Belkin Routers :: F5D8231-4 Intermittently Stops Broadcasting?
Mar 19, 2013
My F5D8231-4 (N1 Wireless Router) keeps shutting down its wireless broadcast. If I reset back to factory settings it comes back on but then I have to setup again.
View 1 Replies
ADVERTISEMENT
Jan 11, 2013
Lately I notice my router is very very slow. most of the time I cannot use my ipad or it takes too long and sometimes never finishes downloading a web site. I called Belkin support, and I was told that I need to update and configure, and to do that I have to pay more than what my router cost.
View 3 Replies
View Related
Feb 27, 2013
I recently replaced my old Belkin Pre-N router with a newer N router. Still, the newer one is only less older than my Pre-N Belkin router that I had sitting around but never opened and installed (F5D8231-4). Anyway, I finally decided to set it up. I was trying to log into the router to set security settings and to update the firmware but when I type the IP address into the address bar in IE or Firefox, it is partially blank. There are no functional buttons. Only the Belkin logo on a gray background with a couple of emtpy boxes where it looks like functional buttons or tabs should be. how to get to a working screen with functional buttons?
View 1 Replies
View Related
May 24, 2013
How do set a wifi password? Have been operating for years without a wifi password but now I want one.
Have an N1 wireless, F5D8231-4 Router setup, 192.168.2.1
View 1 Replies
View Related
Jan 24, 2013
I have an N1 Wireless Router (F5D8231-4 ver 2). It is setup with WPA/WPA2-PSK on and links to a Windows Laptop and an iPod Touch perfectly. I cannot get my new Samsung Note 10.1 (GT-N8000) connected. I have tried changing the router to WEP 128bit and even no security. The Samsung links perfectly to my neighbours Thomson Wireless Modem/router with no security. The Belkin N1 is recognising the android trying to link and assigns an IP. The Samsung instantly sees the Belkin network ( says " very strong signal") & tries to connect. It saves the network but gets stuck trying to obtain an IP address & reports "network disabled" and "weak signal".
View 1 Replies
View Related
Feb 22, 2013
FSD 7632-4 Router.Have this 2006 router which has started dropping the connection and/or slowing it down intermittently. Before I replace it, would like to update the firmware. Have downloaded the update but cannot log-in on the setup utility page as I cannot remeber my password (apparently it is not set to blank!).
View 1 Replies
View Related
Oct 1, 2011
i have 2 DIR 615 routers which both stop broadcasting SSIDS. Ive had only one connected at a time, thinking it was a bad router, but both behave the same way. Is this a known issue or something ? What happens is, after some time (it varies..sometimes 3hours..sometimes longer), the router stops broadcasting the ssid, and I can no longer connect any of my wireless devices to it. The hardwired connection does work (I have a server connected to it, and it appears to work).The only settings I have changed is my SSID name, and wpa2 password. I've set up one virtual server to port forward requests to the server. Thats it. Nothing complex or anything. And both routers behave the exact same way, meaing they stop broadcasting the SSID.
View 8 Replies
View Related
Mar 2, 2011
Internal network (LAN) works OK rock solid; only internet drops intermittently windows xp sp3 with latest updates wired connection
View 2 Replies
View Related
Jul 17, 2011
I have a problem with a wireless adaptor on a Toshiba Tecra (A11-1EE - PTSE0E-065052EN) running Windows 7.The wireless adaptor works fine but every now and again it will just stop working. The operating system says that the adaptor is turned off but it isn't. I've checked the driver but it is up to date.I have to disable the driver and then enable it again and then the adaptor begins to work correctly again.
View 4 Replies
View Related
Jun 20, 2011
I bought a DIR-655 (F/W v. 2.00NA) about 6 months ago. It worked well until a couple of weeks ago. Then it started to stop broadcasting WIFI signal without apparent reason. When it did so, I could still connect to it and internet with wired connection, but the WIFI scan does not show my SSID. If I reboot it (either through the admin interface, or just disconnect and reconnect the power), I would be able to reconnect to WIFI, but then WIFI will stop working again in about 8-10 hours. I am rebooting this thing 2-3 times a days and it is very frustrating. Curiously, I borrowed a N300 router to try out
View 10 Replies
View Related
Mar 30, 2011
I just bought a dlink 655 from amazon and for some reason the router stops broadcasting on wifi. I cannot connect to it through my laptop or ps3. The only thing that fixes this is removing the plug from the back of it and putting it back in, once i do this, the SSID shows up once again and all is well until the next day (or 2 days after)
View 2 Replies
View Related
Feb 9, 2013
I run a AirPort Extreme router. I have my F9K1106 range extender set up and working. works awesome. I get home from work the next day and the range extender seems to fall asleep , it won't pass any traffic. I power cycle it and its back up and running. this happens everyday no fail for a week now.
View 1 Replies
View Related
Sep 30, 2011
I have a linksys WRT54G that has been bugging out a lot. It stops broadcasting the SSID briefly and won't start again until it reboots. Annoying enough problem on it's own, but not my primary concern.My concern now is that when I tried to upgrade the firmware to the latest version (which I presume was causing the problems) the router now is essentiallyunresponsive. The upgrade was successful according to the control panel site, but ever since the required reboot as part of the upgrade process the router hasn't worked properly. 1) The power light blinks constantly rather than staying lit.2) When I plug directly into it sometimes I get access to local networks and other times I don't (limited connectivity). But I never get access to the internet if it's plugged into it as well.3) When I try to go to the control panel site (through the 192.168.1.1) the site wont loadGranted this router is old, but it was working fine other than dropping the broadcast every once in a while. It did need a firmware upgrade, but the upgrade seems to have been a bad choice
View 3 Replies
View Related
Dec 13, 2011
I have two DIR-655s. One is my main router, connected to my modem. The other, on the other side of the house, is set up as an access point. I followed this guide to set up my AP: [URL]
Both are are hard wired. I have both of them using the same SSID. Both are 802.11g only, have the same security mode, and key. The only wireless difference is the channel. One uses 6, while the other uses 11.
On initial setup, everything is fine, but after a few hours, the AP just seems to stop broadcasting a signal. I'm using "Wifi Analyzer" on Android to monitor it. When I look at the AP, the wifi indicator light is still on. If I log into it, change the channel, and press save on the "Wireless Settings" screen, it will broadcast for a few more hours before stopping again. The wired connect of this AP always seems to work (Xbox is hard wired to it).
AP Hardware Version: B1 / Firmware Version: 2.03NA
View 14 Replies
View Related
Dec 28, 2012
My OS is Windows 7 and I'm trying to setup my wireless g gaming adapter (F5D7330 v.2) and the install software continuously stops working once it says to plug in the adapter into the AC wall outlet.
View 2 Replies
View Related
Feb 8, 2012
I've got a DIR-825 RevB Firmware V2.06NA on a static IP wan connection routing to a SBS2008 server and 10PC's. The server is serving mail, web, and files. Router has virtual servers setup for http, https, smtp, imap, imapssl, smtpssl, pptp, remote desktop, and a few others.
Everything works fine, but the routers https forwarding stops running periodically about half an hour after reboot. The server's working fine, but it doesn't see the https request, it looks like the router is trying to serve the 443 request itself. After a router reboot everything is back to normal.
I've replaced the router with another dir-825 and it has the same issue.
View 3 Replies
View Related
Aug 18, 2012
I am trying to set up ADSL and WiFi in a country home. I have bought a DLink DSL-2640 modem-router for this. The device is connected to the ADSL, everything works fine. The device has a WiFi AP capability - I have set up the WiFi and I am accessing the network from 2 different iPads, 2 PCs and an Android phone. After a few hours of work I begin to notice that one of the iPads is taking to long to load pages - it even can't load the router's web interface. This goes on for 5-10 minutes or so, then it passes away. Same stuff happens to Android, but rarer. PC has this problem occasionally also, but rarest of all.
I am assuming that this is a problem of the device - ADSL and WiFi might be too much for it. I got a dedicated WiFi router (TP-Link WR740N), connected it to the DLink and turned off WiFi on the D-Link.
Same stuff happens. After a while the Internet stops responding - I can't load the router's web interface. Goes on for 2-10 minutes and passes. WiFi is functional, I can disconnect and connect a device, device obtains an address through DHCP.
I updated both devices to the latest official firmware. I tried switching WiFi channels, switched the router to g-only mode. EM interference is very unlikely since it's a country home and there are no wifi networks around.
View 2 Replies
View Related
Mar 12, 2008
I the only one who's WRT160N occasionally just stops broadcasting WiFi and have to reset the router to get it back?
View 9 Replies
View Related
Nov 10, 2011
The wireless drops specifically from my laptop constantly at random times. When the wireless drops in order for me to be able to reconnect i have to restart the router itself. There are also random times where the Wi-Fi stops broadcasting altogether. I have a computer connected via Ethernet and it does not lose connection during these times. All the computers are running Windows 7 and the Router is up to date on firmware.
View 5 Replies
View Related
Jan 10, 2013
I recently had to reset my router, back to factory default. The problem is after setting it up again and everything it's still somehow broadcasting the old network name. Alongside the new one.
View 9 Replies
View Related
Jul 12, 2011
I installed the RV220W Router in my office about 2 weeks ago and everything works perfectly for 3-4 days but then my connection drops out and the router must be restarted to restore connectivity. When I say the connection drops basically the internet connection drops out and my network connections drop shortly thereafter. Usually the wireless connections lose connectivity followed within a few minutes by the wired connections.
Is there something in my firewall settings that could cause this issue? I have checked with my ISP to verify there are no problems on their end.
View 12 Replies
View Related
Mar 10, 2012
My RVS 4000 v1 router firmware version 1.3.0.5 has been intermittently going off-line ... a reset of the power resolves the issue temporarly. My plan was to update the firmware but I haven't been able to download an uncorrupted version of the firmware file on the Cisco support site. The file downloads as a zip file but the winzip program says that the file is not in a valid zip format and cannot open it.
View 1 Replies
View Related
Oct 18, 2011
For eight months we have not had any problems with our new WRVS4400N (V2.0.2.1) connected to a Verizon/Westell 6500 to provide DSL internet for our network with DHCP on our server... No changes have been made to the router or modem since initial setup; but, then it started -- Our internet connection would drop intermittently. Sometimes every 5 or 10 minutes - sometimes every hour. Verizon has tested the lines which came up ok, then they sent a tech who changed the wire pair coming into the building for the DSL line and retested the lines which again came up ok, then they provided us with a new modem (now a Verizon/Westell 7500). After all that, the DSL still connects then disconnects intermittently. I am now wondering if the issue lies with the WRVS4400N.
View 2 Replies
View Related
Apr 26, 2013
(F5D9230-4 v5111 Belkin mimo router ) is version 5.02.08 the most up to date firmware for my router?
View 1 Replies
View Related
Apr 26, 2013
How do I setup my Belkin F7D1301 with a 16 port 10/100 switch so I can use the wireless on the Belkin and have the 16 port switch for my hard wires?
View 1 Replies
View Related
Mar 16, 2013
I have a problem with the RV042G V01 router manufactured 12/2012.
After router settings the router works fine without any problems. After 10 or 12 hours I got the message that the side could not be opened, while no DNS. I checked inside the router and all settings looks ok DNS adresses from ISP are present on both WAN settings . When I use inside the router the funktion for DNS it will work but from any client is does not work. When I restart the router alls works fine. After few hours ( it's differnt 1,2 or 6 ) I have the same problem. No entry in the log's !
View 7 Replies
View Related
Feb 12, 2012
We have a managed service provider voip network that requires us to use our own router for the data network. We wanted to use the RV042 for it's easy vpn setup. After installing it worked great for about 10 min. then the WAN port stopped passing traffic. 3 min. later it started working again. We tested the RV042 on a different network and it works fine. We tested an older Pix on the managed network and that works fine. But the RV042 will not work on the managed service provider voip network. The service provider says that on their end it shows our WAN port going up and down.
View 1 Replies
View Related
Dec 20, 2011
I recently took over at a company as IT Manager. All through my career I have heard about the quality of Cisco equipment. Over the past few years I have used a few different Cisco products with good success. When I took over they were using an assortment of old D-link DI-604UP's & DI-804HV routers. The problem is that most of the DSL Internet connections now are faster than the 10 megs that these units WAN connections support. Since they were working fine other than that I felt that replacing them with the RV042 would be a good step. So far I have purchased 6 & implemented 5 of them. The sites vary in number of network devices from 10 to about 50.
The problem is that 4 of the 5 routers start to slow down & finally stop responding after a period of time. If I unplug them, count to 10 & plug them in again they work fine again for a period of time & then quit. The length of time varies between sites & even varies on the same unit. They may go for 2 days or 2 weeks. I never know what I'm going to get. When they go down I don't even have local access to them. It's like they overload & can't accept any more data. I can't tell you what version of firmware they originally had but I can tell you I had upgraded 3 of them to version 4.0.4.02 & then to version 4.1.0.02. I reset & manually re-entered all the settings after I did this.
I have read through the posts & have changed the MTU settings & tried disabling the SPI firewall setting to no avail. The D-link routers ran flawlessley until I replaced them & have done so since I put them back.
I now have over $1000.00 dollars worth of routers that I can't use. I have a boss that is on me because I talked him into spending the money when the $200.00 dollars worth of routers I replaced were working fine.
I have 10 locations to upgrade the total infrastructure in. Routers, switches, etc. If I don't get this resolved quick there is no way in the world I be buying any more Cisco equipment.
View 4 Replies
View Related
Feb 15, 2012
Is there any plan to release an updated firmware for 521w? Or is this done? I currently have .24 firmware but still having lockup issue.
View 9 Replies
View Related
Apr 1, 2012
When my RV042 is accessed for long transmissions (svn check out, usually after 20 minutes ) the client receives a message "Gateway not responding, do you want to wait".
When this happens I see the following in the RV042 system log (the first 3 lines of the log below are normal):
Apr 2 17:36:53 2012Connection AcceptedTCP 192.168.2.2:8888->192.168.1.5:50046 on ppp1Apr 2 17:36:54 2012Connection AcceptedTCP 192.168.2.2:8888->192.168.1.5:50046 on ppp1Apr 2 17:36:54 2012Connection
[Code]....
View 10 Replies
View Related
Aug 12, 2011
We bought an RV042 at the end of June. It is used as a gateway and VPN router. DHCP server is disabled and all IPs are configured manually.Every once in a while (Tuesday night, then Friday night - yesterday, it has hapened once or twice before that) the router appears to restart (see log below) then comes back up with system time of Jan 01 2010. At this point the router will no longer load its configuration page (https://10.29.238.197:16443/) and VPN connection to our customer in Africa drops. However, devices behind the router can be reached and can access the internet. The only way to fix this is to power cycle the router at which point everything starts working flawlessly again.The PID VID is RV042 V03 running firmware v4.0.3.03-tm (May 12 2011 21:27:37). Our RV042 is a newer one with Cisco SMB Router branding not the older Linksys branding.
From the log when the router reboots:
Aug 12 22:38:42 2011VPN Log(g2gips0) #141: retransmitting in response to duplicate packet; already STATE_QUICK_I2Jan 1 01:00:05 2010System Logheart : System is upJan 1 01:00:13 2010System LogWAN connection is up : 10.29.238.197/255.255.255.192 gw 10.29.238.225 on eth1Jan 1 01:00:15 2010VPN Log(g2gips0) #1: [Tunnel Negotiation Info] >>> Initiator Send Main Mode 1st packet
I looked at the log more and all the usual messages assosciated with VPN being established are there - the last thing in the log before the router coming back up again is:
Jan 1 01:03:49 2010VPN Log(g2gips0) #4: [Tunnel Negotiation Info] Quick Mode Phase 2 SA Established, IPSec Tunnel ConnectedJan 1 01:03:49 2010VPN Log(g2gips0) #4: [Tunnel Negotiation Info] Quick Mode Phase 2 SA Established, IPSec Tunnel ConnectedJan 1 01:03:49 2010VPN Log(g2gips0) #4: sent QI2, IPsec SA established {ESP=>0x575a01c0 <0x6534ae4e
So it even claims the tunnel should be up but I can never reach anything on the far side.
View 3 Replies
View Related
Aug 7, 2011
Recently i bought a Cisco RVS4000, upgraded the firmware to latest stable release (Firmware Version: V2.0.2.7) and started configuring it.Yesterday i found out that as the dsl connection drops (i'm using PPPoE with an ethernet ADSL Modem) the product stops logging, both locally and to an external configured syslog (which resides on a linux box over the LAN).
View 3 Replies
View Related
Oct 25, 2011
I am using a RV110W with the latest firmware 1.0.1.6 I have some port forwarding configured, which normally work. But sometimes, all port forwarding stop working. Everything else continues working normally, just all port forwarding don't work any more. I tried disabling the port forwarding and enabling them again, this doesn't work. Also disabling the firewall completely does not work. You have to reboot the router, then everything works fine again. When I make a portscan from outside with a "fresh" started router, the forwarded ports are open. When the error occurs and I make a portscan from outside, all ports that should be open (and have been open before) are closed.
View 8 Replies
View Related