Im trying to use my DIR 655 as an access point from my new router, which is a TP-Link TL-R860. I've read about every post and blog I can find about this and still cant get it to work. Currently I have a cable running from the TP main router to LAN port 1 on the 655. I then plugged my computer in to LAN port 2 to configure the router.
View 14 Replies
I changed the router IP of 192.168.1.1 to 192.168.1.2, and disabled the DHCP. But I cannot access the DIR655 at the above new address by a browser. Note that the existing router's IP is 192.168.1.1 which the DIR655 is going to be cascaded with.
View 6 Replies View RelatedUsing dir655 model for access point alone? I want to take the routing part out of this device since it is not needed at this point.
View 3 Replies View RelatedI have just moved into a new apartment that has a free wifi connection the problem is that my apartment is in the basement at the completly opposite side of the office and i cant get a strong enough signal to connect to the internet and im not very good with computers. the first time i tride setting up the repeater i was able to connect everything and get online but it had changed the ssid and when i tride to change it bacck to its origanil name i lost my internet connection and have not been able to get access the internet again.
Tech Support Guy System Info Utility version 1.0.0.2
OS Version: Microsoft Windows XP Professional, Service Pack 3, 32 bit
Processor: AMD Duron(tm) processor, x86 Family 6 Model 8 Stepping 1
Processor Count: 1
RAM: 479 Mb
Graphics Card: S3 Graphics ProSavageDDR (Microsoft Corporation), 32 Mb
Hard Drives: C: Total - 24385 MB, Free - 3678 MB; D: Total - 13776 MB, Free - 13649 MB;
Motherboard: , KM266-8235
Antivirus: None
I've been following those instructions to set a dir-615 as a wifi access point connected to a switch : [URL]. I am now able to connect to the 615 either by wifi or by typing it's ip address with another computer connected to the LAN. Connecting to the 615 by wifi, i can do a ping request to urls or receive and send mail with my e-mail client but i can't access websites using my browser.s it possible to get it working without installing some kind of modified firmware? I tried plugging the Internet ethernet cable in the LAN and Internet ports of the 615, none works.
View 3 Replies View RelatedCurrently have a sbs2003 with 2 nics want to install a wireless access point for the internal network. the wireless router is on the external wan how do i link the access point to this?
View 1 Replies View RelatedI want to set D-Link DIR 655 as Access Point. For your information , I'm using D-Link 2750U (modem + router) as primary wireless router. how do I set D-Link DIR 655 as Access Point ?
View 5 Replies View RelatedI like the ease and price of the 655 as well as the range and speed. I was wondering if you can use them as a bridge to connect another building or just add a second as an access point? It does not seem straightforward from the control panel.
View 14 Replies View RelatedI've moved into a new apartment with a couple of people who already have wifi set up. They are adament about me not running a ethernet cable across the apartment to my room for my xbox 360. I have a DIR-601 from my last apartment, and I am wondering if there is a way to set up the router as an access point that allows me to connect to the existing wifi network and then wire my xbox 360 in.
View 4 Replies View RelatedI just moved into a new appartment and my buddy next door and I are sharing a connexion using a 2wire router (comes with the internet connexion by the company, with their own firmware).
Now, since the 2wire router signal doesn't perform well, I set up my DIR-655 as an Access point.
Now I would like to know what are the optimal settings for a better signal, and also speed. I rather have stability by wifi g/n mixed (maybe will go n only soon).
Some extra questions;
- Should I deactivate the firewall on my DIR655 to gain speed? I imagine it isn't really usefull since there is already another main router.
- Should I check or uncheck "Short GI", "WMM Enable" and "Extra Wireless Protection"?
- Should I activate or deactivate QoS engine and WISH since it is an acess point to gain speed?
- The firmware on the DIR655 is actualy 1.21, is their a newer and stable firmware I should upgrade to?
I have a D-Link DIR-655 with an usb dongle DWA-140. I used to work with a Sitecom WL-341 router.I want to use the Sitecom WL-341 as an acces point to improve my wireless range at the top floors of my house.
What I want to create:
- The modem connects to the D-Link router;
- The D-Link router makes a wireless connection with the Sitecom router;
- The Sitecom router is now an acces point;
- I connect the Sitecom router with a cable or wireless to my desktop PC.
I don't want a cable in my house that connects the D-Link with the Sitecom. If I do this, not only will people get hurt getting up the stairs because of the cable lying there, it also isn't a pretty sight...
I want to use my DIR-615 as an access point. But i dont find the button "activate as access point". This button is shown in this Dlink DIR-300 manual url....Is this for spezial hardware only?
View 1 Replies View RelatedSo, in an attempt to improve my signal in my house I relocated my router upstairs from downstairs by running a long cable to the modem downstairs, since I have read that the signal travels more efficiently down than up apparently. That has not been the case. Now, I have two routers. A D-link DIR-655 and a Netgear router provided by Comcast which is a WNR-1000v2.
possible to set one of these routers up as a wireless access point? Have a router upstairs be the access point, and have a router downstairs connected to the modem. This sounds like this may be a solution but let me know if I'm completely wrong. In my mind, what I'm after is more of a range extender or a repeater but at this point I don't know the difference anymore. It's been quite stressful dealing with my old man for the past week because he can't use his iPad.
I have have my Dir-655 set up as an access point for awhile and would like to change the wireless access code. I can't seem to figure out how to access the setup menu while it is an access point to do this. How I access the router when it is set up as an access point?
View 4 Replies View RelatedI have set up an access point as per the instructions I found on this site. It works perfectly, holds a wireless signal fine. Now, I have the challenge of trying to remote connect to the home computer that is connected to this access point. I have absolutely no clue as to what changes in settings have to be made.
View 4 Replies View RelatedI have a DIR 655 which I am trying to use as a pure access point for a network based on a Comcast SMC Modem/Router On the DIR 655 I have the DHCP turned off and on the Internet Connection I have given the DIR 655 a static address of 10.1.10.2 with Gateway and Primary DNs 10.1.10.1 (The SMC is 10.1.10.1) I have the DIR 655 connect to the SMC Lan to Lan. DIR 655 is G only to deal with and IPAD issue....
The wireless devices get an internet connection BUT... I can only contact the DIR 655 wirelessly the SMC does not show the DIR 655 as connected I can not ping the DIR-655 from the SMC. I can " see" the static addresses I have given to two network cameras but they don't not respond to Port Forwarding I have assigned at the SMC (that is more for info as I realize that might be a SMC issue) . How to make the DLIK visable to the wired network.
I have a DLG-4500 router as my primary router and want to connect a second router (DIR-655) to it as an extention of the LAN to the second floor of my home. I have found instructions on doing this with most other routers, but not DLINK. In fact when doing the initial configuration and trying to disable the WAN link on the second router by using a bogus IP address string (127.0.0.1) The router won't let me save the change? What are the steps for configuring a secondary router cascaded to the primary (both wireless) to extend network coverage.
View 13 Replies View RelatedA friend of mine has a network with the following setup: D-Link DSL-2500U for ADSL, connected straight into a Telkom DG834GUv5 (locally rebadged Netgear) which has 2 PCs connected via cable, and 2 laptops via Wireless. A cable runs from the Telkom into a standard IPLink switch, which merely extends a cable into a D-Link DIR-615 running DD-WRT that has 2 computers connected, and shares wireless to a couple laptops.
At the moment the network is somewhat unstable, and recently the Telkom router has been giving serious problems, even after resetting to default. I want to try make the network a bit simpler and more stable. Firstly, I want to remove the IPLink switch, which merely extends the cable. Is an Ethernet Coupler what I need? Both cables are definitely under 100m combined (probably under 50m).
Now the big thing is a replacement for the Telkom (rebadged NetGear). Should I get another D-Link DIR-615 or is there a better solution? Their budget is between $40 and $60 US. Is it best to stick to the same brand, considering both devices are D-Link at present?
I recently picked up a 655 with hardware version A2 and flashed to the latest firmware. I have a HotBrick router. I only want to use the 655 as an access point AND especially to use the Guest Access or Guest Zone feature to allow visitors to bring their laptops and not virus up my network. My home network is open among a few computers for things like SageTV, file serving, etc.I can get the 655 to function just fine as a standard access point by following the instructions to turn off UPNP, DHCP, etc. as outlined in the manual. I then enable the Guest Access/Zone feature, and of course give it a different SSID name, make sure it's on 24 hours a day, that it is enabled, etc.
But, none of my computers can access the internet via the Guest Account feature, just the regular wireless portion. They show connecting to the Guest Account name, etc. but no internet. I've disabled every security feature I know of to test this. Again, the "regular" WAP tests great, but no Guest Account, which is really important and one of the main reasons I bought the unit.I'm wondering - does the Guest Account feature only work if the 655 is the main router, has DHCP enabled, etc.? Does it have to be the one and only router? If so, I'm in trouble, because I can't really give up my HotBrick due to failover features, etc.
I have connected my DIR-825 to my cable modem through the network ports and completed the configuration. Everything works fine, I am able to connect through wireless to the DIR-825 and access the internet. I had to do this as my cable modem is also wireless and does not allow another router to be connected through the internet connection, but I want to get a better signal stength than the cable modem.When I am not wireless connected, I can see the two bands at full strength in the view available wireless networks screen. As soon as I connect to either the 2.4 channel or the 5 channel, the signal strenth of the channel I'm connected to drops to horrible, while the non-connected one still shows at full strength.i tried disabling one of the channels, but as soon as I connect to the other, that channels signal strength still drops to horrible.
View 1 Replies View RelatedI have a wireless router namely D-LINK 524. i know its a prtty old router..but its never let me down ever before..but thn today i decided to play a couple of games online using the psp/ps3 and well both the devices couldnt read the access point..
Then i go onto my pc and the internet on the pc dont work either :'( so then i reboot the modem nd wifi router..but to no avail.So i unplug da routerand connect da modem directly to the pc and it worked..so i was quite stunned..nd i miss playing online..
So to trim it down the problem basically is my phone/ps3/psp cannot find my access point AND my pc doesnt work when connected through the wireless router.
setting up wifi network in my office. my complete set up right now. the main problem is how to setup my access points . Okay so here it is.
I have 3 - 4 PCS in my office out of which My machine is the main machine and everything is setup on this. so for networking what i have done is i am using a TP link router model TL-WR941D. i had got it configured from an engineer. A cable from my internet modem goes into the blue port of this router(WAN) and my PCs are connected via the LAN port of the router . so everything is working fine right now the local network and internet on all PCS and my laptop also connects through the wifi and is able to access other pcs and also the internet.
To have better signal strength on other floors of the building my engineer had installed 2 access points. They are TP link model Tl-WA901ND. yesterday i updated the firmware of my main router and the settings were some how lost but i managed to set it back to working state using the quick setup utility. so my router and wifi is working fine. But now my access points have stopped sworking . i mean i am not able to get better signal strengths thorugh them. i am assuming theirs ettings /ip etc are lost. now i have no idea how to setup these access points to be used again as part of my wifi network. I looked on the internet but nowhere the thing has been explained in detail. how can i configure my access points/repeaters agaain? i am stuck and engineer is not available for nest few days and my officee internet is suffering.
I wish to turn my TP-Link wireless router into an access point but can't figure out how to do it. I have tried several times but without any success. Below are my information about my main router and the router I want to turn into an access point:
1- Main Router: TP-LINK 3G/4G Wireless N Router 300Mbps - Model No. TL-MR3420. url..
2- Router I wish to turn into an access point:TP-LINK Wireless N Router 150Mbps - Model No. TL-WR740N. url...
My apartment already has internet provided to all of the rooms, but I'm trying to set up my router as a wireless access point. I tried disabling DHCP on the router, but then I wasn't able to get any internet access at all. Does this device not support bridge mode?
View 5 Replies View RelatedI have two DIR-655s. One is my main router, connected to my modem. The other, on the other side of the house, is set up as an access point. I followed this guide to set up my AP: [URL]
Both are are hard wired. I have both of them using the same SSID. Both are 802.11g only, have the same security mode, and key. The only wireless difference is the channel. One uses 6, while the other uses 11.
On initial setup, everything is fine, but after a few hours, the AP just seems to stop broadcasting a signal. I'm using "Wifi Analyzer" on Android to monitor it. When I look at the AP, the wifi indicator light is still on. If I log into it, change the channel, and press save on the "Wireless Settings" screen, it will broadcast for a few more hours before stopping again. The wired connect of this AP always seems to work (Xbox is hard wired to it).
AP Hardware Version: B1 / Firmware Version: 2.03NA
My home network currently has a Linksys router (essentially acting as a wireless access point) in a distant part of the house connected to my main router, a Netgear WNR2000, and this configuration is working fine.
I want to replace the main router with a new D-Link DIR-655 (better parental controls). When I swap in the new router and get the cables plugged in in the same manner as they are in the Netgear router, computers connecting wirelessly to the Linksys router can no longer access the Internet.
The Netgear router is set up with an IP address of 192.168.4.1. The Linksys is 192.168.2.1, and the D-Link is at the default 192.168.0.1.
I just recently picked up a DIR-655 to replace my WRT54GL, hoping that I could get a better stream in my house. The house is 100 years old with plaster and lathe, and I can't relocate the modem and router. So I figured I could use my old WRT54GL as a signal booster/access point on the second level of the house. I read through a couple of guides, and I could get the router to broadcast the signal with full bars, and I could attach to it, but I didn't get any internet. The D-Link is a DIR-655 with firmware 2.10NA. The Linksys is a WRT54GL with Tomato 1.25. Here are a couple screenshots for the DIR-655
View 1 Replies View RelatedSo I've decided to use a different router to resolve some VPN issues, and want to use my DIR-655 as a pure wireless access point. I need the access point to use the same range of IP addresses as the rest of the network (maintain access to networked printers, file shares, etc). However, I can't establish a wireless connection to the access point.
- Defined a IP address for the DIR-655 within the DHCP range of the primary router
- Defined the proper subnet
- Disabled the DHCP server on the DIR-655
- Connect a LAN port of the DIR-655 to a LAN port on a switch (note that it's not connected directly to a router).
When I connect a device WIRED to a LAN port on the DIR-655, everything works fine. The device gets assigned a DHCP address (which I know is being assigned by the main router since the DIR-655 DHCP server is disabled), and I can connect to the LAN and I can access the internet with no problem. So I know the DIR-655 is acting correctly to pass thru traffic. Also, I can access the DIR-655 web configuration page from any LAN device (even a device not directly connected to the DIR-655), so I know the DIR-655 is on that LAN correctly.
But when I try to connect WIRELESS to the DIR-655, it doesn't work at all. Although the wireless NIC is connecting to the DIR-655 (e.g. it asks me for the WPA key), it can't pull an IP address, so there is no connection to the LAN or internet.
my network isn't the most optimal at the moment. Starting from the router, it's a Thomson TG789vn my roommate has set up in his room. The service is DSL. I've connected my laptop to said WLAN from which I connect my access point turned DIR-600 to the internet and share it to my PC and Xbox 360.It works pretty well most of the time with 28 ping to a ~150 miles far server, yet sometimes I lose connection overall, or partly. For example, the Battlefield 3 beta stays connected to the internet while 3 different browsers are unable to load a single page. It seems like ongoing connection are unaffected while new ones don't work. The problem is usually fixed in a few seconds when I disconnect and reconnect the WLAN on my laptop.
View 1 Replies View RelatedI have configured my DIR-605L for no security. I want to provide free wireless internet for the guests that come to my house. How do I insure that guests connecting wirelessly to the 605 can access the internet only and can NOT hack into the computers on my internal house network?
[code]....
So just recently purchased the DIR-825 and DAP-1522. At this point I just want to get the DAP-1522 to work as a wireless access point to my DIR-825. So my wireless laptop would connect wirelessly to the DAP-1522 and the 1522 would go wireless to the router. Pretty basic I guess. I was planning on using the WAP to strengthen the 5 GHz signal to the router but again, at this point, I would be happy to get the 2.4 GHz working.
I've been working on this since last night and got frustrated and went to bed. I woke up fresh and decided to try again and I'm not having making any headway.
DIR-825 is connected to my DSL modem and has no problem accessing the internet. I can connect to either 2.4 or 5.0 directly from my laptop with no problem at all and have access to the internet. Encryption is disabled. It worked with encryption but I turned it off to troubleshoot this AP problem.
It should be simple but I must be doing something wrong. BTW is there a way to scan for network devices from the router or the access point? I tried discovering each device with the wireless setup button on each device but they don't recognize each other so I'm configuring this manually.
So the DAP has access point enabled and 802.11 is running in mixed mode. I've tried different variations but nothing has worked. I've tried 20 mhz and 20-40 auto mhz channels but same problem. Wireless security is off for troubleshooting at the moment.
DHCP server is disabled and I've assigned the DAP an available ip from the router's dhcp range. I can connect to the DAP both wirelessly and hard wired. The problem is that it can't seem to connect to the router. So my laptop can connect to the router and ha internet access. And it can also connect to the DAP but does not have internet access. The ip is showing auto configuration 169.x.x.x when connected to the DAP so I'm not getting an ip. Is the router supposed to assign the ip to my laptop through the DAP? But again, if the DAP can't communicate with the router, then that would explain why I can't get an IP.
As the title might suggest, my network isn't the most optimal at the moment. Starting from the router, it's a Thomson TG789vn my roommate has set up in his room. The service is DSL. I've connected my laptop to said WLAN from which I connect my access point turned DIR-600 to the internet and share it to my PC and Xbox 360.
It works pretty well most of the time with 28 ping to a ~150 miles far server, yet sometimes I lose connection overall, or partly. For example, the Battlefield 3 beta stays connected to the internet while 3 different browsers are unable to load a single page. It seems like ongoing connection are unaffected while new ones don't work. The problem is usually fixed in a few seconds when I disconnect and reconnect the WLAN on my laptop.So yeah, it's not pretty but I have to work with what's available. I'm actually surprised it even works this well. how to optimize the whole thing or how to fix the partial lack of connectivity?
How can I configure my TP-Link router TD-W8950ND act as an access point? I'll be connecting it to a main router which is connected to the ISP.
View 1 Replies View Related
