I just bought a dlink 655 from amazon and for some reason the router stops broadcasting on wifi. I cannot connect to it through my laptop or ps3. The only thing that fixes this is removing the plug from the back of it and putting it back in, once i do this, the SSID shows up once again and all is well until the next day (or 2 days after)
View 2 Repliesi have 2 DIR 615 routers which both stop broadcasting SSIDS. Ive had only one connected at a time, thinking it was a bad router, but both behave the same way. Is this a known issue or something ? What happens is, after some time (it varies..sometimes 3hours..sometimes longer), the router stops broadcasting the ssid, and I can no longer connect any of my wireless devices to it. The hardwired connection does work (I have a server connected to it, and it appears to work).The only settings I have changed is my SSID name, and wpa2 password. I've set up one virtual server to port forward requests to the server. Thats it. Nothing complex or anything. And both routers behave the exact same way, meaing they stop broadcasting the SSID.
View 8 Replies View RelatedI bought a DIR-655 (F/W v. 2.00NA) about 6 months ago. It worked well until a couple of weeks ago. Then it started to stop broadcasting WIFI signal without apparent reason. When it did so, I could still connect to it and internet with wired connection, but the WIFI scan does not show my SSID. If I reboot it (either through the admin interface, or just disconnect and reconnect the power), I would be able to reconnect to WIFI, but then WIFI will stop working again in about 8-10 hours. I am rebooting this thing 2-3 times a days and it is very frustrating. Curiously, I borrowed a N300 router to try out
View 10 Replies View RelatedI have two DIR-655s. One is my main router, connected to my modem. The other, on the other side of the house, is set up as an access point. I followed this guide to set up my AP: [URL]
Both are are hard wired. I have both of them using the same SSID. Both are 802.11g only, have the same security mode, and key. The only wireless difference is the channel. One uses 6, while the other uses 11.
On initial setup, everything is fine, but after a few hours, the AP just seems to stop broadcasting a signal. I'm using "Wifi Analyzer" on Android to monitor it. When I look at the AP, the wifi indicator light is still on. If I log into it, change the channel, and press save on the "Wireless Settings" screen, it will broadcast for a few more hours before stopping again. The wired connect of this AP always seems to work (Xbox is hard wired to it).
AP Hardware Version: B1 / Firmware Version: 2.03NA
I the only one who's WRT160N occasionally just stops broadcasting WiFi and have to reset the router to get it back?
View 9 Replies View RelatedThe wireless drops specifically from my laptop constantly at random times. When the wireless drops in order for me to be able to reconnect i have to restart the router itself. There are also random times where the Wi-Fi stops broadcasting altogether. I have a computer connected via Ethernet and it does not lose connection during these times. All the computers are running Windows 7 and the Router is up to date on firmware.
View 5 Replies View RelatedRegion : Argentina
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version :
ISP :
Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : 3.13.12 Build 120405 rel 33996n
ISP : Verizon Fios
(My router says Version 1.9).Had this router about a month. It works fine. Using it in Wireless mode wpa2 security. Get excellent speeds. HOWEVER> It freqently drops connectivity and fails to allow wireless clients to connect at all. (You can see the SSID via wireless clients, but not connect to it). To restore it, I have to disconnect from Power, wait a moment, then reconnect to power. It recycles and connections are working again with no problems (UNTIL NEXT TIME). Seems to happen every few days.
I checked the web site and I appear to have the most current firmware.I have a Trendnet router on different channels in another part of the house which has never had this problem. I disconnected it to test if it was somehow involved, but the TP-Link router had same symptoms when it (trendnet) was not connected. Our Actiontec Router (VERIZON provides this as base connectin to them serving the Cable TV DVRs also) ) has its wireless disabled and is the DHCP server provider to the home network. DHCP is disabled on the TP Link.
Router randomly stops working and sometimes reconnects by it self and sometimes I have to manual reset the router. Also I only get 2-3 bars wireless. Is my router not configured properly or damaged?
View 2 Replies View RelatedI have a linksys WRT54G that has been bugging out a lot. It stops broadcasting the SSID briefly and won't start again until it reboots. Annoying enough problem on it's own, but not my primary concern.My concern now is that when I tried to upgrade the firmware to the latest version (which I presume was causing the problems) the router now is essentiallyunresponsive. The upgrade was successful according to the control panel site, but ever since the required reboot as part of the upgrade process the router hasn't worked properly. 1) The power light blinks constantly rather than staying lit.2) When I plug directly into it sometimes I get access to local networks and other times I don't (limited connectivity). But I never get access to the internet if it's plugged into it as well.3) When I try to go to the control panel site (through the 192.168.1.1) the site wont loadGranted this router is old, but it was working fine other than dropping the broadcast every once in a while. It did need a firmware upgrade, but the upgrade seems to have been a bad choice
View 3 Replies View RelatedMy F5D8231-4 (N1 Wireless Router) keeps shutting down its wireless broadcast. If I reset back to factory settings it comes back on but then I have to setup again.
View 1 Replies View RelatedI just bought the E4200 routher at best buy a few weeks ago. I got it all setup how I want it. Its been working fine then about a day ago it started to stop working at random. All internet just stops working. Wired and Wifi. I have to either wait for it to work again or restart the router.
View 7 Replies View RelatedThis happens intermittantly. This results in most connections (but not all) being dropped. I will be unable to connect to web servers. My connection to videogame servers will drop. However, AIM will stay connected. These were done simultaneously. The same thing happens with my Cisco AE1200 and a D-Link 802.11g adapter I have. Disconnecting my adapter and reconnecting it solves the problem. I have tried doing a factory reset on the router and installing the latest firmware. It seems to happen more frequently when I am doing a lot of throughput (downloading a game on Steam, for instance) but other times it will happen when all I am doing is playing a game (like Tribes Ascend) which uses very little data. This is extremely frustrating. When I pay more than $150 for a piece of networking equipment, I expect it to last more than 3 years.
View 4 Replies View RelatedI have downloaded netflix on our wii. We have a E1000 Linksys router.
While watching anything on Nextflix, the movie stops every 2 minutes and began loading again.
I starting having really bad lag when playing games or just surfing. I put on wireshark and can see my router is broadcasting all the time. here is part of the wireshark log
"1","0.000000000","D-Link_**:**:**","Broadcast","ARP","60","Who has 192.168.0.172? Tell 192.168.0.1"
"2","0.000737000","D-Link_**:**:**","Broadcast","ARP","60","Who has 192.168.0.171? Tell 192.168.0.1"
"3","0.001469000","D-Link_**:**:**","Broadcast","ARP","60","Who has 192.168.0.170? Tell 192.168.0.1"
"4","1.002284000","D-Link_**:**:**","Broadcast","ARP","60","Who has 192.168.0.169? Tell 192.168.0.1"
it does this for the whole subnet then starts over. i turned off all the broadcasting in all the menu and it still doing it. i upgraded to 2.10NA, but it did not seem to do anything to it. I bought this router on 3-5-11. I have not tried resetting it to factory settings. I wanted to see if i missed something first. Router is on a APC UPS with the modem and the switch.
Hardware version is dir-655 B1
firmware is 2.10NA
cox cable is my ISP
I'm using Windows 7 with a TP Link router and an RCA cable modem. I only have a laptop and I had it set up so I had wireless on it, and was able to get wireless on my smartphone as well. All of a sudden the wireless stopped working and now I can only connect to the internet with the router plugged in to my laptop. I just updated my wireless driver and have tried the 192.168.0.1 thing so many times and nothing seems to work. I also exchanged my router for a new one and that worked for about a week and then stopped working again. This happened once before and it didn't work for a couple days and then I woke up one morning and it worked again.
View 14 Replies View RelatedI have a D-Link DIR-652 router, and I can see that it is broadcasting but I cannot connect through my laptop, tablet, or phone. Sometimes it will let me connect but other times it says it is unable to. I can connect when I plug into the router through a cable. I'm doing that now, and I did an ipconfig/all in case to see that:
Windows IP Configuration
Host Name . . . . . . . . . . . . : Kyle-PC
Primary Dns Suffix . . . . . . . :
[Code].....
My internet works fine but after a random period of time, usually 20-30 minutes the internet stops responding. I have ran a diagnostics test using the Intel PROset/wireless tools program and it states on the ping test that there is no response from the default gateway and the DHCP server.
View 3 Replies View RelatedI have a windows vista pc networked to a second pc. I have wirelessly networked internet to 2 laptops. I have an actiontec wireless modem by verizon. All of a sudden my host pc started randomly losing internet connection, but the wireless laptops still have a signal. It seems like the host sometimes can't "see" the modem.Here are my settings while the internet is functioning.Microsoft Windows [Version 6.0.6001]Copyright (c) 2006 Microsoft Corporation. All rights reserved.[CODE]
View 11 Replies View RelatedI have an asa5505 with software version 7.2(3) that randomly stops responding. The firewall sits in front of a public facing webserver that handles a significant amount of traffic.I was wondering that would happen when the asa5505 reaches or exceeds the 4000 connections per second limit... i.e. would this possibly explain why my asa5505 stops responding and requires a power cycle in order to start working again. when it "crashes" it does not respond on either the outside or inside interfaces.
View 5 Replies View RelatedWe have a situation with 20 4410N's They are connected through a 2960 switch. They runned for about a year with no problems. We use the WiFi system with 10 cisco wireless ip phones, several workstations (5-10) and a few mobile devices.
Three weeks ago we took 10-15 iPads in commission (almost equally divided over the AP's), since then the trouble started. Several accesspoints stop randomly responding a few times a, day. We updated to the latest firmware (2.0.4.2), but that did not solve the problems.
Were using 3 SSID's WPA2 encryption and fixed IP's for the AP's. If we can't get a hold on this we have to replace all the AP's by other ones.
I've been using an 802.11 b/g USB wireless network adapter card with my computer to use in conjunction with an AT&T 2Wire router,which is about 20 or 30 feet away off in another room.After about 10 minutes on average, the adapter will stop transferring data suddenly, and it will stay that way for a while. If I do nothing, then sometimes it will start up again after several more minutes, but instead of waiting, I usually will select "Repair" from the Wireless Network Connection pop-up menu, which also works to get it started again. The problem though, naturally, is that after another little while, like about 10 minutes again, it will short out all over again. Sometimes, very rarely, it will stay working for up to maybe an hour, and sometimes, it can short out yet again within a few seconds.
View 9 Replies View RelatedWe have a Cisco 1811 which is running a number of different services. Let me try and explain how everything is working first.
On routed port 0, we have a statically configured fiber connection which routes a public /28. No BGP, etc just default routes. The /28 is divided into a two /29's, once of which is routed to Vlan3.
On routed port 1, we have a PPPoE DSL connection, with a single static IP.
Vlan1 is a 192.168.1.x subnet
Vlan2 is a 192.168.2.x subnet
Vlan3 is a y.y.y.x/29 subnet(the routed subnet)
Vlan1 and Vlan2 PAT the static fiber IP(not the other /29) along with the DSL. The other /29 is used for a few static NAT translations and SSLVPN
There is a zone based firewall in play, as well as a few route-maps to redirect traffic out certain interfaces on the inside.
The problem is, the fiber IP randomly stops responding to ping/ssh, however I can ping the interface IP assigned to Vlan3 from the WAN. DSL never loses connection in this manner.
I can normally reestablish "normal" connectivity by connecting to the DSL and bringing down the fiber and routed vlan in a specific order.
I have noticed a problem recently that our Remote Access VPN will randomly stop working. I will be able to connect and enter my Username+Password and it says Connected, but I cannot ping Remote Resources. If I check VPN Client Statistics, it shows Many Packets Sent/Encrypted, but None Received. It seems this problem affects all devices at once, but leaves the L2L tunnels intact.
It seems to randomly start working for a while, and everything seems fine until it stops working again. I verified that it is not a firewall problem, and it occurs on multiple ISPs and computers.
We also have 2 Static L2L Tunnels, and 1 Dynamic L2L Tunnel all of which operate flawlessly. All sites/remote users use split tunneling.
Below is the config, I just added the keepalives on the RA Tunnel to see if it would work, I haven't noticed any difference yet.
ASA Version 8.0(2)
!
hostname HQ-ASA5505
domain-name xxxxx.local
[Code]....
I am trying to figure out whats wrong with my parents apple airport router. Its connected into an Arris TM402P/110 cable modem. It randomly stops working, the network is there and shows up fine but you cant connect to it. It might work for a day or 2 and then just stops. I am trying to figure out if there is a configuration issue or the airport hardware is just failing. I am not sure where to start troubleshooting. The event log for the modem isnt much help, the following message shows up occasionally:
No Ranging Response received - T3 time-out
Whats interesting is my mom plugged her desktop right into the cable modem and then after plugging it back into the airport the wireless was working again. Is it possible there is a DHCP issue? If the hardware is failing what would be a good replacement for the airport?
I have a DIR-615 Wireless N D-Link router. Simple setup, comcast cable modem ---> router ---> wireless signal to house. For some reason, kinda out of nowhere (can't recall precisely when it began doing this) the router is broadcasting 2 SSID's, one is my configured network, and another network named: D-Link_Wireless. Whats strange thou, is that some devices detect the D-Link_Wireless SSID and others do not. When I go into the router config, all I see is the one configured network, PanzerNet. I wouldn't care so much but I think it's causing some conflictions with my DNS address, making me have to constantly reset my router..
View 14 Replies View RelatedFor the past few months my router has been randomly disconnecting me and everyone who is connected to the router from the internet from anywhere between 10 seconds and 1 min and i can't seem to figure out what has been causing this. It can happen multiple times a day or it can go for a week without happening. it makes playing online games extremely annoying.
Hardware Version: A4
Firmware Version: 1.32NA
I have a D-Link N 300 Gigabit Router. It's only allowing me to download like 30 MB at a time. If I bypass the router, the internet works just fine.How do I fix that?
View 1 Replies View RelatedMy D-Link DIR-655 will no longer let me pull up any web pages after several hours. For example, it works great when first rebooted, but the next morning web pages have timed out. When it is broken, I'm unable to connect to web pages via another wireless access point that i've plugged into the D-Link. I'm unable to use any of the wireless PCs or devices in my house.After it's rebooted, it works well for at least a few hours. It has the latest firmware and has basic, out of the box settings.
View 14 Replies View RelatedI am going to be a Freshman in college next year and I wanted to know if there are ways I could decrease the broadcasting range of the DIR-655 (to keep it as contained to my room as possible).
I plan on disabling SSID broadcast, but would using only 1 or no antennas yield this desired effect of lowered range? Are there features in the router management that can lower the range?
My DIR-655 wireless router randomly quit working. It was plugged into my modem and working great, then it just stopped. I restarted my modem and router, but the "Ethernet" light on my modem does NOT shine when plugged into the router.
I'm sure that the modem is fine, as I have it connected to my PC right now. I also tried it with my friend's wireless router - works fine.
I believe this may be hardware-related. I have tried restoring the router to factory settings and then setting up everything again: No luck.
I haven't had this router for long! Just a little over two years I believe (or it may be just a little over one). I have another wireless router somewhere that's 6-7 years old and still works. If it is hardware related (as in the router just randomly broke), then rest assured I will not be purchasing another D-Link router in the future.
I have a webserver running and have port80 open to recieve requests. Every once in awhile the router randomly disables this port from being forwarded. It is only this port none of the other ports I have open are disabled. I tried switching the server to another port but had the same problem.I have assume its some kind of security feature, since the server gets many requrests that it shuts down the port?
View 1 Replies View RelatedI have been using a TP-Link WR1043-ND for a while now. It is configured as a dumb switch with DHCP disabled. Every other day or so, the device stops taking connections and I cannot access via the IP address. A simple power toggle resets everything immediately. Through this, the LAN connected devices never lose connectivity, I simply am not able to connect wirelessly or access the router via web browser.The only device I connect to the wifi is my phone, so it may actually be more frequently and I do not notice due to my low utilization (and I have 3G so I don't always notice right away if I'm connected). I have a WDTV Live SMP connected to one of the LAN ports and that functions non-stop regardless of the wifi. When the wifi is "down", my phone can see the network and attempts to connect. Sometimes it times out, other times I am repeatedly prompted that the password is incorrect, even though I am POSITIVE that I am entering it correctly. Once I toggle power on the router, the phone connects fine with the stored password.
I have updated to the latest firmware (about a month or so ago): Version: 3.13.12 Build 120405 Rel.33996n My hardware version is: WR1043ND v1 00000000 The router is connected (via LAN port 1) to a wall drop. My upstairs roomate maintains the gig switch and modem, as well as handling the network admin. I simply am using the router as a switch to provide extra ports and broadcast the network over wifi in my apartment.All that said: I need troubleshooting this router and it's configuration before I consider buying a more expensive replacement (and if I go this route, I might add a small switch as well to give me more than 4 LAN ports to work with). I am also considering flashing to DD-WRT before replacing as well to see if that makes a difference in reliability and uptime.
My router is running the stock 1.21 firmware and it has been fine for almost a year before the wireless suddenly stopped working. I reset the router and restored my previous configuration. After the reboot, the SSID is visible and I can connect to it but there is no internet connection. Also the router becomes unresponsive, i.e. timeout trying to access the router configuration page. After trying out different settings it seems that enabling WPA2+AES is the cause.In the mean time, I am running an open wireless network and everything seems fine. Is the hardware faulty? I am reluctant to update the firmware because of a negative experience with another router (same model).
View 2 Replies View Related