I realize what the error message says but I was not aware that there is a class-map limit? This is on a ISR 3845 router.Is there a limit on the amount of class maps that can be configured on the router?
Is it the amount of times class maps are used (as I do not think my client has 1023 class maps but they are used several times each)?
I have a 3845-Mb that has a username and password already on it. This needs to be wiped as its a sold unit. However i cannot break into teh IOS in Hyperterminal using Ctrl-Break either as it boots or after teh IOS image has loaded (after it shows Decompressed image {ok} etc). I have tried several break key combinations such as ctrl+F6+break and they dont work either. On boot the unit does show Password recovery Functionality is disabled. IOS image is 12.4(13r)T.
View 6 Replies View RelatedWhen I try to add an IP address to a port-channel interface on a 3845 ISR I am getting an error that seems to imply that only L2 etherchanneling is possible. Am I missing something?Cisco IOS Software, 3800 Software (C3845-ADVIPSERVICESK9-M), Version 12.4(24)T8,
sfo-c3845-1#sho run int port-channel 1
Building configuration...
Current configuration : 31 bytes
!
interface Port-channel1
end
[code].....
We have a Cisco 3845 router configured as a voice gateway with multi SIP trunks. But when it reachs 200 calls traffic, the CPU increase to 60-70% and caused by CCSIP_SPI_CONTROL process.
CPU utilization for five seconds: 46%/30%; one minute: 54%; five minutes: 58%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
377 400729448 171017979 2343 6.31% 10.71% 12.44% 0 CCSIP_SPI_CONTRO
[Code].....
Can the encryption module (DES/ 3DES/AES/SSL VPN Encrytion/compression) for Cisco Router 3845 able to support the external connection from other high end router, for example cisco 7200? What is the maximum bandwidth, load and concurrent connection it can support?
View 1 Replies View RelatedI found cpu load around 90 - 100% on cisco 3845, so I show tech-spec and show log on router and found process "Virtual Exec" use high load. I'm not sure this situation make high latency time on my network.
View 3 Replies View RelatedWe have a number of 3845 routers, some running IOS 12.4(22)T2 and earlier and some running 12.4(24)T4. On the ones with 12.4(22)T2 and earlier, gigabit interface g0/1 shows interface down/line protocol down when there is no cable connected to the interface and the interface is not in shutdown state. On the ones with 12.4(24)T4, gigabit interface g0/1 shows interface up/line protocol down when there is no cable connected to the interface and the interface is not in shutdown state. Interestingly in both cases, the "show controller g0/1" command shows " network link is down (NO CARRIER)" when there is no cable attached. It makes sense to us that the interface status would be down/down when there is no cable attached. It does not makes sense to us that the interace would be up/down. Did Cisco at some point change their philosophy on whether an interface should show down/down or up/down when there is no cable attached, or is this a bug?
View 1 Replies View RelatedI have a router 3845 with c3845-advsecurityk9-mz.124-24.T6.bin software . Frequently we are facing problem in logging to the device .Inorder to resolve we need to reboot the router . Yesterday fortunately i have got the console access for some time so i came to know that TPLUS process is consuming 99.9% percentage cpu.
View 1 Replies View RelatedI have installed NM-1T3/E3 IN A CISCO 3845 WITH IOS c3845-advipservicesk9-mz.124-9.T3.bin AND 512 MB RAM .WHEN I ENABLE THE CARD THE CPU PROC HISTORY SHOWS 100% WHEN DISABLED IT COMES DOWN TO 10%
Slot 0: C3845 Mother board 1GE(TX,SFP),1GE(TX), integrated VPN and 4W Port adapter, 7 ports Port adapter is analyzed
Slot 2: NM-1T3/E3 (clear/subrate) Port adapter, 1 port Port adapter is analyzed
I change only a chasis in a router 3845, but the "show version" command should be the same , except for the serial number and other parameter of time.. however, the number of serial interface change from 4 up to 2.The hardware module of 3845 are 3.
1.- VWIC E1/T1 with 2 port
2.- Fastethernet 36 port
3.- Supervisor engine with 2 Gigabit port
I have a cisco router 3845 with Etherswitch modules and one Vlan configured "172.16.6/24", many switch ports are assigned to this vlan. i would like to translate one IP address 172.16.6.200 to a new one "172.25.42.10" but need to keep the other IPs from "172.16.6/24" without changes. below is the configuration of vlan interface and switch port. [code]
View 8 Replies View RelatedI have a Cisco 3845 Integrated Service Router and I have installed a Service Module. I want to use the integrated Gigabit ports as switch ports and put ports in the Service Module and Gigabit port in a VLAN.
Is this possible? can it be done by setting internal Gigabit link as trunk and how? Below is the somewhat the setup i am looking for
Service module
fa0/1 |
fa0/2 | Vlan X
fa0/3 |
[Code]....
I'm trying to have a standard equipment for our POP deployment. Basically this edge router will connect to our customers and pass data and or voice traffic, capable of BGP and good enough to accomodate up to 4 clients.
We have on hand a 3845 Router, and ME3600X. The 3845 is EOS and replacement is 3945. The ME3600X is a fixed configuration so would you recommend a 3945 or a much higher model like a 7300.
I have a 3845 router which got reloaded immediately and need to know the reason for the reload .Router have created crash info detail .
View 3 Replies View RelatedIn my cisco 3845 router I can see output packet drop in some of the interfaces.I suspect that router is processing packet beyond its mix throughput limit. Moreover when i run show int fax/y switching command I can see packet drop by RP process.
View 11 Replies View RelatedI am looking into bringing MetroE into our data center. I currently have a 3845 router and would like to find out if it can support a 300-500M MetrE link.
Also would you recommend a router or a switch that can handle 300M - 500M MetroE link ? Do you typically terminate MetroE link on a router or a switch ? can I terminate it directly to a routed port on a Nexus 7K ?
I have this card installed onmy 3845 running version 12.4(18). But this card fails to show up.
here is what I found in a show tech.
WIC Slot 0:
Unknown WAN daughter card
WIC module not supported/disabled in this slot
Hardware Revision : 2.0
Top Assy. Part Number : 800-27738-02
Part Number : 73-10677-02
Board Revision : B0
Deviation Number : 0
Fab Version : 02
PCB Serial Number : FOC********
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : HWIC-2FE
Version Identifier : V01
CLEI Code : COUIAFUCAA
Base MAC Address : 001a.6c70.260b
MAC Address block size : 2
Connector Type : 01
EEPROM format version 4
EEPROM contents (hex):(code)
We have a customer that is relocating thier headquarters. They have a temporary requirement to bridge multiple vlans or a router T3 link to the new location as they cannot change the IP subnets. Setup is 3560 switch connecting to a 3845 then T3 to remote 3845 and 3560. I need to bridge multiple VLANs. I have seen a good example on how to do it over sonet but I don't see how to translate that to an HDLC or Frame Relay encapsulation for the T3 Link.
View 5 Replies View RelatedI have two routers at our core data center, a 3845 and a 3640. These are configured with GLBP. There are 4 remote sites:
Site #1: One T1 link to the 3825
Site #2: One T1 link to the 3825, and One T1 link to the 3640
Site #3: One T1 link to the 3825, and One T1 link to the 3640
Site #4: One fractional T1 link to the 3825, and One T1 link to the 3640.
My question regards site #4. If i understand correctly, GLBP works on the premise of "host" balancing, and not true "load" balancing. The reason I ask is that the large majority of our WAN traffic is from our Exchange server to our remote sites. In the case of site #4, our exchange server is sending traffic on the fractional T1. Is there any way with GLBP to either split this traffic from a particular host across two links in a round-robin fashion, but leave other hosts to travel wherever the router sends them, or, to force at least our exchange server to use the full T1, rather than the fractional?
I've read up on the weighting mechanism, and it appears that tracking an interface has nothing to do with bandwidth use. If I understand correctly, if I were to track the Site #4 PPP to the 3640, and give a weight of 10 to glbp on there, it would really only take affect if the interface is down. It will have nothing to do with host AVF election.For the record, exchange traffic is constant to this site, so there is no chance for the host connection to reset and potentially elect to use the larger pipe. I would like to "tweak" this to make better use of available bandwidth.
I am trying to configure two 3845 routers to act as dhcp server and dhcp relay. Clients are connected to the router that relays all dhcp requests to the vrf instance which is used to connect it to the router wich is running dhcp server.
Router1
ip vrf dhcp_dns
rd 8:1
int gi0/0
ip vrf forwarding dhcp_dns
ip address 192.168.200.5 255.255.255.248
[code]...
So far I can see dhcp requests coming from the R1 and dhcp server on R2 replies with the dhcp offer but PC is not getting any ip.
I have NM-16ESW card installed in one of my 3845 router. Below is the sh inventory output
NAME: "16 Port 10BaseT/100BaseTX EtherSwitch", DESCR: "16 Port 10BaseT/100BaseTX EtherSwitch"
PID: NM-16ESW , VID: V01 , SN: FOC11482484
NAME: "Gigabit(1000BaseT) module for EtherSwitch NM", DESCR: "Gigabit(1000BaseT) module for EtherSwitch NM"
PID: GE-DCARD-ESW , VID: V01 , SN: FOC11454FW6
Is the Gig port available here can be used for uplink?I found following comment at
[URL]...
"GE-DCARD-ESW: This optional 1000BaseT Gigabit Ethernet port for NM-16ESW and NMD-36-ESW can be used for a gigabit connection for a file server or for intra-chassis stacking of the Cisco EtherSwitch module. Stacking is supported in Cisco IOS release 12.2(11)T and beyond"
I have a Cisco 3845 with the archive command configured:
archive
path tftp://x.x.x.x/$h
write-memory
time-period 60
The archive command works with the execution of the write mem, but with the "time-period" doesn't work.This is the show version of my 3845:
NTP_Server#SH VER
Cisco IOS Software, 3800 Software (C3845-SPSERVICESK9-M), Version 12.3(14)T7, RELEASE SOFTWARE (fc2)
Technical Support: [URL]
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Thu 23-Mar-06 01:59 by pwade
[code].....
Using 'debug ip packet acl# det on a 2911. On an older Cisco router you could set up an ACL
access-list 150 permit tcp any any eq 1023 and then run debug ip packet 151 det and this would give a good debug output for any traffic matching a TCP port of 1023.Now when I try this on a 29xx ( Version 15.1(4)M3 ) I get the screen filling with a lot of multicats HSRP communications.
I have tried rewriting the acl to have other deny statements after the permit to limit the source or destination hosts and/or the ports but the HSRP data is still there.
like this
access-list 150 permit tcp any any eq 1023
access-list 150 deny udp any any eq 1985(code)
I have a 3845 router. Setup SSH Version 2generated rsa keys (1024)set login localtransport input ssh and telnet is enabled since I can't get ssh connection working When I connect using SSH, I get the following error. server refused authentication protocol.
View 21 Replies View RelatedI have an ASA firewall and I have never configured an FTP server for a large scale network (well large in my opinion). I want to ensure we have the highest level of security available for the FTP and to limit only the specific users designated by an ACL. Would SFTP be the best available option for security measures? Should I only use Passive FTP and what range of ports above 1023 should I open for only 1 or 2 FTP clients at a time? Also if I use Passive mode do I need to use protocol inspection for FTP?Also, Currently I'm unsure of what files need to be accessed on our network but should the SFTP Server always only be installed within the DMZ?
View 4 Replies View RelatedI am having Cisco 3845 series router with c3900-universalk9-mz.SPA.151-4.M2.bin IOS . I want to install new Licence on it for DATA. When i am trying to install licence on it i am facing the error "% Error: License installation failed with error: XML parsing failed".
View 4 Replies View RelatedIs there any physical or technical diferrences between PWR-3845 AC/2 and PWR-3845 AC? We are trying to order replacement parts and wondering if PWR-3845 AC is for one power supply and AC/2 means you get two with one order?
View 1 Replies View RelatedIs there any physical or technical diferrences between PWR-3845 AC/2 and PWR-3845 AC? We are trying to order replacement parts and if PWR-3845 AC is for one power supply and AC/2 means you get two with one order.
View 1 Replies View RelatedI'am a novice with LMS 4.0.I create 4 device group in Group Management, I restarted my server and since this reboot, I haven't any device in my groups. I would like to use the archive synchronization but I can't see my device in my groups.
View 6 Replies View RelatedI have seen some discussion in the forums regarding user defined groups being empty in LMS 4.0 but not 4.1. I am having this issue in 4.1. Under User Defined groups, I have created 2 logical groups named "Physical Location" and "Switches". These do not contain any actual devices, they are just containers for other groups. Under the Physical Location logical group I have created 2 other groups, Acuna and Hampton. Under the Switches group I have also created 2 groups, HDM and HHC. The criterion for the Physical Location group is based on the first 3 characters of the hostname:
Device.System.Name startswith "hdm"
The criterion for the Switches group is based on the value of a user defined field, Admin_responsibility:
Device.Admin_responsibility equals "HDM"
The Physical Location groups work - the Switches group does not. Both the HDM and the HHC group should contain several devices. The HDM group contains 2, the HHC contains none. If I edit the groups and click "next" until I get to step 3, Membership: Edit, the "objects matching criteria" list is fully populated - it contains the devices that it should contain. However, after I click "Finish" and go to Inventory => Add / Import / Manage Devices there is no change in group membership - the HDM group contains 2 devices and the HHC group contains none.
I configured an ip pool on VPN 3000 concetnrator. i wanted to an attribute to use on the nework access profile on the acs 5.3. i was advised to use pool name. However, we don't have pool name attribute on VPN concentrator. only, IP range and subnet mask. how do i refer an IP pool on VPN concentrator in ACS5.3? is there another attribute I can use on ACS5.3 to invoke a pool on CVPN3000, like ip range...?
View 2 Replies View RelatedI am trying to configure the dashboards for the pre-defined roles ie) Network Operator, Network Administrator, Helpdesk, etc but I cannot find the document to do this. I am running LMS version 4.1.
The goal is to create users and put them in one of these roles and then they would inherit these dashboards when they log on. Can this be done on LMS ? The doco that I am reading says that each user needs to configure their own dashboard or they can use the public dashboard as a starting point.
I have a VPN connection to my office network. The VPN connection appears to work fine as it connects and logs me in successfully. In the connection box I have to provide a domain and my username to log in. Once the VPN is connected I am then able to ping my office computer as if I was on the same network. That is great. The problem is that there is a server on that network that defines a bunch of A records for web applications we are working on and I can't seem to hit any of those from my home computer, even though I can at work. If I remote into the office PC and navigate to these addresses they work fine. I also know that my co-worker can hit these a records from home so it has to be something I'm doing wrong.
[Code]....