Cisco Switching/Routing :: 3845 Can't Break Into IOS
Apr 24, 2012
I have a 3845-Mb that has a username and password already on it. This needs to be wiped as its a sold unit. However i cannot break into teh IOS in Hyperterminal using Ctrl-Break either as it boots or after teh IOS image has loaded (after it shows Decompressed image {ok} etc). I have tried several break key combinations such as ctrl+F6+break and they dont work either. On boot the unit does show Password recovery Functionality is disabled. IOS image is 12.4(13r)T.
View 6 Replies
ADVERTISEMENT
Jul 24, 2012
I have Cisco ASA 5510 series router which was handling by our one of our network admin who left without giving admin password. Now this is time to break the password . Since i don't know the admin password of the router , i don't how to handle few request. I am not a basically network admin guy to handle such things but i need to know how to break the password in order to do further requests. How to login router admin console without password or any chance to bring into default factory configuration.?
View 1 Replies
View Related
Aug 15, 2012
we have the following setup for our network :
UserNetwork - ASA5550 - WAN Router 2911 - ISP Netowrk - Branch Routers 877s / 1941s
Since last week we started noticing this problem that the branch users started to complain of slow application response.. After verifying it with the ISP and middle network we noticed that if i ping from my machine (ie usernetwork) to the WAN Router interface (facing the ASA) , i get time outs.. which is strange cause this is directly connected to it via ethernet cable.
View 5 Replies
View Related
Jun 9, 2013
When I try to add an IP address to a port-channel interface on a 3845 ISR I am getting an error that seems to imply that only L2 etherchanneling is possible. Am I missing something?Cisco IOS Software, 3800 Software (C3845-ADVIPSERVICESK9-M), Version 12.4(24)T8,
sfo-c3845-1#sho run int port-channel 1
Building configuration...
Current configuration : 31 bytes
!
interface Port-channel1
end
[code].....
View 3 Replies
View Related
Mar 28, 2013
We have a Cisco 3845 router configured as a voice gateway with multi SIP trunks. But when it reachs 200 calls traffic, the CPU increase to 60-70% and caused by CCSIP_SPI_CONTROL process.
CPU utilization for five seconds: 46%/30%; one minute: 54%; five minutes: 58%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
377 400729448 171017979 2343 6.31% 10.71% 12.44% 0 CCSIP_SPI_CONTRO
[Code].....
View 2 Replies
View Related
Jun 25, 2012
Can the encryption module (DES/ 3DES/AES/SSL VPN Encrytion/compression) for Cisco Router 3845 able to support the external connection from other high end router, for example cisco 7200? What is the maximum bandwidth, load and concurrent connection it can support?
View 1 Replies
View Related
Mar 7, 2013
I found cpu load around 90 - 100% on cisco 3845, so I show tech-spec and show log on router and found process "Virtual Exec" use high load. I'm not sure this situation make high latency time on my network.
View 3 Replies
View Related
Oct 26, 2011
We have a number of 3845 routers, some running IOS 12.4(22)T2 and earlier and some running 12.4(24)T4. On the ones with 12.4(22)T2 and earlier, gigabit interface g0/1 shows interface down/line protocol down when there is no cable connected to the interface and the interface is not in shutdown state. On the ones with 12.4(24)T4, gigabit interface g0/1 shows interface up/line protocol down when there is no cable connected to the interface and the interface is not in shutdown state. Interestingly in both cases, the "show controller g0/1" command shows " network link is down (NO CARRIER)" when there is no cable attached. It makes sense to us that the interface status would be down/down when there is no cable attached. It does not makes sense to us that the interace would be up/down. Did Cisco at some point change their philosophy on whether an interface should show down/down or up/down when there is no cable attached, or is this a bug?
View 1 Replies
View Related
Nov 29, 2011
I have a router 3845 with c3845-advsecurityk9-mz.124-24.T6.bin software . Frequently we are facing problem in logging to the device .Inorder to resolve we need to reboot the router . Yesterday fortunately i have got the console access for some time so i came to know that TPLUS process is consuming 99.9% percentage cpu.
View 1 Replies
View Related
Jun 21, 2010
I have installed NM-1T3/E3 IN A CISCO 3845 WITH IOS c3845-advipservicesk9-mz.124-9.T3.bin AND 512 MB RAM .WHEN I ENABLE THE CARD THE CPU PROC HISTORY SHOWS 100% WHEN DISABLED IT COMES DOWN TO 10%
Slot 0: C3845 Mother board 1GE(TX,SFP),1GE(TX), integrated VPN and 4W Port adapter, 7 ports Port adapter is analyzed
Slot 2: NM-1T3/E3 (clear/subrate) Port adapter, 1 port Port adapter is analyzed
View 6 Replies
View Related
Mar 25, 2012
I change only a chasis in a router 3845, but the "show version" command should be the same , except for the serial number and other parameter of time.. however, the number of serial interface change from 4 up to 2.The hardware module of 3845 are 3.
1.- VWIC E1/T1 with 2 port
2.- Fastethernet 36 port
3.- Supervisor engine with 2 Gigabit port
View 7 Replies
View Related
Apr 17, 2012
I realize what the error message says but I was not aware that there is a class-map limit? This is on a ISR 3845 router.Is there a limit on the amount of class maps that can be configured on the router?
Is it the amount of times class maps are used (as I do not think my client has 1023 class maps but they are used several times each)?
View 3 Replies
View Related
Nov 20, 2011
I have a cisco router 3845 with Etherswitch modules and one Vlan configured "172.16.6/24", many switch ports are assigned to this vlan. i would like to translate one IP address 172.16.6.200 to a new one "172.25.42.10" but need to keep the other IPs from "172.16.6/24" without changes. below is the configuration of vlan interface and switch port. [code]
View 8 Replies
View Related
Jan 30, 2012
I have a Cisco 3845 Integrated Service Router and I have installed a Service Module. I want to use the integrated Gigabit ports as switch ports and put ports in the Service Module and Gigabit port in a VLAN.
Is this possible? can it be done by setting internal Gigabit link as trunk and how? Below is the somewhat the setup i am looking for
Service module
fa0/1 |
fa0/2 | Vlan X
fa0/3 |
[Code]....
View 7 Replies
View Related
Mar 18, 2013
I'm trying to have a standard equipment for our POP deployment. Basically this edge router will connect to our customers and pass data and or voice traffic, capable of BGP and good enough to accomodate up to 4 clients.
We have on hand a 3845 Router, and ME3600X. The 3845 is EOS and replacement is 3945. The ME3600X is a fixed configuration so would you recommend a 3945 or a much higher model like a 7300.
View 0 Replies
View Related
Nov 7, 2011
I have a 3845 router which got reloaded immediately and need to know the reason for the reload .Router have created crash info detail .
View 3 Replies
View Related
Nov 27, 2011
In my cisco 3845 router I can see output packet drop in some of the interfaces.I suspect that router is processing packet beyond its mix throughput limit. Moreover when i run show int fax/y switching command I can see packet drop by RP process.
View 11 Replies
View Related
Feb 21, 2012
I am looking into bringing MetroE into our data center. I currently have a 3845 router and would like to find out if it can support a 300-500M MetrE link.
Also would you recommend a router or a switch that can handle 300M - 500M MetroE link ? Do you typically terminate MetroE link on a router or a switch ? can I terminate it directly to a routed port on a Nexus 7K ?
View 8 Replies
View Related
Jan 16, 2008
I have this card installed onmy 3845 running version 12.4(18). But this card fails to show up.
here is what I found in a show tech.
WIC Slot 0:
Unknown WAN daughter card
WIC module not supported/disabled in this slot
Hardware Revision : 2.0
Top Assy. Part Number : 800-27738-02
Part Number : 73-10677-02
Board Revision : B0
Deviation Number : 0
Fab Version : 02
PCB Serial Number : FOC********
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : HWIC-2FE
Version Identifier : V01
CLEI Code : COUIAFUCAA
Base MAC Address : 001a.6c70.260b
MAC Address block size : 2
Connector Type : 01
EEPROM format version 4
EEPROM contents (hex):(code)
View 4 Replies
View Related
Aug 27, 2007
We have a customer that is relocating thier headquarters. They have a temporary requirement to bridge multiple vlans or a router T3 link to the new location as they cannot change the IP subnets. Setup is 3560 switch connecting to a 3845 then T3 to remote 3845 and 3560. I need to bridge multiple VLANs. I have seen a good example on how to do it over sonet but I don't see how to translate that to an HDLC or Frame Relay encapsulation for the T3 Link.
View 5 Replies
View Related
Dec 28, 2011
I have two routers at our core data center, a 3845 and a 3640. These are configured with GLBP. There are 4 remote sites:
Site #1: One T1 link to the 3825
Site #2: One T1 link to the 3825, and One T1 link to the 3640
Site #3: One T1 link to the 3825, and One T1 link to the 3640
Site #4: One fractional T1 link to the 3825, and One T1 link to the 3640.
My question regards site #4. If i understand correctly, GLBP works on the premise of "host" balancing, and not true "load" balancing. The reason I ask is that the large majority of our WAN traffic is from our Exchange server to our remote sites. In the case of site #4, our exchange server is sending traffic on the fractional T1. Is there any way with GLBP to either split this traffic from a particular host across two links in a round-robin fashion, but leave other hosts to travel wherever the router sends them, or, to force at least our exchange server to use the full T1, rather than the fractional?
I've read up on the weighting mechanism, and it appears that tracking an interface has nothing to do with bandwidth use. If I understand correctly, if I were to track the Site #4 PPP to the 3640, and give a weight of 10 to glbp on there, it would really only take affect if the interface is down. It will have nothing to do with host AVF election.For the record, exchange traffic is constant to this site, so there is no chance for the host connection to reset and potentially elect to use the larger pipe. I would like to "tweak" this to make better use of available bandwidth.
View 2 Replies
View Related
Feb 14, 2012
I am trying to configure two 3845 routers to act as dhcp server and dhcp relay. Clients are connected to the router that relays all dhcp requests to the vrf instance which is used to connect it to the router wich is running dhcp server.
Router1
ip vrf dhcp_dns
rd 8:1
int gi0/0
ip vrf forwarding dhcp_dns
ip address 192.168.200.5 255.255.255.248
[code]...
So far I can see dhcp requests coming from the R1 and dhcp server on R2 replies with the dhcp offer but PC is not getting any ip.
View 8 Replies
View Related
May 21, 2013
I have NM-16ESW card installed in one of my 3845 router. Below is the sh inventory output
NAME: "16 Port 10BaseT/100BaseTX EtherSwitch", DESCR: "16 Port 10BaseT/100BaseTX EtherSwitch"
PID: NM-16ESW , VID: V01 , SN: FOC11482484
NAME: "Gigabit(1000BaseT) module for EtherSwitch NM", DESCR: "Gigabit(1000BaseT) module for EtherSwitch NM"
PID: GE-DCARD-ESW , VID: V01 , SN: FOC11454FW6
Is the Gig port available here can be used for uplink?I found following comment at
[URL]...
"GE-DCARD-ESW: This optional 1000BaseT Gigabit Ethernet port for NM-16ESW and NMD-36-ESW can be used for a gigabit connection for a file server or for intra-chassis stacking of the Cisco EtherSwitch module. Stacking is supported in Cisco IOS release 12.2(11)T and beyond"
View 1 Replies
View Related
Oct 14, 2012
I have a Cisco 3845 with the archive command configured:
archive
path tftp://x.x.x.x/$h
write-memory
time-period 60
The archive command works with the execution of the write mem, but with the "time-period" doesn't work.This is the show version of my 3845:
NTP_Server#SH VER
Cisco IOS Software, 3800 Software (C3845-SPSERVICESK9-M), Version 12.3(14)T7, RELEASE SOFTWARE (fc2)
Technical Support: [URL]
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Thu 23-Mar-06 01:59 by pwade
[code].....
View 1 Replies
View Related
Nov 16, 2011
I have a 3845 router. Setup SSH Version 2generated rsa keys (1024)set login localtransport input ssh and telnet is enabled since I can't get ssh connection working When I connect using SSH, I get the following error. server refused authentication protocol.
View 21 Replies
View Related
Jan 19, 2012
I am having Cisco 3845 series router with c3900-universalk9-mz.SPA.151-4.M2.bin IOS . I want to install new Licence on it for DATA. When i am trying to install licence on it i am facing the error "% Error: License installation failed with error: XML parsing failed".
View 4 Replies
View Related
Dec 10, 2012
Is there any physical or technical diferrences between PWR-3845 AC/2 and PWR-3845 AC? We are trying to order replacement parts and wondering if PWR-3845 AC is for one power supply and AC/2 means you get two with one order?
View 1 Replies
View Related
Dec 7, 2012
Is there any physical or technical diferrences between PWR-3845 AC/2 and PWR-3845 AC? We are trying to order replacement parts and if PWR-3845 AC is for one power supply and AC/2 means you get two with one order.
View 1 Replies
View Related
Mar 24, 2011
some of the websities like facebook are blocked
View 2 Replies
View Related
Jun 28, 2012
My facebook site is blocked by firewall . how can i open it ?
View 1 Replies
View Related
Jun 16, 2010
i have cisco 1941 router.unfortunately i dont remember password.Can any body tell me how to break password.I tried to go in Rom mon using ctr+break but nothing is happened.
View 5 Replies
View Related
Mar 6, 2011
We have installed a SRST in one of our remote offices. They have ISDN Primary, and we have a 6mb MPLS link to our main HQ with 400k of QoS on the line. During the day, both Internal calls over the MPLS and external calls over the ISDN break up, but it doesnt happen all the time, i.e in a day the morning will be ok, then the users experience the break ups in the afternoon, then its everything is ok again.
The only factor that the calls share is the Lan infrastructure i.e the 3750G switches (7) of them which are stacked.We did have MAC flapping errors, and our telecoms provider suggested that it maybe these causing the issues, however we have got rid of all MAC flap errors, and are still receiving voice break ups.
Because the Lan switches are the only "item" both calls share, I am wondering now if the setup of the switches is correct. [code]
View 1 Replies
View Related
May 8, 2011
I have over 20 units doing the same thing and it seems to be a software isssue but i dont see any bugs or posts on it. This is only on 2960S switches and not 2960 or 2960G units.
If i use the password reset feature to break the units into rom and then type "boot" instead of power cycling the unit, they will fail MBIST post tests. If the unit is power cycled or left to boot normally on its own, there is no issues and all post tests pass. I know MBIST is Memory Built In Self Test and was thinking maybe breaking the unit into rom disrupts those memory tests for some reason. I tried the following software and got the same results with all of the images:
122-55.SE2
122-55.SE
122-53.SE2
122-53.SE1
Logs attached are from the same switch, one with password reset procedure used and while left to boot on its own.
View 11 Replies
View Related
