Cisco Switching/Routing :: VG224 Quits After Upgrading IOS To 15 On 3560E Switch
May 15, 2013
I recently upgraded a remote site of mine to IOS 15-2.SE ipbasek9 on 3 3560E series switches. On switch number 2 I have 5 VG224's running (vg224-i6k9s- m) 12.4(22)T3. After the switches reloaded the VG224's dropped their connection. After doing all basic troubleshooting I reloaded the 12.2 (58)SE2 ipbasek9 image back on to the 3560E's and the VG224's reconnected immediately after reload and all phones registered.
Is the problem a licensing issue with the 15.x IOS on the 3560's or do I need to upgrade the VG224's to IOS 15.x as well for them to connect and operate via the 3560e switch running 15-2?
View 1 Replies
ADVERTISEMENT
Apr 23, 2012
I need 10gigbit uplink for this switch. What are the other devices that i need order along with this device.And what is the diff between X2-10GB-LR= and CVR-X2-SFP.if i take CVR-X2-SFP, in future how can i upgrade from one gig to 10 gig?for current use i need 10gig support required. so what are all the other devices that i need to order.Fiber multimode and distance 15Mt only.
View 2 Replies
View Related
Jan 27, 2012
recently a Cisco 3560E switch went down due to a power surge. the switch is getting power but i am only seeing the below message continously. it is keep on rebooting. i try to reset to factory settings/ safe boot nothing worked. is there any way i can bring the switch up or it is hardware failure.Using driver version 1 for media type 2Base ethernet MAC Address: 00:23:33:af:1b:00Xmodem file system is available.The password-recovery mechanism is enabled.Using driver version 1 for media type 2Base ethernet MAC Address: 00:23:33:af:1b:00Xmodem file system is available.The password-recovery mechanism is enabled.
View 5 Replies
View Related
Nov 2, 2011
3945 is running c3900e-universalk9-mz.SPA.151-4.M2
3560e is running c3560e-universalk9-mz.150-1.SE
I've got brand new 3945's with onboard 16-port 3560e switches. On the first power up I see that there are several new vlans added that appear to be default vlans..
vlan 2 name fst2
vlan 3 name fst3
vlan 4 name fst4
vlan 5 name fst5
vlan 6 name fst6
vlan 20 name VLAN0020
vlan 21 name VLAN0021
vlan 22 name VLAN0022
vlan 23 name VLAN0023
vlan 99 name VLAN0099
I deleted the vlan.dat and reloaded the switch but these vlans come back. What these vlans are intended for and is there a better way to get rid of them? What does "fst" stand for?
View 4 Replies
View Related
Jun 17, 2012
I implemented the 3560E switch, this one have two Giga bit ethernet/10-Gigabit Ethernet module slots. I used the Twin Gig Converter Modules and one SFP. All configuration was applied in the Ten Giga bit, however the interface giga bit ethernet is UP UP state and the Ten giga down down.
View 3 Replies
View Related
Apr 18, 2012
I am looking for a PoE switch with Routing capabilities (e.g osfp) something lower end than 3560E.
View 10 Replies
View Related
Dec 12, 2012
We have a 24 port and 48 port 3560 E switches with identical IOS the 48 port switch supports private vlan while 24 port switch doesnt
configure private vlans on 24 ports 3560e and is it best practise to configure private vlan on this platform(3560)?
IOS version : C3560E Software (C3560E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
flash:/c3560e-universalk9-mz.122-55.SE3/c3560e-universalk9-mz.122-55.SE3.bin
View 3 Replies
View Related
Nov 11, 2012
is it possible, to use a Catalyst Switch (in my case a 3560E) as a source for a console session to another Catalyst? In principle to use it as a console terminal server.
View 1 Replies
View Related
Mar 19, 2013
I am looking at upgrading my 6503-E switch. While I get the chance, I would like all aspects upgraded as I finally have some "downtime". I am running a Sup 720-3B.From what I understand, the boot image is a recovery image (mini IOS) - should the main IOS fail.Where should this be installed, sup-bootflash:/ or bootflash:/ ?,The file is “s72033-boot-mz.122-33.SXI11.bin.”The Boot Loader. My understanding is that Bootloaders are not used in these Sups with a MSFC3? I am not sure why TBH .. but would this be the case ?Rommon can be upgraded. I don’t quite understand if there are two ROMs (SP and RP).
View 1 Replies
View Related
Apr 4, 2013
I have a Catalyst 4510 that is running IOS version 15.X that has a bug and Cisco recommends upgrading the IOS. Are there additional steps required to perform an IOS upgrade due to licencing Cisco put in place?
View 5 Replies
View Related
Sep 10, 2012
i am facing an error while upgrading the IOS image on 3560 switch. [code]
View 1 Replies
View Related
Nov 27, 2012
a) I have three C3750-X switch stack together as my SAN switch and running on the new 15.0 release which is 15.0(1) SE.
b) Recently the master switch rebooted without any explanation. Create ticket with TAC and got an answer that it is due to a bug with ID: CSCtr31957.
My question is, which release that should i choose either the 15.0(1) SE3 or the latest 15.0(2)? Will it affect any of my configuration if i change to 15.0(2)?
Finally, what is the best practice to upgrade IOS in a stack whether to upgrade it 1 switch at a time or do it to all at once?
View 3 Replies
View Related
Nov 20, 2012
is there a document that explains the compatibility of 3750 series that can be stacked together? for example can we stack 3750-x with 3750-v2 without the power sharing? Can we stack a L3 3750 with L2 3750 without upgrading the L2 switch IOS to ip services?
View 8 Replies
View Related
Feb 19, 2013
I wan to migrate from a router 2800 to L3 switch 3750G , the thing is that we have several vlans and we use a router sometimes with each interface configure with correspoinding vlan subnet ip to route traffic between vlans there is no static or dynamic routing only directly connected interfaces on router routing traffic to each other ?How would i configure a L3 switch interface for simillar functionality , below is my current router configuration
!
ip domain name yourdomain.com
multilink bundle-name authenticated
!
vtp mode transparent
[code]...
View 15 Replies
View Related
Nov 8, 2011
I upgraded the newest IOS 15.0(1)SE for our SW C2960-24-TT-L, the process was succeseful. However, we found SW memory utilization raised to 82% this morning in normal situation. (Momery: Total 21341260, Used17471692) Did you guys meet the same problem after upgrading to 15.0(1)SE? I also would like to know what the normal memory utilization is? and what is the impact of memory utilization highly?
View 8 Replies
View Related
Apr 29, 2013
I am trying to copy IOS from my TFTP server which is on my laptop to cisco 2960 switch
I am able to ping to switch from my laptop, connectivity is fine, tftp server is running
Current Image on Switch --> C2960-LANBASE-MZ.122-25.SEE3.bin --> trying to upgrade to --> c2960-lanbasek9-mz.122-53.SE2
I am getting below error when trying to upgarde IOS:
2960-SW#copy tftp: flash:
Address or name of remote host []? 10.1.x.x
Source filename []? c2960-lanbasek9-mz.122-53.SE2
[Code].....
View 6 Replies
View Related
Jan 23, 2012
I was upgrading the newest software images on a c2950G switch. So i followed the step by step procedures from url...I removed the current flash that was on the switch and then for some reason typed reload. This started the switch up without the IOS. Make a long story short I am now stuck in switch: prompt mode and I am unable to use x-modem to transfer the newest IOS onto the switch. I am currently getting "no response remote system".
View 2 Replies
View Related
Feb 19, 2012
I have a few 3560E running Ver 12.2(50)se2. Can these boxes be configured to run VRF. I see a "sho IP VRF" option, but I do not see it available when under config t. Do I need to do a IOS upgrade to be able to configure VRF?
View 7 Replies
View Related
Sep 2, 2010
I upgraded four 3560E, 12.2(44) to 12.2(55)SEThree 3560 works fine, the last one stops after 17-18 seconds with a solid green LED. I cant get into ROMmon, the switch doesn't boot up. its like "dead but still alive"
My TS:
1: Removed all SFPs.
2: Reset PSU and fan modules.
3: Replace PSU and fan modules.
4: Try to get into ROMmon.(pushing mode button and break seq.)
Startup LED:0-1 seconds: SYST: Amber RPS: Amber STAT: Green DUPLEX: Green SPEED: Green
1-17 seconds SYST: Blinking Green RPS: OFF STAT: OFF DUPLEX: OFF SPEED: OFF
18 s--> (only testet up to one hour) SYST: Solid Green RPS: OFF STAT: OFF DUPLEX: OFF SPEED: OFF
A working 3560EStartup LED information. If I compare a working switch with the faulty switch I can see about 18 seconds into bootingSYST change very fast from green to amber and continues with booting,this doesnt happened on the faulty switch (solid green 18 seconds). Pushing MODE button, doesn't get me in to ROMmon, this works for all the other switches.On a normal 3560 it takes around 40 seconds before I get in to ROMmon. With this faulty switch it stops after 18 seconds(solid green) and it doesnt respond.
View 7 Replies
View Related
Nov 12, 2012
We have two Cisco 3560E layer 3 switches at the core of our network. The switches are configured as an HSRP pair and the clients on our network point to the HSRP address as their default gateway. So if CORE-A dies, then CORE-B will pick up the address and the default route for the clients will continue to be available.We also need to specify a few static routes on the core switch to allow us to get to specific networks. Is there a way to do this so that the routes failover in the same way that the default gateway does?
View 2 Replies
View Related
Feb 19, 2012
I have a 3560E with 2 vlans that I want to route between. one device with 2 vlans and route between.Interfaces are configured as such:
int g0/11
switchport mode access
switchport access vlan 10
int g0/12
switchport mode access
switchport access vlan 11
[code]...
Laptops on each port with 10.10.10.2 and 10.10.11.2 configured on them. I can ping from 10.10.10.2 to 10.10.11.1, but not to 10.10.11.2.What do I have to configure to be able to get the 2 laptops to talk to each other?
View 9 Replies
View Related
Mar 11, 2013
I have a cisco 3560E switch setup with LACP, when using LACP i receive alot of packet loss / output drops
When a ping from the server behind LACP:
--- google.com ping statistics ---
44 packets transmitted, 39 received, 11% packet loss, time 42990ms
what would cause this packet loss with lacp?
some output from the switch:
Port-channel12 is up, line protocol is up (connected)
Hardware is EtherChannel, address is d0d0.fd58.7390 (bia d0d0.fd58.7390)
Description: LACP-PORT
[Code]....
View 2 Replies
View Related
Sep 23, 2012
I'm trying to configure "IP PIM SPARSE-MODE" command on a vlan interface on a 3560E switch but it doesn't give me the option to do this. The only option available is ip pim passive. What would cause this ? On the same switch a physical interface is already configured with IP PIM SPARSE-MODE.
View 2 Replies
View Related
Apr 13, 2011
I have 3560e which doesn't appear to be passing igmp traffic to the upstream router
PC1 ----------- ASA ------------ PC2--------- 3560e ----------- 3825 -------------------- WAN --------------------- Router ------------- Server
My ASA runs SMR, has an igmp forward interface outside command on the inside and has a trunk port to the 3560e (V lans 32 & 48).PC2 is a test pc on the 3560e on vlan32. 3825 is my ISPs router on vlan32.
- if i try to access the stream from PC2 it works.
- if i try to access the stream from PC1, i see the igmp join leave my ASA onto the 3560E (i've captured on the 3560e's link to the ASA).
I've also captured on the ASA and i can see the igmp packet leave the outside interface but the join doesn't reach the 3825 (i've captured on the 3560e port facing the router and there is no join being forwarded).the switch is running in layer 2, 12.2(35r)SE1.
switch#sh ip igmp snooping querierVlan IP Address IGMP Version Port---------Switch#
Global IGMP Snooping configuration:------------------------IGMP snooping : EnabledIGMPv3 snooping (minimal) : Enabled Report suppression : Enabled TCN solicit query : Disabled TCN flood query count : 2Robustness variable : 2Last member query count : 2Last member query interval : 1000
View 2 Replies
View Related
Apr 15, 2012
We have a Site that is connected via Wireless Bridge to the Main Site, the site is on separate VLAN with Cisco 3560 switch. The main site has 6509 swith. Configuration as per attached diagram. We are connecting a fiber between the remote and the main site and adding a 3560E switch at the remote site, however we would like to keep the wireless connection as a backup in case the fiber is severed the wireless will be availble. Attached diagram shows detailed cofiguration. I would like to know what should I change to make this working. STP is enabled on all switches.
View 3 Replies
View Related
Dec 1, 2011
I need to know the key functional differences between the Catalyst switches 3560E, 3560X and 3560G.
View 1 Replies
View Related
Dec 6, 2011
We are receiving a large amount of output drops on 4 interfaces that connect to microwave wireless.This is playing up with our Management system. Saw a bug report but that was for 3750, not the IOS version but was a similar issue. [code] The output errors tend to happen at the same time. All ports are trunks however there are other trunks on the switch that are not having these issues. [code]
View 7 Replies
View Related
Jun 11, 2011
I try to configure in both Clean Access Manager and Switch 3560E-24Ps on SNMP Version 2 protocol but I can't make it working together (For CAM and Switch 3560G-48Ps I can do that). [code]
View 3 Replies
View Related
Apr 11, 2012
The have around 80 staff and I think the current infrastructure is overkill for the size of the company. The current kit is old and they have no GB ethernet ports. They currently have:-
Core Switch:
1x Cisco c6509with a 48 port fast ethernet module (WS-X6248-RJ-45)
and an 8 port fibre module (WS-X6408A-GBIC)
I'm looking to replace this with something with 72 ethernet ports and 8 fibre ports
Access Switches:
2x 3500Replacement needs at least 48 ports and 2 fibre modules each
and 2x 5500Replacement needs at least 72 ports and 2 fibre modules each.
View 13 Replies
View Related
Jan 31, 2013
I am in the process of upgrading our network switches and wondering if the .lic file will work with the new software or if I have to rehost for the move to 15.0. Its a remote site and I would like to get some solid info before I pull the trigger.
Also which IOS should I be upgrading to?
c3750e-ipbasek9-mz.150-2.SE.bin
or
c3750e-universalk9-mz.150-2.SE.bin
[Code].....
View 2 Replies
View Related
Jan 15, 2011
We want to upgrade the IOS from 15.0(1) to 15.1 for some reason. Here is the output of my router's "show ver":
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 28-Oct-10 18:32 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M9, RELEASE SOFTWARE
[code]....
We have enabled the technology package license "uc" in the previous version, would it be loss after the upgrade?
View 5 Replies
View Related
Jan 4, 2013
I am currently running a 4506 with a sup V engine. I have purchased a sup 7 engine. Is there a guide on how to perform this task. I am sure I need to do an IOS update as well.
View 2 Replies
View Related
Aug 30, 2012
we have two core swiches 6506 and around 55 cat 3550 switches. currently we are on the process of replacing the cat 3550 switches to 3750 switches.We need 10/1000/1000 speed, ip base image with upgrade options. Our up links from cat 3550s(sfps) are single mode and dual mode fiber mode with 1 gbps ports on core switch.
At present we are not upgrading to 10 gb modules on core. Spread over 15 floors each floor needs 2 up links(single mode , and dual mode). since cat 3750 sfps are smaller in size existing gibics cannot be used. Looking for the best option of cat 3750 switches with 1 gb up links which can be upgraded to 10 gb later when we replace the modle on core. Requirements:
1- Cat 3750 switches 55 in no with sfps for 1 gb up link (dual mode fiber and single mode fiber)
2- stacking option
3- 10/100/1000 speed
4- ip base image upgradable to ip service image
5- ipv6 compatibaility. Network is spread over 15 floors so from each floor we need two sfp up links 1 gbps using dual mode and single mode
-6-Should be upgradable to 10 gb in future when we upgrade the core modules
Or is it better to go for 10 gb module in core as well as edge switches ? if so what should be the modules?
View 13 Replies
View Related
