Linksys Wireless Router :: Can't Find Wireless Printer With E2000
Sep 5, 2011
I have a Dell Inspiron 1720 (running Vista Home Premium) that connects to my Linksys E2000 and to a wireless printer, the Canon MX870. It's been working for months without problems.
I just got a Toshiba Satellite P770-BT4G22 Laptop (running Window 7 Professional 64 bit) and installed the Cisco Connect software following the instructions where you have already set up the router and just need to install the software to do things like add a device. I can connect to the router fine using a web browser or the Cisco Connect Software and my Toshiba connects to the Internet through the router without problems.
The problem is Cisco Connect says it can't find a wireless printer when I run it on my new Toshiba. I've put the printer within 3 feet of the router with my Toshiba in between but still it can't find it. My Dell in another room connects to the printer no problem. And I can print to the Canon if I select the Shared Canon Printer ( on the Dell) using the Toshiba's Control Panel Add Printer function. But obviously that means the Dell has to be on so that's not good for much more than troubleshooting. I've also wired a connection from the printer to the Toshiba and downloaded the latest driver, printed that way so I know that's not the problem. The problem is that Cisco Connect can't find the printer. It says there are 6 devices attached to my router so it's seeing something, but I guess not the printer. I've turned any firewalls off for this testing too.
I'm stumped as to why it can't find the printer when the Dell did and they are all on the same network. Unless it's not compatible with 64 bit Windows.
View 7 Replies
ADVERTISEMENT
Oct 2, 2011
We bought our Linksys E2000 in the summer and went to set it up but something came up... Now we are trying to set it up but cannot find our WPA key... Where can we find this?
View 2 Replies
View Related
Jul 13, 2012
Can't find client device for E2000
View 1 Replies
View Related
Aug 14, 2012
I have a Linksys E2000 router. I am trying to install an Epson NX230 printer on my home network. Apparently, the Epson printer has a MAC address assigned to it. My network cannot find the printer. I looked at my riuter setup and the MAC Address Clone has two buttons, Enabled Disabled. The Disabled button is clicked on. Accdording to documentation I foudn on this website, it looks like I can Enabled the MAC Address clone button. The document also mentgioend entereding the MAC address for a PC.
If I enable the MAC Address Clone, do I enter the MAC address for the printer or during the install process does the MAC address get installed also
View 9 Replies
View Related
Jun 10, 2011
I've got a Linksys E2000 router and a Brother MFC-7840W wireless printer and they don't seem to want to play nice together. The set-up process was fine and I can usually print wireless without a problem, but every so often I'll try to print and my computer will say that the printer is offline. Other computers on my network also show it as offline. The printer confirms it has an IP address, but even after power cycling it won't be picked up by my machines. I've even tried a full reset of the printer and re-configured it, at which point it is able to successfully obtain an IP address, but it still shows as offline on my PCs.
The only solution I have found is to powercycle the router. This always works. Now that's not a terribly inconvenient workaround most of the time, so I've been doing that for a few months now. It obviously implicates the router as the point of failure, but wireless internet access is not affected when the printer appears to be offline, so obviously some packets are getting through normally.
View 3 Replies
View Related
Aug 28, 2011
I bought a Sonos multiroom-system, and connected the first player to my E2000 router through Ethernet. It then gets a dynamic address through DHCP, I can see the Sonos within the network when looking in the admin tool of the router.When I start the Sonos controller software on my PC (XP), the software can not find the Sonos when my PC is connected through Wifi.As soon as I connect PC to the router with ethernet cable the Sonos is found immediately and can be initialised. After that, I can disconnect the cable and control the Sonos wirelessly. (as long as I don't close down the controller software for too long)
From what I understood from the sonos.com website, the Sonos sends an UPnP multicast signal on port for SSDP on port 1900 for initial connection. Further communications port are described below.Somehow, this multicast package seems not to be transferred into the wireless LAN, only into the wired LAN. Do I have to open some ports, filter some ports?Forward them?
View 2 Replies
View Related
Sep 1, 2012
I just set up a new EA3500. I added my HP Photosmart C4680 printer, however, my computer can not find. In other words, the router could see it to add it, but my computer can not find the printer at the router. MacBook Pro OS 10.6.8
View 3 Replies
View Related
Jan 6, 2011
Our office is set up with one desk top and at least two (occasional) laptops, one HP C6180 'all-in-one ' printer, and a Cisco Linksys E2000 router. Internet access for all computers seems OK, but printer seems to only print from one computer, and is inconsistant as to which one it will be. Have tried to shut down then restart printer. Have tried to disconnect and reconnect router, sometimes works, sometimes doesn't.
View 1 Replies
View Related
Sep 13, 2011
I just bought a refurbished E2000 wireless-n router with 1 Gb LAN ports (from Cisco online).This router is meant to replace my Netgear wireless-n router that only have 100 Mb LAN ports.I have 10 devices in my home network, 6 of them are using wireless (1 'g' and 5 'n') and 4 are interconnected with cat5e cables (trough the router).The devices have some different operating systems and their network adapters are from different brands.When I set up the Netgear router I didn't have to adjust anything for the wireless network to work fine.All wireless-n devices worked at 150 Mbps (sometimes going down shortly to 130 Mbps).The wireless-g device worked at 54 Mbps.For the last 2 days I've been trying to set up the E2000 to achieve a wireless-n speed higher then 72 Mpbs... without success.I tried all the suggestions that I found in the Cisco Knowledge Base.
- Upgrading the firmware to the latest version
- Trying different channels and channel widths
- Different wireless security methods and many others.
Also trying different settings on the different devices doesn't work.Changing the distance between router and devices as well as changing the location of the router don't affect the results.Switching on only 1 device at a time doesn't change anything either.It looks like the E2000 is set to not transmit on a higher speed than 72 Mbps, when it's actually supposed to achieve a wireless-n speed of up to 300 Mbps. I would be lucky if I get the half of it, but not if it's only one fourth.
View 3 Replies
View Related
Jan 27, 2012
I would like to set the router's dns entries but I don't see how to do that. Basic setup page has DNS setep for the DHCP scope but I don't want to push dns to my pc's. What I am looking to do is to use an alternate dns to what my service provder pushes and still have the abliity to route on my internal network.
View 1 Replies
View Related
Jan 28, 2012
So i can only forward 10 ports on my E2000.Example, one game (Battlefield 3) requires 10 ports (TCP and UDP combined).What about my other games? how can one, if possible, add more ports to the router?
View 4 Replies
View Related
Nov 3, 2011
E2000. I run the setup program, my laptop sees the router and it shows a strong signal. When I try to connect with it, it won't connect.
View 9 Replies
View Related
May 28, 2012
I've been looking around like a madman now in the settings. where can I turn off my WPS ? Just cracked my own PIN within 6 hours with Reaver.
View 9 Replies
View Related
Apr 24, 2011
My internet cut out last week and after calling my ISP I found out it was in fact my router that was causing the problem (regular connection to PPOE works fine). I've only had my E2000 about 2-3 months and have not had any problems with it. I've restarted the router, done a factory reset, upgraded the firmware, renewed the IP and still I cannot get any connectivity. I can access the router UI fine and I get a response from pinging it and also I have tried replacing the cables but that didn't fix the problem either.
View 9 Replies
View Related
Aug 28, 2011
I have an E2000 that I was given as a gift. I would like to use at it my office for a switch at my cubicle where I can connect 2-3 computers simultaneously. I am in a large network and am a user only. When I hooked the E2000 up today my computers would not get internet access BUT my laptop got wireless access and internet.
View 2 Replies
View Related
Dec 7, 2011
I'm using E2000 currently and meet a wireless connection problem. The speed can up to 300M bps. When I confiured the E2000 to band auto (20-40mhz) and my wireless network card to work at also auto (20-40) mode, it always down to 144M speed when connection.
If I changed some settings in E2000's wireless configuration, in the status sheet I can see it works at 40MHZ. But after a while,(5-10 mins) it automaticly down to 20MHZ and my labtop connect only got a 144M speed.
how can I deal with that to make it always keep at 300M connection? Note the previous router I used to connect to my lattop can always keep that speed.
View 2 Replies
View Related
Aug 21, 2011
I can connect to my router but either way it seems like i can't get any internet access (both wireless and by cable): url...I have tried the steps that the linksys FAQ suggests shall fix this problem, but this has not worked. I have also tried to reset the router without any luck. I know it its not the modem that is causing the problem because I'm wired to it now.On the E2000 every light is blinking as it should be (hence the FAQ) so it indicates that there might be a problem with the connection between the router and the computer (tested on other computers too without success).
View 9 Replies
View Related
Nov 14, 2011
I have a E2000 router that would go out and I would have to unplug and replug in every once in a while. Finally it just stopped working completely. I reset the router and now it won't let me connect. I have followed advice given to soembody else on here and went into router settings and cloned the mac, the IP address was there and reset my security settings. It let me connect to the network but not the internet...
View 2 Replies
View Related
Apr 21, 2013
I have a Linksys E2000.
It worked fine until one day, without any change at all, it simply stoped working. I mean, I can still connect through my wifi laptop connection (it shows connected to my router and says that I have an excelent signal). But, I can't reach the internet. But, If I unplug the internet cable, and plug it in my laptop, the connection works fine. A friend told me that this could be caused intentionally by the internet provider, that they would block my signal to avoid me using a wireless router, trying to force consumers to sign their own wireless service. Thus, by this friend advice, I've cloned my laptop's MAC address to the router. It didn't work either.
View 4 Replies
View Related
Sep 7, 2012
I have a Cisco E2000. When i connect to my cable modem directly, I get 30-35 MBps down and about 10 up. When I plug in to my E2000 it does that at first... but slowly over time, the speed degrades, usually down to about 5-6 down and 3-4 up. If I unplug the router, it typically restores full speed, but not for long (a few days maybe). Also, when I unplug the router, it is pretty hot.
View 4 Replies
View Related
Nov 11, 2011
For Xbox 360? currently, whether wired or wireless, my Xbox 360's NAT type is strict, and I am unable to do anything online whatsoever. Is there anyways to set up an exception, or anything that can open my Xbox's connection to my router so I can actually use it online?
View 2 Replies
View Related
Oct 28, 2011
Im using a linksys e 2000
Is there a way to block more than 4 websites, and 4 keywords?
View 4 Replies
View Related
Nov 11, 2011
I have an E2000 router that has an intermittent issue where Bonjour drops out. Suddenly my Apple TV won't see my computers, and my iPad won't see my network printer. This happens whether the Apple TV and computers are connected via wired or wireless interfaces.
Restarting the devices does not solve the issue.
Restarting the router solves the issue (until it happens again...)
My router is version 1.0, with 1.0.04 firmware.
View 3 Replies
View Related
Jul 11, 2011
I have a e2000 router and a wmp600n wireless card in my desktop pc. Everything works fine until I enable 40 mhz for faster speeds in the e2000 router. When I do this the router switches from 20 mhz to 40 mhz and I get the faster speed. But the effect of this is that my pc gets all "choppy". What I mean is that everything freezes up every few sec. For example when im minimizing windows, the windows freeze half way for about a sec then unfreezes. My mouse does the same thing, even my sound is choppy. I have to switch my router back to 20 mhz and then everything is fine again.
Using windows 7 64 bit
Using newest dirvers and firmware from Linksys.
View 4 Replies
View Related
Jan 31, 2012
I have a E2000 for a half a year now.We have been on hollyday for 5 days so my routers has been shutdown.Today it happend 3 times that my complete LAN disconnected for no reasonI didn't have any wired or wireless connection.
View 5 Replies
View Related
Jul 2, 2011
I have the Linksys E2000 and set it up on MacBookPro no problems. My iPhone 3G and my gf's iPhone4 connect no problem. Also, I have an XBox 360 connected via ethernet cable. Her MacBook however is constantly not getting an IP. I set her up with an EZ Key, but every time she connects we have to go through the EZ key process where I run Cisco Connect from my laptop. Why can't she just log in every time? This is frustrating me as all other aspects of this router work fine. I had her plugged into it as well with no problems. Again, it works after a dual computer Cisco Connect cycle, but my computer isn't always home.
View 1 Replies
View Related
Sep 20, 2011
For some reason my new E2000 will not connect to our Charter TV Cable internet service. Another router works fine with same cabling. I have reset EVERYTHING numerous times and cross patched -- hard patched, wireless to where my finers are bleeding. My ISP is DHCP and requires no login. So my router is set to automatically connect. Could the router be defective?
View 1 Replies
View Related
Nov 12, 2011
I got a refurbished E2000 on Amazon. Last night I set it up and when I tried accessing this website [URL], I could not connect to the server. First I thought it's the server problem and let it go. This morning it's the same probelm. I called my local cable technician and he told me it's the wifi router is blocking the website. I called the CISCO guys and they refused as it was out of warranty.
View 2 Replies
View Related
Aug 27, 2012
I want to set up another wireless laptop to access my e2000 but i dont remember the network key, How can I retirieve the key? through cisco connect maybe?
View 1 Replies
View Related
Jan 18, 2012
E2000-RM router has been working fine until about 2 days ago. Wired connection still works fine, but the wireless signals seems to be dropping in and out. I have a couple wireless devices and they all seem to be experiencing problems. Using the network connection bar on my laptop sometimes it shows a strong signal and connects no problem. Then all of a sudden the signal is gone (drops off list). It can be both the main and guest signal dropping, other times it might just be the main, etc., etc. Sometimes it shows a signal but will not connect and then a few seconds it might connect, or drop entirely. I guess the best word to describe it is highly erratic. Distance does not seem to matter. I can be 2 feet away and get the same behavior. The indicator on the box shows a signal at all times.
View 8 Replies
View Related
Jan 11, 2012
I have new PC with Window 7 and trying to set up E2000 on new computer with original set up CD. States I need go back to my old computer and set up new key and transfer to new computer. I do not have access to old computer. getting set up on new computer?
View 3 Replies
View Related
Jan 25, 2012
my internet connection cuts in and out so my computer cant connect to the router and it wont show up. I am on a windows 7 toshiba laptop and i have comcast as my internet service provider.
View 1 Replies
View Related
Oct 6, 2011
After a recent lighting strick close by I can not connect to the internet through my router. Stright from the modem works fine. The port light on the router does not come on. I rebooted modem, router and computer with no luck. It's like I've lost my network adapters and I don't know how to get them back. I tryed another E2000 and it's the same way.
View 1 Replies
View Related
