Cisco Switching/Routing :: New Default Vlans On 3560e Switch
Nov 2, 2011
3945 is running c3900e-universalk9-mz.SPA.151-4.M2
3560e is running c3560e-universalk9-mz.150-1.SE
I've got brand new 3945's with onboard 16-port 3560e switches. On the first power up I see that there are several new vlans added that appear to be default vlans..
vlan 2 name fst2
vlan 3 name fst3
vlan 4 name fst4
vlan 5 name fst5
vlan 6 name fst6
vlan 20 name VLAN0020
vlan 21 name VLAN0021
vlan 22 name VLAN0022
vlan 23 name VLAN0023
vlan 99 name VLAN0099
I deleted the vlan.dat and reloaded the switch but these vlans come back. What these vlans are intended for and is there a better way to get rid of them? What does "fst" stand for?
View 4 Replies
ADVERTISEMENT
Feb 19, 2012
I have a 3560E with 2 vlans that I want to route between. one device with 2 vlans and route between.Interfaces are configured as such:
int g0/11
switchport mode access
switchport access vlan 10
int g0/12
switchport mode access
switchport access vlan 11
[code]...
Laptops on each port with 10.10.10.2 and 10.10.11.2 configured on them. I can ping from 10.10.10.2 to 10.10.11.1, but not to 10.10.11.2.What do I have to configure to be able to get the 2 laptops to talk to each other?
View 9 Replies
View Related
Apr 23, 2012
I need 10gigbit uplink for this switch. What are the other devices that i need order along with this device.And what is the diff between X2-10GB-LR= and CVR-X2-SFP.if i take CVR-X2-SFP, in future how can i upgrade from one gig to 10 gig?for current use i need 10gig support required. so what are all the other devices that i need to order.Fiber multimode and distance 15Mt only.
View 2 Replies
View Related
Jan 27, 2012
recently a Cisco 3560E switch went down due to a power surge. the switch is getting power but i am only seeing the below message continously. it is keep on rebooting. i try to reset to factory settings/ safe boot nothing worked. is there any way i can bring the switch up or it is hardware failure.Using driver version 1 for media type 2Base ethernet MAC Address: 00:23:33:af:1b:00Xmodem file system is available.The password-recovery mechanism is enabled.Using driver version 1 for media type 2Base ethernet MAC Address: 00:23:33:af:1b:00Xmodem file system is available.The password-recovery mechanism is enabled.
View 5 Replies
View Related
Jun 17, 2012
I implemented the 3560E switch, this one have two Giga bit ethernet/10-Gigabit Ethernet module slots. I used the Twin Gig Converter Modules and one SFP. All configuration was applied in the Ten Giga bit, however the interface giga bit ethernet is UP UP state and the Ten giga down down.
View 3 Replies
View Related
Apr 18, 2012
I am looking for a PoE switch with Routing capabilities (e.g osfp) something lower end than 3560E.
View 10 Replies
View Related
May 15, 2013
I recently upgraded a remote site of mine to IOS 15-2.SE ipbasek9 on 3 3560E series switches. On switch number 2 I have 5 VG224's running (vg224-i6k9s- m) 12.4(22)T3. After the switches reloaded the VG224's dropped their connection. After doing all basic troubleshooting I reloaded the 12.2 (58)SE2 ipbasek9 image back on to the 3560E's and the VG224's reconnected immediately after reload and all phones registered.
Is the problem a licensing issue with the 15.x IOS on the 3560's or do I need to upgrade the VG224's to IOS 15.x as well for them to connect and operate via the 3560e switch running 15-2?
View 1 Replies
View Related
Dec 12, 2012
We have a 24 port and 48 port 3560 E switches with identical IOS the 48 port switch supports private vlan while 24 port switch doesnt
configure private vlans on 24 ports 3560e and is it best practise to configure private vlan on this platform(3560)?
IOS version : C3560E Software (C3560E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
flash:/c3560e-universalk9-mz.122-55.SE3/c3560e-universalk9-mz.122-55.SE3.bin
View 3 Replies
View Related
Nov 11, 2012
is it possible, to use a Catalyst Switch (in my case a 3560E) as a source for a console session to another Catalyst? In principle to use it as a console terminal server.
View 1 Replies
View Related
Oct 14, 2012
I am using a catalyst 2970 switch for 2 vlans. Corporate data and a separate VLAN for backups. What I want to do is create an LACP etherchannel to the switch and also trunk these ports so the server is part of both VLANS.Due to fact that some of these servers are on totally separated networks, they really shouldn't be able to talk to the backup server. Creating the VLAN for backups works to achieve this. I plan to create inbound ACLs on each port to allow only the ports and IPs for the backup network and allow everything we need for corporate data.I read somewhere that you can't have ACLs on an etherchannel and I just want to get it all straightened out. I notice I can't add an access group to the port-channel itself but I can on the port- channel member ports. Is this all I need to do or does this not work?
View 1 Replies
View Related
Nov 8, 2011
I'm trying to setup a port on a catalyst 3750 so it will pass traffic for 2 vlans. It connects to a (watchguard) firewall which I've configured with a primary IP (for vlan 27) and a secondary IP (for vlan 29).
However I can't seem to find the correct commands to enter on the cisco switch port (I've tried a variety).
FYI the current configuration is...
interface FastEthernet1/0/38
description ## Connection to WG vlan27 and vlan 29 ##
switchport trunk encapsulation dot1q
[Code].....
View 8 Replies
View Related
Jun 13, 2013
I have 6500 with this STP configuration:
spanning-tree mode rapid-pvst
no spanning-tree vlan 1-4094
I need to enable STP on vlan 100 and vlan 103.
When I do "spanning-tree vlan 100,103 root primary" and then "show spanning-tree".I see that STP is not enable on these vlans (100,103).
I tried to do "no spanning-tree vlan 1-99,101,102,104-4094" and it is not work.
There is a way to enable STP on vlans 100,103 without to do "spanning-tree vlan 1-4094"
View 1 Replies
View Related
Feb 22, 2012
I have a small cisco switch cluster (seven different 2924, 3524cisco switches) with 3550 as a cluster control which does all the inter vlan routing that works fine.
This cluster is in semi production PBX interop testing lab. This is a closed network without internet access and not connected to our corporate network.However now I have to add this capability so some equipment in the lab can get Microsoft updates over the internet.
I've created a port on a 3550 (fa0/19) and connected it to another network that has internet access. It picked an ip address and when I'm logged in to the 3550 I can ping hosts on the outside network. However I can't ping any hosts on that network from any hosts that are connected to my vlans.I've tried a few different things, but still can't make it to work.
Here is a short version of my 3550 configuration:
!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log datetime
no service password-encryption
[code]....
View 13 Replies
View Related
Feb 20, 2013
Is it possible to configure both Catalyst WS-C2960-24PC-L and Switch Cisco SG300-28 to work together for VLANs for voice and data ? If yes, can you give me the resources which I can refer to ?
View 4 Replies
View Related
Feb 20, 2012
We have a network of 30 VLANS and currently all the vlans have access to everything. We are using Cisco 6509 switch for Layer3 routing.I would like to prevent some VLANs accessing the server VLANs. How can I restrict access to the server VLANs?Do i need to implement access-lists on the 6500 switch? or do i need to create VLANS on the firewall so that all traffic i filtered ?
View 9 Replies
View Related
Nov 22, 2011
I am confused on how acl's respond on normal cisco switch (eg.6500) when applied on respective vlans. this is my scenario:on a 6506, i have 2 main vlans in question: Vlan 100 ( vendor1 - 172.16.100.0/24 ) & Vlan 200 ( vendor2 - 172.16.200.0/24 ). the requirement is,
- vendor1 should be able to access/ping vendor2 end points
- vendor2 should not be able to access/ping vendor1 end points
Now, if i ping from a host 172.16.100.11 in vlan 100 to another host 172.16.200.21 in vlan 200, will i be able to get a successful response ?
View 4 Replies
View Related
Dec 23, 2012
I just received a Catalyst 2960-C (WS-C2960C-8TC-L R) switch and I am unable to sign into its web GUI in order to configure it. I've tried both the Cisco Network Assistant and Internet Explorer and I am unable to log in either way. The documentation provided by Cisco states that the default password is simply cisco and that a username is unnecessary. Needless to say, it doesn't work. I've also Googled for other default passwords (such as cisco-cisco as the username-password), none of which worked either. I've also tried resetting the switch back to its factory default a few times.
View 8 Replies
View Related
Feb 19, 2012
I have a few 3560E running Ver 12.2(50)se2. Can these boxes be configured to run VRF. I see a "sho IP VRF" option, but I do not see it available when under config t. Do I need to do a IOS upgrade to be able to configure VRF?
View 7 Replies
View Related
Sep 2, 2010
I upgraded four 3560E, 12.2(44) to 12.2(55)SEThree 3560 works fine, the last one stops after 17-18 seconds with a solid green LED. I cant get into ROMmon, the switch doesn't boot up. its like "dead but still alive"
My TS:
1: Removed all SFPs.
2: Reset PSU and fan modules.
3: Replace PSU and fan modules.
4: Try to get into ROMmon.(pushing mode button and break seq.)
Startup LED:0-1 seconds: SYST: Amber RPS: Amber STAT: Green DUPLEX: Green SPEED: Green
1-17 seconds SYST: Blinking Green RPS: OFF STAT: OFF DUPLEX: OFF SPEED: OFF
18 s--> (only testet up to one hour) SYST: Solid Green RPS: OFF STAT: OFF DUPLEX: OFF SPEED: OFF
A working 3560EStartup LED information. If I compare a working switch with the faulty switch I can see about 18 seconds into bootingSYST change very fast from green to amber and continues with booting,this doesnt happened on the faulty switch (solid green 18 seconds). Pushing MODE button, doesn't get me in to ROMmon, this works for all the other switches.On a normal 3560 it takes around 40 seconds before I get in to ROMmon. With this faulty switch it stops after 18 seconds(solid green) and it doesnt respond.
View 7 Replies
View Related
Apr 7, 2012
My problem is that I have a Cisco 300 series small business switch with multiple VLANS each one with an IP address and two or three ports assigned to each VLAN. I have an E3200 wireless router that I want to use to use to share internet on the switch. All of the VLANs are reachable from the other VLANs and I've put a static route on the E3200 so that I can reach the VLANs from a machine connected only to the router. But I can't reach machines on the otherside of the router or get to the internet from the switch.
View 3 Replies
View Related
Nov 12, 2012
We have two Cisco 3560E layer 3 switches at the core of our network. The switches are configured as an HSRP pair and the clients on our network point to the HSRP address as their default gateway. So if CORE-A dies, then CORE-B will pick up the address and the default route for the clients will continue to be available.We also need to specify a few static routes on the core switch to allow us to get to specific networks. Is there a way to do this so that the routes failover in the same way that the default gateway does?
View 2 Replies
View Related
Aug 25, 2012
I had setup a lan infrastructure with 5 3750 stack swithes. In these 3 of them are in one stack which is acting as access switch, 2 of them in another stack which is as core switch where all the SVI is configured. Now, when i tried to ping from our edge pc which is connected in access switch to default gaeway, which is configured in core switch, the ICMP is getting delayed . But when try to ping from the same edge pc to another user PC, it is getting less tahn 1 millisecond icmp replies.
why icmp is delaying to default gateway , but working with another edge to edge pcs without any delays?
View 1 Replies
View Related
Oct 31, 2012
i have a stack of 3750x, with minimal configuration. there are two vlans, and two vlan interfaces with IP addresses. when i ping out from this switch to another host, it picks vlan1's ip address as the source automatically. i tested this by doing two pings with extended options using each vlan's interface as the source, and got different results. how the switch decided to use the first vlan's ip address as a source.
View 11 Replies
View Related
Aug 14, 2012
4500 switch is connected to 2960 switch.
4500 config
Vlan 10
name Data
It has ip helper configured that points to DHCP.From 4500 switch port - port x connects to 2960 port.Port x is configured as trunk between 4500 and 2960.
2960 config
vlan 10
name data
All user ports are configured under vlan 10 and as access ports.Port x is trunk port connected frpm 2960 to 4500 switch allowing vlan 1 and 10 only.This switch has no default gateway configured.
We connected user PC on 2960 switchports and they were able to get the IP from DHCP server and were able to access the network? My question is how users on 2960 switch are able to access the network without ip default-gateway configured on 2960 switch?
View 6 Replies
View Related
Mar 11, 2013
I have a cisco 3560E switch setup with LACP, when using LACP i receive alot of packet loss / output drops
When a ping from the server behind LACP:
--- google.com ping statistics ---
44 packets transmitted, 39 received, 11% packet loss, time 42990ms
what would cause this packet loss with lacp?
some output from the switch:
Port-channel12 is up, line protocol is up (connected)
Hardware is EtherChannel, address is d0d0.fd58.7390 (bia d0d0.fd58.7390)
Description: LACP-PORT
[Code]....
View 2 Replies
View Related
Sep 23, 2012
I'm trying to configure "IP PIM SPARSE-MODE" command on a vlan interface on a 3560E switch but it doesn't give me the option to do this. The only option available is ip pim passive. What would cause this ? On the same switch a physical interface is already configured with IP PIM SPARSE-MODE.
View 2 Replies
View Related
Apr 13, 2011
I have 3560e which doesn't appear to be passing igmp traffic to the upstream router
PC1 ----------- ASA ------------ PC2--------- 3560e ----------- 3825 -------------------- WAN --------------------- Router ------------- Server
My ASA runs SMR, has an igmp forward interface outside command on the inside and has a trunk port to the 3560e (V lans 32 & 48).PC2 is a test pc on the 3560e on vlan32. 3825 is my ISPs router on vlan32.
- if i try to access the stream from PC2 it works.
- if i try to access the stream from PC1, i see the igmp join leave my ASA onto the 3560E (i've captured on the 3560e's link to the ASA).
I've also captured on the ASA and i can see the igmp packet leave the outside interface but the join doesn't reach the 3825 (i've captured on the 3560e port facing the router and there is no join being forwarded).the switch is running in layer 2, 12.2(35r)SE1.
switch#sh ip igmp snooping querierVlan IP Address IGMP Version Port---------Switch#
Global IGMP Snooping configuration:------------------------IGMP snooping : EnabledIGMPv3 snooping (minimal) : Enabled Report suppression : Enabled TCN solicit query : Disabled TCN flood query count : 2Robustness variable : 2Last member query count : 2Last member query interval : 1000
View 2 Replies
View Related
Apr 15, 2012
We have a Site that is connected via Wireless Bridge to the Main Site, the site is on separate VLAN with Cisco 3560 switch. The main site has 6509 swith. Configuration as per attached diagram. We are connecting a fiber between the remote and the main site and adding a 3560E switch at the remote site, however we would like to keep the wireless connection as a backup in case the fiber is severed the wireless will be availble. Attached diagram shows detailed cofiguration. I would like to know what should I change to make this working. STP is enabled on all switches.
View 3 Replies
View Related
Dec 1, 2011
I need to know the key functional differences between the Catalyst switches 3560E, 3560X and 3560G.
View 1 Replies
View Related
Dec 6, 2011
We are receiving a large amount of output drops on 4 interfaces that connect to microwave wireless.This is playing up with our Management system. Saw a bug report but that was for 3750, not the IOS version but was a similar issue. [code] The output errors tend to happen at the same time. All ports are trunks however there are other trunks on the switch that are not having these issues. [code]
View 7 Replies
View Related
Mar 9, 2010
Is it possible to have multiple dhcp pools for multiple VLANs? The switch is a 6509 and/or 4506 catalyst. I don't want to use server-based products.
View 5 Replies
View Related
Jun 11, 2011
I try to configure in both Clean Access Manager and Switch 3560E-24Ps on SNMP Version 2 protocol but I can't make it working together (For CAM and Switch 3560G-48Ps I can do that). [code]
View 3 Replies
View Related
Oct 22, 2011
I've seen lots of posts from people having problems routing traffic between two vlans with some complicated examples. Any simple step-by-step example for an SG300 switch (in layer 3 mode) to configure two vlans and sending traffic between the two vlans without an external router?
-VLAN1 10.10.10.0
-VLAN2 10.10.20.0
I've tried to do this through the GUI and can't seem to make it work. I'm missing something in the GUI.
View 6 Replies
View Related
