Linksys Wireless Router :: E2000 Won't Allow Deluge BitTorrent Incoming Connection
Feb 7, 2013
I recently downloaded Deluge and while I can download torrents without a problem, I always have the "NO INCOMING CONNECTIONS' warning. I've tried single port forwarding, port range forwarding, turning UPnP off and on ... in short I've tried a lot of stuff and the only thing that clears the message is to remove the router out of the equation. The message disappears as soon as I connect the pc directly to the modem.
View 3 Replies
ADVERTISEMENT
Aug 26, 2012
My firewall outpost detected incoming connections on port 80 and blocked them.I think that the router must block incoming connections on port 80, right? But it does not.
[URL]
View 5 Replies
View Related
Nov 7, 2011
I have a Cisco E3000.My roommate is using our internet connection (in fact mine) to donwload on BitTorrent networks. I could block BitTorrents urls, but she could dowload the torrent file from another connection and do the download with my connection. So I forgot that way.I could also block ports... but she could change the ports of the BitTorrent network...
View 7 Replies
View Related
Mar 2, 2011
Admins could you move this over to Linksys Support, just noticed it's in the wrong place
View 5 Replies
View Related
Aug 30, 2011
I am using a E2000 connected to a DSL modem via the internet port. My modem is able to connect at gigabit speed but it doesn't seem to be the case with the E2000. All other ports are running at gigabit speed without problem. Is there any parameter that can be modified or is it a router limit?
View 2 Replies
View Related
Sep 18, 2012
I recently purchased a Mac and wanted to reset my wireless router and set it up using my mac. However, when I downoaded the software to set it up again, it said it was not compatable with my Mac OS (X Lion 10.7.4). I am sure there is a way to manually set it up via an ethernet connection, but I am at a loss as to how to do that. The wireless router is working just fine, I am able to connect to the internet wirelessly and there's nothing wrong with my internet service, however the wireless router is not secured.I have my Mac connected to the wireles router via an ethernet cord.
View 1 Replies
View Related
Aug 12, 2011
i want to set up a vpn connection to my home network. i see that the e2000 supports ipsec, but does not provide a client. what client can i use to establish a connection?
View 4 Replies
View Related
May 5, 2012
I switch on router and connect my iPad on router linksys cisco e2000. During 10 minutes, There is no problem. After 10 minutes, I have always the connection with my router but no internet. To Avoid this problem, i restart the router with switch and after, no problem. Do you have any ideas to avoid this lost connection after 10 minutes when I switch on my router.
View 2 Replies
View Related
Sep 10, 2011
I have 300 Mb/s plan from ISP. Then cable connected directly to PC my throughput is as it should be, but then i do connect my PC via E2000 cable connection, it slows down to 200Mb/s. I have tryied also E4200 model and i have same issue.
View 1 Replies
View Related
Sep 13, 2011
Internet was working great a few days ago with my e2000 and comcast as my ISP. I've got a few devices connected through ethernet connections on the unit. We also connect to the e2000 wirelessly.Problems started yesterday with no internet. Last night I rebooted everything and still nothing works. Connected laptop to cable modem directly. Wasn't getting internet connectivity so I called Comcast. They reset my modem and everything started working fine. Now I can directly connect from cable modem to laptop and internet works fine. I try connecting the modem to the router and still no internet.
View 2 Replies
View Related
Jun 14, 2012
My connection to Davis Instruments' WeatherLink had been working for many weeks, when my old WRT54G quite renewing DHCP leases. I've replaced it with a new E2000. All seems well. The Wifi network is working and my server resources to the outside are working. But the blasted WeatherLink software complains that it can't connect to to the interface box. This is a wired connection. The software finds the MAC address of the interface box and the assigned IP address, but "testing" the connection fails. I can ping the IP address of the interface box. The Davis people insist this is an issue with the router. The WeatherLink software uses a weird port: 22222 I didn't know there were ports with 5 digits. I've tried port forwarding this to the IP of the computer, but nothing changes. I think if I can ping the IP of the interface from the computer, communication should work.
View 1 Replies
View Related
Jun 28, 2010
I use to use 2 routers, one for me and my dad, another for my brother and sister. We decided to get rid of the other router, and make our cisco E2000 our main router, but, everything on the router settings got removed so we had to reset it up. I remember reading an advanced setting guide on making my wireless speed go from 13.5MBPS to 216 MBPS, but i forgot what the settings was in advance settings.
View 7 Replies
View Related
Jun 21, 2010
I bought a brand spanking new Linksys E2000. I get great connection speeds and awesome range, until the day I set up parental controls. Once I set them up, It slowed my connections down to a crawl. Thinking that I did something wrong, I reset the router and did the entire installation. Everything was back to normal, but it did it again once I set up the parental controls.
View 9 Replies
View Related
Apr 26, 2013
Region : Hongkong
Model : TL-WDR4900
Hardware Version : V1
Firmware Version : 3.14.3 Build 130320 Rel.39025n
ISP : PCCW Netvigator
I have upgraded to the latest firmware which solved lots of problems regarding unstable wifi connection as well as BitTorrent / P2P transfers.But I also observed that when my BT is on (Transmission for Mac) at around 50KB/s upload and download, my network latency hikes up from some 30ms to 500ms which affects a lot on web browsing or other apps requiring Internet.My BitTorrent app is showing I am merely making some 20 peers connection so I am not convinced that is an ISP problem but it's more about the router.
View 1 Replies
View Related
Dec 9, 2011
I have the AE1000 adaptor on my wife's computer and direct wired on mine is the E2000.The e2000 is set to 2.4mhz and when connected to the wireless network, my wifes ae1000 shows it is connected at 144mbps.When I change the e2000 to 5.0 mhz and then my wife connects to the internet, she shows the ae1000 at 16-53 mbps. When I switch back to 2.4 she shows 144. I thought that when the e2000 is connected at 5.0 she should have a "faster connection".
View 1 Replies
View Related
Jun 3, 2012
I recently bought a new Cisco/Linksys E1200 router, but the incoming log feature does not work. Outbound and Security logs work fine, but unsolicited inbound TCP packets (that are dropped) are not displayed. The inbound log is empty.
View 6 Replies
View Related
Apr 4, 2013
My incoming log is FILLED with incoming IP's and they are all connected to a port starting with 64-. I've tried changing my wireless internet with different passwords multiple times and I have upgraded my firmware.
View 1 Replies
View Related
Aug 8, 2012
my WRT54G has been configured to block any and all incoming connections.continue to have disabled all port forwarding, port triggering, the DMZ, and QoS, via the applicable tabs under the [Applications & Gaming] Panel. The WRT54G continues to be configured to operate as a Gateway.No static routes are defined. The routing table show four entries, none of which are remarkable or match in anyway the partial address identified above.So I am under the impression that my WRT54G should be ignoring everything from the WAN-side.Even pinging the WAN-side of my router from the outside internet times out.My WRT54G ver 6 is at firmware level 1.02.8, which, as far as I can tell is the latest issued by Cisco.I am completely perplexed how such a connection is being established, and do not know if it is or has the potential of causing any harm. My own research indicates port 520 is typically used for RIP protocol, but I have almost zero knowledge of such.
View 9 Replies
View Related
Oct 13, 2011
I am trying to use my WRT120n as access device for an IP Centrex service using SIP protocol. My SIP phone is located right behind the router.My problem is sometimes the router is dropping incoming calls because signalling packets are fragmented at IP level. So I cannot receive those calls.Is there a way to enable the router to accept these packets?
View 9 Replies
View Related
Feb 12, 2012
I have a WRT160N router (firmware 1.53.0) that is connected to my broadband. It is giving me problems with VOIP/SIP Traffic.My SIP client connects fine and makes calls, but I cant hear any incoming/outgoing sound. The SIP client works fine when connected directly to broadband. I tried DMZ and that didn't work. Disabled SPI and that didn't work too.
View 2 Replies
View Related
Dec 23, 2011
I've been fighting with my E2500 since I got it back in June with lag, dropped connections, etc. It's a bit intermittent but can hang around for hours at a time when it kicks in. Restarts but the issue always comes back. Most noticeable while gaming online or on a VOIP program such as Team Speak. Generally when it happens If I'm monitoring my Team Speak connection the incoming packet loss shoots up between 20-30%, starting to drop out every other word or so. No out going packet loss. The connection drops are random between computers (I have one mac and one pc in the house) where one will be fine and the other wont, or when the whole system will stay connected and drop all transfer. In the case of this last one it's not my ISP's connection as any streaming happening between one computer and an Apple TV device will also cease. I've also swapped back to my old router (an older model linksys) and all problems have stopped. Fully rebooted and reconfigured the router about 3 or 4 times and am on the latest version of firmware (1.0.003). It was much worse on 1.0.002 but still very noticeable on 003. Also no difference with a different wireless adapter. I've tried the chat technical support but all they did was take 45 minutes to tell me how to reboot my router after telling them I already had.
View 1 Replies
View Related
Jun 20, 2012
Have a few of these routers internally as well as at various clients. The incoming and outgoing logs show up blank, even when there are 10-20 computers using the Internet and I know there is traffic being generated. DHCP and security logging still works fine. I also have a few E1200s on the latest firmware that are logging just fine... I'm just having issues with the E2500s.
View 6 Replies
View Related
Aug 21, 2011
I can connect to my router but either way it seems like i can't get any internet access (both wireless and by cable): url...I have tried the steps that the linksys FAQ suggests shall fix this problem, but this has not worked. I have also tried to reset the router without any luck. I know it its not the modem that is causing the problem because I'm wired to it now.On the E2000 every light is blinking as it should be (hence the FAQ) so it indicates that there might be a problem with the connection between the router and the computer (tested on other computers too without success).
View 9 Replies
View Related
Jan 27, 2012
I would like to set the router's dns entries but I don't see how to do that. Basic setup page has DNS setep for the DHCP scope but I don't want to push dns to my pc's. What I am looking to do is to use an alternate dns to what my service provder pushes and still have the abliity to route on my internal network.
View 1 Replies
View Related
Oct 2, 2011
We bought our Linksys E2000 in the summer and went to set it up but something came up... Now we are trying to set it up but cannot find our WPA key... Where can we find this?
View 2 Replies
View Related
Jan 28, 2012
So i can only forward 10 ports on my E2000.Example, one game (Battlefield 3) requires 10 ports (TCP and UDP combined).What about my other games? how can one, if possible, add more ports to the router?
View 4 Replies
View Related
Nov 3, 2011
E2000. I run the setup program, my laptop sees the router and it shows a strong signal. When I try to connect with it, it won't connect.
View 9 Replies
View Related
May 28, 2012
I've been looking around like a madman now in the settings. where can I turn off my WPS ? Just cracked my own PIN within 6 hours with Reaver.
View 9 Replies
View Related
Apr 24, 2011
My internet cut out last week and after calling my ISP I found out it was in fact my router that was causing the problem (regular connection to PPOE works fine). I've only had my E2000 about 2-3 months and have not had any problems with it. I've restarted the router, done a factory reset, upgraded the firmware, renewed the IP and still I cannot get any connectivity. I can access the router UI fine and I get a response from pinging it and also I have tried replacing the cables but that didn't fix the problem either.
View 9 Replies
View Related
Aug 28, 2011
I have an E2000 that I was given as a gift. I would like to use at it my office for a switch at my cubicle where I can connect 2-3 computers simultaneously. I am in a large network and am a user only. When I hooked the E2000 up today my computers would not get internet access BUT my laptop got wireless access and internet.
View 2 Replies
View Related
Dec 7, 2011
I'm using E2000 currently and meet a wireless connection problem. The speed can up to 300M bps. When I confiured the E2000 to band auto (20-40mhz) and my wireless network card to work at also auto (20-40) mode, it always down to 144M speed when connection.
If I changed some settings in E2000's wireless configuration, in the status sheet I can see it works at 40MHZ. But after a while,(5-10 mins) it automaticly down to 20MHZ and my labtop connect only got a 144M speed.
how can I deal with that to make it always keep at 300M connection? Note the previous router I used to connect to my lattop can always keep that speed.
View 2 Replies
View Related
Nov 14, 2011
I have a E2000 router that would go out and I would have to unplug and replug in every once in a while. Finally it just stopped working completely. I reset the router and now it won't let me connect. I have followed advice given to soembody else on here and went into router settings and cloned the mac, the IP address was there and reset my security settings. It let me connect to the network but not the internet...
View 2 Replies
View Related
Apr 21, 2013
I have a Linksys E2000.
It worked fine until one day, without any change at all, it simply stoped working. I mean, I can still connect through my wifi laptop connection (it shows connected to my router and says that I have an excelent signal). But, I can't reach the internet. But, If I unplug the internet cable, and plug it in my laptop, the connection works fine. A friend told me that this could be caused intentionally by the internet provider, that they would block my signal to avoid me using a wireless router, trying to force consumers to sign their own wireless service. Thus, by this friend advice, I've cloned my laptop's MAC address to the router. It didn't work either.
View 4 Replies
View Related
