Linksys Wireless Router :: WRT54GL Says No Internet Access
Dec 7, 2012
I tried setting up a home network with my above Linksys router and can't connect to the internet now. I have the ethernet cable from my DSL Modem hooked into the ethernet port on the back of the Router. In port one, I have a cable which attaches directly to my laptop as I was advised to use a cable for initial setup of my home wireless network. I was able to get into the router to set all the passphrases and wireless security settings, etc. My ISP is PPPoe and I have entered both the UserId and Password that my ISP provided. However, upon clicking on the wireless icon, my system states I am connected but the status screen shows "No internet access". I have no problem connecting to the Internet when the cable runs from my DSL modem into my computer, so it's something to do with the router blocking it now.
My ISP does not support my Linksys router, of course, and they tell me I need to contact the manufacturer telling me the router needs to be set up as a 'bridge" ??? There is no mention of anything like this in the manual and I do not know if there is a setting on the router that is somehow blocking my being able to get an internet connection. This is all still with cables attached. Again, I seem to be able to 'connect' to the wireless network but I now cannot get to the Internet thru the router...
View 4 Replies
ADVERTISEMENT
Sep 1, 2011
i want to block all internet access on all my computers from the time range of 9 PM to 8 PM. Yes, that gives 1 hour of internet access per day. However, it seems that there are certain rules of the router that won't let me do this. It seems I can't make 2 different policies for PC's within the same IP range (192.168.1.0 to 192.168.1.254) , it gives me the error: "The values you entered are invalid. Please try again."every time I try to do so. And when I try to give the time range from 9 PM to 8 PM it gives an error stating that the end time must be bigger than start time. I am using the WRT54GL with firmware v4.30.7.
View 5 Replies
View Related
Aug 26, 2011
I had configured the AAA server on CoovaAP and was able to access the internet.I had configured the user name and password as a "testuser" and "password" respectively. With that user id i used to access the Coova AP router and internet.Now i want restore the WRT54GL firmware on Lynksys router. But with the used id and password which i had configured the router is not at all accessible. So i did 30-30-30 reset on the router 2-3 times. Now i can see openwrt login page with 192.168.1.1 IP address. It is asking for user id and password. I tried all the combinations of user id and password, but no luck. I browsed some link on the internet and some people have recommended that default user id as a "root" and blank password. But with that also the router is not accessible. I cant to do much on the router untill i will log in to router. I have spent lot of time on this. How to restore back the original WRAT54GL firmware on my router. Anyhow i want WRAT54GL firmware on Lynksys router
View 4 Replies
View Related
Jul 3, 2012
We have received from a customer of us an WRT54GL box configured with a Coova software. This Wifi router was supposed to be a Wifi hotspot, but was not configured by us. This box is able, on startup, to get an IP by DHCP, to touch a remote Radius server, and so on (we "tcpdump" the Internet traffic, and we saw DNS requests, radius requests, ...)...
But, we are unable to connect to this box,by SSH or by HTTP, either by plug-in PC to the Internet RJ45 or the LAN RJ45. It has no IP as 192.168.1.1. Instead, it was configured to have 192.168.1.1 as gateway.
Of course, we have no doc on previous install, but only the admin/root password for SSH.We are afraid to lose the config (coova, ...) if we perform a hard reset.What is the best way for connecting on this box ?
View 1 Replies
View Related
Aug 26, 2011
I had configured the AAA server on CoovaAP and was able to access the internet.I had configured the user name and password as a "testuser" and "password" respectively. With that user id i used to access the Coova AP router and internet.Now i want restore the WRT54GL firmware on Lynksys router. But with the used id and password which i had configured the router is not at all accessible. So i did 30-30-30 reset on the router 2-3 times.
Now i can see openwrt login page with 192.168.1.1 IP address. It is asking for user id and password. I tried all the combinations of user id and password, but no luck. I browsed some link on the internet and some people have recommended that default user id as a "root" and blank password. But with that also the router is not accessible. I cant to do much on the router untill i will log in to router. I have spent lot of time on this. how to restore back the original WRAT54GL firmware on my router. Anyhow i want WRAT54GL firmware on Lynksys router.
View 1 Replies
View Related
May 29, 2012
I got an Linksys WRT54GL-DE and my problem is,that someone manipulates the router.Is there any chance to protect the router in that way,that is not possible to reset the router by using the Reset-ButtonNOR by the Linksys software-tool?Especially the software-tool is the problem - I am afraid,that somebody reset / manipulate the router by using the software.
View 3 Replies
View Related
May 23, 2012
I own an AG214 ADSL2 router that I use for my desktop PC. I now however also have a WRT54GL for wireless connection. I connected the WRT54GL to my AG214 via ethernet. Everything works fine, I have wifi and I can use it to connect to the internet. However when I go to my router (192.168.x.x) I can't seem to be able to find a wireless tab to configure my wifi settings. The network right now is unsecure and has a default name (linksys). How do I access my wireless settings? When I access my router it does go to the AG214, do I need to access the WRT54GL? If so, how do I do that?
View 4 Replies
View Related
Jun 7, 2011
setting up my new WRT54GL.this is my first encounter with a wireless router, though I've had 3 previous Linksys (hardwired) routers.I have to say, given that they give virtually no Mac support, it was a breeze….just plugged it in to my cable modem and my laptop and - boom - on the net on my first try!I'm able to access the router via it's web-based system and can now "tweak" with settings, but I'm running in to a lot of "tweakable" settings that I'm not familiar with.
First my setup. I have; (a.) 3 desktop Macs and a Samsung TV hardwired to the four Ethernet ports and (b.) my Mac laptop accessing the router via Airport Extreme wifi. All are happily accessing the web.But I realize that the reason that "(b.)" is accessing the web is that I've changed no default settings in the router and, not only can *I* access the router via wifi, but probably anyone driving down the road or sitting out in front of my house can access the web via my wifi. And I'd like to change that.I'm *guessing* that the router settings i need to change lie in the "Wireless Security" area of the router? And it's here that I'm running in to a lot of "tweakable" settings that I don't understand.But let me give an example of what I would *like* to accomplish.
Let's say that there are 3 different laptops…."A", "B" and "C". All 3 are Macs and running Airport Extreme.Now, "A" is my laptop, sitting here on my desk next to the router. As i leave Airport always turned on, I want "A" to *always* have access to the routers wifi *without* having to enter a username/password, i.e. when i turn "A" on, it's wired.Now "B" might be the laptop of a friend who happens by the house and need access. They would need to find my network on their laptop and then i would need to give them a password to let them get on .And finally, "C" is the guy I don't know out in the street whom I want to *never* have access to my network.So my question then is, can I accomplish this by changing settings in "Wireless Security" on my router and how/what would I change?
View 9 Replies
View Related
Sep 7, 2011
I recently had to unplug my Linksys WRT54GL wireless router when doing some rearranging and now i'm unable to get a internet connection. I've confirmed the modem is actually working by connecting my laptop directly (which worked), but when I connect the Linksys WRT54GL wireless router to my modem the internet connection goes away. The connection is lost when connected via wireless and hardwired to one of the back ports. I've tried resetting the modem, router and computer and read every forum out there trying to find something, but i'm still stuck.
View 5 Replies
View Related
Nov 19, 2012
My WRT54GL Linksys modem has me stumped, it will not connect no matter what I try. it worked fine until just recently after a power outage; everything seems to be working perfectly fine hardware wise; the router shows a solid power led and network activity on WLAN, Ethernet, and Internet. I've tried soft resets and factory reset, clearing my caches, releasing/renewing IPCONFIG.
The peculiar part is that it is not letting me access the web config at 192.168.1.1 while connected with the modem, however if I plug the router directly to my PC's ethernet port I can access the config; Itried updating the firmware this way but it didn't solve the problem. I have no more ideas.
Below is the IPCONFIG information with the modem and router hooked up:
Ethernet adapter Local Area Connection 2:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : NVIDIA nForce Networking Controller #2
Physical Address. . . . . . . . . : 00-04-4B-17-C2-1A
[Code].....
View 2 Replies
View Related
Mar 18, 2013
I have router linksys WRT54gl, in my office i have cpu, phones, cameras that connected to the router lately its very slow the whole package and i think the problem is in the router i reboot it several times didn't work?i see memory used : 90% ?can this be the problem?
View 2 Replies
View Related
May 24, 2012
I've been using my WRT54GL for a long time now, without problems. Then suddenly last night, it stopped working. Now my girlfriend said she's pushed the Cisco Systems logo/button on the front of the router (which is now orange), but that's tho only thing that's been touched. When I plug the cable straight from the computer to the internet souce, I get connectivity. I've looked at a lot of guides now, but all of them require me to turn of the modem - which I cannot do, as it's a centralized modem in my appartment block. All I have on my site of things is an internet plug in the wall. What can I do to regain my wireless internet ?
View 9 Replies
View Related
Sep 18, 2011
I just bought a WRT54GL which is working perfectly. I needed it to extend my home network for my kids (I have not a very fast internet connection and my kids are eating all of it... With the WRT54GL I can choose how much they can have. So my own network has a netgear modem and a netgear wifi access point which is in this network : 192.168.0.x.
This network is not blocked in any way (just password protected). For my kids network, the WRT54GL gives addresses in this network : 192.168.1.x and is limited in speed. Everything is perfect, I have internet connection on both of my network, There is just the problem that I cannot access my printers, my servers, my computers.... that are on the 192.168.0.x network from 192.168.1.x. Is there a solution ? I already tried to force the WRT54GL to go to 192.168.0.x network but no more connection. Should I "bridge" the two networks ? How can I do it ?
View 1 Replies
View Related
Mar 11, 2012
2 routers (only one in use at a time!):
(A) Linksys BEFSR41 v3.1 Etherfast Cable/DSL Router w/ 4-Port Switch
(B) Linksys WRT54GL v1.1 Wireless-G Broadband Router w/ 4-Port Switch
Both routers are set to provide DHCP.DSL modem: Verizon Westell Wirespeed B90-210015-04 I have no idea whether this modem is also a router, but everything used to work. OS: Windows 7 Professional N x64, SP1 My computer has two ethernet ports, but only one is in use at a time. I also have VMWare Workstation installed, so there are a couple virtual adapters in the mix, but VMWare is not running during any of these tests.Yesterday (Sat, 10-Mar-2012) I replaced my old router (A) with the new one (B). The A router has been working fine for many years; I just needed wireless access. After the initial setup, the B router worked fine, using hard lines connected to the switch ports, and the wireless access features (laptop and Android phone) - for about a day. It suddenly dropped the internet connection early this afternoon, Sun, 11-Mar-2012, ~1220hrs PDT. I heard it go out because I was streaming NPR at the time.Using the B router, my desktop computer (connected via a wire) can still talk to my laptop (wireless), but neither of them can see the internet.When I swap back to the A router (wires only), it now has no internet connection either! But the desktop and the laptop (both wired) can still see each other via the (wired) router.When I remove the router from the network and connect the DSL modem directly to my desktop computer, I have internet access; it works fine! But not if a router is in the circuit.
(1) Router B seems to work because my wired desktop and my wireless laptop can communicate locally.
(2) Router A still works because my desktop and laptop can communicate with each other using a wired network hosted by the A router.
(3) The DSL modem seems to work because my desktop has internet access when connected directly to the modem.
(4) Neither of the routers can communicate with the internet through the DSL modem.
I spent an hour in a chat with Verizon tech support. I've power-cycled everything. I've reset both routers to default specs and reconfigured them. I've reset the DSL modem via its button. I've used different cables. It appears that neither of the routers can successfully communicate through the DSL modem to the internet. But they both used to. Why would it just suddenly stop connecting through the modem?
Scenarios:
computer <-> DSL modem <-> internet | works!
computer <-> either router <-> DSL modem <X> internet | NoGo
desktop <-> either router <-> laptop | ping OK
ipconfig /all results when connected directly to the DSL modem (internet connected):
Windows IP Configuration
Host Name . . . . . . . . . . . . : Serenity7
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]....
View 5 Replies
View Related
Aug 6, 2011
My house was in the middle of a lightning storm today while I was out and I came back to no internet. Figgured it was just the phone lines down, but connectiong directly to the modem I found I had connectivity. The WRT54GL (flashed with DD-WRT) doesn't pick up the WAN IP, I've checked with multiple ethernet cables, 2 different modems (all of which work fine with our computers, providing connectivity) and am currently using the router that the WRT54GL displaced ~8 years ago. I'm assuming it's just dead, but wanted a second opinion... kinda odd that a surge would have come through the phone line, through a DSL modem and killed the WAN port of the router instead of taking out the modem?
View 2 Replies
View Related
Mar 29, 2013
i have just purchased my wrt54gl two weeks ago. Setup was a breeze and it worked flawlessly until this morning when i noticed i had no internet. The ethernet light on my modem, when connected to router (Ubee 10C035 3.0/Comcast ISP) will blink 2-3 times then stop for a half second then blink 2-3 times and so on. Plugged ethernet cable from pc directly into modem and my desktop connected to the 'net fine and light was blinking normally(constantly) again. A few power cycles/reset of the Router to defaults but no luck.
View 3 Replies
View Related
Nov 28, 2012
I just got my fathers old linksys WRT54GL. I Have resat everything, and made my own name, password etc.When i try to connecet, i can get on the network, but there's no internet connection. Even when i put an ethernet cable between, it does the same. i have internet connection when i connect directly to the router though.
View 1 Replies
View Related
Apr 26, 2012
My ISP provides me internet by pppoe connection.When testing the connection with the router i get 30 mbps.When testing the conection without the router, cable conected to laptop i get 60 mpbs.
View 1 Replies
View Related
Jul 27, 2011
I had the router working fine then last night for some reason it dropped 2-3 (all of them currently on) internet, while online.I can connect wireless just fine to the router but get no internet, when i plugged into the router directly i still go internet, but when i connect the modem directly into the laptop i get internet so it is not the modem. I have tried to reboot the router and modem to no avail.i can access the routers page wirelessly and change stuff but just don't get any internet and the signal strength is excellent.
View 1 Replies
View Related
Nov 24, 2011
I've had my WRT54GL for a few months now and have two computers that are wired and 3 that are wireless. I started having problems with conflicting IP's a couple days ago on one of my wired computers which was set for auto DHCP so I changed the settings and made it a static IP, this is when the problem started. I have Network Magic on all computers and even though it says I'm connected to the internet and the network, I am not able to get online. My other wired computer has been on Static IP for months and works fine.
View 9 Replies
View Related
Jan 15, 2013
I want to block sites like facebook during my workday but allow the rest of the internet.
The attached settings block facebook as desired during the filter times but after 6:30pm the filter expires and the entire internet is blocked (not just facebook). All of my browsers act as if they are hanging and won't load pages until I disable the filter.
I've also tried creating two different filters (one at a time). The first allowed full internet access all the time and the second allowed access the opposite times of the work filter. But to no avail.
View 2 Replies
View Related
Aug 15, 2012
We have a Model WRT54GLWireless-G router. At least once a day it loses it's internet connection. All computers that are wired to the switch that is connected to it lose their internet as well as any wireless devices. I have to manually power-cycle the router to get internet back.
View 9 Replies
View Related
Jun 9, 2011
In our house we use a Linksys WRT54GL router. When I am connected to the router via a cable I can play an online RPG without any problems.I recently connected an acecss point to the router ( a belkin N1 ). Even if I am connected with a cable to the accesspoint, which is connected to the router by cable as well, I get huge lag spikes about every 10 seconds while playing the game.
View 10 Replies
View Related
Aug 26, 2011
Few months back i had upgraded my Lynksys router with Coova AP firmware. Everything was working fine.I had configured the AAA server on CoovaAP and was able to access the internet.I had configured the user name and password as a "testuser" and "password" respectively. With that user id i used to access the Coova AP router and internet. Now i want restore the WRT54GL firmware on Lynksys router. But with the used id and password which i had configured the router is not at all accessible. So i did 30-30-30 reset on the router 2-3 times.
Now i can see openwrt login page with 192.168.1.1 IP address. It is asking for user id and password. I tried all the combinations of user id and password, but no luck. I browsed some link on the internet and some people have recommended that default user id as a "root" and blank password. But with that also the router is not accessible. I cant to do much on the router untill i will log in to router. I have spent lot of time on this.
how to restore back the original WRAT54GL firmware on my router. Anyhow i want WRAT54GL firmware on Lynksys router. Can somebody tell me how to achieve this?? Or atleast what user id and password should i try to log in to router?I tried to use telnet command on the router (Connected router to linux based computer with ethernet cable). But telnet also not working. It is not asking for password, and it saying disconnected.
View 1 Replies
View Related
Jan 3, 2013
I just recently picked up a DIR-655 to replace my WRT54GL, hoping that I could get a better stream in my house. The house is 100 years old with plaster and lathe, and I can't relocate the modem and router. So I figured I could use my old WRT54GL as a signal booster/access point on the second level of the house. I read through a couple of guides, and I could get the router to broadcast the signal with full bars, and I could attach to it, but I didn't get any internet. The D-Link is a DIR-655 with firmware 2.10NA. The Linksys is a WRT54GL with Tomato 1.25. Here are a couple screenshots for the DIR-655
View 1 Replies
View Related
Aug 27, 2012
I got an Fritz Box from my new Provider to connect to the internet using Fiber To Home. the box is now im my living room and also acts as an WLAN Router. I would like to configure my WRT54GL which in located in my office from a router to a repeater to establish a WLAN bridgde.
View 3 Replies
View Related
May 2, 2012
I have both a Sony XBR52HX909 and a Sony BDP-S580 connected to my router (WRT54GL)via ethernet. When I try to connect to the internet, both show the wired connection as good but neither can connect to the internet. The BDP-S580 also has wireless connectivity, but it can’t connect to the internet wirelessly. I have two desktop computers connected via ethernet and two laptops connected wirelessly to the same router and all have internet connectivity. I have tried the “auto” settings on the TV and Blu-Ray player and also tried entering the network information in manually. I still can’t connect to the internet.
View 5 Replies
View Related
Feb 5, 2011
Last week suddenly my internet connection failed. I have tried several times to establish the wireless internet connection. Everytime when i tried to do this, i get the message 'can not get IP address'. Already tried to upgrade the firmware but still same message appears.
View 4 Replies
View Related
Apr 14, 2010
I want to use my router to boost the signal to the 2nd floor of my house, and Im having some problems.When I connect my router to the web application to change restore it to manufaturer setting the router keeps broadcasting my old SSID. The laptops in the house pick up that signal. I want to reset my router so it can broadcast my new network.
View 2 Replies
View Related
Nov 10, 2011
I have Wireless-G Broadband router Model WRT54GL. Everything is all setup correct but consoles and handhelds can't get the IP address even if there connected to the router. It isn't intill I turn off and then it back on does it get the ip address.
View 2 Replies
View Related
Jun 20, 2012
I'm trying to use a WRT54GL with U-Verse. The problem is that the router does not get a connection to the modem. It can't ping the modem, and it doesn't show up on on the list of devices connected to the modem. DHCP assigns an IP address of 127.0.0.1, which is outside the range of the modem [192.168.1.1 ... 192.168.1.253]. The router is also showing a default gateway of 0.0.0.0, and a subnet mask of 255.0.0.0. (And yes, I have released and renewed the lease, rebooted the modem, and reconnected the modem.) The router WAN side is set to DHCP, and the operating mode was changed from gateway to router (the gateway setting doesn't work either, for that matter).
View 9 Replies
View Related
Mar 16, 2011
I currently own a LinkSys-WRT54GL 802.11a/b/g wireless router, and my ISP is Comcast Cable providing me with 15 Mbps (that's bits per second, I believe) download speed. I am wondering if there is any benefit with using an 802.11n wireless router to access the Internet? The maximum theoretical speed of the WRT54GL router is 54 Mbps (802.11g), which is faster than the 15 Mbps provided by my ISP.
I know that 802.11n has a max bandwidth of 300 Mbps, and it would work for intra- house transfers, such as streaming video from one computer to another.
But is there any benefit to 802.11n for Internet activity, such as web browsing, gaming, and streaming video from Netflix.
View 3 Replies
View Related
May 8, 2013
I have a problem with my linksys WRT54GL router. I entered here [URL] and i set it up, i can connect to internet on my PC and wireless works great but i can't set wireless password and name. When i go to the wireless tab, i write the new name but when i hit seve setting i get disconnected from internet. I try to go to status and click on Connect tab, when is connected internet works but the name and the password of the wireless that i set earlier is reset to default. What do i have to do to set name and password and have internet at the same time.
View 7 Replies
View Related
