to find the router.Recently, I have been having HUGE lag spikes, constantly disconnecting from games and skype calls.
View 1 Replies View RelatedEach time I'm rebooting my E3200 device my ping to my ISP is 20ms. Few hours later the ping goes up to 300-500ms.Than I reboot again and the ping is going down to 20ms again.
View 5 Replies View RelatedHaving issues with HTTPS sites being very slow after applying KB2585542? Once you remove this Microsoft patch everything returns to normal. It appears that the CSS does not handle the split-ssl requests properly. I have opened a TAC case but am not really getting anywhere as we seem to be the only company that is having this issue.
View 2 Replies View RelatedOne of my laptops is having a connection problem. I have 3 other laptops that can connect perfectly with my router, and normally there's only 1 laptop that is connected to my router. The laptop with the slow connection (takes 5 HOURS to load a website, sometimes will not even load), i re-installed the OS, and installed all the drivers needed, and it still wont work. it shows strong connection to me, and im sure the password for the router is right. below is the ipconfig/all information. Having this problem for 2+ weeks now!!! I think this problem started when i restored my router to factory setting, my router is Netgear WGR614v6.
View 14 Replies View RelatedI have a WAG160Nv2 with Firmware Version:V2.00.20 Two problems
1. Slow wireless speed - only 2Mbit - with cabte up to the lines max 15Mbit
2. The routers system time is wrong - it says " 03-01-2000 02:19:54" I have set the correct system time but no difference
I have tried a lot of wireless options and some of the timezones but i did not solve the problem
I have a new ASA 5510 running 8.3(1) and ASDM 6.4(5)
I am trying to use the real time log viewer to troubleshoot some access issues, but I am getting delays of up to 30 seconds or more between my client connecting to the ASA and the corresponding events showing in the RT Log viewer. I am using a simple filter for source IP as it's quite a busy device.
I've seen an article that says to turn off certain logging IDs (such as 304001 from memory) which I have done, but no different.
I have Windows XP Pro SP3. After a random period of maybe 30 mins to a few hours, my internet connection seems inexistant. PC reacts like there is no internet cable plugged in. I've checked the ipconfig command in command prompt before my internet shuts down and after and there was a change. A few lines(IPs) were missing after my internet fell.
View 9 Replies View Relatedwe have installed an evaluation version of Cisco Works LMS 4.0.1. Now we have purchased a license, but the evaluation period is over and I can't start the application anymore. Is there any possibility to install the license file after the evaluation period?
View 2 Replies View RelatedI have a new Win 7 Dell Precision Workstation that will not log in to my domain. I get an error that there is no login server available if I attempt to log in using a domain account. I log in as the local admin and then try to join a domain using the Join a Domain or Workgroup wizard. I then get an error stating "this operation returned because the timeout period expired". I have had to reset my core switch to get a couple of the new boxes (including this one) to even join the domain. I also show no internet in the Network and Sharing Center most of the time.
View 2 Replies View RelatedMy XP Pro SP3 PC is connected to a Netgear DG834N modem/router via Ethernet. If the PC is left for say 4-5 hours the ability to connect to websites disappears. The browser just hangs and it's the same with IE and Firefox The odd thing is I can still ping websites by domain name without trouble. So the interenet connection is actually still in place.The problem is consistent and repeatable.Throughout this I have a second XP Pro SP3 PC also connected to the router via Ethernet and it works perfectly.
View 2 Replies View RelatedI have a question about managing the Access Point:
-WLC2504
-AIR-LAP1262N-A-K9
First: I need the access point works by period, example: 08:00AM - 06:00PM after that disable the radio and return work next day at 08:00AM
Second: Also, if the radio no activity for a long period (e.g 60 or 120 minutes), disable the radio interface.It's possible with the WLC? Or maybe need implement one NCS?EnergyWise Technology - but, I only need "shutdown" the radio not the Access Point completely.
I'm using ASA 5510 and I wondered if we can configure reporting to know the traffic on each interface,the attacks,the vpn connection during a period ( 1 week or 1 month). For the moment, we can see these logs only in 'real time' .
View 1 Replies View RelatedI have a D610 Laptop with integrated Bluetooth and Wifi. The evaluation period has expired. Please obtain a license for this version of Bluetooth Stack for Windows by Toshiba."
I had called Gold Support last week and was asked to download/install the driver from the support downloads site and then download/install the patch as well. The bluetooth manager does not come up when this popup shows.
I have 4 computers (3 laptops, 1 desktop) in a shared office. We get internet access using their wireless network. All works fine. However, I need to share a printer amongst all of the computers. The printer is LAN enabled and I would normally just put all the PCs on a hub, together with the printer and share it that way. BUT my question is can we access the internet using the wireless network and the printer using a separate wired network at the same time?
View 7 Replies View RelatedRegion : India
Model : TD-W8151N
Hardware Version : Not Clear
Firmware Version :
ISP : MTNL
my ADSL light doesn't get on during my afternoon hours...after so many try too it get switch on after somewhat 5-6pm...
Just replaced a WRT54GS with an E2500. It seems that anytime a connected device goes "idle" for a while, the connection breaks or severely reduces and it's nearly impossible to get the connection back without performing an action at the device in question. Let the wireless connection on my laptop go unused for some period and it reduces to 1Mbps and you can't get back on by just using the link more... you have to do a "repair".
Let more than a few minutes pass since you've printed something on the wireless printer and you MUST go to the printer to re-establish the connection by turning the antenna off and then on again.Basically the same problem with my blueray/DVD getting on the network. When I shut the screen off on my phone, the wifi dies and receives NOTHING over that link while the screen is off.
None of these behaviors existed with the WRT... just the 2500. Background/facts - current firmware, DHCP with reservations, WPA2/per, MAC filtering in use, UPnP disabled. MTU/Beacon/Frag threshold/RTS threshold set per recommendations on this site.
we have a customer with a ASA 5510 with a CSC module in it. The device tells us the Base license has expired. The new license has been renewed - after - the grace period. The Trendmicro site tells us the Base license is valid until 21 october 2013 but the CSC refuses to acknowledge this. The module is able to fetch updates form the Internet so it does not look like a connection problem to me (it also has a plus license which is also valid till far into 2013 and that one works).Is it possible that the current license key is "dead" and the CSC expects a new license key because the grace period was expired?
View 1 Replies View RelatedI got this error this operation returned because the timeout period expired error code 0x000005b4
View 1 Replies View RelatedI have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
View 3 Replies View Related