I have a few 3560E running Ver 12.2(50)se2. Can these boxes be configured to run VRF. I see a "sho IP VRF" option, but I do not see it available when under config t. Do I need to do a IOS upgrade to be able to configure VRF?
View 7 RepliesI upgraded four 3560E, 12.2(44) to 12.2(55)SEThree 3560 works fine, the last one stops after 17-18 seconds with a solid green LED. I cant get into ROMmon, the switch doesn't boot up. its like "dead but still alive"
My TS:
1: Removed all SFPs.
2: Reset PSU and fan modules.
3: Replace PSU and fan modules.
4: Try to get into ROMmon.(pushing mode button and break seq.)
Startup LED:0-1 seconds: SYST: Amber RPS: Amber STAT: Green DUPLEX: Green SPEED: Green
1-17 seconds SYST: Blinking Green RPS: OFF STAT: OFF DUPLEX: OFF SPEED: OFF
18 s--> (only testet up to one hour) SYST: Solid Green RPS: OFF STAT: OFF DUPLEX: OFF SPEED: OFF
A working 3560EStartup LED information. If I compare a working switch with the faulty switch I can see about 18 seconds into bootingSYST change very fast from green to amber and continues with booting,this doesnt happened on the faulty switch (solid green 18 seconds). Pushing MODE button, doesn't get me in to ROMmon, this works for all the other switches.On a normal 3560 it takes around 40 seconds before I get in to ROMmon. With this faulty switch it stops after 18 seconds(solid green) and it doesnt respond.
We have two Cisco 3560E layer 3 switches at the core of our network. The switches are configured as an HSRP pair and the clients on our network point to the HSRP address as their default gateway. So if CORE-A dies, then CORE-B will pick up the address and the default route for the clients will continue to be available.We also need to specify a few static routes on the core switch to allow us to get to specific networks. Is there a way to do this so that the routes failover in the same way that the default gateway does?
View 2 Replies View RelatedI have a 3560E with 2 vlans that I want to route between. one device with 2 vlans and route between.Interfaces are configured as such:
int g0/11
switchport mode access
switchport access vlan 10
int g0/12
switchport mode access
switchport access vlan 11
[code]...
Laptops on each port with 10.10.10.2 and 10.10.11.2 configured on them. I can ping from 10.10.10.2 to 10.10.11.1, but not to 10.10.11.2.What do I have to configure to be able to get the 2 laptops to talk to each other?
I am looking for a PoE switch with Routing capabilities (e.g osfp) something lower end than 3560E.
View 10 Replies View Relatedrecently a Cisco 3560E switch went down due to a power surge. the switch is getting power but i am only seeing the below message continously. it is keep on rebooting. i try to reset to factory settings/ safe boot nothing worked. is there any way i can bring the switch up or it is hardware failure.Using driver version 1 for media type 2Base ethernet MAC Address: 00:23:33:af:1b:00Xmodem file system is available.The password-recovery mechanism is enabled.Using driver version 1 for media type 2Base ethernet MAC Address: 00:23:33:af:1b:00Xmodem file system is available.The password-recovery mechanism is enabled.
View 5 Replies View Related3945 is running c3900e-universalk9-mz.SPA.151-4.M2
3560e is running c3560e-universalk9-mz.150-1.SE
I've got brand new 3945's with onboard 16-port 3560e switches. On the first power up I see that there are several new vlans added that appear to be default vlans..
vlan 2 name fst2
vlan 3 name fst3
vlan 4 name fst4
vlan 5 name fst5
vlan 6 name fst6
vlan 20 name VLAN0020
vlan 21 name VLAN0021
vlan 22 name VLAN0022
vlan 23 name VLAN0023
vlan 99 name VLAN0099
I deleted the vlan.dat and reloaded the switch but these vlans come back. What these vlans are intended for and is there a better way to get rid of them? What does "fst" stand for?
I have a cisco 3560E switch setup with LACP, when using LACP i receive alot of packet loss / output drops
When a ping from the server behind LACP:
--- google.com ping statistics ---
44 packets transmitted, 39 received, 11% packet loss, time 42990ms
what would cause this packet loss with lacp?
some output from the switch:
Port-channel12 is up, line protocol is up (connected)
Hardware is EtherChannel, address is d0d0.fd58.7390 (bia d0d0.fd58.7390)
Description: LACP-PORT
[Code]....
I implemented the 3560E switch, this one have two Giga bit ethernet/10-Gigabit Ethernet module slots. I used the Twin Gig Converter Modules and one SFP. All configuration was applied in the Ten Giga bit, however the interface giga bit ethernet is UP UP state and the Ten giga down down.
View 3 Replies View RelatedI'm trying to configure "IP PIM SPARSE-MODE" command on a vlan interface on a 3560E switch but it doesn't give me the option to do this. The only option available is ip pim passive. What would cause this ? On the same switch a physical interface is already configured with IP PIM SPARSE-MODE.
View 2 Replies View RelatedI recently upgraded a remote site of mine to IOS 15-2.SE ipbasek9 on 3 3560E series switches. On switch number 2 I have 5 VG224's running (vg224-i6k9s- m) 12.4(22)T3. After the switches reloaded the VG224's dropped their connection. After doing all basic troubleshooting I reloaded the 12.2 (58)SE2 ipbasek9 image back on to the 3560E's and the VG224's reconnected immediately after reload and all phones registered.
Is the problem a licensing issue with the 15.x IOS on the 3560's or do I need to upgrade the VG224's to IOS 15.x as well for them to connect and operate via the 3560e switch running 15-2?
I have 3560e which doesn't appear to be passing igmp traffic to the upstream router
PC1 ----------- ASA ------------ PC2--------- 3560e ----------- 3825 -------------------- WAN --------------------- Router ------------- Server
My ASA runs SMR, has an igmp forward interface outside command on the inside and has a trunk port to the 3560e (V lans 32 & 48).PC2 is a test pc on the 3560e on vlan32. 3825 is my ISPs router on vlan32.
- if i try to access the stream from PC2 it works.
- if i try to access the stream from PC1, i see the igmp join leave my ASA onto the 3560E (i've captured on the 3560e's link to the ASA).
I've also captured on the ASA and i can see the igmp packet leave the outside interface but the join doesn't reach the 3825 (i've captured on the 3560e port facing the router and there is no join being forwarded).the switch is running in layer 2, 12.2(35r)SE1.
switch#sh ip igmp snooping querierVlan IP Address IGMP Version Port---------Switch#
Global IGMP Snooping configuration:------------------------IGMP snooping : EnabledIGMPv3 snooping (minimal) : Enabled Report suppression : Enabled TCN solicit query : Disabled TCN flood query count : 2Robustness variable : 2Last member query count : 2Last member query interval : 1000
We have a Site that is connected via Wireless Bridge to the Main Site, the site is on separate VLAN with Cisco 3560 switch. The main site has 6509 swith. Configuration as per attached diagram. We are connecting a fiber between the remote and the main site and adding a 3560E switch at the remote site, however we would like to keep the wireless connection as a backup in case the fiber is severed the wireless will be availble. Attached diagram shows detailed cofiguration. I would like to know what should I change to make this working. STP is enabled on all switches.
View 3 Replies View Related We have a 24 port and 48 port 3560 E switches with identical IOS the 48 port switch supports private vlan while 24 port switch doesnt
configure private vlans on 24 ports 3560e and is it best practise to configure private vlan on this platform(3560)?
IOS version : C3560E Software (C3560E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
flash:/c3560e-universalk9-mz.122-55.SE3/c3560e-universalk9-mz.122-55.SE3.bin
is it possible, to use a Catalyst Switch (in my case a 3560E) as a source for a console session to another Catalyst? In principle to use it as a console terminal server.
View 1 Replies View RelatedI need to know the key functional differences between the Catalyst switches 3560E, 3560X and 3560G.
View 1 Replies View RelatedWe are receiving a large amount of output drops on 4 interfaces that connect to microwave wireless.This is playing up with our Management system. Saw a bug report but that was for 3750, not the IOS version but was a similar issue. [code] The output errors tend to happen at the same time. All ports are trunks however there are other trunks on the switch that are not having these issues. [code]
View 7 Replies View RelatedI need 10gigbit uplink for this switch. What are the other devices that i need order along with this device.And what is the diff between X2-10GB-LR= and CVR-X2-SFP.if i take CVR-X2-SFP, in future how can i upgrade from one gig to 10 gig?for current use i need 10gig support required. so what are all the other devices that i need to order.Fiber multimode and distance 15Mt only.
View 2 Replies View RelatedWe have a working PBR route map on a 6509 switch and a 3750 switch, each in different locations.On both devices, the route-map is configured to match on one of multiple ACLs, then set the next hop to a directly-connected IP address, like so: [code]
When copying in the ACL contents for "ACL20", they were accidentally copied in to the ACL1 list, and ACL20 was never created. Shortly after this was done, the next hop router went unreachable in both locations. Pings failed and the 6509 and 3750 each lost the EIGRP adjacency to the 1.1.1.5 router. After troubleshooting, I removed "match ip address ACL20" and connectivity returned.
My question is...if a PBR route-map tries to match on a non-existent ACL, what happens? Does it mark the next hop unreachable (even though it's directly connected) or does it match for ALL traffic and send *everything* there (thus, making it appear unreachable, as if a broadcast storm was happening)?
In the following scenario, how will the 2950/2960/2960S series behave:
- VTP server/domain configured on a 6509
- A access switch (2960) currently configured in transparent mode with all VLAN it requires
Will the switch drop any traffick if we change it from transparent to client mode if the VTP server has the exact same vlans defined as the access switch had when it was in transparent mode?
I have an 2960S all configured, with vlans, ports configurations and others.Now, I bought other 2960S and two stack modules to create a stack with these 2 switches.We call:
-Switch1 (I have configured and in production)
-Switch2 (New switch, no configured)
Can I connect these two switches in stack without lost the configuration of my Switch1 and no turn-off this switch? Does not stop the users access?
I've created the VLAN on the Database but it tells me that there are no VLANs configured when i issue the command. Both VLAN 110 and 111 status are down, down.. Below is my config:
Building configuration...
Current configuration : 15817 bytes!upgrade fpd autoversion 12.2service timestamps debug uptimeservice timestamps log uptimeno service password-encryptionservice counters max age 10!hostname Router!!no aaa new-modelip subnet-zero!!!ipv6 mfib hardware-switching replication-mode ingressvtp domain Marinersvtp mode transparentmls ip multicast flow-stat-timer 9no mls flow ipno mls flow ipv6no mls acl tcam share-globalmls cef error action freezeno scripting tcl initno scripting tcl encdir!!! !!!!!!!redundancymode ssomain-cpu auto-sync running-configspanning-tree mode pvstno spanning-tree optimize bpdu transmissiondiagnostic cns publish cisco.cns.device.diag_resultsdiagnostic cns subscribe cisco.cns.device.diag_commands!vlan internal allocation policy ascendingvlan access-log ratelimit 2000!vlan 110name Data!vlan 111name Voice!vlan 112name Video!------------Output
[code]....
I'm working on my CCNA. I purchased an old router 2610 with two ethernet ports. I configured the IP addresses on the interfaces and added the default gateway. I configured NAT to go out my ATT DSL router to the internet. With the 2610, I'm able to ping the back end or internal DSL router, but I can't ping the front end, external router, or out to any internet site such as google.
View 10 Replies View RelatedI have cisco 881 and configured with http access, but when i try to open in browser it's shows blank page. Is the Cisco 881 supports GUI ?
View 3 Replies View RelatedI am trying to figure out what is heat dissipation of a C6509-E configured as follows:
1 x WS-C6509-E-FAN
1 x VS-S720-10G-3C
1 x VS-F6K-PFC3C
8 x WS-X6748-GE-TX
8 x WS-F6700-DFC3C
2 x WS-CAC-6000W
I have tried two ways: 1) the power calculator and 2) manual calculation using the C6500 installation guide.
1) The power calculator says 13630 BTU/h
2) Manual calculation says: [code]
The there should be also the two PS in the picture, and the new total should be: [code] Well, 62711 BTU/h looks quite a bit too much and I think that the heat dissipation of the power supply should't be considered in the calculation.Isn't it an item that takes power from the grid and that generates heat according to its efficiency as the other modules?
Trying to apply this config to a 2900 router and getting this error message. [code] This works ok in in a 2800 router using 12.4(25d) spservices IOS
Not working on 2911 using 15.2(3)T2 ipbase image.
We are trying to test multicast between VRFs configured on Nexus 7Ks. Two Nexus 7Ks are configured for VPC. Multicast Server is in one VRF where as Receiver is in another VRF. The two VRFs are connected to each other via Checkpoint Firewall (Active/Active cluster in unicast mode). All routes have been established and connectivity tested between multicast server and receiver using ICMP.Using, windows mcast.exe multicast stream is generated from server (in one VRF) intended to be received by receiver (in second VRF). Every time, only one multicast packet is received by the receiver and rest all packets are being dropped. Server and Receiver are VirtualMachines configured on VMWaresame chassis which is connected to two Nexus 5Ks (VPC configured).
View 1 Replies View RelatedI have a switch that I have configured for jumbo packets, but they don't seem to be functioning. I have set system mtu jumbo 9000. The hosts are connected via 2x EtherChannel links. The hosts are jumbo frame enabled, and can ping their own local address using jumbo packets & do-not-fragment flags on the pings. They cannot, however, ping each other or the switch that way - it always says that the packet requires fragmentation. I know the attached machines (they're all VMs) and virtual switches support jumbos because I can ping within the virtual interfaces of the VMs. It's just traffic that goes over the switch that fragments.The switch is a WS-2960G-48TC. Here are the various outputs, with a section of config at the end.
hrnacancwtdevs3#show system mtu
System MTU size is 1500 bytes
System Jumbo MTU size is 9000 bytes
System Alternate MTU size is 1500 bytes
Routing MTU size is 1500 bytes
[code]....
how my switches are configured, a cisco 3750 and a cisco 4506.[code] i can ping the gateway from the 3750 however cannot get anything past that or enything to it.
View 12 Replies View RelatedI have two Cisco 4506's running cat4500-ipbase-mz.122-50.SG3.bin. Periodically, when attaching a new workstation to these switches the Mac Address of the device disappears off the port when the device is connected or the port is configured. The only way to correct the issue is to do a hardware reset on the blade or reboot the switch. After resetting the blade or rebooting the switch the devices will start showing up on the port and connect. This does not effect devices that are already connected to the switch, just newly added devices
Both switches are populated with WS-X4148-RJ45, WS-X4148-RJ45V and WS-X4248-RJ45V blades. It doesn't matter which blade the new device is being connected to. I believe that this may be a "Bug" but have been unable to locate one.
I configured port security on my 2960 switches with the following commands: [code]
The problem is that when I should change someone's PC, first I disable port-secirity, then I clear all the mac addresses learned on the interface, then I plug the new PC and enable port-security. The new PC couldn't connect to the network and it's mac address has not be learned on the interface. Why?Which commands should I use to clear an old mac address and enable port-security with the new mac address.
I would like to know how many port channel can i configured in the switch 3750 X ? and if there is a limitation by IOS ?
View 4 Replies View RelatedI have configured Cisco 1841 router PAT buts its not worked, find the below configuration details,
In LAN interface
Interface gigabit Ethernet 0/0
no shutdown
[code]......
Similarly I have configured static and dynamic nat but its not works in my customer place.