I'am a novice with LMS 4.0.I create 4 device group in Group Management, I restarted my server and since this reboot, I haven't any device in my groups. I would like to use the archive synchronization but I can't see my device in my groups.
View 6 Replies
I have seen some discussion in the forums regarding user defined groups being empty in LMS 4.0 but not 4.1. I am having this issue in 4.1. Under User Defined groups, I have created 2 logical groups named "Physical Location" and "Switches". These do not contain any actual devices, they are just containers for other groups. Under the Physical Location logical group I have created 2 other groups, Acuna and Hampton. Under the Switches group I have also created 2 groups, HDM and HHC. The criterion for the Physical Location group is based on the first 3 characters of the hostname:
Device.System.Name startswith "hdm"
The criterion for the Switches group is based on the value of a user defined field, Admin_responsibility:
Device.Admin_responsibility equals "HDM"
The Physical Location groups work - the Switches group does not. Both the HDM and the HHC group should contain several devices. The HDM group contains 2, the HHC contains none. If I edit the groups and click "next" until I get to step 3, Membership: Edit, the "objects matching criteria" list is fully populated - it contains the devices that it should contain. However, after I click "Finish" and go to Inventory => Add / Import / Manage Devices there is no change in group membership - the HDM group contains 2 devices and the HHC group contains none.
I´m looking for the best configuration to restrict a user to read-only. The restriction should be configured via CLI not TACACS+.
-Hardware: 3750 (probably not interesting for this question)
-Oldest IOS: 12.2(53)SE1
The user should be allowed to: see the running-configurationtrigger all kinds of show-commandsping and traceroute from the device.The user should not be allowed to: upload/delete/rename files on the flash-memoryget into level 15 (not sure if I can avoid this)all other commands despite those from level 1 and those specified above.
I make qos on VPN Tunnel, but i make command service-policy output name, it show the error below Traffic Shaping feature is not supported in user defined class of parent level policy.My cisco router 1921, IOS : c1900-universalk9-mz.SPA.150-1.M5.bin
View 1 Replies View RelatedI created some User Defined Groups in LMS 4.1, now I want to apply certain fault notification groups to Event Sets.
Unfortunately the Groups I configured are not in the Group Selector of the Fault Notification Group: Admin > Network > Notification and Action Settings > Fault Notification Group
I have two tunnel groups using WEBVPN , I have local users at ASA 5510 version 7.2.
How can I authenticate one user in only one group?Now with local users I can loggin in both tunnel groups
We are using ACS 4.2.1.15 with patch 8 on ACS 1113 SE box.
Our requirement is to assign ACS loal group to user on basis of windows Nt group. Which means I dont wants to create individual users in ACS rather when user will login, the auth request will be forwarded to AD(remote database). Depeneding on the remote database group the user should be mapped to local database.
For this I have configured "database group mapping" according to following cisco guide. [URL]
However when ever my AD users are authenticating they are getting the membership of default group as configured in "Default" profile. I am using TACACS+ protocol in my routers and switches for authentication.
whether "Group mapping by External user database" works with TACACS+ or only with RADIUS protocol. If it works with TACACS+ what else configuration need to be done so that my ACS can map users to proper groups instead of default group.
I would like to ask some question about VPN clinet and SSL VPN, on my ASA 5510 i have many tunnel-group it have around 5 tunnel-group and i have one SSL VPN,i also have user 20 user. let me show you that:
1- tunnel-group Staff-VPN remote-access
2- tunnel-group Manager-VPN remote-access
3- tunnel-group normalstaff-VPN remote-access
4- tunnel-group guest-VPN remote-access
5- tunnel-group other-VPN remote-access
and tunnel-group sslgroup type remote-access
and i have user around 20 user and i want to specific user to tunnel-groups like this
1- tunnel-group Staff-VPN remote-access
username AAA password AAA
username AAA01 password AA01
2- tunnel-group Manager-VPN remote-access
username BBB password BBB
username BBB01 password BBB01
3- tunnel-group normalstaff-VPN remote-access
username CCC password CCC
username CCC01 password CCC01
5- tunnel-group other-VPN remote-access
username DDD password DDD
username DDD01 password DDD01
So, How can i manag tunel-groups with user?
I need to block the multimedia streaming to a certain group of users accessing my wireless connection.I'm using squid as my proxy server and the users are registered on a LDAP database. A RADIUS server provides authentication.
View 1 Replies View RelatedI just started configuring AnyConnect with ASA 5520 that uses Cisco SecureACS to pass radius authentication. I configured two profiles with different split tunnel restrictions and what I discovered is that when the client connects to the ASA, they are provided a choice of these two groups (I guess there is no way to restrict this) and I can log into either one with any user account. How do I restrict this so that the user can only use one profile? Currently users capable of VPN would be placed in one specific AD group so that is what SecureACS checks. Is there a sample configuration guide to handle multiple profiles with different levels of access?
View 3 Replies View Relatedhaving LMS 4.0.1 is it possible to authenticate user on a group base and assign different privilege to different groups?. The user's group are available in the LDAP server.Do I have to use a TACACS/RADIUS server between the Ciscoworks LMS and the LDAP repository?
View 1 Replies View RelatedThis question might actually belong under tacacs server but it's only happening with the ACE. I've configured tacacs on the 4710 and configured the tacacs server per the documentation. If I enter the shell:<context>*Admin default-domain under the group settings when I login with my tacacs ID my role is set to Network-Monitor. If I set the shell in my specific tacacs ID I'm assigned the correct role as Admin. We're running ACS ver 4.1 and the ACE is A4(1.1)
View 1 Replies View RelatedWe are migrating our ACS 5.1 to ISE 1.0.4.
- On ACS we were doing 802.1x Authentification over an Activedirectory, assigning Vlan according to computer/user group. In some case the user vlan could be different from the computer vlan (ex admin account connecting to a user account). This works great with ACS.I tested the same function with ISE and the behaviour is a bit different :
- When the computer boot, I can see the computer account being authenticated on ISE. The logs show the AD groups the computer belongs to and the Authorization profile is well applied according to the AD group.
- When the user login, I can see the user account being authenticated on ISE, BUT the logs show the AD groups of the previous authentication, the one belonging to the computer not the user. So the authorization profile is the one from the computer not the user.
It seems that the AD group attributes are not well updated :
- AD logs show the second authentication doesn't engage a new group parsing from AD
- Shutting down the switch port when user is logged engage a new authentication a AD group are well updated.
- Bug toolkit reference the same bug but for WLC CSCto83897 so I suspect it's present in other case.
Why is it that when SNMPv3 user "TestV3-User" was added to my SNMPv3 implementation on my 6506 switch, the group/MD5/Emcryption settings are missing for this user (See "sh snmp user" output)???
router#sh snmp user
User name: TestV3-User
Engine ID: 80000009030000249706EFC0
storage-type: nonvolatile active access-list: test
[Code]....
I have a Cisco ASA 5505 that I've setup with an SSL VPN. This is for personal use, and I therefore don't have need for anything more than local authentication. [code]
I'd like to have one profile/policy where I only encrypt data going to my split-tunnel ACL, and I'd like to have one profile/policy where I encrypt all traffic.
The issue ive been fighting is - it doesn't seem like its possible to associate more than one group policy per user. If it IS possible - can you tell me how I associate both groups to my local account?
I just configure VPN for end users in PIX515e with IOS 8 and get stuck with "Tunnel Rejected: User (msveden) not member of group (VPN-shared), group-lock check failed.". tell me how I add user to my VPN group?
View 1 Replies View RelatedWe want to set up a wireless user group in our town between a few friends and new people who are interested to join. As far as I heard I don't need a ICASA License for the 5.8GHz Frequency if we are using it for a non profit orginization, so we may use that.
1 x Routerboard
3 x Radio Plugin Boards
3 x 120degree Antennas
to set up a 360degree HS (Highsite).Then at each person's house we will need:
1 x Routerboard
1 x Radio Plugin Board
1 x Whichever Antenna
Is that correct? Then also if we wanto run VoIP on our network, how do I do that? Basicly we want to use it for gaming, file sharing and VoIP. No Internet of anything else.
My question is on ASA and ACS5.2 users.Have my ASA SSL VPN and IPSEC VPN, the my ACS5.2 many users, for example, wireless user.I would now like to establish an independent user group, only the VPN user name and password, while both the ASA VPN can only allow users in this independent group of ACS5.2 VPN login, how to configure?
View 1 Replies View RelatedWe have several ASA 5510 firewalls which are being used as VPN gateways.RSA SecurID is the authentication mechanism using native SDI connectivity. No ACS server is being used.Is it possible to assign user Group and other attributes (such as ACL), using the SecurID RADIUS server? I know this is what the Cisco ACS is for, but is it possible using the RSA RADIUS server itself?
View 11 Replies View RelatedI'm running a Windows Server 2008 Enterprise Edition server that is currently the domain controller, and a Windows 7 Ultimate client. I have a 'Test' user for messing around with group policy - anyway, on the client Start Menu it has 'Test User' which leads to some form of libraries folder. Is it possible to restrict the link without removing their name?
View 3 Replies View RelatedCan I use AAA Radius on a ASA 5505 to block outgoing user access by user name in a group?
View 2 Replies View RelatedI just got the WRT610N and I really like it so far, I'm playing with the NAS option and I can't get it to create any new users or groups. I click on the link, fill out the form and click on 'modify user' (The set-up guide has a button there for 'save settings') and nothing gets created. I tried this several times and there are no new groups or users. I checked the storage.info file and there is no additional users or groups there either. I think I can edit that file but I'm not too sure what these last 2 lines mean
nas_login@admin:admin:admin: off guest:guest:guest: onusers_content@admin:admin:admin:admin: off guest:guest:guest:guest: on
I try to map LDAP Group to ASA Group policy following documentation:
[URL]
This is a config for ASA 8.0. I would have expected it to work on 8.4 as well but I do run into problems. The mapping as shown in LDAP Debug and ASA Log will actually happen but it is overwritten by the "GPnoAccess" Group Policy configured locally in the Tunnel Group. From earlier works with RADIUS I would have expected the user specific Attribute to be "stronger"?
ASA Log:
AAA retrieved user specific group policy (correct Policy) for user = XXX
AAA retrieved default group policy (GPnoAccess) for user = XXX
I configured an ip pool on VPN 3000 concetnrator. i wanted to an attribute to use on the nework access profile on the acs 5.3. i was advised to use pool name. However, we don't have pool name attribute on VPN concentrator. only, IP range and subnet mask. how do i refer an IP pool on VPN concentrator in ACS5.3? is there another attribute I can use on ACS5.3 to invoke a pool on CVPN3000, like ip range...?
View 2 Replies View RelatedI am trying to configure the dashboards for the pre-defined roles ie) Network Operator, Network Administrator, Helpdesk, etc but I cannot find the document to do this. I am running LMS version 4.1.
The goal is to create users and put them in one of these roles and then they would inherit these dashboards when they log on. Can this be done on LMS ? The doco that I am reading says that each user needs to configure their own dashboard or they can use the public dashboard as a starting point.
I realize what the error message says but I was not aware that there is a class-map limit? This is on a ISR 3845 router.Is there a limit on the amount of class maps that can be configured on the router?
Is it the amount of times class maps are used (as I do not think my client has 1023 class maps but they are used several times each)?
I have a VPN connection to my office network. The VPN connection appears to work fine as it connects and logs me in successfully. In the connection box I have to provide a domain and my username to log in. Once the VPN is connected I am then able to ping my office computer as if I was on the same network. That is great. The problem is that there is a server on that network that defines a bunch of A records for web applications we are working on and I can't seem to hit any of those from my home computer, even though I can at work. If I remote into the office PC and navigate to these addresses they work fine. I also know that my co-worker can hit these a records from home so it has to be something I'm doing wrong.
[Code]....
i have configured SSL VPN on Cisco ASA5510 which is working fine .My Users connected the VPN and access the servers remotely. But now i face one challange my users use PPTP VPN of the customer now a days configured at the Customer Network. When they Connect the PPTP VPN unable to Access the servers remotely defined on the SSL VPN Route.
View 1 Replies View RelatedI'm using a Cisco Wireless LAN Controller 5508, 14x Access Points 1041 and 6x Access Points 1031 in combination with a NCS 1.0.
Is it possible to broadcast SSID'S only on defined Access Points, e.g. AP 1-3,7-10,18? If yes, what have I to do?
We are running ACS 5.2 patch 6 and want to restrict access for users to be able to add devices to the system.For example, admin person in site A can only add devices into the site A group and cannot see/access other sites groups.
View 1 Replies View RelatedWe are using an ASA 5510 and remote access (SSL VPN) using the AnyConnect client.
Is it possible to display a user message when a user connects using the AnyConnect client, matching a specific dynamic access policy? Can the message be displayed when the action is "Continue" rather than "Terminate"? I can't seem to get this to work and wondered if there was a LUA function to do this.
We have a DAP which gives a restricted ACL when the user's anti-virus is out of date, and I wanted to notify the user to update their anti-virus and reconnect.
I want to create a local user in my Cisco ASA 5520 to allow the user to use the ASDM in Read-Only mode. I want the user to view the Dashboard only.
View 1 Replies View RelatedIs it configurable to allow wifi user to user traffic on WLC 5508?
View 4 Replies View Related
