My firewall outpost detected incoming connections on port 80 and blocked them.I think that the router must block incoming connections on port 80, right? But it does not.
[URL]
my WRT54G has been configured to block any and all incoming connections.continue to have disabled all port forwarding, port triggering, the DMZ, and QoS, via the applicable tabs under the [Applications & Gaming] Panel. The WRT54G continues to be configured to operate as a Gateway.No static routes are defined. The routing table show four entries, none of which are remarkable or match in anyway the partial address identified above.So I am under the impression that my WRT54G should be ignoring everything from the WAN-side.Even pinging the WAN-side of my router from the outside internet times out.My WRT54G ver 6 is at firmware level 1.02.8, which, as far as I can tell is the latest issued by Cisco.I am completely perplexed how such a connection is being established, and do not know if it is or has the potential of causing any harm. My own research indicates port 520 is typically used for RIP protocol, but I have almost zero knowledge of such.
View 9 Replies View RelatedI have a E1500 hooked to a Galaxy Broadband/Hughes Satellite internet system. From the router I have gone to a EZXS55W ver. 4 switch. Off of the switch I have 2 computers and a PoS machine. The satellite system gives us a dynamic IP. I am noticing that my connection from computer to computer and also from them and the POS machine to the internet is constantly switching on and off, it seems. Any ideas what could be causing this issue?? We just recently went from a Static IP to the Dynamic IP. We did not have this issue with the Static IP and wondering if there are some settings I have neglected.
View 1 Replies View RelatedI am not getting anywhere near the same download speeds to my wireless laptop as my wired desktop? When I run the Xfinity speed test on my wired desktop I get anywhere from 18MB to 40MB downloads.But the same Xfinity speed test to my Wireless connection to my Dell laptop [G adapter] never gets above 15MB.Is there a checklist anywhere I can use to maximize my wireless speed to a [G adapter] wireless device?
View 9 Replies View Relatedmy router stop getting internet connection its plugged in but keeps telling me no reset modem or unplug router
View 4 Replies View RelatedI bought this new router, and at first it seemed like it was working okay, but then i started noticing that my roku box (watch netflix) was cutting out all the time, losing the connection from the new router. I also began to notice that if more than one person was online, pages took forever to load, can't watch youtube videos and even listening to music online like Pandora became difficult. Also it says that I can get up to 300 mbps but when i run the test I get .50 download and about 1.8 upload Details About Router & Connection,Its a Linksys E1500 with the capability of up to 6 devices and my IPS is Comcast.
View 1 Replies View RelatedI'm using a Linksys E1500 on my Timewarner 20Mbs connection and I've noticed that anytime another computer on my network connects my connection speed take a significant drop. This happens when Macs or PCs connect and there doesn't seem to be any common ground between any of them. In addition the connection is slow wether the other PCs are idle or downloading anything, it seems to make no difference. my ping in any game drops from 70 to 500 just for 2 other PC being on at the saem time on the network.
View 2 Replies View RelatedI set up the e1500 and everything worked well, my download speed over the wifi was something like 50mps, now its down to .3 mps over the wifi. When I'm hardwired to the router the speed goes back up and everything is fine. The only problem is the wifi. Its not the ISP because my roommates aren't having a problem with their wifi at all. I haven't changed anything on my computer except updated some drivers since I set up the router. My network card drivers are up to date and so is the router's drivers. I'm also doing all this about 5 feet away from the router.
I have a Dell XPS L502x running win 7 64 bit.
Updated firmware was installed and settings were reviewed. Intermittently the E1500 looses its ability to connect only to our Android devices and "Cisco Connect" displays that it has lost Internet connectivity. The PC hard-wired to the E1500 and another PC connected wirelessly both work fine when this happens, despite the Cisco Connect message. The Android devices show the presence of the network, but they never "connect" - find the IP address. The problem can only be resolved by re-booting (powering off/on) the E1500. The loss of connectivity to our two Android devices and the Cisco Connect error display always are concurrent. E1500 looses connection to Android devices
View 9 Replies View RelatedI recently downloaded Deluge and while I can download torrents without a problem, I always have the "NO INCOMING CONNECTIONS' warning. I've tried single port forwarding, port range forwarding, turning UPnP off and on ... in short I've tried a lot of stuff and the only thing that clears the message is to remove the router out of the equation. The message disappears as soon as I connect the pc directly to the modem.
View 3 Replies View RelatedI upgraded my old Linksys wrt54g to the E1500. All the XP os are connected via cable and wireless connection, but the Vista laptop i get local access only connection error. This laptop used to connect on the older router using wep but with E1500 wpa-2 it cannot connect. I am unable to ping the router from the laptop wireless. Connecting ethernet cable it works fine and logging in as a guest works does too.
View 1 Replies View RelatedWhen i open Skype it try to allow incoming connection to port 57502.
Both times Little Snitch caught it. Attached are two images.
What would this connection be, I read this port is dynamic/private?
Im using a Linksys E4500 wireless router behind a Motorola SB6121 modem. My OS is Windows 7 and it is fully up to date. In general my entire network is working well. Now I have purchased a new IP surveillance camera and need to forward a port to be able to have remote viewing of the camera. Mi ISP blocks quite a few inbound ports including 80 so I have been trying a lot of ports all over the map to find something that will allow inbound access.
After several hours, nothing I have tried works, using a couple of different port probes including one called CanYouSeeMe I always get a "timed out" message. I have disabled the firewall in the router and on the local computer and still no luck. This says to me that either Cox is blocking nearly all ports (doubtful) or the modem is blocking access to the router somehow.
The Surfboard modem doesn't have a built in router. Unfortunately I don't have an old working modem to put in the circuit.
I don't guess it matters but the camera is accessible from all other local computers on the LAN using its IP address with a port number appended (right now it's using 8000).
making a wireless connection from my broadband router model td 8816?
View 1 Replies View RelatedI have tried everything and every connection suggested and still can not get a wireless conection.
View 2 Replies View RelatedHave to re-boot 1-2x daily. Updated firmware through Cisco, followed by about 7-8 support calls. They all recommend some sales thing, new router, computer update and clean-up, or blame it on my modem (not the case). When E1500 goes down, all wired and wireless connections are lost. They all recommend some sales thing, new router, computer update and clean-up, or blame it on my modem (not the case).
View 4 Replies View RelatedIf the wifi can be turned off on the E1500. I got this unit from a family member and do not need the wifi part, as I have two computers, but are in the same room. I have the cisco connect on my computer and do not see a disable wifi in the program anywhere.
View 1 Replies View RelatedI just purchased a e1500 to replace my wrvs4400n which sadly died. yea I do loose a lot of features. I set up everything without a hitch but when I try to use Wireless-N mode only, none of my computers can connect to the router and all my computers use N cards. I'm stuck on using Mixed Mode which limits my speed to G speeds. I didn't purchase this to be a G router but an N router and it seems N mode has issues. I am on the current firmware.
View 9 Replies View RelatedI recently purchased the Linksys E1500 and at first, had no problems with it. The last few days I've had issues however. I tried logging into the internet and my WIRED computer would not connect. My wifes WIRED computer next to mine didn't have any trouble connecting. Resetting my computer didn't work. I had to cycle the router by unplugging it! Then today, my (2) kids are using Pandora on their (2) computers wirelessly, and same set up with my wifes computer and mine, and again only my computer looses access from the router and all other computers stay connected.
View 9 Replies View RelatedI followed the directions at least 6 times and I still had no internet connection. Is this because I have Windows 8 and all directions are for windows 7? I finally gave up and hooked back up our 6 year old belkin wi fi router. Had internet access in 1 minute. I bought this wi fi router was because Amazon described it as simple, quick, automatically does the work of hooking it up for you. Takes less than 5 minutes.
View 2 Replies View RelatedI want access to my e1500 with using a password
View 1 Replies View RelatedSo I just got this router in hopes that I would get a better signal within my room as opposed to my older router. Unfortunately, nothing has changed, in fact I think I'm getting weaker signals. My previous router was a D-Link WBR-2310. I went to speed test.net and tested 3 variables. My wifi on my desktop in my room, my wifi when right next to a router on my laptop, and my wifi using my neighbors wifi in my room.
My room Desktop Wifi:
Download was 0.50 mbs Upload: 3.6
My laptop right next to Router:
Download 19.87 mbs Upload: 3.5
My room Desktop Neighbors Wifi:
Download was 17.3 mbs Upload was 3.32.
What is the point of this new wireless N router, when it can't beat a G router older model in reach? And why does is have a 0.50 mb d/l speed but a 3.6 upload speed?
I have my internet coming into my WAG120N and going out wirelessly. I want to setup a wireless bridge between this and an E1500, so I can connect my TV to the E1500 (via an ethernet cable) and have it access the internet. Unfortunatly I can run a cable from the WAG120N to where the TV is. So it I can get the E1500 wirelessly bridged to the WAG120N? I have updated the firmware ont he E1500 to get Bridging support, but from what I can tell it only provides bridging via an ethernet cable. Is there away to bridge wirelessly?
View 1 Replies View RelatedI just purchased an E1500 router to create a wireless connection. I had been using an older Cisco model previously.
I can't get it to connect. I have tried everything that is written in the support articles. In particular, I followed the article 3686, about setting up a router with cable internet modem, after the Cisco Connect didn't create the connection automatically.When I plug the laptop directly into my modem, I have a connection. I have reset the modem and the router several times in the process. I've been to the web-based setup page and followed all of the instructions about cloning the MAC. When I hit the release and renew IP addresses (under the Status tab), nothing happened. They remained 0.0.0.0
Called my ISP, but they say it's a router issue.I think I'm going to start from scratch--uninstalling the Cisco Connect, reinstalling it, turning everything off and back on again to see if it somehow will work automatically.
I just purchased a new linksys e1500 and followed the steps on the cd to set it up. I have internet access on my windows 7 laptop and iphone however, I have "local access only" on the two laptops we have running vista. The router is working fine for the windows 7 machine and the iphone but I cannot connect to the internet on the two vista machines.
View 9 Replies View RelatedI ordered a linksys E1500 for a home office. There are 3 computers that connect wirelessly: a 8-year-old desktop with a Netgear USB adapter, a 1.5 year old laptop and a 3.5 year old netbook, both with internal wireless cards. The desktop and netbook are running Windows XP and the laptop runs WIndows 7.
The desktop (XP) and laptop (Windows 7) are able to connect with no problem. However, the netbook (XP) is having problems connecting. It is able to connect to the router using the WPA2 key, and says it has excellent signal. However, when I start up an internet browser, it gives me a DNS error for any page I try to access. Connecting directly to the router with a cable works fine.
I got on the phone with Linksys support. They told me the problem was that the computer wouldn't use WPA2, but when I switched to WEP, it didn't work at all! I switched back to WPA2 and have the same problem as before: it connects to the network but DNS error messages for any website I try to access (And I've tried both Chrome and Explorer).
To make things more interesting, I set up a guest network on the router, and the netbook connects fine through that so far!
Which one have the best range ? I know that the E1500 has SpeedBoost feature but does it matter ? I can get both for the same price.
View 1 Replies View RelatedI have an E1500 N300 Router, I've had it for 3 or 4 weeks now. Ever since I've had it, I can no longer send e-mails out with Eudora nor Outlook. I've tried using about 3 different SMTP's just to verify that it wasn't a server issue. I tried Port Forwarding in the router settings. I selected SMTP and POP3 and checked Enable on both, then save changes. But they don't appear to be taking, as when I go back in and try to set them again, it let's me and doesn't give me a Port Overlap warning. I've been told that I shouldn't need to mess with Port Forwarding at all, I just need to go into the Firewall settings and open up the SMTP, POP3, and IMAP ports. However, I don't see any settings in my Router settings to allow this, aside from Port Forwarding and it's not actually saving the changes. I will admit, I'm not all that great with this stuff, and this is the first time I've had any issues with a Router stopping me from E-mailing.
View 9 Replies View RelatedJust bought an E1500 wireless router -- when setting the router name and password, a 2nd guest sight came up, but I had to leave the computer, and when I came back that page was not there. I do have a guess password, that is fine---what I want to remove is the guest signal to our Dish Network wireless sight.
View 2 Replies View Relatedi got my ps3 & xbox to connect it was easy but when i go to connect my iphone it doesnt even let me put my password in it just says"cant connect"?
View 3 Replies View RelatedI'am using router E1500 in a bridge mode (aka WiFi access point N standart). I want have two chanel transmitions, but i see only one chanel. In a specification write 2T3R (up to 300 Mbps).
View 6 Replies View RelatedI recently connected E1500 to time wanrner cable modem for my home. 3 laptops work fine, but iphone and ipad can not connect to wireless. But iphone and ipad connected to linksys guest automatically.
View 4 Replies View RelatedI have Vista Home on a laptop (all up to date) and when I try to set up wireless connection using a key it goes to 25% then times out. When I try to manually set up a connection I get limited connectivity and no internet. I have one other laptop with Win 7 and this connected with no problems, also one desk top connected with no problems. Kept getting the error 82BD0119 on the Vista laptop.
View 5 Replies View Related