my environment: IE-3000-8TC industry-switch ios: ies-ipservicesk9-mz.150-2.SE2
if i do
vlan 12 name NextVLAN state active
in putty, everything is ok. but if i set this lines in a config-file and use them by config net or copy tftp: running-config, then this commands are completely ignored.how to setup VLAN so that this are funktional. i dont need a "interface vlan xx"! in addition manually configured vlan are shown in show vlan command but there are no entries inside a sh running-config output even i user show running-config all.
We have a VPN 3000 that we use to connect. We are recieving reports that some of the users are connected but after a set period of time they are disconnected. Is there any changes that I could look at in the VPN 3000 that could point me in the right direction.
I have a Cisco 2911 router with 4 T1 connections. Two are set as a multilink and the other two are for two other locations. The router will run fine, but after a month I cannot ping the gigabit ethernet 0/0 interface. I would have to manually reboot the router to get it to respond again. Before I noticed a lot of interface discards which would shutdown the 2911 and a manual reboot would be needed, but for this time it isn't the case. Where would I start with this the memory and cpu usage are fine.
Here is the config: Current configuration : 2905 bytes ! version 15.0
Every other day and sometimes everyday I have an issue where my network slows down in one area at around the same time of day 12:00pm. I am using Solarwinds and I don't see anything significant showing up.
So, I just upgraded my mobo/cpu (Z77A-G45 and i5-2500k) and I'm having an issue with my connection as it seems to drop every 5 to 15 minutes constantly and have no idea what exactly is wrongThe kicker is my old mobo did the same thing and I had to do something in win7 to fix it (not sure if it was the drivers or what) but I just can't remember what exactly.
I have just bought an E3000 router when my old router died last week. I am having two problems:
1. The data rate slows down after a period of time (long message trail elsewhere)
2. I cannot see everything on the network.
I have several Win 7 computers, two win xp computers, three NAS devices (linux based), and a printer sitting on the network, along with two switches to cope with all the traffic (not to mention iPods, iphones etc.)With my old router, I couold see everything plugged into the network from my main Win 7 computer. (note: the win 7 network map does not always work, but the windows explorer window of the network always showed everything).With the E3000 router, I can only see 1 or 2 of the devices on the network. If I reboot the router, then sometimes all of the devices appear on the windows explorer window (sometimes not)I am running a workgroup (not a domain) and i am not using win 7's homegroup because that will not work with the non-win 7 devices.Is there a setting that will see all of the devices in Win 7 (either on the router or on the computers). I suspect it is a router issue as it worked with my old Zyxel router.
I have cisco 3845 router and 4507 & 2960 switch. I have 4 Vlans on 4507 and connected to router on four ports. Its working fine. Now i want to create another vlan ( vlan 15 ) that trunk with vlan 20 and router port f0/0/1. i.e router F 0/0/1 ports belongs only two vlan(15,20) and need to intervlan routing. My conf. given below.
Switch conf:
interface GigabitEthernet3/1 description ## to router## switchport trunk encapsulation dot1q
I've bought a "WAG160N v1.0 Annex A" almost 2 years ago. I never used it's wireless feature untill we moved our house. Now it's like 4 month I'm using its wifi feature and I've got to admit I'm really frustrated by its functionality!
For months the modem just dropped wireless connection constantly in various time periods. Somtimes it went like 2 days without any problem but some other times I had to change channel every 15 minutes for it to get back working. And yes it didn't get fix until I changed the channel, otherwise clients had to wait several hours for a 50/50 chance of reconnection. Now It's two days the changing channel trick no longer works. I tried all channels and even put my notebook next to the modem but no luck. The notebook sometimes connnects to the access point but disconnects after a few seconds. Somtimes it doesnt even detect the SSID of my WAG160N modem. Some friends suggested that the wireless hardware of my modem is broken and no longer works but I'm eager to know if it is broken why is it still broadcasting and sending signal.
I've tried everything from upgrading and downgrading firmware to turning on and off the modem several times and changes modem position. And even tried the G-only 20MHz mode.We are at a very crowdy place. Using inSSIDer I could pick about 15 other access points. Only few of them are using Wireless-N, most of them are using Wireless-G.This is the inSSIDer diagram of my WAG160N modem from a client: [code]
I am trying to implement RBSCP on two 3845s running 15.1(4)M1 Adv Enterprise over a satellite link. The "show" commands all look correct, but whenever I policy route my machine through the RBSCP tunnel I dont even make it to the opposite side. However, if I remove the "tunnel mode RBSCP" command so it acts like a regular GRE tunnel, I route through it just fine. So I know its not a NAT, routing issue. [code]
I need very Urgent Time based Bandwidth limit on subinterface in Cisco 3845 Router.At Present 3Mb input/output rate-limit of our one of the client now they need between 9:00 to 20:59 3 Mb and between 21:00 to 8:59 they need 9 Mb bandwidth, please see current b/w limit config of our client in my router subinterface.
I have a 3845-Mb that has a username and password already on it. This needs to be wiped as its a sold unit. However i cannot break into teh IOS in Hyperterminal using Ctrl-Break either as it boots or after teh IOS image has loaded (after it shows Decompressed image {ok} etc). I have tried several break key combinations such as ctrl+F6+break and they dont work either. On boot the unit does show Password recovery Functionality is disabled. IOS image is 12.4(13r)T.
When I try to add an IP address to a port-channel interface on a 3845 ISR I am getting an error that seems to imply that only L2 etherchanneling is possible. Am I missing something?Cisco IOS Software, 3800 Software (C3845-ADVIPSERVICESK9-M), Version 12.4(24)T8,
sfo-c3845-1#sho run int port-channel 1 Building configuration... Current configuration : 31 bytes ! interface Port-channel1 end
We have a Cisco 3845 router configured as a voice gateway with multi SIP trunks. But when it reachs 200 calls traffic, the CPU increase to 60-70% and caused by CCSIP_SPI_CONTROL process.
CPU utilization for five seconds: 46%/30%; one minute: 54%; five minutes: 58% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 377 400729448 171017979 2343 6.31% 10.71% 12.44% 0 CCSIP_SPI_CONTRO
Can the encryption module (DES/ 3DES/AES/SSL VPN Encrytion/compression) for Cisco Router 3845 able to support the external connection from other high end router, for example cisco 7200? What is the maximum bandwidth, load and concurrent connection it can support?
I found cpu load around 90 - 100% on cisco 3845, so I show tech-spec and show log on router and found process "Virtual Exec" use high load. I'm not sure this situation make high latency time on my network.
We have a number of 3845 routers, some running IOS 12.4(22)T2 and earlier and some running 12.4(24)T4. On the ones with 12.4(22)T2 and earlier, gigabit interface g0/1 shows interface down/line protocol down when there is no cable connected to the interface and the interface is not in shutdown state. On the ones with 12.4(24)T4, gigabit interface g0/1 shows interface up/line protocol down when there is no cable connected to the interface and the interface is not in shutdown state. Interestingly in both cases, the "show controller g0/1" command shows " network link is down (NO CARRIER)" when there is no cable attached. It makes sense to us that the interface status would be down/down when there is no cable attached. It does not makes sense to us that the interace would be up/down. Did Cisco at some point change their philosophy on whether an interface should show down/down or up/down when there is no cable attached, or is this a bug?
I have a router 3845 with c3845-advsecurityk9-mz.124-24.T6.bin software . Frequently we are facing problem in logging to the device .Inorder to resolve we need to reboot the router . Yesterday fortunately i have got the console access for some time so i came to know that TPLUS process is consuming 99.9% percentage cpu.
I have installed NM-1T3/E3 IN A CISCO 3845 WITH IOS c3845-advipservicesk9-mz.124-9.T3.bin AND 512 MB RAM .WHEN I ENABLE THE CARD THE CPU PROC HISTORY SHOWS 100% WHEN DISABLED IT COMES DOWN TO 10%
Slot 0: C3845 Mother board 1GE(TX,SFP),1GE(TX), integrated VPN and 4W Port adapter, 7 ports Port adapter is analyzed Slot 2: NM-1T3/E3 (clear/subrate) Port adapter, 1 port Port adapter is analyzed
I change only a chasis in a router 3845, but the "show version" command should be the same , except for the serial number and other parameter of time.. however, the number of serial interface change from 4 up to 2.The hardware module of 3845 are 3.
1.- VWIC E1/T1 with 2 port 2.- Fastethernet 36 port 3.- Supervisor engine with 2 Gigabit port
I realize what the error message says but I was not aware that there is a class-map limit? This is on a ISR 3845 router.Is there a limit on the amount of class maps that can be configured on the router?
Is it the amount of times class maps are used (as I do not think my client has 1023 class maps but they are used several times each)?
I have a cisco router 3845 with Etherswitch modules and one Vlan configured "172.16.6/24", many switch ports are assigned to this vlan. i would like to translate one IP address 172.16.6.200 to a new one "172.25.42.10" but need to keep the other IPs from "172.16.6/24" without changes. below is the configuration of vlan interface and switch port. [code]
I have a Cisco 3845 Integrated Service Router and I have installed a Service Module. I want to use the integrated Gigabit ports as switch ports and put ports in the Service Module and Gigabit port in a VLAN.
Is this possible? can it be done by setting internal Gigabit link as trunk and how? Below is the somewhat the setup i am looking for
Service module fa0/1 | fa0/2 | Vlan X fa0/3 | [Code]....
I'm trying to have a standard equipment for our POP deployment. Basically this edge router will connect to our customers and pass data and or voice traffic, capable of BGP and good enough to accomodate up to 4 clients.
We have on hand a 3845 Router, and ME3600X. The 3845 is EOS and replacement is 3945. The ME3600X is a fixed configuration so would you recommend a 3945 or a much higher model like a 7300.
I have cisco router 3845 with cisco switch. internet is not work or some time it works but very slow on LAN, i have web server on my LAN but internet users can access it very well. it seems like there is some outgoing traffic issue
interface GigabitEthernet0/0.7 encapsulation dot1Q 7 ip address 192.168.7.1 255.255.255.0 ip helper-address 192.168.10.15
In my cisco 3845 router I can see output packet drop in some of the interfaces.I suspect that router is processing packet beyond its mix throughput limit. Moreover when i run show int fax/y switching command I can see packet drop by RP process.
I am looking into bringing MetroE into our data center. I currently have a 3845 router and would like to find out if it can support a 300-500M MetrE link.
Also would you recommend a router or a switch that can handle 300M - 500M MetroE link ? Do you typically terminate MetroE link on a router or a switch ? can I terminate it directly to a routed port on a Nexus 7K ?
I have this card installed onmy 3845 running version 12.4(18). But this card fails to show up.
here is what I found in a show tech.
WIC Slot 0: Unknown WAN daughter card WIC module not supported/disabled in this slot Hardware Revision : 2.0 Top Assy. Part Number : 800-27738-02 Part Number : 73-10677-02 Board Revision : B0 Deviation Number : 0 Fab Version : 02 PCB Serial Number : FOC******** RMA Test History : 00 RMA Number : 0-0-0-0 RMA History : 00 Product (FRU) Number : HWIC-2FE Version Identifier : V01 CLEI Code : COUIAFUCAA Base MAC Address : 001a.6c70.260b MAC Address block size : 2 Connector Type : 01 EEPROM format version 4 EEPROM contents (hex):(code)
I was wondering what this command that appears in default configuration of cisco routers: scheduler max-task-time 5000.I did some research in forums but did not find anything apart from the "scheduler" command with other options.
I am using ASA5500 series box which has a site to site tunnel terminated on it.Is there any command by which we can check the up time of the tunnel.
ASA# sh isakmp sa Active SA: 1 Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)Total IKE SA: 1 1 IKE Peer: x.x.x.x Type : L2L Role : responder Rekey : no State : MM_ACTIVE
