In our house we use a Linksys WRT54GL router. When I am connected to the router via a cable I can play an online RPG without any problems.I recently connected an acecss point to the router ( a belkin N1 ). Even if I am connected with a cable to the accesspoint, which is connected to the router by cable as well, I get huge lag spikes about every 10 seconds while playing the game.
View 10 RepliesI just recently picked up a DIR-655 to replace my WRT54GL, hoping that I could get a better stream in my house. The house is 100 years old with plaster and lathe, and I can't relocate the modem and router. So I figured I could use my old WRT54GL as a signal booster/access point on the second level of the house. I read through a couple of guides, and I could get the router to broadcast the signal with full bars, and I could attach to it, but I didn't get any internet. The D-Link is a DIR-655 with firmware 2.10NA. The Linksys is a WRT54GL with Tomato 1.25. Here are a couple screenshots for the DIR-655
View 1 Replies View RelatedI got an Fritz Box from my new Provider to connect to the internet using Fiber To Home. the box is now im my living room and also acts as an WLAN Router. I would like to configure my WRT54GL which in located in my office from a router to a repeater to establish a WLAN bridgde.
View 3 Replies View RelatedI have WRT54GL and want to setup wap54g as wireless repeater? I need to expand the signal using wap54g
View 1 Replies View RelatedAny issues connecting an N access point via an ethernet cable to a G router?I currently have a wrt54gl router in one room (where it's connected by cables to various devices). I'm usually in another room and connect via wifi with other devices. Internet speeds over wifi are fine, but speeds are too slow when transferring files from wifi devices to other computers (windows file sharing).
I'm thinking of running a cable through a wall from the wrt54gl room to the other room and connecting a small N router, in access point mode. I'd then connect to the N access point and, through it, to the main router and other devices in the network.All wifi devices can run N.
Are there any issues in doing this? Anything I should know about configuring this? From other questions, it's not clear if I should use the same SSID for both routers. For that matter, should I turn off wifi on the wrt54gl?
Few months back i had upgraded my Lynksys router with Coova AP firmware. Everything was working fine.I had configured the AAA server on CoovaAP and was able to access the internet.I had configured the user name and password as a "testuser" and "password" respectively. With that user id i used to access the Coova AP router and internet. Now i want restore the WRT54GL firmware on Lynksys router. But with the used id and password which i had configured the router is not at all accessible. So i did 30-30-30 reset on the router 2-3 times.
Now i can see openwrt login page with 192.168.1.1 IP address. It is asking for user id and password. I tried all the combinations of user id and password, but no luck. I browsed some link on the internet and some people have recommended that default user id as a "root" and blank password. But with that also the router is not accessible. I cant to do much on the router untill i will log in to router. I have spent lot of time on this.
how to restore back the original WRAT54GL firmware on my router. Anyhow i want WRAT54GL firmware on Lynksys router. Can somebody tell me how to achieve this?? Or atleast what user id and password should i try to log in to router?I tried to use telnet command on the router (Connected router to linux based computer with ethernet cable). But telnet also not working. It is not asking for password, and it saying disconnected.
I had configured the AAA server on CoovaAP and was able to access the internet.I had configured the user name and password as a "testuser" and "password" respectively. With that user id i used to access the Coova AP router and internet.Now i want restore the WRT54GL firmware on Lynksys router. But with the used id and password which i had configured the router is not at all accessible. So i did 30-30-30 reset on the router 2-3 times. Now i can see openwrt login page with 192.168.1.1 IP address. It is asking for user id and password. I tried all the combinations of user id and password, but no luck. I browsed some link on the internet and some people have recommended that default user id as a "root" and blank password. But with that also the router is not accessible. I cant to do much on the router untill i will log in to router. I have spent lot of time on this. How to restore back the original WRAT54GL firmware on my router. Anyhow i want WRAT54GL firmware on Lynksys router
View 4 Replies View RelatedWe have received from a customer of us an WRT54GL box configured with a Coova software. This Wifi router was supposed to be a Wifi hotspot, but was not configured by us. This box is able, on startup, to get an IP by DHCP, to touch a remote Radius server, and so on (we "tcpdump" the Internet traffic, and we saw DNS requests, radius requests, ...)...
But, we are unable to connect to this box,by SSH or by HTTP, either by plug-in PC to the Internet RJ45 or the LAN RJ45. It has no IP as 192.168.1.1. Instead, it was configured to have 192.168.1.1 as gateway.
Of course, we have no doc on previous install, but only the admin/root password for SSH.We are afraid to lose the config (coova, ...) if we perform a hard reset.What is the best way for connecting on this box ?
I had configured the AAA server on CoovaAP and was able to access the internet.I had configured the user name and password as a "testuser" and "password" respectively. With that user id i used to access the Coova AP router and internet.Now i want restore the WRT54GL firmware on Lynksys router. But with the used id and password which i had configured the router is not at all accessible. So i did 30-30-30 reset on the router 2-3 times.
Now i can see openwrt login page with 192.168.1.1 IP address. It is asking for user id and password. I tried all the combinations of user id and password, but no luck. I browsed some link on the internet and some people have recommended that default user id as a "root" and blank password. But with that also the router is not accessible. I cant to do much on the router untill i will log in to router. I have spent lot of time on this. how to restore back the original WRAT54GL firmware on my router. Anyhow i want WRAT54GL firmware on Lynksys router.
I tried setting up a home network with my above Linksys router and can't connect to the internet now. I have the ethernet cable from my DSL Modem hooked into the ethernet port on the back of the Router. In port one, I have a cable which attaches directly to my laptop as I was advised to use a cable for initial setup of my home wireless network. I was able to get into the router to set all the passphrases and wireless security settings, etc. My ISP is PPPoe and I have entered both the UserId and Password that my ISP provided. However, upon clicking on the wireless icon, my system states I am connected but the status screen shows "No internet access". I have no problem connecting to the Internet when the cable runs from my DSL modem into my computer, so it's something to do with the router blocking it now.
My ISP does not support my Linksys router, of course, and they tell me I need to contact the manufacturer telling me the router needs to be set up as a 'bridge" ??? There is no mention of anything like this in the manual and I do not know if there is a setting on the router that is somehow blocking my being able to get an internet connection. This is all still with cables attached. Again, I seem to be able to 'connect' to the wireless network but I now cannot get to the Internet thru the router...
I got an Linksys WRT54GL-DE and my problem is,that someone manipulates the router.Is there any chance to protect the router in that way,that is not possible to reset the router by using the Reset-ButtonNOR by the Linksys software-tool?Especially the software-tool is the problem - I am afraid,that somebody reset / manipulate the router by using the software.
View 3 Replies View Relatedi want to block all internet access on all my computers from the time range of 9 PM to 8 PM. Yes, that gives 1 hour of internet access per day. However, it seems that there are certain rules of the router that won't let me do this. It seems I can't make 2 different policies for PC's within the same IP range (192.168.1.0 to 192.168.1.254) , it gives me the error: "The values you entered are invalid. Please try again."every time I try to do so. And when I try to give the time range from 9 PM to 8 PM it gives an error stating that the end time must be bigger than start time. I am using the WRT54GL with firmware v4.30.7.
View 5 Replies View RelatedI own an AG214 ADSL2 router that I use for my desktop PC. I now however also have a WRT54GL for wireless connection. I connected the WRT54GL to my AG214 via ethernet. Everything works fine, I have wifi and I can use it to connect to the internet. However when I go to my router (192.168.x.x) I can't seem to be able to find a wireless tab to configure my wifi settings. The network right now is unsecure and has a default name (linksys). How do I access my wireless settings? When I access my router it does go to the AG214, do I need to access the WRT54GL? If so, how do I do that?
View 4 Replies View Relatedsetting up my new WRT54GL.this is my first encounter with a wireless router, though I've had 3 previous Linksys (hardwired) routers.I have to say, given that they give virtually no Mac support, it was a breeze….just plugged it in to my cable modem and my laptop and - boom - on the net on my first try!I'm able to access the router via it's web-based system and can now "tweak" with settings, but I'm running in to a lot of "tweakable" settings that I'm not familiar with.
First my setup. I have; (a.) 3 desktop Macs and a Samsung TV hardwired to the four Ethernet ports and (b.) my Mac laptop accessing the router via Airport Extreme wifi. All are happily accessing the web.But I realize that the reason that "(b.)" is accessing the web is that I've changed no default settings in the router and, not only can *I* access the router via wifi, but probably anyone driving down the road or sitting out in front of my house can access the web via my wifi. And I'd like to change that.I'm *guessing* that the router settings i need to change lie in the "Wireless Security" area of the router? And it's here that I'm running in to a lot of "tweakable" settings that I don't understand.But let me give an example of what I would *like* to accomplish.
Let's say that there are 3 different laptops…."A", "B" and "C". All 3 are Macs and running Airport Extreme.Now, "A" is my laptop, sitting here on my desk next to the router. As i leave Airport always turned on, I want "A" to *always* have access to the routers wifi *without* having to enter a username/password, i.e. when i turn "A" on, it's wired.Now "B" might be the laptop of a friend who happens by the house and need access. They would need to find my network on their laptop and then i would need to give them a password to let them get on .And finally, "C" is the guy I don't know out in the street whom I want to *never* have access to my network.So my question then is, can I accomplish this by changing settings in "Wireless Security" on my router and how/what would I change?
I just bought a WRT54GL which is working perfectly. I needed it to extend my home network for my kids (I have not a very fast internet connection and my kids are eating all of it... With the WRT54GL I can choose how much they can have. So my own network has a netgear modem and a netgear wifi access point which is in this network : 192.168.0.x.
This network is not blocked in any way (just password protected). For my kids network, the WRT54GL gives addresses in this network : 192.168.1.x and is limited in speed. Everything is perfect, I have internet connection on both of my network, There is just the problem that I cannot access my printers, my servers, my computers.... that are on the 192.168.0.x network from 192.168.1.x. Is there a solution ? I already tried to force the WRT54GL to go to 192.168.0.x network but no more connection. Should I "bridge" the two networks ? How can I do it ?
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedI just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
I had to reset my access point but the login screen fails to appear to lock the router. I don't have the setup wizard disk.
View 9 Replies View RelatedI have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
View 1 Replies View RelatedHave a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
View 1 Replies View RelatedI have AP WAP 4410 N, and I want conected AP to cacti. Where is I faoun MIBs or OIDs for my Access Point?
View 1 Replies View RelatedI've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine!
The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
View 4 Replies View RelatedI'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
Is it possible to configure WRT120n as an access point?
View 1 Replies View RelatedI have 3 E3000 Routers and would quality input regarding using 1 of the E3000 Routers connected to my Broadband Modem (Roadrunner) and would like to know how to configure the remaining 2 E3000 Routers to be hardwired to my main Router as Access Points located approximate segmented 1/3rd areas throughout my house which really is only 1800 Sq.Ft. in area. How to be configure these routers as access points as well as configuring the main router that will be connected to my broadband router. This is my first network to utilize streaming video, Internet Television Programs, Internet Radio, Accessing the Internet in all rooms of my house and outside the immediate adjacent patio area.
View 1 Replies View RelatedI have tried to find mib for my Linksys WAP54G acces point without succeed. Any body know how I could find it?? I want to program a software based on SNMP protocol. Is there some databses for mibs?
View 1 Replies View RelatedCan i use linksys as an access point?
View 1 Replies View RelatedI have two routers, one is NETGEAR with the MACINTOSH computer and the other is LINKSYS wireless G...what I want to do is make the the LINKSYS router an access point for my network and need to know how to do so.
View 1 Replies View RelatedHow can i use Linksys E2000 rounter as a Access point ?
View 1 Replies View Relatedi have a verizon usb720 modem. i want to set up my wirless printer. Previously i had this set up by a profesional. I bought a new computer and am now trying to set this up. I have a linksys router as well wrt54g how is tis done. you cannot connect anything to the modem but i have read that you can turn the router into an access point.
View 10 Replies View RelatedI have a linksys e1000 modem router as the wireless internet connection in my home, now I bought a new one linksys e1000 to use it as an access point to cover the uncovered area, How can I do that?
View 1 Replies View RelatedHow do I configure my Linksys N Router for a Netgear Wireless N Access Point set in repeater mode? Linksys and Netgear are communicating, but no Internet access is available on Netgear which makes me think I need to configure Linksys to provide Internet connectivity to the Netgear access point repeater.
View 1 Replies View Related