I have a Linksys X2000 modem. Sometimes I see the "Wi-Fi Protected Setup" button glowing orange (amber?) for no apparent reason. The manual says that it "blinks rapidly in amber if an error occurs" but I don't think any device is trying to connect wirelessly at the time. How can I determine if there is a problem?
View 5 RepliesI tried already several times, may be I entered already a name and password, can`t remember. Anyhow this time I was well documented to start again, but after 192.168.1.1, leaving 'name' blank, and password 'admin', this was quoted as wrong name and/or password. What to do to be able to continue now?
View 2 Replies View RelatedOn Page 16 of my N600 DB manual it says that below the "Router Status Light" and above the "WPS" letters there is a "Wi-Fi Protected Setup (WPS) Light and Button". When I look at my router all I see in this space is a raised rectangular plastic strip. Should I have a light and button there?
View 1 Replies View RelatedMy Linksys X2000 still working but only red power light on (at nomal there are 3 white light on).
View 3 Replies View RelatedCommand to check system status of ACE 4710 appliace? For example if fan is OK or CPU temperature, or other HW things what could be faulty?
For example now I have system ID button blinking amber bot do not know what is wrong. I just know that there is some faulty.I just used show tech-support command and it does not seems that it include some HW statistics.
I was trying to connect Ethernet cable to my laptop LAN port, there was solid Green on my Hub and there was no light on my laptop LAN. I have swapped with a none good working computer and Ethernet cable everything works fine.I felt the problems is the physical LAN port on my laptop.
View 1 Replies View RelatedI have a DIR-615 H/W ver C1.Suddenly everything stopped working. The D-Link light is green and the power light is amber, no other light is up (LAN or Internet).I've try to do a reset, no effect.Can't connect to the router even with a LAN cable (LAN lights stays dead with a working cable and computer plug-in).
View 3 Replies View RelatedI want to switch back to my dell desktop 4600, it is not reading the network or ethernet there is a steady amber light. I clean inside and pulled network card out and put back in and still have steady amber light. I have dsl with att and it works on my laptop.
View 5 Replies View RelatedWe have one Cisco ACE in our data center which is working fine but has Amber light on front & Rear.
I read the document & it shows that either it is a system fault or internal fan failure.
I am sure it is a fan failure because if there was any system fault then ACE dont work properly. should we replace the hardware?
unfortunatley we dont have support contract & i am working to get it one.
We just moved into a new place a couple days ago and the cable guy (from Cox) came and hooked everything up. The cable works but I plugged in my n300 belkin wireless router and it'll have a blue ligh for a couple second then flash and then turn to flashing amber/orange. It won't connect to the Internet. I tried resetting it, unplugging from both ends and nothing will work.
View 2 Replies View RelatedWhat do I do if my routers light stays amber and wont turn blue? The wifi is not working because of this even though it is saying the signal strength is excellent and I have already done the reset a bunch of times its been two days and I just cant get it to work. Its the N300 router
View 2 Replies View RelatedI have a Problem with a ASA 5505 when i power on the ASA the Power LED change to green and the Status light to solid amber. There is no Console output or anything else.
View 9 Replies View RelatedI have an ASA 5505 with status light solid amber color. It is under SmartNet.I'd like to know Cisco will replaced this device with new ASA5505 or upgrade one?
View 2 Replies View RelatedI have (2) Sup 32 configured in a 6509 chassis. I have 1 power supply plugged into the wall and 1 power supply that is not plugged into anything but it is in the chassis and has green light to show that it has been recognized.
My problem is the "system light" on both sup32 remains amber and does not turn green. I have done show modules and sh diagnostics and sh power and everything checks out OK. Also there is an amber light on "active" on the 2nd Sup32 which I am assuming means that it is in standby mode so that would be correct.
Q: My question is could it be the power supply that is not plugged into anything causing the "system light" to stay amber and not turn green?
Q: Will this amber system light on the Sup32 stop the 6509 from running as normal?
How can i add several vpi / vci to my Linksys x2000 ?
View 7 Replies View RelatedI have recently wiped my hdd and installed WinXp, I use to have vista but a crash occurred. I have WinXP SP3 with a Belkin Connect N150 connected to a Arris Telephony modem from Comcast. My setup use to work on vista. I've ran belkin setup from the disc multiple times and it gets to the part where it says connect and make sure cables are connected. All cables are connected, but my router has a solid amber light. I can access arris through wired internet, but I really want my wireless to work.
View 3 Replies View RelatedJust picked up a X2000 and Cisco connect configured my connection, and assigned an IP to my desktop pc.I configured my PC back to a Static IP which is outside the DHCP range in the X2000, and all seems to be working ok..now looking in the web-based X2000 setup screen my pc is no longer listed as a client...so should I manually add it as a client and assign the IP & MAC address in the Cisco setup or is this not necesary.?
View 5 Replies View RelatedI have the X2000. It has 3 ports. I need 4. I also have the WRT160N V3 router which has 4 ports. Is there a way to use this router with the X2000 to get the 4 ports I need ? If not, what are my other options to get 4 ports ?
View 2 Replies View RelatedI've tried everything to get this to produce an i.p address but to no avail.I check with my ISP (o2/BE) they told me all my settings are correct it syncs but just does not pick up an IP address.
View 6 Replies View Relatedlinksys x 2000 modem unfortunately, when I turned the modem on today, the power light which normally was white became red.I tried all the ways I knew, such as restarting in 5 or 30 seconds intervals but unfortunately it didn't work
View 3 Replies View RelatedTrying to replace old modem with the X2000 but it will not connect to the internet, my provider is ATT DSL.
View 2 Replies View RelatedI cannot get my X2000 to connect to my ISP in the UK. From what I've read elsewhere I'm not the only one but I need to determine whether this is a router support issue or ISP.
View 9 Replies View RelatedHow to change the frequency on X2000
View 1 Replies View RelatedI installed my new X2000 a couple of days ago and my ADSL connection drops several times a day. Sometimes it will stay connected for a few minutes and other times it will stay connected for several hours. The only way to get it connected again is to reboot.I have used 2 other routers (D-Link DIR-300 and BT Home Hub 3.0) on the same line and haven't had any disconnection issues with them, so the problem must be a hardware/software fault on this router or I have set it up incorrectly.Judging by a number of posts I found online, there seems to be a general problem with DSL connections dropping on the X2000, especially on earlier firmware versions. I have subsequently upgraded to the latest firmware (Ver.2.0.01 (Build 4)), reset and reconfigured twice, but nothing has worked so far.Unless I can get this working in the next few days I am going to have to return it, which is a shame because the performance of the router is great when it's working!Would someone be able check I have configured the DSL settings on the router correctly?
DSL SettingsEncapsulation: RFC 2364 PPPoAMultiplexing : VCAutodetect: DisableVPI: 0VCI: 38Modulation: MultimodeMTU: 1400
I have been setting up my new Cisco X2000 wireless router recently and I have it working fine for my desktop/laptops and even the PS3, however for some reason when you try to use the wireless on some of the other computers in my house it doesn't work unless you are using a wireless guest account.
View 2 Replies View RelatedCan the 2 WAN ports be connected at the same time to provide failover and if so can this be configured for priority/ delay etc.A user has a very poor ADSL service so also has a bidirectional satellite link. Due to the latter's high latency I don't want it dropping that connection too quickly.
View 1 Replies View RelatedSo its the 3rd day of my nightmare to set up this cisco ADSL router...
Status:
Setup:
DSL connection:
So I live in Ireland and im on Smart telecom ISP, Basicly the internet is half going - like skype is going and i can chat with my contacts, cisco.com page is going but really SLOW, google.com page is going until search, speedtest.net page is going until the mesure thing facebook loads like in 10min.. a lot of pages dosent even go...From main telephone socket to the router is only 2.5m telephone cable(NO HOME PHONE) so no splitter or extension... (Changing the MTU dosent change anything...only if i set it on auto then w7 shows that internet is connected, skype works but no pages at all is loading and is dropping with timeout error.. if i set to manual then something loads on pages...) The cisco connect software does NOT do good because I can go until the username/pasword step, I input THE CORRECT details but he just sayes that he cant authenticate the username & pasw... and so i cant get past that step and the programm is no good.... only way is to set up with 192.168.1.1!
How can I get Max network LAN speed from the X2000.I am connecting with a Macbook and an iMac both with N speed aiport cards.When checking the network speed through mac 'Network Utility' it is only getting 130 Mbps.Should it be getting closer to 300 Mps?
View 3 Replies View RelatedI run a X2000 router for some weeks and it works properly basically - with one exception.WIFI attached devices (Win7, Vista, Android) can go to the internet without having any problem. But they cannot access my local servers (Media-Server, Storage server). I access with normal settings (not the guest) but the behavior is similar to what I expected from the guest-WIFI: protect resources in LAN.Anyway, for historical reason I have also another WIFI Hotspot in the LAN what is connected to the X2000 via cable. If the same devices connect to this hotspot, everything works fine. So the problem isn't caused by the servers.
View 9 Replies View RelatedI'm having trouble with my Linksys X2000 modem/router to stay connected to internet. I have tried upgrading the firmware & changing my ip address, but still with no success.The router part is staying connected, but the dsl will drop off. I have to unplug to get it up and working again.
View 9 Replies View RelatedI have been trying this for ours and need to get it to work for a small branch office so I can get their cisco device connected and phones working.
The device works fine if I assigned it an IP address but the minute I set bridge mode only and assign the static IP to my system then nothing works. I have the latest firmware.
I just bought a new wireless modem router Linksys X2000 And I couldn't find the line status like SN margin and line attenuation and so on [URL]
how to access my ADSL line status
I'd really like to be able to monitor DSL traffic on my X2000. SNMP is the logical way to do this; Looking at the source to the Management screen, it looks tantalizingly close, but the SNMP bits are commented out in the HTML.
View 4 Replies View Related