Cisco Switching/Routing :: Upgrading Newest Software Images On C2950G Switch
Jan 23, 2012
I was upgrading the newest software images on a c2950G switch. So i followed the step by step procedures from url...I removed the current flash that was on the switch and then for some reason typed reload. This started the switch up without the IOS. Make a long story short I am now stuck in switch: prompt mode and I am unable to use x-modem to transfer the newest IOS onto the switch. I am currently getting "no response remote system".
View 2 Replies
ADVERTISEMENT
Jan 18, 2012
I have been asked to upgrade the IOS images on three 4506 switches with a single Supervisor IV engine in each to allow for SSH2 access.The current image is cat4000-i5s-mz.122-25.EWA.bin..I have uploaded cat4000-i5k91s-mz.122-25.EWA14.bin to bootflash on each Supervisor engine.The ROM on each SUP IV is 12.1(20r). I don't want to have to upgrade the ROM version.Will the cat4000-i5k91s-mz.122-25.EWA14.bin image retain all the current features of the current image and provide SSH2 support, without requiring a ROM upgrade?Each switch has 512 Mb of RAM.If this image will accomplish what I want, what are the commands used to select the new image from bootflash. I'm familiar with image updates on fixed chassis switches using the boot system flash command.
View 2 Replies
View Related
Feb 9, 2012
I can't to connect on my switch (WS-C2950G-48-EI) with Telnet or HTTP.When to connect with console, i have a error [code]
View 4 Replies
View Related
Sep 30, 2012
We use C2950G switches with IOS 12.1(22)EA12 . Switches are set up to send logs to a server (informationnal level). On this server, we receive many of logs from those switches, but none about interfaces errors (even if interfaces statistics show interfaces errors). On C3548 switches it's work fine.How should I be sure the set up of switches is correct ? Why do I never receive messages as %LINK-4-ERROR:[char] is experiencing errors ?
View 2 Replies
View Related
Mar 19, 2013
I am looking at upgrading my 6503-E switch. While I get the chance, I would like all aspects upgraded as I finally have some "downtime". I am running a Sup 720-3B.From what I understand, the boot image is a recovery image (mini IOS) - should the main IOS fail.Where should this be installed, sup-bootflash:/ or bootflash:/ ?,The file is “s72033-boot-mz.122-33.SXI11.bin.”The Boot Loader. My understanding is that Bootloaders are not used in these Sups with a MSFC3? I am not sure why TBH .. but would this be the case ?Rommon can be upgraded. I don’t quite understand if there are two ROMs (SP and RP).
View 1 Replies
View Related
Apr 4, 2013
I have a Catalyst 4510 that is running IOS version 15.X that has a bug and Cisco recommends upgrading the IOS. Are there additional steps required to perform an IOS upgrade due to licencing Cisco put in place?
View 5 Replies
View Related
Sep 10, 2012
i am facing an error while upgrading the IOS image on 3560 switch. [code]
View 1 Replies
View Related
Nov 27, 2012
a) I have three C3750-X switch stack together as my SAN switch and running on the new 15.0 release which is 15.0(1) SE.
b) Recently the master switch rebooted without any explanation. Create ticket with TAC and got an answer that it is due to a bug with ID: CSCtr31957.
My question is, which release that should i choose either the 15.0(1) SE3 or the latest 15.0(2)? Will it affect any of my configuration if i change to 15.0(2)?
Finally, what is the best practice to upgrade IOS in a stack whether to upgrade it 1 switch at a time or do it to all at once?
View 3 Replies
View Related
Nov 20, 2012
is there a document that explains the compatibility of 3750 series that can be stacked together? for example can we stack 3750-x with 3750-v2 without the power sharing? Can we stack a L3 3750 with L2 3750 without upgrading the L2 switch IOS to ip services?
View 8 Replies
View Related
Feb 19, 2013
I wan to migrate from a router 2800 to L3 switch 3750G , the thing is that we have several vlans and we use a router sometimes with each interface configure with correspoinding vlan subnet ip to route traffic between vlans there is no static or dynamic routing only directly connected interfaces on router routing traffic to each other ?How would i configure a L3 switch interface for simillar functionality , below is my current router configuration
!
ip domain name yourdomain.com
multilink bundle-name authenticated
!
vtp mode transparent
[code]...
View 15 Replies
View Related
May 15, 2013
I recently upgraded a remote site of mine to IOS 15-2.SE ipbasek9 on 3 3560E series switches. On switch number 2 I have 5 VG224's running (vg224-i6k9s- m) 12.4(22)T3. After the switches reloaded the VG224's dropped their connection. After doing all basic troubleshooting I reloaded the 12.2 (58)SE2 ipbasek9 image back on to the 3560E's and the VG224's reconnected immediately after reload and all phones registered.
Is the problem a licensing issue with the 15.x IOS on the 3560's or do I need to upgrade the VG224's to IOS 15.x as well for them to connect and operate via the 3560e switch running 15-2?
View 1 Replies
View Related
Nov 8, 2011
I upgraded the newest IOS 15.0(1)SE for our SW C2960-24-TT-L, the process was succeseful. However, we found SW memory utilization raised to 82% this morning in normal situation. (Momery: Total 21341260, Used17471692) Did you guys meet the same problem after upgrading to 15.0(1)SE? I also would like to know what the normal memory utilization is? and what is the impact of memory utilization highly?
View 8 Replies
View Related
Apr 29, 2013
I am trying to copy IOS from my TFTP server which is on my laptop to cisco 2960 switch
I am able to ping to switch from my laptop, connectivity is fine, tftp server is running
Current Image on Switch --> C2960-LANBASE-MZ.122-25.SEE3.bin --> trying to upgrade to --> c2960-lanbasek9-mz.122-53.SE2
I am getting below error when trying to upgarde IOS:
2960-SW#copy tftp: flash:
Address or name of remote host []? 10.1.x.x
Source filename []? c2960-lanbasek9-mz.122-53.SE2
[Code].....
View 6 Replies
View Related
Apr 2, 2009
I have 1841, 2800 and 3800 routers and need to do IOS upgrade to all of them. Existing routers do not have enough flash to hold 2 IOS images.if the router has 12.4.13r ROM IOS, will I be able to boot the ISR router via Cisco brand USB? That means in case something goes wrong while I am uploading new IOS to the router via WAN and something wrong, now router in ROMMON mode. If a local site person has a Cisco USB with an IOS in it, can he just stick it to the router and reboot the router and router will go out of rommon and go into normal mode? After it is working, then I can put the running IOS onto the exisitng CF card so now I can remove the USB and the CF card has a good IOS and reboot the router again.I am just trying to find a safe way to upgrade the site when they don't have big enough flash to hold 2 IOS at the same time. The local person is not technical so asking him to setup tftp server and put the IOS in the computer and so I can do tftpdnld while in rommon mode to grab the IOS from his tftp will be difficult to have the local person to set it up.
If ISR can boot off of the IOS in USB only, then I assume the requiremetn is the ROM IOS needs to be 12.4.13r. Then what is a safe way to upgrade the ROM IOS to this then? I never upgrade ROM IOS before so don't know what kind of problem I may run into and whether it's higher risk to upgrade this than upgrading the regular ios? If it is, then all my routers won't have this ROM IOS version, so that means I can't use USB to boot then? Will that means I am down to tftp server option? ( I heard xmodem won't work as it will time out before the ios can load via the slow dialup link into the router to rescue it from rommon mode).
View 33 Replies
View Related
Apr 11, 2012
The have around 80 staff and I think the current infrastructure is overkill for the size of the company. The current kit is old and they have no GB ethernet ports. They currently have:-
Core Switch:
1x Cisco c6509with a 48 port fast ethernet module (WS-X6248-RJ-45)
and an 8 port fibre module (WS-X6408A-GBIC)
I'm looking to replace this with something with 72 ethernet ports and 8 fibre ports
Access Switches:
2x 3500Replacement needs at least 48 ports and 2 fibre modules each
and 2x 5500Replacement needs at least 72 ports and 2 fibre modules each.
View 13 Replies
View Related
Jan 31, 2013
I am in the process of upgrading our network switches and wondering if the .lic file will work with the new software or if I have to rehost for the move to 15.0. Its a remote site and I would like to get some solid info before I pull the trigger.
Also which IOS should I be upgrading to?
c3750e-ipbasek9-mz.150-2.SE.bin
or
c3750e-universalk9-mz.150-2.SE.bin
[Code].....
View 2 Replies
View Related
Jan 15, 2011
We want to upgrade the IOS from 15.0(1) to 15.1 for some reason. Here is the output of my router's "show ver":
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Thu 28-Oct-10 18:32 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M9, RELEASE SOFTWARE
[code]....
We have enabled the technology package license "uc" in the previous version, would it be loss after the upgrade?
View 5 Replies
View Related
Jan 4, 2013
I am currently running a 4506 with a sup V engine. I have purchased a sup 7 engine. Is there a guide on how to perform this task. I am sure I need to do an IOS update as well.
View 2 Replies
View Related
Aug 30, 2012
we have two core swiches 6506 and around 55 cat 3550 switches. currently we are on the process of replacing the cat 3550 switches to 3750 switches.We need 10/1000/1000 speed, ip base image with upgrade options. Our up links from cat 3550s(sfps) are single mode and dual mode fiber mode with 1 gbps ports on core switch.
At present we are not upgrading to 10 gb modules on core. Spread over 15 floors each floor needs 2 up links(single mode , and dual mode). since cat 3750 sfps are smaller in size existing gibics cannot be used. Looking for the best option of cat 3750 switches with 1 gb up links which can be upgraded to 10 gb later when we replace the modle on core. Requirements:
1- Cat 3750 switches 55 in no with sfps for 1 gb up link (dual mode fiber and single mode fiber)
2- stacking option
3- 10/100/1000 speed
4- ip base image upgradable to ip service image
5- ipv6 compatibaility. Network is spread over 15 floors so from each floor we need two sfp up links 1 gbps using dual mode and single mode
-6-Should be upgradable to 10 gb in future when we upgrade the core modules
Or is it better to go for 10 gb module in core as well as edge switches ? if so what should be the modules?
View 13 Replies
View Related
Jun 4, 2012
I am planning to upgrade my cat6500 using ISSU but can not find my doc to follow yet.
View 1 Replies
View Related
Apr 18, 2013
I am upgrading a Cisco 6506E VSS from 12.2(33)SXI5 to 12.2(33)SXJ5 during a maintenance window. So I have plenty of time to reboot the VSS. Confirm below is the correct procedure. I have manually copied the new IOS to both active and standby Sup720s.
no boot system
boot system flash sup-bootdisk:NEW_IOS.bin
boot system flash sup-bootdisk:OLD_IOS.bin
!
copy run start
reload
I was going through the below cisco document and there are a few more steps as below: Is it necessary?
[URL]
Router(config)# no boot system
View 2 Replies
View Related
Apr 29, 2012
I just need a little refreshing on upgrading a stack of 3750's. This stack only has 2 switches: [code]
1.) If I remember correctly I simply tftp the IOS to the flash of each switch and then reload the master only?
2.) Can I safely assume these are the 2 flash locations:
View 3 Replies
View Related
Apr 2, 2012
I had a strange problem here after upgrading Cisco 3750X.The upgrading was going smoothly, I copied a newer IOS to the flash from another Cisco 3750X through TFTP, changed the boot image.It took a while do to the microcode upgrading, finally, it started to boot up. But when it completes the boot up, I can't see the normal login prompt, but only some strange codes. From what I can see, it seems some decoding problem, as if I plug or unplug a cable from the switch, the strange code pops up again, like in normal situation, the console tells you that the interface is going up and down.
The original image of the switch: c3750e-universalk9-mz.122-53.SE2.bin
Upgrade to image: c3750e-universalk9-mz.122-55.SE3.bin
However, I don't have any problem to telnet to this switch, as it has correct IP address and login configured before the upgrading. I have reboot the switch for couple of times, reconnect to the serial port still doesn't show me anything.I am wonering has any one has met this situation before? detailed message shown after the boot up. cisco WS-C3750X-48 (PowerPC405) processor (revision A0) with 262144K bytes of memory.
Processor board ID FDO1449Z04L
Last reset from power-on
1 Virtual Ethernet interface
1 FastEthernet interface
52 Gigabit Ethernet interfaces
[Code] .....
View 3 Replies
View Related
Feb 20, 2012
I have a 4510R-E chassis which currently has a single supervisor 5 installed.
We are now looking at upgrading the supervisor to a Sup6. Now the question is this, can I install the Sup6 into the redundant cpu slot and then perform a failover to get the new switch working without any noticable downtime.
I'm not sure what having a Sup V and a Sup 6 in at the same time will do to the backplane.
Otherwise I have to take the switch down and then install the card and software manually.
View 2 Replies
View Related
Oct 12, 2012
It would be so easy but failed to upgrade 3560X switch to ip services licence is bought and paid for mail and log from the CLI and tftp server attached
View 17 Replies
View Related
Dec 3, 2012
way to upgrade the IOS in my stack on 4 3750x switches
View 6 Replies
View Related
Jan 16, 2013
Am attempting to load a new license on a 24 Port 3750X. Was LANBase code, need to get it to IPBase. Have the license file. Have put it on the flash drive. Running "license install flash:" i get the message "%Error reading flash: (is a directory)%Error: License installation failed with error: XML parsing failed"The license installation instructions are a bit cryptic so I could be messing it up. However, every variation I can think of is not working. The command listed above gets the most "promising" results.
View 1 Replies
View Related
Dec 28, 2012
It seems my 2960s and 3560s switches have enough flash space and memory to support the 15.0 IOS should I be OK to jump to this from 12.2(35)?
View 10 Replies
View Related
Feb 17, 2012
I have the following switch:
#show version
Cisco IOS Software, C3750 Software (C3750-IPSERVICES-M), Version 12.2(52)SE, RELEASE SOFTWARE (fc3)
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Image text-base: 0x01000000, data-base: 0x02C00000
ROM: Bootstrap program is C3750 boot loader
BOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.2(44)SE5, RELEASE SOFTWARE (fc1)
[code]...
I have downloaded c3750-ipservicesk9-mz.150-1.SE2.bin and I want to upgrade iOS to this image.
I have a few questions related to this:
1. Is my switch model compatible with this iOS version?
2. Do you recommend the upgrade? Does it bring some notable features?
3. Can I upgrade for free or do I need to buy some license?
4. I also want to upgrade/add the crypto image, can I add crypto for free or some license is required?
5. I have remote access to my switch via the console cable which plugged into machine1. But machine1 is connected to network via the same switch. I am accessing machine1 via SSH, and then the switch via console cable (minicom on CentOS). Is there an upgrade procedure for this kind of situation that also has some fall back (like reboot in X minutes and load the previous image) if the upgrade goes wrong?
View 6 Replies
View Related
Apr 25, 2012
I purchased several Cisco 2811 with Advanced IP Services - they are version 12.2.X
The product number looked like this
CISCO2811-HSEC/K9 2811 Bundle w/AIM-VPN/SSL-2,Adv IP Serv,10 SSL lic,128F/512D
I need to upgrade the IOS to version 15.1 - Do I require a license ? What happens if I install it without a License ? Am I entitled to a free license as I am not changing the software type (ADV IP Serv) ?
View 2 Replies
View Related
Jan 10, 2012
I have a customer who has a Cisco 2821 router with software 2821/HSEC/K9 and they wish to upgrade to C2821-VSEC-SRST/K9.From my understanding they want to use the same router but install an IOS with the capabilites it has at the moment but with voice. [code]How do I go about pricing this up and what upgrade sku's will do this?I am not to worried about the memory.Is it just a simple ios upgrade as the srst licenses are on a trust basis?
View 2 Replies
View Related
Nov 3, 2011
I have an older 4006 with a Supervisor II+. We now need OSPF support, which the Sup II+ does not provide. I have access to a Supervisor III (WS-X4014), which will provide OSPF support. Question is, are there any gotchas to shutting down the switch, replacing Supervisor Engines and then powering up? What about the flash card? On my current system, it appears that I am only using bootflash: , which is where the IOS resides (see below). Since my startup config is in nvram and my IOS is in bootflash, what's the purpose of the flash card in slot0: ? and where does NVRAM and bootflash actually live on a 4006 ( on the Supervisor Engine?)
sh bootvar
BOOT variable = bootflash:cat4500-ipbase-mz.122-31.SGA11.bin,1;,1;
CONFIG_FILE variable does not exist
BOOTLDR variable does not exist
[Code].....
View 5 Replies
View Related
Nov 9, 2011
I have cisco 3750 with ipservices license and I am running with c3750e-universal-mz.122-50.SE2. And I would like to upgrade the IOS " k9" IOS. ie c3750e-universalk9-mz.122-50.SE2. Is there any license required for that ?Also any difference in the IOS upgrade procedure.
View 1 Replies
View Related
