Cisco Firewall :: CSC SSM 6.0 (Build 1349) Upgrade?
May 22, 2011
I have a old version on my CSC SSM module 6.0, I want to upgrade to the last version.I never use the CSC SSM module, so first i must activate it using the activation key right ?
From my understanding I need to install first the release csc6.1-b1519, i have tryed to find it on cisco software center, but it seems unavaiable. How upgrade my CSC SSM module?At last when I will upgrade the CSC SSM, the activation key remain vaild? (I have also the plus license.)
View 11 Replies
ADVERTISEMENT
Aug 8, 2012
Started a upgrade of my firmware to Ver.2.0.03 (Build 10) for the E1200 H/W v2 and at 98% it stalled this was over wired connection and via http not https.
I'm really disappointed which this router because in all honesty its been one of the slowest I have ever bought whereas the Wireless-N doesn't truly work with N speeds being like 3-9Mbps where if I disable WMM and switch to B/G Only then my speeds jump to 20-30Mbps.
View 2 Replies
View Related
Feb 27, 2013
I'd like to see some REAL LIFE comparisons of ASA firewall throughput (a bit like this one for ISR G2 Routers - [URL].
The reason I ask is that I recently upgraded a firewall from an ASA5505 to an ASA5520 on a small network where the only outside connectivity was a single 10meg Internet circuit with an IPSEC VPN (not landed on the firewall but on a router) to another site.
When I swapped out the firewall the users noticed a big improvement. The firewall is not doing anything out of the ordinary - no IPS or VPN, just standard state full inspection.
View 5 Replies
View Related
May 17, 2011
i have asa 5505 with the asdm v5.2 (4), and the asa v7.2(4). This platform has a base license. if i upgrade adsm and asa on v6.2(1) and v8.2(2) if I lose my license and that you need to activate them? i configured site to site vpn (this firewall and the another) that i lose my configuration if i upgrade my firewall.
View 2 Replies
View Related
Jun 29, 2011
I have two ASA5510's set up in failover, and the secondary keeps crashing after doing the interface checks when bringing failover up. This only happens if I try to upgrade the image on the secondary to anything newer than 8.4.1 (I've tried with 8.4.1-11 and 8.4.2). The primary one run just fine with new images.
I don't have the exact error right now, as I need to do a screen capture from console. It's just a huge crash dump.Are there anything I might have missed during the upgrade? Should I cold-boot both the firewalls in the correct order?
View 7 Replies
View Related
Feb 22, 2012
i have cisco ASA 5510 Firewall using in my network, i have planning to upgrade the Flash memory from 256 mb to 512 mb and the RAM from 256 mb to 1GB.
View 1 Replies
View Related
Jul 9, 2012
I have an old pentium 3 pc that has been given to me and would like to know if it would be possible to utilize as a nas for streaming films photos and music.i am not sure of the exact specs but they are as follows:-pentium 3 celeron 466 mhz processor(coppermine)i was planning on using an external 1 tb hard drive as storage and investing in some extra ram.the board only supports 512 mb of sd ram max.also i am going to have to install a add in usb 2.0 board as only usb is supported natively.
View 3 Replies
View Related
Oct 4, 2012
I am trying to build an IPSec between two 881 routers in my lab. [code]
View 1 Replies
View Related
Apr 13, 2012
I'm wanting to make use of an old PC here that has Windows Server 2008 on it. i basically just want to use it as a backup machine. i have 1 PC, 1 Mac and an iPod Touch that'll be accessing it. what do i need to do to set it up? is there a guide anywhere? how is it different to setting up a NAS using FreeNAS?
View 3 Replies
View Related
Sep 5, 2012
Here is my build that i would like to make and i basically need an adapter that could be compatible. This is my router: Netgear N600 Wireless Dual band router [URL] PCPartPicker part list / Price breakdown by merchant / Benchmarks
CPU: AMD Phenom II X4 965 Black 3.4GHz Quad-Core Processor ($89.99 @ Newegg)
CPU Cooler: Cooler Master Hyper 212 EVO 82.9 CFM Sleeve Bearing CPU Cooler ($32.30 @ NCIX US)
Motherboard: ASRock 970 Extreme3 ATX AM3+ Motherboard ($89.98 @ Newegg)
Memory: Patriot Gamer 2 Series 8GB (2 x 4GB) DDR3-1600 Memory ($33.99 @ Newegg)
Storage: Western Digital Caviar Blue 500GB 3.5" 7200RPM Internal Hard Drive ($62.99 @ SuperBiiz)
Video Card: XFX Radeon HD 6850 1GB Video Card ($137.55 @ Newegg)
Case: Zalman Z9 Plus ATX Mid Tower Case ($44.99 @ Newegg)
Power Supply: OCZ 600W ATX12V / EPS12V Power Supply ($39.25 @ NCIX US)
Optical Drive: Lite-On iHAS124-04 DVD/CD Writer ($14.98 @ Outlet PC)
Mouse: Razer DeathAdder Wired Optical Mouse ($46.48 @ Amazon)
Other: Linux Ubuntu 12.04
Other: Link Depot Model HDMI-2-HDMI 6 ft. HDMI TO HDMI A/V Cable - OEM ($3.00)
Total: $595.50
(Prices include shipping and discounts when available.)
(Generated by PCPartPicker 2012-09-04 21:24 EDT-0400)
View 1 Replies
View Related
May 28, 2012
I am now having trouble to buil a vpn ipsec on an adsl link, my architecture is as follow:
[code]...
whith this output, debbuging seems very difficult. see attached my configuration on router 1841
View 3 Replies
View Related
Jun 10, 2013
I wonder if I can build a NTP Stratum 0 device using a GPS and a Cisco router.Preferred would be a CISCO819 as it has a build in GPS, alternative a CISCO2901 + EHWIC-3G-HSPA+7.
View 1 Replies
View Related
May 2, 2012
Any configuration example to build a vpc b/w 5ks and 7ks? i have total 4 links between them . If not, I am assuming to have the following config for the port-channels:- (Provided the vpc domain is configured).
N5k1 and 2:
int eth1/10-11
channel-group 10 mode active
switchport mode trunk
int po10
switchport mode trunk
switchport trunk allowed vlan a-d
[code]....
So, its basically vpc 10 that has 4 physical links b/w the vpc domain of 7ks and vpc domain of 5ks.
View 3 Replies
View Related
Sep 16, 2012
I recently purchased a build computer. Now I can not connect to the internet. It is not reconigizing the connection.
View 2 Replies
View Related
Feb 28, 2011
have to build a solution for a network of around 150 users from the same building with about 50 users per floor. They are all having an workstation with windows 7 prof (about 75%), windows XP home edition (about 20%) and windows xp prof (5%). They are working in Autocad and I need a server on which I have to put windows 2008 server with AD and will have a role as fileserver.I need to know what are suppose to be the minimum hardware requirements for this server. Having not too much IT experience I need to know if the users that have windoiws xp home edition need to change their OS.
View 3 Replies
View Related
Jun 24, 2011
The wifi connection is all good to go. Now , we have other companies besides us that also managed to tap to the wireless infrastructure, though they don't have the authentication cert, but it is exposed.So, would like to know how can we conta the wireless signal from overflow to another building? Any setting at the WLC that can be tweak? or check the radius to ensure that it didn't overflow?
View 1 Replies
View Related
Aug 3, 2011
I want to build a small demo with the new Cisco Prime NAM 5.1; however, I only have a NM-NAM module for a Cisco Router 2811.I've read the data sheets and I've come across info that the NAM 5.1 software can be installed on the NME-NAM module which is the replacement for the previous one. Nevertheless, it doesnt say that its not supported on the NM-NAM.can I install the NAM 5.1 image on a NM-NAM module? Networkers is coming up and we are deploying a NAM demo!
View 3 Replies
View Related
Dec 26, 2011
I need to build a medium network and connect it to the internet MORE DETALIS; what are the hardware requiremnet i need to build this network?? i need to monitor and control every thing in this network. it should be like this(one ADSL line with high speed connection coming from my ISP-(internet service provider)++ a room to put all the equipment and decives use in the network=routers,modem,servers,cables and so on= ++ then from this room or place i divide the one line coming to sub-netwrks--in my case about 6 subnetworks-- then spread all the cables and so on, to each department or division
View 7 Replies
View Related
Sep 7, 2012
setting up a single home network in my apartment that will be able to connect to and use 2 separate wifi internet connections to provide stability and reliable bandwidth for a home network.
Situation: I have recently moved into an apartment complex that has 2 separate wifi connections that are available to the residents free of charge. (yes i am authorized to use both) I do have the option of paying for and having my own personal DSL line installed but I would much rather use the free wifi and not have the monthly bill.
The Problem: My apartment is located far enough away from each of the routers (One wifi at each end of the building and I am in the middle) that my signal strength is poor most of the time and sometimes heavy traffic on one wifi requires that I disconnect and connect to the other. Wifi A is farther and has very low signal and low or no connectivity. Wifi B has good signal most of the time but gets very slow during peek usage times of the day.
I understand that I need one or more high gain antennas in order to receive adequate signals from either Wifi connection.
Between me and my son we have 2 laptop PCs, 1 Desktop PC, 1 network printer, 1 Xbox, 1 HDTV and my smartphone. I don't want to try to equip each device with its own high gain antenna and try to figure out which device should be connected to which Wifi depending on available signal and bandwidth. Rite now I do not have a Home network set up at all and we are only using 1 laptop and the Xbox and each is directly connected via wifi (usually to Wifi B).
If I could connect to either Wifi A or B with decent bandwidth and reliability and then be able to network or connect all my devices via wireless or wired to my own router/extender etc. I would be happy. However.. Given that I must share bandwidth with the other residents and at times one Wifi has heavy use while the other does not. I have been trying to research how to connect to both wifi signals for load balancing, reliability and hopefully greater bandwidth.
View 2 Replies
View Related
Jun 22, 2008
I have a ASA 5520 upon which I need to build a WebVPN for the company urls - webmail, intranet portals etc. There will be 2 groups -
a. Confidential Access - For senior management.
b. Public Access - For employee access.
RSA Token & LDAP auth would be used for access to the WebVPN. However, I am unclear on certain aspect.How do I isolate the 2 groups? I mean only Senior management should be able to view & access the first set of links while employees see and access the other set of links only.Both the groups will be available to all users loggin on to the WebVPN. Since the authentication mechanism - LDAP - is the same, anyone would be able to access the groups and in turn, urls.
View 2 Replies
View Related
Feb 19, 2012
I have to use 9 Cisco 300 series switches to build a new network. I will use one of them (core switch) in L3 for routing between Vlans (3 Vlans) and the others in L2. Is there a software to centralized all switches configuration, operation and monitoring?
View 1 Replies
View Related
Oct 16, 2012
I have recently gone to upgrade my firewall to version 8.4.4, but afte i upgraded this all the network objects have all got jumpled up, lost there descriptions lost there names and there are some duplicates.
View 1 Replies
View Related
Jul 31, 2012
I just built a new computer that will not connect to the internet, but only while using my wall port, and only this new computer, and only while connected through the router. Totally bizarre, right?I just built a new computer with a fresh install of Windows 7. I set it up directly connected to the router, where I applied all windows updates. I then moved it to where my old computer is, which uses a wall port to connect to the router in another room, where this new computer then fails to connect to the internet or to the router's setup. The new computer's Ethernet LEDs will light up, and the computer will automatically obtain an IP address, but will not connect to the internet or even the router setup.
View 2 Replies
View Related
Sep 27, 2012
I will be building my own computer here in the next month and am looking to become quite informed about building my own wireless network.Trouble is, I'm a bit out of to with what I need and what is good. I'm also officially tired of renting a modem from Comcast (bastards keep bumping my monthly rate up). So what pieces of equipment do I need to build a simple quality wireless network for my home? I would like the network to support two laptops, one desktop, and an Xbox plugged into a LAN line. Also, I'm thinking of using a Rosewill Wirelss Adapter 3 antenna [URL].
View 4 Replies
View Related
Jun 28, 2012
D-Link released firmware version 1.05 build 08, located here: Firmware v1.05b08
View 2 Replies
View Related
Apr 21, 2012
if there is a stable or if the current website offered version of DDWRT is stable and working good on Asus Rt-N66U router?
I really want to work with some of the features like VLAN etc... on this firmware. I am no stranger to the software but I want to be sure I am not going to burn up my router or cause it to frag due to incomplete software
View 15 Replies
View Related
May 1, 2012
I plan to build improved redundancy in to my LAN by stacking two 3750s and teaming pairs of NICs on my Dell PowerEdge servers, with each cable of the pair going to a different switch.In my mind this provides redundancy for the NICs and the switches. Does this configuration will work, and also what type of teaming is supported, as I was planning to have one NIC active and one standby, but can I run this configuration with both NICs in the team as active with load balancing?
View 1 Replies
View Related
Oct 31, 2010
I replaced an ACS certificate that had been installed as follows:
1. Generate CSR file and private key file, then send CSR to GeoTrust (Key length: 2048 and Digest to sign with SHA1)
2. GeoTrust send me a certificate. Issued by "GeoTrust SSL CA".
3. Install the certificate on the ACS. Restart ACS service.
4. ACS Certification authority setup. Issued by "VeriSign Class 2 Public Primary Certification Authority - G3"
5. Edit certificate trust list and select "VeriSign Class 2 Public Primary Certification Authority - G3" as trusted.
6. Enable EAP-TLS, then restarted the ACS service. The problem is when i try to enable EAP i get the error msg:Failed to initialize PEAP or EAP-TLS authentication protocol because CA certificate is not installed. Install the CA certificate using "ACS Certification Authority Setup" page.I searched on cisco and it said to disable the CSA, but in fact there is no CSA installed on this server.
OS: Win 2003 sp2Cisco ACS: Release 4.2(0) Build 124
View 4 Replies
View Related
Feb 28, 2013
when try to build etherchannel trunk in between this unit C4510 with the other C4506 Physically can see that the slot 2 shows red light. I had tried reinsert the line card of slot 2 still show same error below when show log,
after swap current line card at slot 2 with new line card show me need to "try reinserting module" ? What happening on this? If this what we did now is we already assume line card is not an issue, could this be a chassis proble? Hope to get your feedback sooner possible.
%C4K_CHASISS-3-LINECARDSEEPROMREADFAILED : FAILED TO READ module 2's serial eeprom , try reinserting module
#sh module
Chassis Type : WS-C4510R+E
Power consumed by backplane : 40 Watts
Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+------------------+-----------
1 48 10/100/1000BaseT EEE (RJ45) WS-X4748-RJ45-E CAT1644L4UZ
3 48 10/100/1000BaseT EEE (RJ45) WS-X4748-RJ45-E CAT1644L4N8
4 12 10GE SFP+ WS-X4712-SFP+E CAT1645L2X8
5 4 Sup 7-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7-E CAT1645L47F
6 4 Sup 7-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7-E CAT1646L04B
7 12 10GE SFP+ WS-X4712-SFP+E CAT1645L2U4
8 12 10GE SFP+ WS-X4712-SFP+E CAT1645L2VC
View 1 Replies
View Related
Jan 17, 2012
remove beep sound when cpu pre-boot assessment build?
View 3 Replies
View Related
Aug 9, 2012
I'm not being able to wireless distribute the office LAN int-con via recently purchased Tp-link tl-wr740n wireless n router'. Actually, I had no problems with my USR 8054 wireless router before I decided to replace the router with an 'N' one as I experienced some connection loss on my mac book pro(mac osx 10.8) thru USR 8054. The internet connection I have is from a wall socket in my office. I know the hub/router/switch or whatever behind has no DCHP activated because the device connected to that socket cannot get an IP, you must enter it manually together with gateway, DNS etc.. and the values are as
ip 10.50.31.108
subnet 255.0.0.0
gateway 10.50.31.254
Whenever I enter these on my USR's 'static IP configuration' via quick setup and plug the Ethernet cable from the wall socket to the WAN, it works and the router immediately starts to let me surf on the net wireless. However, the same procedure has never succeeded on my Tp-link with its latest original firmware or dd-wrt. It even says no cable connected although it is connect from the wall socket to its WAN.I also tried to connect my computer directly to the wall socket with a regular Ethernet cable and entered the ip, gateway etc manually. It didn't work at first, then I changed IPv6 setting from ''auto'' to ''local connection only'' and I was able connect to the internet with no trouble.
View 1 Replies
View Related
Dec 18, 2011
I am unable to connect both of my smart phones to the access point. I am using WPA2 encryption on the AP. I can connect my phones to other AP's using WPA2. I have other devices that connect to the AP except my Android phones. I would like to be able to get some debug logs except the web interface says that the logging fictions are disabled when in bridge mode. Cisco/Linksys tech support: Any troubleshooting tips other than resetting the access point and or reflashing it.
View 4 Replies
View Related
Jan 7, 2013
I'm looking at the possibility of purchasing a few 3750 to build a switch stack to replace my current core and access switches. I'd like for the stack to support server, SAN, and user traffic, as well as provide simple switch management, redundancy, and failover. I've also been looking at the 4500, 6500, and Nexus series switches (although the Nexus switches maybe a bit too much for my network).
My current environment consists of 3560's as the core/distribution/access switches, a mixture of Hyper-V and VMWare environments (although we're slowly migrating to Hyper-V), an HP SAN (P4500), and about 100 users. Any issues going with the 3750's or have an alternative, more efficient solution?
View 8 Replies
View Related
