Cisco Application :: 4710 ACE Hardware (Amber Light)
Oct 30, 2011
We have one Cisco ACE in our data center which is working fine but has Amber light on front & Rear.
I read the document & it shows that either it is a system fault or internal fan failure.
I am sure it is a fan failure because if there was any system fault then ACE dont work properly. should we replace the hardware?
unfortunatley we dont have support contract & i am working to get it one.
View 1 Replies
ADVERTISEMENT
Apr 17, 2013
Command to check system status of ACE 4710 appliace? For example if fan is OK or CPU temperature, or other HW things what could be faulty?
For example now I have system ID button blinking amber bot do not know what is wrong. I just know that there is some faulty.I just used show tech-support command and it does not seems that it include some HW statistics.
View 4 Replies
View Related
Jan 31, 2011
I was trying to connect Ethernet cable to my laptop LAN port, there was solid Green on my Hub and there was no light on my laptop LAN. I have swapped with a none good working computer and Ethernet cable everything works fine.I felt the problems is the physical LAN port on my laptop.
View 1 Replies
View Related
Mar 24, 2013
I have a DIR-615 H/W ver C1.Suddenly everything stopped working. The D-Link light is green and the power light is amber, no other light is up (LAN or Internet).I've try to do a reset, no effect.Can't connect to the router even with a LAN cable (LAN lights stays dead with a working cable and computer plug-in).
View 3 Replies
View Related
Nov 24, 2012
I want to switch back to my dell desktop 4600, it is not reading the network or ethernet there is a steady amber light. I clean inside and pulled network card out and put back in and still have steady amber light. I have dsl with att and it works on my laptop.
View 5 Replies
View Related
Apr 14, 2010
I have a Problem with a ASA 5505 when i power on the ASA the Power LED change to green and the Status light to solid amber. There is no Console output or anything else.
View 9 Replies
View Related
May 4, 2013
I have a Linksys X2000 modem. Sometimes I see the "Wi-Fi Protected Setup" button glowing orange (amber?) for no apparent reason. The manual says that it "blinks rapidly in amber if an error occurs" but I don't think any device is trying to connect wirelessly at the time. How can I determine if there is a problem?
View 5 Replies
View Related
Nov 25, 2012
We just moved into a new place a couple days ago and the cable guy (from Cox) came and hooked everything up. The cable works but I plugged in my n300 belkin wireless router and it'll have a blue ligh for a couple second then flash and then turn to flashing amber/orange. It won't connect to the Internet. I tried resetting it, unplugging from both ends and nothing will work.
View 2 Replies
View Related
Apr 25, 2013
What do I do if my routers light stays amber and wont turn blue? The wifi is not working because of this even though it is saying the signal strength is excellent and I have already done the reset a bunch of times its been two days and I just cant get it to work. Its the N300 router
View 2 Replies
View Related
Oct 14, 2011
I have an ASA 5505 with status light solid amber color. It is under SmartNet.I'd like to know Cisco will replaced this device with new ASA5505 or upgrade one?
View 2 Replies
View Related
Feb 20, 2012
I have (2) Sup 32 configured in a 6509 chassis. I have 1 power supply plugged into the wall and 1 power supply that is not plugged into anything but it is in the chassis and has green light to show that it has been recognized.
My problem is the "system light" on both sup32 remains amber and does not turn green. I have done show modules and sh diagnostics and sh power and everything checks out OK. Also there is an amber light on "active" on the 2nd Sup32 which I am assuming means that it is in standby mode so that would be correct.
Q: My question is could it be the power supply that is not plugged into anything causing the "system light" to stay amber and not turn green?
Q: Will this amber system light on the Sup32 stop the 6509 from running as normal?
View 5 Replies
View Related
Oct 16, 2011
I have recently wiped my hdd and installed WinXp, I use to have vista but a crash occurred. I have WinXP SP3 with a Belkin Connect N150 connected to a Arris Telephony modem from Comcast. My setup use to work on vista. I've ran belkin setup from the disc multiple times and it gets to the part where it says connect and make sure cables are connected. All cables are connected, but my router has a solid amber light. I can access arris through wired internet, but I really want my wireless to work.
View 3 Replies
View Related
Mar 27, 2013
Report run via Individual Web server URL’sThe report takes less than 20 minutes (average 15 minutes) to fetch and return the data. This is observed 9 out of 10 times.Report run via ACE Load Balanced URLThe report keeps on running for more than 20 minutes and never completes. The front end keeps showing report is running.The data in general when tested directly by running queries against the database (bypassing the platform) completes in 15-18 minutesThe network connectivity for each and every ports involved (Loadbalancer/Servers) have been throulgly checked.
View 6 Replies
View Related
Feb 2, 2013
i'm looking for a recommendation for a setup guide including ft i've had a quick look a wiki and i can get basics but i'm not sure about if i need to setup additional contexts etc when i'm the only one using the appliance?
View 2 Replies
View Related
Aug 26, 2012
I have an issue with a customer that wants to update a server behind the ACE. The problem is that when the application wants to update the server it does it with the name.Doing some research I found that you can rewrite the record DNS based on the static NAT you set up on the ACE. The feature is called DNS inspection. Is the same feature as the ASA (DNS doctoring).I apply it to the outside interface and it did not work.
View 1 Replies
View Related
May 7, 2013
What are these ports used for? What can I do with them?
View 2 Replies
View Related
Feb 12, 2013
I am trying to configure sticky on an ACE 4710 and don't understand what the netmask part of the sticky ip-netmask netmask address {source | destination | both } name command.
Some examples use 255.255.255.255 and others use 255.255.255.0 but I don't know what the significance is or what it does?
I am going to configure for both source IP and destination IP (both).
View 2 Replies
View Related
Mar 19, 2012
With the current (A5) ACE 4710 lic setup, does the "X gigabit per second appliance throughput" that is licensed affect: -
A) Only "appliance" i.e. load balancing traffic, any other normal routed traffic is not included in the limit
or
B) Is it an overall throughput limit on the interfaces i.e. includes all traffic not only load balancing traffic but also normal routed traffic crossing the appliance
Looking at a scenario where the lic size I need for HTTP load balanacing would be one size if A) but would need to be much larger is B) to accomodate out of hours routed backup traffic crossing the ACE 4710
View 1 Replies
View Related
Aug 27, 2012
I've just run the ACE 4710 and it seems that is booting up well but it stops when 'Setting up dynamic memory size' message appears.
INIT: version 2.85 booting
b4 lspci
1 Cavium device(s) found.
[Code]....
View 2 Replies
View Related
Aug 11, 2012
I've got a web app that the owners want to run over port 80, but also using SSL to secure private data in transit. The architecture is an ACE 4710 in SSL termination mode->Apache (port 2000)->Back-End app server.
I've got two VIPs set up already - one on port 443 and one on 2000 - both of which do the SSL termination quite nicely, but using the 3rd VIP set up on port 80, the connection steadfastly refuses to be HTTPS (i.e. doesn't show the padlock).
I've done all the set-up through the web interface so far, can this be done? If so, how?
View 1 Replies
View Related
Jul 19, 2011
I am currently running A3(2.6) and evaluate the possibility of upgrading to A4(2.1). The Instal & Upgrade Guide A4(2.0) mentions that A4(2.0) does not include all features of A4(1.1). Does this apply to A4(2.1)? The Release Notes mentions a list of features merged from A4(1.1) to A4(2.1) but does not clarify if there any features not merged.
[URL]
View 1 Replies
View Related
Nov 13, 2012
we configued An ACE 4710 with SSL termination on Oracle Aplication Server 10g (10.1.2.0.2) ,so that SSL termination is done on the ACE and HTTP reaches the Oracle Aplication Server 10g (10.1.2.0.2) then we configure the ACE to enabled client authentication with Pkcs#11 smart card token certificate and this don succfully my problem need do this client certificate authentication for only the [URL] not for all SSL proxy service how can do that.
View 3 Replies
View Related
Dec 5, 2011
I'm receiving a lot of these messages in a ACE4710 cluster. 192.168.100.1:80 is the VIP, 193.126.127.28:56380 is the client. Already tried to set the mss with this:
parameter-map type connection my map set tcp mss min 0 max 1380
policy-map multi-match L4_policymap
class vip_PRDWEB_http
loadbalance vip inservice
[code].....
But it doesn't work.
View 4 Replies
View Related
Jul 31, 2011
We have recently transitioned one of our Ecommerce products to a new data center, at which we now use a one-armed load balancing approach rather then the routed load balancing approach we used previously. This is casuing us some issues as we generally log the source IP address a user comes in on when he fills out an application. Now the logs only show the natted ip address recieved by the load balancer, which does us no good. Any way to log the source IP address when a new connection is created to a particular vip?
View 3 Replies
View Related
Jun 2, 2011
If we use an ACE4710 to load balance two real servers, obviously it will use health checks to determine if a server is down.When it detects a server is down, it will not send it any more traffic.But can we also have it take any other action? For example maybe email an admin, or send an SNMP trap? Or better yet, can we use a custom TCL script to do other things, like launch some custom activities?
View 2 Replies
View Related
Jan 24, 2012
I am new to the 4710 appliance.Apart from the 4 GE 'data' ports, there are 2 Ethernet 'management' ("console") ports. I find the description in the "quick start guide"somewhat confusing. URL, Is a first-time serial connection (at least to run the initial config. script) mandatory? Or can you obtain the same result via one of the 2 Ethernet management ports and using a default ip address (192.168.1.10 ? When running the initial config. script (only possible from the serially connected console i suppose), you have to select your management port. Why does the system in step 5 proposes you 4 ports, and not just 2? I suppose the intended port for management is one of the 2 management ports, not one of the 4 data ports?
View 1 Replies
View Related
Jun 29, 2012
I have a pair of ACE 4710s with 12 contexts sharing the load, running A4(2.1). esterday I upgraded one of them to A4(2.3) now I cannot telnet to the Admin context.Pings ok. I can telnet to other contexts on the box and everything seems to be working ok when i do a " sh telnet" comes back with
No Session Information is available
sh telnet maxsessions
telnet maxsessions 16
View 1 Replies
View Related
Dec 14, 2011
ACE# sh script code NORDICID_PROBE.Error: Called API is invalid or non-existant.Hardware is ACE-4710-K9 and software A3(2.7)The probe itself is functioning ok according to show probe detail.However show script script_name probe_name -counters all remain at zero for some reason. This wasn't the case on the previously use ACE software.To my recollection the command show script code has worked successfully before on the same ACE software. Not 100% sure though, but it definitely worked on the previous software we ran on the ACE.
View 2 Replies
View Related
Jan 30, 2012
the ACE 4710 is running 3.2.5 and I need to put it in another environment.Is there a way to reset its settings?
View 3 Replies
View Related
Aug 22, 2011
Any document that details the steps to change the FT ip addresses of a pair of Cisco 4710 whilst they are running in a production environment without causing an outage?
Would the steps be:
On the secondary unit:
hbs-syd04-lb01ft interface vlan 417 ip address 172.30.254.221 255.255.255.252 peer ip address 172.30.254.222 255.255.255.252
Then on the primary unit:
hbs-syd04-lb01ft interface vlan 417 ip address 172.30.254.221 255.255.255.252 peer ip address 172.30.254.222 255.255.255.252
Or Vice Versa?
View 1 Replies
View Related
Oct 23, 2011
Is this normal to have millions of current connections within an ace 4710? There is only 3 current connections but shows a high number?
View 3 Replies
View Related
Jan 25, 2012
I have a pair of ACE 4710's running software version A3(2.0). I intend to upgrade to version A5(1.2). Can I go straight to version 5 or do I need to go to version 4 and then version 5?
View 1 Replies
View Related
Oct 6, 2011
We have two pairs of ACE 4710s, one pair running A3(2.4) and the other pair A3(2.0). We plan to upgarde the second pair so that they are running the same image as the first pair (we know they are not the latest, but this is the first step in a larger rollout plan, and to aid some troublshooting for a major issue we are seeing.)
I have details of the upgrade steps, but my question is with regards to the licenses which are now enforced after (2.0). We currently have the following on the first pair, but are these part of the default licenses for (2.4) or would we need to purchase these as well?
ACE-AP-500M-LIC
ACE-AP-C-100-LIC
ACE-AP-OPT-50-K9
ACE-AP-SSL-05k-K9
View 2 Replies
View Related