D-Link DIR-655 :: Use Linksys WRT54GL Router As Access Point With It?
Jan 3, 2013
I just recently picked up a DIR-655 to replace my WRT54GL, hoping that I could get a better stream in my house. The house is 100 years old with plaster and lathe, and I can't relocate the modem and router. So I figured I could use my old WRT54GL as a signal booster/access point on the second level of the house. I read through a couple of guides, and I could get the router to broadcast the signal with full bars, and I could attach to it, but I didn't get any internet. The D-Link is a DIR-655 with firmware 2.10NA. The Linksys is a WRT54GL with Tomato 1.25. Here are a couple screenshots for the DIR-655
In our house we use a Linksys WRT54GL router. When I am connected to the router via a cable I can play an online RPG without any problems.I recently connected an acecss point to the router ( a belkin N1 ). Even if I am connected with a cable to the accesspoint, which is connected to the router by cable as well, I get huge lag spikes about every 10 seconds while playing the game.
I got an Fritz Box from my new Provider to connect to the internet using Fiber To Home. the box is now im my living room and also acts as an WLAN Router. I would like to configure my WRT54GL which in located in my office from a router to a repeater to establish a WLAN bridgde.
Any issues connecting an N access point via an ethernet cable to a G router?I currently have a wrt54gl router in one room (where it's connected by cables to various devices). I'm usually in another room and connect via wifi with other devices. Internet speeds over wifi are fine, but speeds are too slow when transferring files from wifi devices to other computers (windows file sharing).
I'm thinking of running a cable through a wall from the wrt54gl room to the other room and connecting a small N router, in access point mode. I'd then connect to the N access point and, through it, to the main router and other devices in the network.All wifi devices can run N.
Are there any issues in doing this? Anything I should know about configuring this? From other questions, it's not clear if I should use the same SSID for both routers. For that matter, should I turn off wifi on the wrt54gl?
I just bought a WRT54GL which is working perfectly. I needed it to extend my home network for my kids (I have not a very fast internet connection and my kids are eating all of it... With the WRT54GL I can choose how much they can have. So my own network has a netgear modem and a netgear wifi access point which is in this network : 192.168.0.x.
This network is not blocked in any way (just password protected). For my kids network, the WRT54GL gives addresses in this network : 192.168.1.x and is limited in speed. Everything is perfect, I have internet connection on both of my network, There is just the problem that I cannot access my printers, my servers, my computers.... that are on the 192.168.0.x network from 192.168.1.x. Is there a solution ? I already tried to force the WRT54GL to go to 192.168.0.x network but no more connection. Should I "bridge" the two networks ? How can I do it ?
My home network currently has a Linksys router (essentially acting as a wireless access point) in a distant part of the house connected to my main router, a Netgear WNR2000, and this configuration is working fine.
I want to replace the main router with a new D-Link DIR-655 (better parental controls). When I swap in the new router and get the cables plugged in in the same manner as they are in the Netgear router, computers connecting wirelessly to the Linksys router can no longer access the Internet.
The Netgear router is set up with an IP address of 192.168.4.1. The Linksys is 192.168.2.1, and the D-Link is at the default 192.168.0.1.
Few months back i had upgraded my Lynksys router with Coova AP firmware. Everything was working fine.I had configured the AAA server on CoovaAP and was able to access the internet.I had configured the user name and password as a "testuser" and "password" respectively. With that user id i used to access the Coova AP router and internet. Now i want restore the WRT54GL firmware on Lynksys router. But with the used id and password which i had configured the router is not at all accessible. So i did 30-30-30 reset on the router 2-3 times.
Now i can see openwrt login page with 192.168.1.1 IP address. It is asking for user id and password. I tried all the combinations of user id and password, but no luck. I browsed some link on the internet and some people have recommended that default user id as a "root" and blank password. But with that also the router is not accessible. I cant to do much on the router untill i will log in to router. I have spent lot of time on this.
how to restore back the original WRAT54GL firmware on my router. Anyhow i want WRAT54GL firmware on Lynksys router. Can somebody tell me how to achieve this?? Or atleast what user id and password should i try to log in to router?I tried to use telnet command on the router (Connected router to linux based computer with ethernet cable). But telnet also not working. It is not asking for password, and it saying disconnected.
I had configured the AAA server on CoovaAP and was able to access the internet.I had configured the user name and password as a "testuser" and "password" respectively. With that user id i used to access the Coova AP router and internet.Now i want restore the WRT54GL firmware on Lynksys router. But with the used id and password which i had configured the router is not at all accessible. So i did 30-30-30 reset on the router 2-3 times. Now i can see openwrt login page with 192.168.1.1 IP address. It is asking for user id and password. I tried all the combinations of user id and password, but no luck. I browsed some link on the internet and some people have recommended that default user id as a "root" and blank password. But with that also the router is not accessible. I cant to do much on the router untill i will log in to router. I have spent lot of time on this. How to restore back the original WRAT54GL firmware on my router. Anyhow i want WRAT54GL firmware on Lynksys router
We have received from a customer of us an WRT54GL box configured with a Coova software. This Wifi router was supposed to be a Wifi hotspot, but was not configured by us. This box is able, on startup, to get an IP by DHCP, to touch a remote Radius server, and so on (we "tcpdump" the Internet traffic, and we saw DNS requests, radius requests, ...)...
But, we are unable to connect to this box,by SSH or by HTTP, either by plug-in PC to the Internet RJ45 or the LAN RJ45. It has no IP as 192.168.1.1. Instead, it was configured to have 192.168.1.1 as gateway.
Of course, we have no doc on previous install, but only the admin/root password for SSH.We are afraid to lose the config (coova, ...) if we perform a hard reset.What is the best way for connecting on this box ?
I had configured the AAA server on CoovaAP and was able to access the internet.I had configured the user name and password as a "testuser" and "password" respectively. With that user id i used to access the Coova AP router and internet.Now i want restore the WRT54GL firmware on Lynksys router. But with the used id and password which i had configured the router is not at all accessible. So i did 30-30-30 reset on the router 2-3 times.
Now i can see openwrt login page with 192.168.1.1 IP address. It is asking for user id and password. I tried all the combinations of user id and password, but no luck. I browsed some link on the internet and some people have recommended that default user id as a "root" and blank password. But with that also the router is not accessible. I cant to do much on the router untill i will log in to router. I have spent lot of time on this. how to restore back the original WRAT54GL firmware on my router. Anyhow i want WRAT54GL firmware on Lynksys router.
I tried setting up a home network with my above Linksys router and can't connect to the internet now. I have the ethernet cable from my DSL Modem hooked into the ethernet port on the back of the Router. In port one, I have a cable which attaches directly to my laptop as I was advised to use a cable for initial setup of my home wireless network. I was able to get into the router to set all the passphrases and wireless security settings, etc. My ISP is PPPoe and I have entered both the UserId and Password that my ISP provided. However, upon clicking on the wireless icon, my system states I am connected but the status screen shows "No internet access". I have no problem connecting to the Internet when the cable runs from my DSL modem into my computer, so it's something to do with the router blocking it now.
My ISP does not support my Linksys router, of course, and they tell me I need to contact the manufacturer telling me the router needs to be set up as a 'bridge" ??? There is no mention of anything like this in the manual and I do not know if there is a setting on the router that is somehow blocking my being able to get an internet connection. This is all still with cables attached. Again, I seem to be able to 'connect' to the wireless network but I now cannot get to the Internet thru the router...
I got an Linksys WRT54GL-DE and my problem is,that someone manipulates the router.Is there any chance to protect the router in that way,that is not possible to reset the router by using the Reset-ButtonNOR by the Linksys software-tool?Especially the software-tool is the problem - I am afraid,that somebody reset / manipulate the router by using the software.
i want to block all internet access on all my computers from the time range of 9 PM to 8 PM. Yes, that gives 1 hour of internet access per day. However, it seems that there are certain rules of the router that won't let me do this. It seems I can't make 2 different policies for PC's within the same IP range (192.168.1.0 to 192.168.1.254) , it gives me the error: "The values you entered are invalid. Please try again."every time I try to do so. And when I try to give the time range from 9 PM to 8 PM it gives an error stating that the end time must be bigger than start time. I am using the WRT54GL with firmware v4.30.7.
I own an AG214 ADSL2 router that I use for my desktop PC. I now however also have a WRT54GL for wireless connection. I connected the WRT54GL to my AG214 via ethernet. Everything works fine, I have wifi and I can use it to connect to the internet. However when I go to my router (192.168.x.x) I can't seem to be able to find a wireless tab to configure my wifi settings. The network right now is unsecure and has a default name (linksys). How do I access my wireless settings? When I access my router it does go to the AG214, do I need to access the WRT54GL? If so, how do I do that?
setting up my new WRT54GL.this is my first encounter with a wireless router, though I've had 3 previous Linksys (hardwired) routers.I have to say, given that they give virtually no Mac support, it was a breeze….just plugged it in to my cable modem and my laptop and - boom - on the net on my first try!I'm able to access the router via it's web-based system and can now "tweak" with settings, but I'm running in to a lot of "tweakable" settings that I'm not familiar with.
First my setup. I have; (a.) 3 desktop Macs and a Samsung TV hardwired to the four Ethernet ports and (b.) my Mac laptop accessing the router via Airport Extreme wifi. All are happily accessing the web.But I realize that the reason that "(b.)" is accessing the web is that I've changed no default settings in the router and, not only can *I* access the router via wifi, but probably anyone driving down the road or sitting out in front of my house can access the web via my wifi. And I'd like to change that.I'm *guessing* that the router settings i need to change lie in the "Wireless Security" area of the router? And it's here that I'm running in to a lot of "tweakable" settings that I don't understand.But let me give an example of what I would *like* to accomplish.
Let's say that there are 3 different laptops…."A", "B" and "C". All 3 are Macs and running Airport Extreme.Now, "A" is my laptop, sitting here on my desk next to the router. As i leave Airport always turned on, I want "A" to *always* have access to the routers wifi *without* having to enter a username/password, i.e. when i turn "A" on, it's wired.Now "B" might be the laptop of a friend who happens by the house and need access. They would need to find my network on their laptop and then i would need to give them a password to let them get on .And finally, "C" is the guy I don't know out in the street whom I want to *never* have access to my network.So my question then is, can I accomplish this by changing settings in "Wireless Security" on my router and how/what would I change?
I have just moved into a new apartment that has a free wifi connection the problem is that my apartment is in the basement at the completly opposite side of the office and i cant get a strong enough signal to connect to the internet and im not very good with computers. the first time i tride setting up the repeater i was able to connect everything and get online but it had changed the ssid and when i tride to change it bacck to its origanil name i lost my internet connection and have not been able to get access the internet again.
Tech Support Guy System Info Utility version 1.0.0.2 OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit Processor: AMD Duron(tm) processor, x86 Family 6 Model 8 Stepping 1 Processor Count: 1 RAM: 479 Mb Graphics Card: S3 Graphics ProSavageDDR (Microsoft Corporation), 32 Mb Hard Drives: C: Total - 24385 MB, Free - 3678 MB; D: Total - 13776 MB, Free - 13649 MB; Motherboard: , KM266-8235 Antivirus: None
How do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
I just bought an LG Bluray DVD player (BD390) which is unable to find the access point in my home network.My router is a WRT54G, ver. 2.2, running firmware: Ver.4.21.1. My home network uses high speed cable with two computers on the wireless network, all working with no problems.The router is on the second floor but the two computers and the new BD390 are on the first floor - about 35 feet away. I have the wirelss security set to none and use only the specific computer MAC addresses to allow connection to this network.
I found directions in the forum for a setup using the LG BD390 but with a different Linksys router. I changed the security to WPA (AES); the Beacon interval from 100 to 75; the Fragmentation Threshold from 2346 to 2304; and the RTS Threshold from 2347 to 2307. The DVD wireless connection still failed to find my network. There is a "Push button" connection feature on the BD390 setup which I tried, but the only "button" on the router I could find was in the basic wireless setting, a green icon for the wireless SSID setup. No connection was made there either.
The recommendation connection from the LG manual is for a network cable, but that would be over 50 feet and a real pain to connect, so I would prefer WiFi.
I want to set D-Link DIR 655 as Access Point. For your information , I'm using D-Link 2750U (modem + router) as primary wireless router. how do I set D-Link DIR 655 as Access Point ?
I have a D-Link DIR-655 with an usb dongle DWA-140. I used to work with a Sitecom WL-341 router.I want to use the Sitecom WL-341 as an acces point to improve my wireless range at the top floors of my house.
What I want to create:
- The modem connects to the D-Link router;
- The D-Link router makes a wireless connection with the Sitecom router;
- The Sitecom router is now an acces point;
- I connect the Sitecom router with a cable or wireless to my desktop PC.
I don't want a cable in my house that connects the D-Link with the Sitecom. If I do this, not only will people get hurt getting up the stairs because of the cable lying there, it also isn't a pretty sight...
I have a DIR 655 which I am trying to use as a pure access point for a network based on a Comcast SMC Modem/Router On the DIR 655 I have the DHCP turned off and on the Internet Connection I have given the DIR 655 a static address of 10.1.10.2 with Gateway and Primary DNs 10.1.10.1 (The SMC is 10.1.10.1) I have the DIR 655 connect to the SMC Lan to Lan. DIR 655 is G only to deal with and IPAD issue....
The wireless devices get an internet connection BUT... I can only contact the DIR 655 wirelessly the SMC does not show the DIR 655 as connected I can not ping the DIR-655 from the SMC. I can " see" the static addresses I have given to two network cameras but they don't not respond to Port Forwarding I have assigned at the SMC (that is more for info as I realize that might be a SMC issue) . How to make the DLIK visable to the wired network.
A friend of mine has a network with the following setup: D-Link DSL-2500U for ADSL, connected straight into a Telkom DG834GUv5 (locally rebadged Netgear) which has 2 PCs connected via cable, and 2 laptops via Wireless. A cable runs from the Telkom into a standard IPLink switch, which merely extends a cable into a D-Link DIR-615 running DD-WRT that has 2 computers connected, and shares wireless to a couple laptops.
At the moment the network is somewhat unstable, and recently the Telkom router has been giving serious problems, even after resetting to default. I want to try make the network a bit simpler and more stable. Firstly, I want to remove the IPLink switch, which merely extends the cable. Is an Ethernet Coupler what I need? Both cables are definitely under 100m combined (probably under 50m).
Now the big thing is a replacement for the Telkom (rebadged NetGear). Should I get another D-Link DIR-615 or is there a better solution? Their budget is between $40 and $60 US. Is it best to stick to the same brand, considering both devices are D-Link at present?
setting up wifi network in my office. my complete set up right now. the main problem is how to setup my access points . Okay so here it is.
I have 3 - 4 PCS in my office out of which My machine is the main machine and everything is setup on this. so for networking what i have done is i am using a TP link router model TL-WR941D. i had got it configured from an engineer. A cable from my internet modem goes into the blue port of this router(WAN) and my PCs are connected via the LAN port of the router . so everything is working fine right now the local network and internet on all PCS and my laptop also connects through the wifi and is able to access other pcs and also the internet.
To have better signal strength on other floors of the building my engineer had installed 2 access points. They are TP link model Tl-WA901ND. yesterday i updated the firmware of my main router and the settings were some how lost but i managed to set it back to working state using the quick setup utility. so my router and wifi is working fine. But now my access points have stopped sworking . i mean i am not able to get better signal strengths thorugh them. i am assuming theirs ettings /ip etc are lost. now i have no idea how to setup these access points to be used again as part of my wifi network. I looked on the internet but nowhere the thing has been explained in detail. how can i configure my access points/repeaters agaain? i am stuck and engineer is not available for nest few days and my officee internet is suffering.
I wish to turn my TP-Link wireless router into an access point but can't figure out how to do it. I have tried several times but without any success. Below are my information about my main router and the router I want to turn into an access point:
1- Main Router: TP-LINK 3G/4G Wireless N Router 300Mbps - Model No. TL-MR3420. url..
2- Router I wish to turn into an access point:TP-LINK Wireless N Router 150Mbps - Model No. TL-WR740N. url...
I have a WAP54g hardware version 1.0.I install de last firmware on this access-point but, this access-point reset automatic after a random time..It’s it possible to downgrade de firmware from this access-point?
Have a WRT320N router at one end of the house in the basement. Would like to boost signal to other end of the house. Which product should i use, an access point or a range extender? My house is also wired with Ethernet cable and I could plug the access point into an Ethernet port at the end of the house where the signal is weak.
I've got a AP WAP54G. I've managed to get into the configuration page and rename my router and set a WPA2-Personl password.
The issue I'm facing is that when me and my roomate try to connect to the router at the same time, it shows the laptop that connects second as one that has 'limited connectivity' and hence cannot use the internet. The 1st laptop however works fine! The settings for the router have all been left to default.
I'm not sure, but does this problem have anything to do with the fact that the router in configured with a static IP. If so, then there is another issure which is that whenever I try to change it from static to automatic/dynamic IP, the page fails and the router doesn't even get connected to the configuraion page(192.168.1.245) after that. The only way to get that page again is the reset the router.
Also I'm not able to directly get into the config page when I connect my router to my laptop via lan. I need to change the LAN IP to 192.168.1.x where x is >1.
What I want to do is the opposite of most configurations. I live on a small island with only one DSL connection. The modem is wired connected to a WAP54G Access point. To extend this access point want to use a WRT54G.
I'm using a WRT120N and have had no problems connecting most wireless devices, but a Nintendo DS and DSi owned by my family are unable to connect to the access point. My wireless security mode is disabled, network mode is set to mixed, SSID is the same as on the DS/DSi, Channel width is 20Mhz only, Standard channel is set to 6, but I tried using channel 1 and 11 without success, SSID broadcast is enabled.
I've tried every work-about I could find and always get the 51300 error code, and am at a loss as to what else I can try to get the devices to connect to the access point.
