i have a E2000 rounter . It's brand new. But i can't setup to use wifi. the software cisco connect can't find rounter. When i plug blue cab from e2000 to my ethernet port on my laptop , icon's network appearen " limit ".
View 3 RepliesI just bought a Linksys E2000 router and ever since I set it up the internet will cut in and out on my desktop and my laptop, but when I unplug the internet from the router and plug it directly into my desktop (that's how I have it right now) it works perfectly. I have already tried to reconfigure the router and that didn't work either.
View 4 Replies View RelatedJust a day or two ago I was able to do what the title says, didn't make any adjustments to my E2000 while in it, had to find something though.Anyhow, connecting to http://192.168.1.1 results in "Unable to Connect", etc. Also tried it in IE9, Firefox Beta is my primary, and it still didn't work. Tried using Cisco Connect and it says it cannot connect to my router. I am wired to my E2000, which in turn is wired to my DSL modem (Actiontec GT701D-Its firewall not in use). I sitll have full connection to the internet as well as other wireless deveices do in my house.
View 1 Replies View RelatedWhen adding a device that has a web protected setup button, can I use the web protected setup button on my Linksys E2000 router to set up the device even though I setup up my router using the Manual setup on the Web Interface configuration?
View 1 Replies View RelatedI recently purchased a Mac and wanted to reset my wireless router and set it up using my mac. However, when I downoaded the software to set it up again, it said it was not compatable with my Mac OS (X Lion 10.7.4). I am sure there is a way to manually set it up via an ethernet connection, but I am at a loss as to how to do that. The wireless router is working just fine, I am able to connect to the internet wirelessly and there's nothing wrong with my internet service, however the wireless router is not secured.I have my Mac connected to the wireles router via an ethernet cord.
View 1 Replies View RelatedSo my family has an E2000 setup near the modem in a room that litterally is a DEADZONE, signal bearly gets in or out of this room. I've argued until I was blue in the face that we ned to rewire the internets inlet to the house in to another room that isn't a deadzone and rune a router from there.They IT disadvantaged refused. We have also an E2500 they say hook it up, maybe it will work better (when your in a concrete and mettal room with a router sitting on a shelf surrounded by book and with a corless phone system hooks up and sitting on top of it... its jsut not going to work. is there a way i can take the E2500 and make it an access point for the E2000?
I figure if I can I would take the E2500 and put int in a better location and jsut have it relay the E2000 internet. Because of the IT limited thought process of most of the people living here I'd prefer that they share the same SSID or atleast make for a simple transition for the apes I live with.
Running Win7. When trying to connect Lenovo laptop to E2000 with Easy Setup Key, the progress bar hangs at 25%. However, the E2000 will connect to the laptop with an Ethernet cable. Same problem on both of my Lenovo G555 laptops.
View 4 Replies View RelatedI have just setup a E2000 at home. All the wireless connections work and also my NAS server who i wired. But when i try to setup my wired media server it will not connect.
View 6 Replies View RelatedI recently switched from dsl to cable. I have a e2000 router that I would still like to use. The modem I have is a Motorola Surfboard SB6121. It has no options that I can modify. The modem has a built in DHCP server. However, I can't modify it and I don't like the ip configuration it uses. For the time being I have the modem connected to a switch which is working fine. What I would like to know is how to configure the e2000 to use the modems connection. I used PPPoE for DSL and had login information.
View 2 Replies View RelatedAfter getting informed that I cannot use the AP I bought yesterday as a bridge, I decided to get another linksys E2000, as the guy in the shop informed me that I can run it in bridge mode for sure.Now, as I am doing this for the first time, and my english is not the best, I was not able to find some instructions, or even better a step-by-step manual that can assist me. I searched the forum, but I did not find anything about the E2000 in bridge mode.
View 7 Replies View RelatedMy WiFi is working, but only to about 20 feet then it slows down to almost nothing...
View 1 Replies View RelatedI have an odd problem where every fortnight to three weeks none of my wifi devices (ipap, laptop, 2x android phones) can connect to my network (Linksys E2000, running firmware 1.0.04 with WPA2 personal). They can all see the network and try and connect, but all fail. Rebooting the router has no effect, and the only thing I've found that works is that I have to connect via ethernet cable (which works no problems) and then disable wireless security, save changes, and then immediately reenable wireless security and save changes again. All my devices then will automatically reconnect no problems. It's a bit annoying as my router isn't ideally placed to dig out the cable, but I wondered if there's any way of diagnosing what could be wrong? I've checked the router logs and they're not useful - the only thing I can see of note is in the DHCP log in the period when I suspect the problem arose I get 4 entries of discover / offer / request / ack going to 255.255.255.255 which seems unusual. But the security log is empty so I get nothing from that.
View 8 Replies View RelatedMy 'main' Wifi SSID will just disappear and you can't connect to it. the guest account will still show up. computers/devices that are already connected will stay connected and will work fine, but anybody reconnecting will not be able to. Only solution I've found so far is to unplug and replug in my router
View 1 Replies View RelatedI have a Linksys E2000 router. I am trying to install an Epson NX230 printer on my home network. Apparently, the Epson printer has a MAC address assigned to it. My network cannot find the printer. I looked at my riuter setup and the MAC Address Clone has two buttons, Enabled Disabled. The Disabled button is clicked on. Accdording to documentation I foudn on this website, it looks like I can Enabled the MAC Address clone button. The document also mentgioend entereding the MAC address for a PC.
If I enable the MAC Address Clone, do I enter the MAC address for the printer or during the install process does the MAC address get installed also
I have a Linksys E2000 router on my home network. The router has the newest version of firmware. Every once in a while, wireless clients on my network become "isolated". Here's an example of what happens. I set up a new wireless printer. I can print to the printer wirelessly from my phone, PC's, etc. all fine after setup. I'm thinking everything is cool!! Well after 2 weeks to 1 month this device will become "isolated" so I cannot print to it; it has an IP address, it can ping its gateway, but i cannot ping it from other devices on the same subnet. I know it's not the printer because if i unplug my E2000 and plug it back in, it works fine.
Another example. I have two windows 7 PC's that are on the same home group and i can share files between them. Sometimes it works and other times it doesnt. I can ping my gateway but they cannot ping each other. I would troubleshoot the issue like crazy from the host end, but the second i unplug my E2000 and plug it back in, BINGO they can talk. Something is wrong with how these routers function with hosts in inter-subnet communications.
I bought a Sonos multiroom-system, and connected the first player to my E2000 router through Ethernet. It then gets a dynamic address through DHCP, I can see the Sonos within the network when looking in the admin tool of the router.When I start the Sonos controller software on my PC (XP), the software can not find the Sonos when my PC is connected through Wifi.As soon as I connect PC to the router with ethernet cable the Sonos is found immediately and can be initialised. After that, I can disconnect the cable and control the Sonos wirelessly. (as long as I don't close down the controller software for too long)
From what I understood from the sonos.com website, the Sonos sends an UPnP multicast signal on port for SSDP on port 1900 for initial connection. Further communications port are described below.Somehow, this multicast package seems not to be transferred into the wireless LAN, only into the wired LAN. Do I have to open some ports, filter some ports?Forward them?
When the Wrt600N came out, it was said that the "Reserved" button would be enabled by a future firmware upgrade to support WiFi Protected Setup. Surely in the three or so years this has come to pass.Does anyone have a link to information on using WPS with the WRT600n?
View 5 Replies View RelatedI bought wrt54g2 several years ago and everything worked fine until this week. I got trouble with this router now.All the computers at my home couldn't access to this router even just connect to router's setup page at 192.168.1.1. The only way go to setup page through LAN Cable .I'm afraid maybe there's interference channel with my neighbor, then I did some change to router channel already, but the result same. I still couldn't access to the router through WIFI
Fyi, I did upgrade the firmware with the latest one and all the computers distance to the router not more then 5 m and in the clear area
Is WRTU54G-TM affected by Wi-Fi Protected Setup security vulnerability? Device is not mentioned on this list: url..If yes, can it be fixed or is device bricked?
View 1 Replies View RelatedI have bought a new WRT54G2 router since the old one broke down. When I log into the 192.168...and click wireless, it takes me to this window that says Searching for your Client Device....If you haven't clicked wi-fi protected setup button please do so now. It's stuck at 98% and I click on the bottom middle button with the 2 arrows constantly and nothing is happening.
View 5 Replies View Related[URL]I have a Linksys E4200, even if i put wireless on manual WPS is still working, any answer from Linksys?
View 5 Replies View Relatedi have a Linksys modem BEFSR81 v.3 and am trying to reset my wifi password for secure connection. When i log into the the admin page, to my surprise, I could not find the security feature to create WPA or WEP password. i'm stumped. This has never occurred to me before on this modem.
View 6 Replies View RelatedI am using 3G to access the internet on my PC. I have a 3G modem connected, and want to setup my Linksys WRT54GL router to enable wi-fi, so other devices can access the internet as well.
View 7 Replies View RelatedThe router was working fine when it was setup but was disconnected for a short while. There is now no recognition of the router and the install cd was misplaced...
View 2 Replies View RelatedI can connect to my router but either way it seems like i can't get any internet access (both wireless and by cable): url...I have tried the steps that the linksys FAQ suggests shall fix this problem, but this has not worked. I have also tried to reset the router without any luck. I know it its not the modem that is causing the problem because I'm wired to it now.On the E2000 every light is blinking as it should be (hence the FAQ) so it indicates that there might be a problem with the connection between the router and the computer (tested on other computers too without success).
View 9 Replies View RelatedI would like to set the router's dns entries but I don't see how to do that. Basic setup page has DNS setep for the DHCP scope but I don't want to push dns to my pc's. What I am looking to do is to use an alternate dns to what my service provder pushes and still have the abliity to route on my internal network.
View 1 Replies View RelatedWe bought our Linksys E2000 in the summer and went to set it up but something came up... Now we are trying to set it up but cannot find our WPA key... Where can we find this?
View 2 Replies View RelatedSo i can only forward 10 ports on my E2000.Example, one game (Battlefield 3) requires 10 ports (TCP and UDP combined).What about my other games? how can one, if possible, add more ports to the router?
View 4 Replies View RelatedE2000. I run the setup program, my laptop sees the router and it shows a strong signal. When I try to connect with it, it won't connect.
View 9 Replies View RelatedI've been looking around like a madman now in the settings. where can I turn off my WPS ? Just cracked my own PIN within 6 hours with Reaver.
View 9 Replies View RelatedMy internet cut out last week and after calling my ISP I found out it was in fact my router that was causing the problem (regular connection to PPOE works fine). I've only had my E2000 about 2-3 months and have not had any problems with it. I've restarted the router, done a factory reset, upgraded the firmware, renewed the IP and still I cannot get any connectivity. I can access the router UI fine and I get a response from pinging it and also I have tried replacing the cables but that didn't fix the problem either.
View 9 Replies View RelatedI have an E2000 that I was given as a gift. I would like to use at it my office for a switch at my cubicle where I can connect 2-3 computers simultaneously. I am in a large network and am a user only. When I hooked the E2000 up today my computers would not get internet access BUT my laptop got wireless access and internet.
View 2 Replies View RelatedI'm using E2000 currently and meet a wireless connection problem. The speed can up to 300M bps. When I confiured the E2000 to band auto (20-40mhz) and my wireless network card to work at also auto (20-40) mode, it always down to 144M speed when connection.
If I changed some settings in E2000's wireless configuration, in the status sheet I can see it works at 40MHZ. But after a while,(5-10 mins) it automaticly down to 20MHZ and my labtop connect only got a 144M speed.
how can I deal with that to make it always keep at 300M connection? Note the previous router I used to connect to my lattop can always keep that speed.