IP addresses of the clients connected to Wireless end points are not getting resolved in LMS 4.2 user tracking ? Whether LMS will resolve IP addresses of the clients connected through Wireless end points ?
Note : Those wireless end points are not monitored by LMS
access points are directly connected to 2016 wlc.Event log from the wlc
AP event log download completed.
======================= AP Event log Contents =====================
*Mar 1 00:00:30.157: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:30.161: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:30.190: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:30.191: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
[code]....
but still access points are not functional ?
I have a router that is capable of wireless N at 5.0GHz but can't run simultaneous with it's 2.4GHz band a/b/g (Cisco Linksys E2000), so I have a second router acting as gateway for my b/g devices (and a few wired only that are nearer to it). They are connected LAN port to LAN port with 50ft of cat6 and the DHCP server running on only one router. I know this is pretty standard for multiple access points, and it works very well. But I'm moving, and in the new house, the internet access will be on one floor with the wireless N router, and the other router will need to be in the basement on the opposite end of the house, and running networking cable through the floor and walls is just too much trouble. My question is, can I replace the previous wired method with a wireless N bridge attached to the LAN port of the router in the basement and have it function in the same way as it did when it was wired, with only the DHCP server running on the wireless N router, and all devices attached to either router able to see each other? I would assume so, but I would like to know from anyone who has experience with it before I go buying the bridge.
View 3 Replies View RelatedWe have recently implemented a 3rd party certificate for the guest access, currently have a WLC 5508 that has a Vlan directly connected to our DMZ firewall and NATed out. The problem is when I have installed a 3rd party certificate as per the following link URL
The DNS host name that I entered into the DNS Host name section is not resolved. If I remove the DNS name and leave the virtual ip address 1.1.1.1 then it works fine but just comes back with untrusted message.
I have installed an SR520 with wireless for a client. They have asked if there is an easy way for them to monitor who is connected to the wireless at any given point in time. They are not capable of using the IOS command line.
View 1 Replies View Relatedi have ~ 25 employees which are connected to the AP . I have a 2mb dl and 2mb ul microwave lease line.The AP disconnects ever couple of hours for a minute?
View 3 Replies View RelatedMy question relates to how many clients can be connected to a 2600 series AP. The documentation states 200 clients per radio and the AP has three radios. However when my AP gets to 200 it rejects further clients with the following log: [code] I see this exact message many times and each time the radio mac address is the same and the number of clients connected is 199. The same mac address is used for both 2.4ghz and 5ghz so does this AP have a single logical radio covering both 2.4 and 5ghz frequency ranges and is the limit for all connected clients 200?When viewing the AP details under the Wireless tab it only lists one mac address for each AP for both 2.4ghz and 5ghz frequencies.
View 11 Replies View RelatedI have 1242AG. how many clients can be connected to this AP??
View 4 Replies View Relatedis any way to get information about clients connected to an AP WAP200?
View 2 Replies View RelatedI just installed an Aironet 1602i, standalone WAP. I have it configured to use a RADIUS server in our office. However, two issues have come up when trying to get clients connected.
iPhones and iPads won't connect to either the 2.4 or the 5 GHz radios.
No one can connect to the 5 Ghz radio.
Both radios are UP according to the GUI interfaces of the WAP. Also, laptops and android devices are able to connect to the 2.4GHz radio but not the 5 GHz radio.
I am on the latest version of the firmware.
How many wireless clients can connect to a single WAP321 Access Point?
View 2 Replies View RelatedI use two wlc 4400 (4.2.x version) with a mobility domain and one ssid, both wlc are connected to a cisco l2 switch infrastructure. On the wlc I use the p2p blocking action 'drop' [URL] to isolate the clients from each other. Does only unicast traffic is blocked or also multicast and broadcast traffic like arp requests?Concerning blocking p2p traffic of clients connected to the same ssid but different controllers I found the following statement in the LAP FAQs [URL]
Q. In autonomous APs, Public Secure Packet Forwarding (PSPF) is used to avoid client devices associated to this AP from inadvertently sharing files with other client devices on the wireless network. Is there any equivalent feature in Lightweight APs?
A. The feature or the mode that performs the similar function of PSPF in lightweight architecture is called peer-to-peer blocking mode. Peer-to-peer blocking mode is actually available with the controllers that manage the LAP. If this mode is disabled on the controller (which is the default setting), it allows the wireless clients to communicate with each other through the controller. If the mode is enabled, it blocks the communication between clients through the controller. It only works among the APs that have joined to the same controller. When enabled, this mode does not block wireless clients terminated on one controller from the ability to get to wireless clients terminated on a different controller, even in the same mobility group.
what's the best practise to prevent this inter wlc client traffic? I already read about using acls on the wlc dynamic interfaces, or private vlans on the l2 switch vlans where the dynamic interfaces are connected to. Is it allowed to completely isolate the wlc from each other on these dynamic interfaces with acls or private vlans or do the wlc need to see each other on this interfaces (e.g. heart beat)?
Recently I have installed and configurated an AP 1260, it has already IP, SSID, and ping to the router, but after install the antenna I open the web configuration and see that it has 0 clients connected and the light is always green, indicated as only is configurated with nobody connected.
Tha radio setting is up, 2,4 Ghz and 5 Ghz any issue with the antenna? or i need to configure anything else?
I would like the know if there is a way to know which wireless clients are connected under N mode. There is any kind of command where can show me that ?. I don´t have a wireless controller. My AP is AP-1141N-A-K9
View 2 Replies View RelatedMy controller is vWLC installed in ESXi which has to vNet Cards configured with all vlans(4095), then it is connected to a 3560 switch with trunk. The configuration of the switch interface is as belows: The SSID is BYOD and I can connect the SSID and get the IP address such as 10.10.10.118/24, but for now, i cannot ping 10.10.10.1, but i can ping 10.10.10.90.
View 3 Replies View Relatedwe would like to get Internet from the new router and have it go through a second (old) router on one port and another wired connection on another port. Currently, when we connect the old router to a port, no traffic goes through and dns cannot be resolved.
View 1 Replies View RelatedLately I have been experiencing an annoying issue with my connection. My signal strength is excellent, but every 5-10 minutes I have the problem that the DNS server can't be resolved, so I can't visit any websites. All I can do is wait, the problem disappears after a few minutes. I tried ipconfig /flushdns but that didn't work.
View 5 Replies View RelatedNeed implementation of an OID to view the number of connected clients per Access-Point? I am using a 5508 WLC.
View 4 Replies View RelatedI have a TP-Link TD-W8960N Wireless Router. I would like to know what the I.P. addresses of connected clients are (both those connected wirelessly & those connected by Ethernet cable). There are about 6 computers in my network, some have dynamic and others have static I.P. addresses.I am finding it difficult to navigate the router,on which menus get me to the information that I am interested in
View 1 Replies View RelatedI am struggling with the following issue. I have 6 1130 Accesspoints in lightweight mode connected to a 2106 wlan controller which runs software version 7.0.98.0. Everything seems to work fine. Clients can connect to the wifi network. However, they don't get an ip address from the dhcp server which is on the same subnet as the wlan controller. See attached screenshots for configuration. I have also tried the internal dhcp server of the wlan controller, but the same problem remains.
The logs says: Dropping primary discovery request from AP e8:b7:4x:xx:xx:xx - maximum APs joined 6/6 There are 6 AP's connected
Cisco 881W WLAN module running in autonomous mode. How do I list connected wireless clients?
View 1 Replies View RelatedI have configured 2 RV042 VPN with different ISP. Tunnel connected successfully and i can ping each other router but i can't access clients which are connected to router. I have added rules also in firewall.
View 1 Replies View RelatedIs there a way to know from the web interface the wifi speed of the connected clients?
View 1 Replies View RelatedI have 4 desktops cat5 to Dlink DIR 615 router. All work fine. Any wireless clients, laptop or netbooks, see the desktop computers for a while then disconnect somehow. All machines can see the Internet through the router at all times. The desktops disappear from the laptop/netbooks but the wireless machines can be seen from the desktop computers but clicking on them gets 'Access Denied' message after a wait.3 desktops = XP, 1 98SE. All laptop/netbooks = XP
View 2 Replies View RelatedI have configured 2 RV042 VPN with different ISP. Tunnel connected successfully and i can ping each other router but i can access clients which are connected to router. I have added rules also in firewall.
View 1 Replies View RelatedI have a ASA5505 and it has a vpn set up. The VPN user connects using the Cisco VPN client. They can connect fine (the get an ip address from the ASA), but they can't ping the asa or any clients on the network. Here is the running config:
Result of the command: "show running-config"
: Saved
:
ASA Version 7.2(4)
!
hostname ASA
domain-name default.domain.invalid
[code].....
what I need to add to get the vpn client to be able to ping the router and clients?
We currently have an ASA 5520 communicating with 10 ASA 5510's, all on static outside addresses. I was asked to add 5 additional 5510's on dynamic address. All worked well in testing until it was decided that some of the dynamic clients needed to talk to each other.
My testing shows packets just dying in the 5520.
I have a Netgear WNDR4500 running the stock firmware, acting as a router for my home. I also have 2 routers that are flashed with DD-WRT (Linksys WRT54G and Asus WL-520GU) running as client bridges. The Netgear is 192.168.1.1 and the other 2 client bridges are 192.168.1.2 and 192.168.10.3. The Netgear router is performing DHCP giving addresses from 192.168.10.100 to 192.168.10.254. I have numerous machines connected to the Netgear, wirelessly and wired, and numerous machines wired to each client bridge. All machines have IP addresses that are 192.168.10.100, 192.168.10.101, 192.168.10.102, etc... Everything is working fine, but I have one question: When I access the Netgear router, it shows the client bridges as clients, machines that are wired and wireless to the Netgear router are listed as clients, but the client list does not show any clients that are connected to the client bridges. I assumed that since the router is performing DHCP that all clients would show up.
View 2 Replies View RelatedWe have a Cisco ASA5505 here that provides DHCP and routing to all our devices in our network. We also have a few other switches and wireless access points connected directly to the back of the ASA5505.For the past year all the wireless network signals has been working fine however starting last month, none of the wireless access points (we have three WRT54G) would allow proper connection (dropping connection, slow internet).I thought this maybe all THREE wireless access points are toast/bricked. So i went out and bought brand new Netgear WN604 and even with the new WAP i'm having same connectivity issues (really slow internet).When hardwired directly to the switches we get BLAZING fast internet & connectivity, no issues.
I called CISCO TAC and they automatically said "our ASA5505 is fine, it has to be your wireless access points" not working properly. I explained to them that i also purchased two brand new access points and they are doing the samething now, how can that be?
I've had some long standing issues that I've tried various things to fix. I have two WAP4410N access points set up at a smaller sister company. Wireless clients (laptops) are not receiving DHCP assigned IP addresses. If I type in an IP manually, it works fine.The sister company has a point to point T-1 connection to our main building. Our main building has the DHCP server. The router on the sister company end is configured as the DHCP relay.
I've upgraded the firmware three different times in the past to hopefully resolve the issue, but no luck. Just today, on one of the WAP4410N's, I upgraded to the 2.0.6.1 firmware (backing up config, reset to factory default, upgraded firmware, reset factory default again, restored config). After the first reset to factory defaults, the Access Point itself picked up a DHCP address from the server, and I verified this in the DHCP console on the server, so I know that the DHCP relay is working. However, my laptop would not get a DHCP address when connecting wirelessly through that access point. It is a Windows 7 Enterprise laptop. I also could not get a DHCP IP with my iPhone connecting to wireless, to rule out specific issues with just a laptop.I have the DHCP lease times for the subnet that these WAP4410Ns are on set to 2 hours.
To put a cherry on top, there is one laptop that stays in a lab area at all times, connecting wirelessly, and it DOES get a DHCP IP address (I can see in the DHCP console that the lease for this laptop continually renews as needed). I do remember on initial config when I couldn't get it to work, that I did a manual set up, gained connection, then switched it to DHCP...but that doesn't work for any other laptop.Why would the access points get DHCP address, but not anything connecting to the Access Points?
Using WISM with 7.0.220 and 1240 and 3502 APs. Just found that some of our 3502 AP didn't enbale their clean air and CDP when installed. This only happened on a few new APs. But the area these APs where we seem to have had a few problems with PCs. The only PCs effected where Computer On Wheels (COWs), Dell 780 Desktop with a Cisco Wireless Card.
Using an interl wireless card and others in thes areas worked.Once I enabled the CDP and Clean Air, the COWs worked.My question is with the APs not having CDP enabled, could this affect the cisco wirelss card in the COWs?
At my school we have a lot of access points, but sometimes the computer use the wrong access point. How can I solve that? Is there a program for switching access point?
View 8 Replies View RelatedIm having problems with some toshiba laptops that arnt showing the SSID for some wireless points in the school. We have had the waps set up with the same ssid so we can walk around and the laptops will connect from one to the other. Its been like this for sometime however some new laptops we have got running windows 7 pro show some of the waps up as "other network" - File attached. The actual SSID on ALL waps is Peel Park WiFi Therefore it keeps losing connection to the wireless points and wont connect to some.
View 5 Replies View Related