I've been using a Belkin 54g Universal Repeater for around a year and a half to extend my wireless connection around the house but recently it's stopped working completely. The red "Searching" light is flashing constantly and it doesn't register with my computer anymore. I've tried connecting it to my main router and to my computer via ethernet to no avail.
View 1 Repliesfacing issues with TP-Link TL-WA801ND while setting it up as a Universal repeater.The AP is a Linksys E3200..and I got the TP-Link to broaden my WiFi at home, I was successful in setting it up, however, after a day or two I get prompted to enter a "WPA2 Enterprise" username/password.I DID NOT setup WPA2 Enterprise, mine is WPA2 Personal...it's peculiar that it works for a bit then reverts to Enterprise.
View -1 Replies View RelatedThe setup: My main router is a Belkin N. It is the DHCP controller. I have another Belkin N router connected by CAT5/RJ45, and DHCP is turned off. Each router has a different SSID, and WPA2//AES/TKIP is the security. The purpose of the second router is to act as an access point and extend the wireless range. Now I need to extend it further, but without through wireless. I had a G bridge connected to the second Belkin, and it in turn connected to a third router which was G. This worked but was sporadic. I bought an Amped SR150 N repeater to replace the bridge and third router.The repeater will connect to the second router with no problem. It shows the IP of the main router as the gateway IP. The laptop that the repeater is connected to then received an IP from the main router. However, the laptop has no internet. It also will not go to the IP of the main router.I tested the repeater by connecting it to the main router. That works fine, and the laptop gets internet. I tested the second router capability by connecting the laptop to it through wireless. That works fine to, and the laptop can go to the home page of both the main and second router. When I put the repeater back into the mix, the laptop does the same tihng: It gets a new IP from the main router, but no internet, and it will not go to the homepage of the main router.
View 1 Replies View RelatedIs it possible to downgrade the 4900M IOS image from Universal 15.x image to non-Universal (possibly IP BASE) 12.x image.
View 1 Replies View RelatedCould not find on Belkin website, hyperlink came up with "oops' result. Basic instructions to hook this up to my TV.
View 1 Replies View RelatedI would like to know if my Universal Ranger Extender F5D7132 is compatible with a 24dbi antenna? What is it power level (mw)?
View 2 Replies View RelatedI just got UVERSE and they supplied a new router (or is it a gateway) and my F7D8301 is excess to me. Is there a way to configure the Belkin router as a repeater?
View 1 Replies View RelatedI use comcast as an ISP and bought a zoom router to replace their router. I now want to use my old working Belkin router model F5D8236-4 as a repeater. Meaning I will use it after the Zoom router, wired, to extend the wireless capability to the other side of my house. Does this make any sense?
View 1 Replies View RelatedCan the Surf N300 be used as a WiFi repeater? Can the Surf N300 be used as a WiFi Access Point?
View 1 Replies View Relatedi hooked up a netgear repeater to my belkin n450db router and it shows a good connection betw router and extender and between extender and device (laptop and tv) however only a lan connection - no internet.
View 1 Replies View RelatedI am having a bit of trouble. I have a Belkin router (this is irrelevant) across the house, which is extended by the Belkin wireless bridge/repeater in my bedroom. The device in my room boosts my WiFi signal for my MacBook and iPhone, and the LAN (ethernet) port on the back allows my Debian server to connect to the network and internet. I have a Linksys switch that I wish to use, for I have another computer that requires an ethernet connection. Here is what happened:Debian 1 is connected via ethernet, no problem.I shut it down, unplug cable. Run cable from bridge to switch's uplink.Plug another ethernet cable into port one on switch, run it to Debian 1.
View 1 Replies View Relatedi have beetel adsl2+router connected to my main computer through ethernet cable but its wifi signal is very low. its signal hardly reach the other end of my house where my bedroom is, and i want to surf on my laptop or mobile from my bedroom only so basically i want to extend my wifi range or boost the signal the thing is i have a belkin f7d1301 basic n150 wireless router, i want to know whether i can use it as range extender or any other thing to boost my signal.
View 7 Replies View RelatedI am trying to use f5d7230-4 v6000 to connect my TV and Playstation to my home WLAN, but cannot set up the router to receive the signal from the base station (FRITZ!Box). Is it possible at all to use f5d7230-4 v6000 for such function?
View 2 Replies View RelatedSo I just got an Asus RT-N10+ trying to repeat my Buffalo Airstation wireless signal (WPA2/PSK). I choose the repeater step in the quick setup, and the signal has full bars, but when I try to connect, it gets stuck at:
"Please wait, RT-N10+ is connecting to buffaloairstation..." and it stays like that indefinitely and after a while, the ASUS wireless connection disappears as it continues "connecting".
what do i need to setup in WAG120N to work with a Wireless Network repeater?
View 1 Replies View RelatedI recently bought a Cisco RE1000 wireless repeater to boost the wireless signal to my garage office. Since then the signal has been intermittent, fluctuating between strong and weak signals, sometimes dropping off completely. Today I finally uplugged it, and the signal strength seems the same, even steadier, though that could be just the way the wind is blowing today.
How do I know if I'm picking up the wireless or repeater signal? Could it be interfering with my basic signal? How do I know which signal I'm getting?
i'm having WAG320N Linksys by Cisco , connected & working properly i need to connect 2 WAP4410 N to the router through wireless ( not wired )
i've did the same SSID same security same everything tried all the possible settings but it's not working as a repeater i've read the blogs & found that some people talking about new beta firmware i've tried to find it out to try but i didnt find it any where
I recently made an old router into a repeater by using DD-WRT. It seems to be working fine if I use LAN, but I cannot get WLAN to function properly. When I go to add a virtual interface and all the proper info, I all of a sudden cannot connect to the Internet. More specifically it seems to not assign me an IP address.
View 1 Replies View RelatedI need universal lan driver for windows 7
View 3 Replies View RelatedI am attempting to upload some files to my school server will Filezilla. It worked the very first time I attempted to do this. A box popped up and read something like, " The key is unknown, this may not be the computer you think it is", there was a check box asking to approve this server and save the key. I ticked this box and everything was fine, it was connected. I disconnected from the server and went back an hour later to upload something and got this message when attempting to connect, "server has unexpectedly closed network connection", then, "unable to connect". I get it every single time I try to do this from home. However, I have been able to connect everywhere else but my house. I can connect with the same computer from my friends wireless at his house, and from the wireless at work, all from the same computer that will not connect at home. I have also tried different operating system, Ubuntu, and nothing same error message. I have reinstalled the program, and tried other programs,,nothing. I have also deleted that key in the registry, from the check box earlier. At home it does not have that pop up saying " the key is unknown" anymore, even after deleting the key. Yet it does from all the other locations. I do not check it from anywhere else from fear that this will happen everywhere and then I can use it at all. The only difference I can see in these situations is my router, as my friend uses the same ISP, and the same computer was used from each location.
View 9 Replies View RelatedMy roommate bought a Belkin F5D7234-4 V5 router at Walmart and it keeps dropping the internet. Our computers stay connected but the router keeps telling us that it's trying to connect to the internet again. The apartment wired connection is just fine. Right now I'm writing this and the stupid router is blinking at me... Our apartment complex provides internet so I don't have access to the modem, or even know if it's dsl or cable. I've checked the firmware and it's up to date. All the settings are factory pre sets.
View 19 Replies View Relatedcome to a bit of a block in the road on a network im building ,all is going well except i need to build a pseudowire to backup our primary L2 circuit, I labbed this with some 3745's but the kit we are using is the 1921, with the universal image how do i go about upgrading functionality to allow this [code]
View 4 Replies View RelatedDoes Cisco CleanAir 1602i (standalone model) support Universal Workgroup Bridge? I read the release notes 15.2 but I couldn't find it.
View 7 Replies View Relatedfind what feature set is supported on this IOS S45EUK9-33-1511SG The client requires Layer 3 functionality so do i need to apply any license with it or it will perform layer 3 routing (like rip, ospf, bgp, ipv6, ospfv3) ?
View 1 Replies View RelatedI have a 1242 Access Point as root and a 871W Router as a non-root bridge (Diagram attached). I have a laptop connected to Fa 0 of the 871W router.
* I am able to ping from the AP to the Router and vice versa
* I am also able to ping from the router to the laptop and vice versa
* But I am not able to ping from the laptop to the AP
All bridging commands seem to be fine. Even tried adding route commands, but none seem to work.Please find the configuration below:
Configuration on Root AP:
hostname ap
!
enable secret 5 XX
!
[Code]....
My belkin 54G was working few years now. Just hours ago, I try to connect my iphone 3GS with belkin wifi. I go to the 192.168.2.1 (on my laptop - wifi), MAC address filtering and enable it. After insert my iphone 3gs ip address i press OK.
Here's the nightmare begin, after minutes. My internet connection is not working both on my laptop (wifi working but not internet) and the PC facing problem on internet connection. i try login again 192.168.2.1, hoping can restore it but it fail to load the page.
how to restore it?
Below is the screenshot of what I did.
1. my ipconfig show new IP address, 169.254.242.229. i try using this address to access but fail to load.
2. ping 192.168.2.1 but unreachable.
3. detail of my network connection details.
4. set my TCP/IP properties
5. ipconfig manage to change it and ping working now.
6. to my disappointment, 192.168.2.1 still not working. can't enter it's web interface.
I have a Belkin F5D7050 USB Wireless G network card and it won't connect to windows xp. It tried using on Linux (ubuntu 10.04 live cd) and it works perfectly. But when I boot into windows, it doesn't. I have installed all the drivers and software I could find for it. But the programs for it don't open at all and for some reason i cant even configure it using windows "Connect to". (You know how usually you get the little wireless icon at the bottom of the screen and stuff)
View 7 Replies View Relatedtrying to setup universal wifi extender. Lights indicate system is on and connected to my computer. however wps and link rate lights are not on.
View 1 Replies View RelatedWhat is the difference between IP Base and Universal for 3750X switches?
View 2 Replies View Relatedwhether a Cisco Router 2911 would work on images other than universal image. This is the question raised by one of our customer. He has 2811 Router where-in he has configured T1/E1 configuration, terminated to Zyxel Modem and working fine. Now he wants to replace this 2811 router with 2911 router. Since the universal image in 2911 router is not working with the present configuration in 2811 router, he wants to know, what options are there for him to configure this in 2911.
View 2 Replies View RelatedContrary to the information contained in the link above, these two parts do not play well together. I purchased both and plugged them in and no go. It doesn't even light anything on the WAP. It worked fine when it was on its own 12V DC adapter but not plugged into this injector. What I don't understand is why Cisco doesn't just make a Universal power injector that is essentially a 1 port switch and is 802.3af or 802.3at compatible. Its maddening. It looks like I'm going to have to get an SD208P and waste 6 ports just to get one with the correct POE for the WAP4410.
View 2 Replies View RelatedI am using Belkin router for my laptop . Once I shut down my laptop suddenly the router stops working and hence if some one else is using the wi-fi network, he is loosing the connectivity. For that I have to restart the router everytime when ever I shut down my laptop.
View 1 Replies View RelatedMy Belkin Wifi router which was working fine earlier has stopped working now. It shows a red/orange light and nothing else ( it normally shows a green light ). The light doesn't blink or flash. As a consequence, my wifi devices aren't connecting to the internet, however i can connect via my pc normally through my modem. I have a iball Baton modem and the model number of my wifi router is F7D1301 V1.
View 4 Replies View Related