So I just got an Asus RT-N10+ trying to repeat my Buffalo Airstation wireless signal (WPA2/PSK). I choose the repeater step in the quick setup, and the signal has full bars, but when I try to connect, it gets stuck at:
"Please wait, RT-N10+ is connecting to buffaloairstation..." and it stays like that indefinitely and after a while, the ASUS wireless connection disappears as it continues "connecting".
I have the Asus RT-N12 and at my old apartment it was set as my router. I now have moved and have roommates who already have a router in use. I want to use the repeater function of this router but when I follow the instructions given by asus I hit a wall. They say to switch to repeater mode, plug it into a client on the network, and then launch quick installation setup by opening an internet browser. Unfortunately when I use a wired connection to the old router I cannot even navigate the internet because my computer is interpreting it as being hard wired to the router for my old network. is there a way to factory reset the monitor?
View 3 Replies View Relatedgoing to be setting up my cable modem and Asus RT-N66U router in my basement in the work room/laundry room. My townhouse is 3 stories tall so just in case I wanted to look at my options for a range extender or repeater.
View 1 Replies View RelatedASUS Notebook G60Vx Series
Windows 7 Home Premium 64-bit
Intel(R) WiFi Link 5100 AGN
A few days ago my internet suddenly stopped working. I plugged in the ethernet cord and everything worked fine. Checking the properties in the device manager showed the device was working properly, I also tried resetting it to make sure it was enabled but it did not work.
Upon troubleshooting, the "Windows Network Diagnostic" said the problems was that the Wireless adapter was not turned on. Using the switch on the front of the laptop as well as the function keys does nothing. Usually a graphic pops up showing if the WiFi is on or off, changinging transparent to show the WiFi is disabled. Now when I turn the switch on it always appears transparent, effectively going from off to off
So I know the computer reads both the function keys and the switch on the front but both methods never actually turns the adapter on. I just finished a system restore and nothing has changed
I had an old linksys router running DDWRT. I bought a new Asus RT-N16 and finally set it up. I had to just duplicate the settings by hand as you cannot back them up across different hardware models even though both are running DDWRT.
I hooked up the new router and everything was working great, until I decided to check one of my port forwards. Turns out its not working, I can't connect through my DynDNS assigned dns name. Assuming I configured something wrong, I compared the settings of the two routers. Nothing interesting, it is set up right.
From there I decided to just hook the old router up, assuming I overlooked something. So I mess around with all the cables, and then, to my surprise, IT STILL DIDN'T WORK.
A few points of interest:My Static IPS are set up right. My server has the proper IP My home IP did not change. DynDns has the right IP. I rebooted all the network equipment and server... just for the hell of it. I tried changing a port forward to point to my main PC and that failed too.
I've been using a Belkin 54g Universal Repeater for around a year and a half to extend my wireless connection around the house but recently it's stopped working completely. The red "Searching" light is flashing constantly and it doesn't register with my computer anymore. I've tried connecting it to my main router and to my computer via ethernet to no avail.
View 1 Replies View RelatedThe wireless adapter keeps saying unidentified network, I can connect from other computers and they are all working fine.
Edit: Forgot to mention its a ASUS wireless n-15 adapter, also the system is a Windows 7 64 bit. Also, has a ip address 169.x.x.x which i know means no internet connection.
The setup: My main router is a Belkin N. It is the DHCP controller. I have another Belkin N router connected by CAT5/RJ45, and DHCP is turned off. Each router has a different SSID, and WPA2//AES/TKIP is the security. The purpose of the second router is to act as an access point and extend the wireless range. Now I need to extend it further, but without through wireless. I had a G bridge connected to the second Belkin, and it in turn connected to a third router which was G. This worked but was sporadic. I bought an Amped SR150 N repeater to replace the bridge and third router.The repeater will connect to the second router with no problem. It shows the IP of the main router as the gateway IP. The laptop that the repeater is connected to then received an IP from the main router. However, the laptop has no internet. It also will not go to the IP of the main router.I tested the repeater by connecting it to the main router. That works fine, and the laptop gets internet. I tested the second router capability by connecting the laptop to it through wireless. That works fine to, and the laptop can go to the home page of both the main and second router. When I put the repeater back into the mix, the laptop does the same tihng: It gets a new IP from the main router, but no internet, and it will not go to the homepage of the main router.
View 1 Replies View Relatedwhat do i need to setup in WAG120N to work with a Wireless Network repeater?
View 1 Replies View RelatedI recently bought a Cisco RE1000 wireless repeater to boost the wireless signal to my garage office. Since then the signal has been intermittent, fluctuating between strong and weak signals, sometimes dropping off completely. Today I finally uplugged it, and the signal strength seems the same, even steadier, though that could be just the way the wind is blowing today.
How do I know if I'm picking up the wireless or repeater signal? Could it be interfering with my basic signal? How do I know which signal I'm getting?
i'm having WAG320N Linksys by Cisco , connected & working properly i need to connect 2 WAP4410 N to the router through wireless ( not wired )
i've did the same SSID same security same everything tried all the possible settings but it's not working as a repeater i've read the blogs & found that some people talking about new beta firmware i've tried to find it out to try but i didnt find it any where
I have an ASUS X58C laptop which has been working OK to the internet via the ethernet cable but it has stopped working.I used the laptop via the wireless connection to access the internet while away from home and on my return I can not connect via the ethernet but I can connect OK via wireless. The results with the wireless enabled are :
C:>ipconfig
Windows IP Configuration
Ethernet adapter Local Area Connection* 13:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
[code]....
I can see that the ethernet adapter(s) are shown as media disconnected but I don't understand how to make them connected. I also don't understand why there are two ethernet adapters or what the Tunnel Adapters are.Before I did the ipconfig command I went into Control Panel/Device Manager/Network Adapters/SiS Ethernet Controller, right clicked and selected the Update Driver Software which searched the internet for a driver and installed it.
I have the Asus P5QL-VM DO motherboard.On the Ethernet port the lights are not working and I can not get an internet connection.
View 1 Replies View Relatedi use an asus k50c laptop which i connect to internet through a lan cable.i used to send ad-hoc connection to my other laptop for internet connection which was running fine until i upgraded my sys to the win7.the connection is no longer through and whenever it is the web browsers cant open any page.i ve tried everything i can.it shows that the there is connection but its not working.
View 19 Replies View RelatedJust purchased an N66U router and loving it so far. The only problem I'm having is that iTunes is not seeing the shared library I setup on the router. I have a usb drive plugged into it and have set the options to use that drive and the itunes server is turned on. I've rebooted the router many times, removed the drive and put it back in. Turned of settings and turned back on. Nothing works. iTunes does see my PC's shared library just fine.
View 2 Replies View RelatedEverything was working fine and I was poking around in the router settings and clicked the Clone Mac Address button to see what it did and hit Apply.
Now the internet isn't working (on the neighbor's internet) and I can't even get back on the router (192.168.1.1) I reset the router but it still isn't working.
I have an ASUS Wireless Router RT-N66R.
Edit: I got back on the router but now my wireless MAC address is the same as the LAN MAC address. I think this is what the cloning did. Is there any way to find my old MAC address?
The section is titled Special Requirement from ISP so I think I may need to use a certain MAC address but I don't remember what the old one was.
I recently made an old router into a repeater by using DD-WRT. It seems to be working fine if I use LAN, but I cannot get WLAN to function properly. When I go to add a virtual interface and all the proper info, I all of a sudden cannot connect to the Internet. More specifically it seems to not assign me an IP address.
View 1 Replies View RelatedI throw my laptop out the window.
Laptop - Asus X53U
Wireless Adaptor - Atheros AR9285.
Spare USB Wireless - Edimax
A couple of weeks ago, my wireless connection was getting slower and slower. As one day it decided to get extremely slow, I decided to uninstall the wireless card via device manager and reinstall it. Once this had been completed, the wireless just stopped working. The signal bar came up with zero and had a big red X in it. It works fine with ethernet cable but just won't seem to work as a wifi connector.
I have reinstalled all drivers and everything is enabled. When troubleshooting, it comes up with a possible problem with driver. Once this has been resolved it is then a problem with the network. The router is fine as I am able to connect on every other device in the house. I even purchased a USB wifi adaptor in the event of the Wireless card packing in but this is still creating the same problem. I used system restore to roll back the laptop to a time when the wireless worked and it didn't seem to work at all.
I had to move to a remote area in which I can only use a 3G mobile internet connection. The 3G connection is working fine, that is until I plug in my Asus RT-N12 router in order to create a wireless home network between our computers (for file and printer sharing).
For me it seems like firefox is trying to connect to internet trough the router. But that is not possible, since the router has no internet. The only internet is from the 3G mobile internet stick.
How can I tell firefox, that it should look for internet in the 3G connection instead of the router?
my laptop when I'm on any web browser (Chrome, IE, Firefox, etc.) it will say I'm not connected to the internet and stay that way for a minute. Any downloads and stuff I have going still download though and it shos that I am still connected to the internet with excellent strength. This happens with both wireless and Ethernet connection. The only way I can fix it is by disconnecting form the internet and connecting again, even that though only works for like 20 seconds and then it says I'm disconnected again and I have to disconnect and reconnect again.
I don't think its internet connection point either because all my friends and school laptops and desktops have no problems connecting and don't disconnect.
My laptop is an ASUS Notebook G72GX
I have an ASUS u56e laptop running Win7 Pro that I bought in Aug 2011. Unfortunately my problems started when I was working in East Timor and could not take it anywhere except the IT department where I worked. It is true that for a while I was using the LAN at work and also at my hotel where numerous ISPs were used at various points in time.
I have progressively lost almost total use of the wireless capacity of the machine and this is regardless of where I am using the computer (country, state, public or private networks). Very rarely will I have access and then not for long. When it is not working I will get a message saying that a network adapter cannot be found.
I have updated the driver software and experimented with the power settings. I have also uninstalled an ASUS utility that I read might have been a problem. About the only thing that sometimes works is to disable the network adapter, shut down, and then restart the computer. But not for long.
There is WiMax capability that came with the computer, which I bought at Best Buy. Based on IT advice I have made sure that WiMax is off but the wifi button indicates 'on.' When I am having problems though, I cannot see the wifi button.
I am using Windows Firewall and Webroot SecureAnywhere v.8.02.109. At device manager I see for network adapters: Intel(R) Centrino(R) WiMax 6150 and Intel(R)Centrino(R) WirelessN6150. There is also an entry above for a 6150 Function Driver.
I have attached an image of the ipconfig from the ASUS.
I have an ASUS Z77 Motherboard and when I install the AI Suite II which comes on the installation disc it blocks my internet connection. When I uninstall the software my connection is fine. I am using an Ethernet connection by the way. I think it is being blocked by the component called Network iControl. As soon as that component is uninstalled my Internet connection comes back. I want to have the software, but I also want to have my connection.
View 1 Replies View RelatedI recently moved into a larger 2 story house, and for the first few months I was using a Linksys E1000 I've had for about 2 years now. It's a fine single band router, but the people upstairs and the xbox/PS3 in the living room didnt have the strongest connection.
I shopped around and finally got a ASUS RT-N66U for a really good, strong dual band router that would supposedly give better range and performance than my old E1000.
Unfortunately, since I got it everyone is having issues they never had before, namely:Signal dropping all around the house and having to search for the network much slower performance than before the xbox/PS3 cant hold a stable connection even for a few minutes now, when before you could watch Netflix HD programs easily
I've upgraded the Firmware to 3.0.0.3.178 since I heard earlier firmwares had issues, but other than that and opening my ports for qTorrent it is relatively stock settings.
I noticed that my Asus RT-56U router feels really really hot. It's like the sidewalk on a hot day. I was wondering if it's suppose to be like that or if it's a problem i should worry about.
View 1 Replies View RelatedI am having the excact same problem, but I have an Asus F3l, which is only a couple of years old - shouldnt the drivers be valid - ie, hasnt WPA been around for some time?
View 14 Replies View RelatedI currently have a D-Link DIR-615 as my home router, but I've been underwhelmed with its range. Before I go switching stuff around. My D-Link is flashed with dd-wrt, and my RT-10+ would be as well.
My goal would be to increase the range if I could, but not at the cost of dependability. I almost never have to reset the D-Link, but I really don't have any experience with ASUS so I'm not sure where they fall in terms of quality.
So my setup has been built around playing nice with my Uverse Gateway. Basically the Router is hooked into a Lan port to the gateway and I have enabled DMZ-Plus to disable the firewall on the gateway's end. Wireless on the gateway has been turned off.
My issue is if I try and plus my Thecus N4100 pro into the router, it doesn't see it at all. The only way I can get my N4100 pro to work is to plug it directly into the gateway with my desktop pc and in that case the gateway wireless has been turned off only my desktop pc see's the nas...
It's definitely not ideal, and I am not sure what to do. I wanted to be able to use this router to do the bulk of the pc related things and only have the gateway handle uverse tv (WAP)...
I recently bought the above product, the ASUS USB N13 network adapter, and last night when i tried connecting to my wireless router, it worked, but I found that I could only get a maximum on 35% signal, where as my Acer laptop from 2005, receives upto a 100% signal. For a product thats rated at 150m range, distance should not be a problem, I have screen shot if required of the signal strength.
View 4 Replies View RelatedReaders Digest Version: Worked fine yesterday nothing has change in my connection settings, router settings or server settings. (Computer is located at work in an AD setup, I am first level IT Support here) Router shows as it is getting a connection from the network card which is a Realtek PCIe GBE Family Controller with latest drivers right from realtek (and asus version tried too). But is not connecting at 10/100 or 1000. (Have two connection sources to test to).
What I have tried:
- Tried it on a 10/100 router and a gigabyte switch
- Multiple cat5's
- Performing a clean uninstall of the driver and reinstall both from the Asus and Realtek websites of both drivers.
- Disabling the lan rebooting, enabling he lan and trying to connect.
- Disabling power save multiple times.
- Checking bios for any lan options (which there was surprisingly very little options)
- Latest bios firmware
- Tried changing the duplex to 10/100 for the hell of it!
May try:- Reinstalling windows. I had this problem a couple weeks ago, I went into the bios and enabled PXE boot when into windows and it was suddenly working as usual again. Went back to bios disabled PXE and it was still working fine. I did it again today to no avail....
when trying to connect it says nodhcpdiscover received sleeping
View 1 Replies View Relatedwhat is the router name for Asus F5RL
View 3 Replies View RelatedI have one and i try to connect my Ps3 to it wirelessly or wired and it wont work . I have tried everything and now its just pissing me off.
View 1 Replies View RelatedI recently bought a Asus DSL N13 router and one of the points that made me purchase it was the ability to plug a printer in via USB and all users on the network could share this printer. I double checked that my printer (Cannon IP4300) was compatible and its on the list here [URL]. I've set up the router and this work fine, both my desktop (running windows 7 64 bit) and my laptop (running vista 32 bit) can access the router and connect to the internet fine, both via ethernet cable and over wireless connection.
However I've been banging my head against a wall with regards to sharing the printer. I can connect the printer to the router and in the router configuration there is a tab for the printer server and this see's my printer (Cannon IP4300). However when i try to add a new printer on either my desktop or laptop i cannot see the printer, whatever i try!
