Cisco :: 7925 Silence Hole On Wi-Fi
Mar 5, 2013
I have an issue with the 7925 phones. We have a Cisco Call Manager with a couple of access points and a wireless lan controller. But we have at some points some sort of hole in the sound. He doesn't loose it's connection because i don't hear the beep when he's out of range. And according to the phone he still has a connection with the access point. But there is no sound anymore. And if i walk a couple of meters further i got sound again. If i walk back i somehow get in the same hole and loose the sound. Further back in i got sound back.
I know when it comes to WiFi that there can be some sort of blind spot but there isn't. He still has it's connection with the AP. Is there a value regarding de RSSI value that he needs to have to get a normal speech?
View 9 Replies
ADVERTISEMENT
Apr 18, 2012
Having some issues with a vpn between two of my locations. Both edge devices are ASA's, and the tunnel is an IPSEC tunnel. Both MTU's are set to 1500 both on inside and outside. (provider mtu setting request is 1514, and both ASA's will be changed out soon.) Unfortunately, some exchange/kerberos auth issues are causing me a problem in the remote site. I perform the tests that microsoft recommends using a length of 1472 on packet ping size, and do not fragment flag (1406 is the largest packet I can push across the vpn) . I know part of this is due to the extra overhead that ipsec places on the connection.
I want to refrain from putting the black hole registry workaround on all of the PC's in this remote location.I've also seen some discussion about manually setting the TCPMSS value down to 1300 on most ASA's.
View 1 Replies
View Related
Aug 17, 2011
My mechanical engineer needs detailed measurements for the hole patterns on the sides of the Cisco 2911. Where I could find this?
I've searched and read the installation docs, which shows pictures of the units. Although useful, they does not show exact measurements, angles, and hole diameters.
View 2 Replies
View Related
Dec 29, 2011
[URL]I have a Linksys E4200, even if i put wireless on manual WPS is still working, any answer from Linksys?
View 5 Replies
View Related
Jul 24, 2011
I'm currently in the process of the setting up a new wireless network and I want to test out our 7925 phones on it. When I try uploading the certificate to the phone it fails and I find the following error in the trace logs
[code]...
I created this certificate using using Windows Server 2003 and it is 2048 bits. This certificate works fine with my laptop but I'm unable to upload it to the phone. The app load currently on the phone is CP7925-MFG-D.8.LOADS. Are there any specific guidelines out there when creating a certificate for a Cisco 7925 phone?
View 2 Replies
View Related
Mar 9, 2013
have configured Cisco IPPhone 7925G with EAP-TLS setting. (With manufacture installed and Userinstalled certificate). My issue is while roaming from 1 AccessPoint to another AccessPoint the call getting droped. I need to restart the IPPhone to reauthentiate again. In ACS am agging the authentication time-out error. (I had changed the time out value for EAP-TLS to 20 in WLC as per recommendation.)
If am using static web key there is no issue in roaming.
What is the reommended setting inorder for the EAP-TLS to work properly.
View 2 Replies
View Related
Jun 4, 2013
Using Sha1 for Cisco 7925g and sha256 for data. Two separate CA's, one EnTrust (SHA1) the other Local Wondows CA (SHA256); ISE can only use one at a time to process a particular protocol (ie..EAP-TLS, HTTP, etc...) As a result we have to have a separate PSN just for Wireless and Wired VoIP (which can only hold SHA1 RSA1024).
View 5 Replies
View Related
May 22, 2013
We have a problem when I call bettween two 7925 in same SSID, VLAN voice. They cannot hear each other. The SSID and LAPs are in Flexconnet. From desk phones there are no problem and betwen one deskphone and one wireless phone there no problem too.
View 2 Replies
View Related
Mar 14, 2012
I have a customer that have trouble with the update of the position of a client. Even if the clients walks across the whole building, the client will stay at the same place for several minutes. Is there any way to tune the refresh rate? When I push the load button in the map, the clients position will refresh, or it did when I was on the site, now they just test with an application.
The setup:
WiSM 7.0.220
WCS 7.0.220
MSE 7.0.220
They use the API for MSE to get the location information to the external application, and that will show the information on a cisco 7925 IP phone.know a way to increasing the refresh rate?
View 3 Replies
View Related
Jun 25, 2012
recently we have deployed a Two APs in branch office warehouse and I have one wifi phone 7925 used over there. the problem is every time when phone roaming from one AP to another, 2 or 3 packets dropped, following is result of the 'debug client ':
--More or (q)uit current module or <ctrl-z> to abort*apfMsConnTask_7: Jun 27 09:52:25.496: 88:43:e1:4f:ab:39 Association received from mobile on AP a0:cf:5b:c3:a8:90*apfMsConnTask_7: Jun 27 09:52:25.497: 88:43:e1:4f:ab:39 10.107.38.121 RUN (20) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1621)*apfMsConnTask_7: Jun 27 09:52:25.497: 88:43:e1:4f:ab:39 Applying site-specific IPv6 override for station 88:43:e1:4f:ab:39 - vapId 14, site 'AKL-AP-GP', interface 'management'*apfMsConnTask_7: Jun 27 09:52:25.497: 88:43:e1:4f:ab:39 Applying IPv6 Interface Policy for station 88:43:e1:4f:ab:39 - vlan 38, interface id 0, interface 'management'*apfMsConnTask_7: Jun 27 09:52:25.497: 88:43:e1:4f:ab:39
[code]....
View 6 Replies
View Related
Sep 19, 2010
How to get the FCC ID from a 7925 phone. We have one on order for an upcoming VoFi site survey but I wanted to take a look at the maximum output power by channel so I can begin cell/channel planning.
View 2 Replies
View Related
Jul 20, 2011
I'm trying to test fast roaming using a Cisco 2100 Series controller and 2 1140 APs. The initial authentication succeeds fine and the wireless connection works ok using WPA2+CCKM and LEAP with a Cisco ACS radius server.The problem is that the client does not attempt to preauthenticate with the other AP because the RSN Capabilities IE in the AP beacons and probe responses do not set the RSN Preauthentication capable bit. I can't figure out what it takes to get the APs to indicate to clients that it can do preauthentication. I'm been crawling through all the documentation I can find, to no avail.
View 1 Replies
View Related
Aug 22, 2011
We are about to share a 10 MBit ISP connection with 2 others companies, and they are going to split the bill up into 3,3 and 4 Mbit, so we where thinking that we could setup a switch before their and ours router and provide them with a static IP from our ISP. But is it possible to set a bandwidth limit on the ports of a Cisco Catalyst 2960-8TC, so that we can set a limit of 3,3 and 4 on 3 ports.
View 1 Replies
View Related
Dec 3, 2011
I want to PAT my project of WLAN and i attached the document, how I create the Testing Criteria of the said scenarios, PAT document includes WCS 7.0, WLC 5508, MSE 3310, Cisco AP 3502e and ACS 4.2.
View 0 Replies
View Related
Jul 12, 2012
I have cisco ASA5510 firewall using in my network but unable to bolck Url's unwanted. can i block the [URL] on the asa by using regular exp.
View 3 Replies
View Related
Mar 1, 2012
I have 7 POE switches that have ESI IP phones attached. I have two VLANS, 1 and 2. VLAN 2 is used for voice and is defined in each switch.The ESI IP phones connect to my POE switch ports and the pc attaches through the ESI IP phone.
I have had voice quality issue between floors in my building. Talking to others on my floor via the IP phone, there are no voice quality issues. [code]
View 1 Replies
View Related
Nov 18, 2012
is it possible to connect Cisco Ap-1242AG with non-cisco wireless router to work as repeater?
View 1 Replies
View Related
May 1, 2012
I am looking at a config on a 5550 FW, and am trying to make sense of the syntax of the following rules. I have been to the Cisco site, but can't find much on the syntax.
View 8 Replies
View Related
Mar 10, 2011
I currently use a device called the Access Enforcer which runs OpenBSD. I have 3 stable, working VPN tunnel's where the other side's device is a Cisco ASA 5520 or 5540. I was setting up my 4th VPN where the other side used a Cisco ASA 5520 and ran into issue's. The Cisco side can bring up the tunnel. Once the tunnel is up each side can talk to the other side. However, when the tunnel is dropped, the OpenBSD side cannot bring up the tunnel. The error received is on the OpenBSD device is "isakmpd[29581]: transport_send_messages: giving up on exchange from-XX.X.X.0/24-to-XX.XXX.XXX.240, no response from peer XX.XX.XXX.141:4500". I have been trying to figure this out for weeks now and can't seem to find the cause.
View 3 Replies
View Related
Dec 5, 2011
I am trying to configure a 3750G that has been sitting on the shelf for several months and am getting the following error -
% Error: Unable to create flash:/microcode_update% Error: It must not already exist
Normally, getting an error during POST isnt a good thing. My first thought was that flash was corrupted or flagged RO somehow. I did fsck flash: with no change. I next tried fsck /test flash:. It tested 77 blocks and performed 0 erasures. It had been running for about 15 minutes with no problems reported so far. Multiple reboots of the switch still report the same error.
I have reviewed the history of what I have done on this switch and finally think I found the problem. I noticed a microcode_update directory that I am not used to see on a 3750. Deleted the directory using the rmdir command and rebooted the switch. On reboot, I noticed that a front_end/ directory was listed as being created as well as fe_type_1 and fe_type_2 were created. The switch now boots up without any errors.
View 3 Replies
View Related
Jan 3, 2013
I have two Cisco Aironets 1401 connected to a Cisco Catalyst 3560 Switch. When users log onto the Wifi the APs authenticate with a Freeradius that then authenticates with LDAP.
Recently users have been getting kicked off of the network but I'm not sure why.If so how do I set these APs to roam with my setupd?For all I know there could be an issue with the switch I'm just not sure where to start when it comes to troubleshooting this issue.
View 17 Replies
View Related
Dec 29, 2012
Guys I am using a cisco 2911 router with three interfaces: Gi0/0 connected through a switch to all my servers and Gi0/2 which will connect to another server, and Gi0/1 is my outside interface connecting through a switch to two ISP's.I have webservers and Terminal servers/File Servers with 10.0.0.0 network address connected throught My Gi0/0 interface.Now I want to implement a Cisco Advanced firewall for security on my router using CCP.I want the firewall to work such that it allows external users to access the servers on Gi0/0 through ports 0,23,25,20,21,53, 110,3389. and to access the SIP server on Gi0/2. My issue is can i just create two DMZ's for both interface Gi0/0 and Gi0/2 without creating an inside zone and Gi0/1 as outside zone as my internal traffic is mostly server based and the users connect remotely through terminal server to access resourcess using RDP, secondly how do I open the relevant ports.I have checked alot and all I have seen is just basic process on using the wizard I have no idea how to go about this issue.
View 19 Replies
View Related
Mar 30, 2011
I bought a new cisco 3550 switch to prepare for my Cisco certification prepration. Actually i dont know how to connect the cisco switch to a laptop with only usb ports....... earlier i used to do my practise using Cisco packet tracer but i think for CCNP switch that is not enough thats y i bought second hand switch. how can i connect that switch with my toshiba laptop which has only USB ports. do i need to buy some sort of convertor or other hardware. And if so what does u call it and how much does it cost?
View 5 Replies
View Related
Apr 14, 2013
I am struggling to have my PPTP traffic to get routed through NAT to reach other Server LAN segment. I am using Cisco 2921 router as a PPTP server.This Cisco 2921 router is working as PPTP server and doing NAT also to reach Server LAN segment (LAN-B).My problem is after PPTP connection establishes I cannot reach any of the LAN segment, but after connecting PPTP I can browse Internet without any issue, but none of the LAN element is reachable. Please have a look on the configuration I am posting 2921 router configuration to suggest something, I have also attached the network setup for better understanding…Just to update Clients in LAN-A can access Internet as well as servers (LAN-B). [code]
View 2 Replies
View Related
Dec 8, 2011
I would like to know the IOS which supports :ACL Support for Filtering on TTL Value feature on my Cisco 7600 device. I check on cisco and found the Cisco 12.4T release but this software doesn't fit onto my chasis. which software should I upgrade to on my cisco 7600 to have this feature.
View 5 Replies
View Related
Feb 27, 2012
I have a cisco router I would like to reset the password for. Its the first password that is entered. for exampleUser access verificationPassword:I have changed the en password using this command:router(config)#enable secret cisco123 <---example password
View 5 Replies
View Related
Jul 19, 2012
I finally got the Site to Site Vpn from our corporate to remote site. Is there a way to connect a cisco phone over that network. Since both Voice Vlans are exempt from acl I would imagine all traffic is clear to go accross? and if so I just have to set the phone to our tftp/ccme. Will that work.
View 2 Replies
View Related
Nov 6, 2011
I want to create a user who only has access to "router>" prompt on the CLI. this user should not be able to do enable command and by no other means be able to go to global configuration mode. I know the command router(conf t)# username ABC privilege 1 password ABCPASS, but even with this command, this user gets privilege 15 access.
View 2 Replies
View Related
Dec 27, 2012
I have the CISCO 1800 and I have there the HWIC-2T. I have two questions.First is an easy one. I want to replace the HWIC-2T with HWIC-4T but the CISCO 1800 guide and the HWIC-4T guide says that they dont fit together but I inserted the HWIC-4T in to the CISCO 1800 it recognized him with all the 4 Smart Serial ports that it hase. The question is, how can I check if the CISCO 1800 supports the HWIC-4T?Second question is how can I configure one of the Smart Serials in the HWIC-2T/4T to comunicate with the X.25 Protocol? What I have now is at one end CISCO 1800 and at the other end CISCO 2800 and they are comunicating with each other throught one of the Smart Serials they have. I want to connect to each one of then an old pc that comunicate only with X.25 and I want this two computers to comunicate with each other throught those two routers.
View 2 Replies
View Related
Aug 8, 2012
We're currently evaluating Cisco Prime LMS 4.2.Something we've been trying to achieve for the past couple of days is to have LMS notify us when a Microsoft Host is Unreachable, and then to notify us once that alarm has cleared (the Microsoft Host is Reachable again).
We're at the point where the Microsoft Host was discovered, LMS incorrectly identified it as a Cisco Call Manager, so we changed it's identity to non-cisco device > microsoft host > microsoft host. LMS currently has the device listed as being in the 'Questioned' state. SNMP timeout has been set to 15 seconds, and the SNMP community is correct.
Being new to LMS Prime, and having not received any training on the product to this point, we turned to the admin guide, but we couldn't find anything that goes into detail for how to manage the notification for non-Cisco devices.
Is what we're trying to achieve possible with Cisco Prime LMS 4.2? We just want to be able to receive simple 'host unreachable' notifications for Microsoft servers, and the corresponding 'cleared' notifications once the server is back online.
View 2 Replies
View Related
Feb 13, 2013
I'm trying to understand CEF; I know it's used most commonly in layer 3 switches but that routers can also do it. The routers that support CEF must have special hardware I'm assuming? (Since CEF is layer 3 processes in ASICs) How can we check if a router is capable of CEF? Does anyone know a good link/graphic that shows how much faster CEF is than software-based layer 3 processes?
View 10 Replies
View Related
Aug 29, 2012
Basically, I have a network which has a LAN and a DMZ. I need to isolate a few servers and users from the LAN so I created a VLAN on the switch. I assigned it an IP address in a different subnet and assigned ports to the VLAN. Port forwarding is configured on the switch.For testing purposes, before this goes live, I connected a computer directly to one of the switch ports (ge4/5) and assigned it a static IP in that subnet, the gateway being the VLAN IP. I can ping the VLAN IP but I can’t ping the router or get to the Internet,I tried setting the gateway to the ASA VLAN interface (e0/1.4) with the same result.The 1st step is to get Internet access. The next step will be to allow access to the Exchange server on the LAN.There are many devices not shown on the diagram but the important ones are there.
View 12 Replies
View Related
Feb 18, 2013
Having a hard time getting Cisco phones to roam 'cleanly' in a Cisco unified wireless environment; Cisco 2504 controller with Cisco LAP1142n (lightweight) APs. The phone SSID is not broadcast and is using WEP encryption. The problem is that when the user is walking around the property, traversing from AP to AP in-call (external and internal calls), they notice the point at which the phone roams from AP to AP - it's literally two or three seconds of no sound and then the call resumes back again. Fast SSID change has been enabled, we've tried locking the SSID to 802.11a only, b only and g only but with only slightly better results when locked to B. We've lowered the client roaming threshold RSSI to -75dB from -80dB, this also yielded better results but still a couple of seconds gap exists. Cisco TAC came in on a Webex session earlier, changed a few QoS settings and advanced wireless settings on the controller, but to no avail. Wireless signal has been proven to not be an issue; several AIRMagnet PRO surveys have been carried out showing the signal throughout the property to meet the -67dB requirement.
View 8 Replies
View Related
