USR 8054 Wireless Router - Build A LAN Internet Connection For An Office
Aug 9, 2012
I'm not being able to wireless distribute the office LAN int-con via recently purchased Tp-link tl-wr740n wireless n router'. Actually, I had no problems with my USR 8054 wireless router before I decided to replace the router with an 'N' one as I experienced some connection loss on my mac book pro(mac osx 10.8) thru USR 8054. The internet connection I have is from a wall socket in my office. I know the hub/router/switch or whatever behind has no DCHP activated because the device connected to that socket cannot get an IP, you must enter it manually together with gateway, DNS etc.. and the values are as
ip 10.50.31.108
subnet 255.0.0.0
gateway 10.50.31.254
Whenever I enter these on my USR's 'static IP configuration' via quick setup and plug the Ethernet cable from the wall socket to the WAN, it works and the router immediately starts to let me surf on the net wireless. However, the same procedure has never succeeded on my Tp-link with its latest original firmware or dd-wrt. It even says no cable connected although it is connect from the wall socket to its WAN.I also tried to connect my computer directly to the wall socket with a regular Ethernet cable and entered the ip, gateway etc manually. It didn't work at first, then I changed IPv6 setting from ''auto'' to ''local connection only'' and I was able connect to the internet with no trouble.
I own the linksys wrt160n v2...It has latest firmware 2.03 build 9...After installing this firmware i have noticed the internet speeds have reduced,the router requires frequent reboots to make it stable..
i used to have firmware version 2.02 build 15...It was stable unlike the current firmware...i cant find the old firmware anywhere...how do i revert back to old firmware?
I have a very high speed connection in my dad's office, and it is over 10 mbps. and the connection in my house is worse ( 256 kbps ). So can I use the office connection in home without any problems from the ISP. just like sharing the connection from the office to home.
i just managed to config the Cisco 877 and send it to my client,when the client connect the router from his location the router can't make VPN connection to my HQ office,i can connect to the router using the external IP adress,i tried to reset the VPN tunnel but no avail,
Here is my build that i would like to make and i basically need an adapter that could be compatible. This is my router: Netgear N600 Wireless Dual band router [URL] PCPartPicker part list / Price breakdown by merchant / Benchmarks
CPU: AMD Phenom II X4 965 Black 3.4GHz Quad-Core Processor ($89.99 @ Newegg) CPU Cooler: Cooler Master Hyper 212 EVO 82.9 CFM Sleeve Bearing CPU Cooler ($32.30 @ NCIX US) Motherboard: ASRock 970 Extreme3 ATX AM3+ Motherboard ($89.98 @ Newegg) Memory: Patriot Gamer 2 Series 8GB (2 x 4GB) DDR3-1600 Memory ($33.99 @ Newegg) Storage: Western Digital Caviar Blue 500GB 3.5" 7200RPM Internal Hard Drive ($62.99 @ SuperBiiz) Video Card: XFX Radeon HD 6850 1GB Video Card ($137.55 @ Newegg) Case: Zalman Z9 Plus ATX Mid Tower Case ($44.99 @ Newegg) Power Supply: OCZ 600W ATX12V / EPS12V Power Supply ($39.25 @ NCIX US) Optical Drive: Lite-On iHAS124-04 DVD/CD Writer ($14.98 @ Outlet PC) Mouse: Razer DeathAdder Wired Optical Mouse ($46.48 @ Amazon) Other: Linux Ubuntu 12.04 Other: Link Depot Model HDMI-2-HDMI 6 ft. HDMI TO HDMI A/V Cable - OEM ($3.00) Total: $595.50 (Prices include shipping and discounts when available.) (Generated by PCPartPicker 2012-09-04 21:24 EDT-0400)
We have a WAP2000 that supports a few wireless users in a shop environment. Users authenticate using RADIUS. Users connect without issue and can browse the Internet.
The main local network uses a Cisco 800 router to connect to the Internet via DSL and there is an IPsec VPN tunnel to our main office.
When a user is connected to the network via a wired connection, all systems work as expected. If they are on wireless, they cannot connect to services at the main office. They must make a PPTP VPN connection for applications to function.
The WAP2000 has the latest firmware 2.0.4.0. It has a static IP on the local subnet.
Started a upgrade of my firmware to Ver.2.0.03 (Build 10) for the E1200 H/W v2 and at 98% it stalled this was over wired connection and via http not https.
I'm really disappointed which this router because in all honesty its been one of the slowest I have ever bought whereas the Wireless-N doesn't truly work with N speeds being like 3-9Mbps where if I disable WMM and switch to B/G Only then my speeds jump to 20-30Mbps.
I am unable to connect both of my smart phones to the access point. I am using WPA2 encryption on the AP. I can connect my phones to other AP's using WPA2. I have other devices that connect to the AP except my Android phones. I would like to be able to get some debug logs except the web interface says that the logging fictions are disabled when in bridge mode. Cisco/Linksys tech support: Any troubleshooting tips other than resetting the access point and or reflashing it.
Region : Spain Model : TL-WR842ND Hardware Version : V1 Firmware Version : 3.12.22 ISP :
I am trying to set up a VPN access to the office Windows network by setting the pptp options in the WAN area of the networks settings.
I have entered the public IP address of the office network and also the username and password required by the system. When clicking on the connect button the router attempts to connect but then returns a "disconnected" message.
I need to build a medium network and connect it to the internet MORE DETALIS; what are the hardware requiremnet i need to build this network?? i need to monitor and control every thing in this network. it should be like this(one ADSL line with high speed connection coming from my ISP-(internet service provider)++ a room to put all the equipment and decives use in the network=routers,modem,servers,cables and so on= ++ then from this room or place i divide the one line coming to sub-netwrks--in my case about 6 subnetworks-- then spread all the cables and so on, to each department or division
the only way i can get 300mbps from this router is by having these settings, it seems the only valid settings to get 300mbps from the router are the following:
Network Mode: mixed Channel Width: auto (20mhz or 40mhz) Channel : 1
if i leave the channel to auto it won't show up as 300.on top of that it doesn't want to stay at 300mbps for very long, sometimes its max rate in inSSDer is only 144 or 156mbps. its the weirdest thing, i think this version of the firmware seems to forget to check for how fast its wireless transmit speed is.When it reboots it only transmits at 144 or 156mbps. i have to go in the basic wireless page and just save the settings to reset it to 300, i don't even have to change anything, it resets its max rated speed back up to 300mbps.and more importantly, are the devs aware of this problem for the e1200 v2 ?
1.) If you reboot the modem, it seems to loose UPnP settings. I have to turn UPnP off then back on again in order UPnP to work normally.
2.) Probably petty but when I click the Disconnect button under Router Status, the page doesn't automatically refresh like it did with E4200v1. I have to manually refresh to get the connect button to appear. The refresh issue is also true within the mobile app. Again, not an issue with E4200v1.
I just built a new computer that will not connect to the internet, but only while using my wall port, and only this new computer, and only while connected through the router. Totally bizarre, right?I just built a new computer with a fresh install of Windows 7. I set it up directly connected to the router, where I applied all windows updates. I then moved it to where my old computer is, which uses a wall port to connect to the router in another room, where this new computer then fails to connect to the internet or to the router's setup. The new computer's Ethernet LEDs will light up, and the computer will automatically obtain an IP address, but will not connect to the internet or even the router setup.
I finished building my pc, i booted it up installed windows.Then i installed my drivers of my mobo like i'm supossed to, however my internet wont turn on/detect anything.i am however conected to the internet on my iphone and my laptop, i reinstalled my os/ reinstalled all drivers..
I want to connect to the Internet small office where docsis (internet over tv cable) is used as WAN.For similar tasks but other WANs (adsl, dial-up) I used 800 series. But now I can't find anything in this series to solve my issue. There is 815 but it has no wi-fi.
I can use cable modem that my ISP gave to me: this modem acts as bridge so I can use router with FE-based WAN but it is better to have one device instead of two.
I have 2 older xp pro tough books that connect to my domain via a pair of versa vx 400 access points. automobile technicians use these computers to communicate with cars via a separate wireless card and WiFi device (SPX MVXI) that broadcasts a wireless signal.they always connect just fine to the network but sometimes they drop there connection and don't rejoin which screws up my scheduled tasks (nightly upload). They will reacquire the connection every time if i select it again manually in the windows wireless config.here is what I have done so far
1. set up exclusion range in DHCP distribution on my DC
2. set the laptops up with static IP's within the exclusion range.
3. configured the laptops to auto connect to the network even when its not broadcasting
4. set the access points on channel 7, and the devices on 1 and 11.
I have done a lot of research on this issue, a rep from versa told me that Intel proset wireless isn't very compatible with there product which i this is BS since it does the same with with the netgear WiFi PC cards.
No Network connection after Office 2010 install, I have limmited or no connectivity. I've removed and reloaded drivers, reset router, performed a netsh flush, tried to manually connect, kicked it, threw something at the wall and still no luck.
if there is a stable or if the current website offered version of DDWRT is stable and working good on Asus Rt-N66U router?
I really want to work with some of the features like VLAN etc... on this firmware. I am no stranger to the software but I want to be sure I am not going to burn up my router or cause it to frag due to incomplete software
I am puzzled about some problems that occured at my work place. Unmanaged switch like D-link & Linksys was used and it worked pretty fine only for certain areas of the factory. Then office with more workers will be using managed switch to ensure the workers have decent connection to the local server.
Question is, why are some small offices' connection so ridiculously slow?
*Info*
The switches manage 4PCs
Tested - The main connection cable cannot go through the switch to distribute the connection. Even if there is only 1 PC linked to the switch, it will still be slow. It will be at it's max if it didnt go through the switch, but directly to the PC instead.
True enough that unmanaged switch aren't smart enough to allocate the speed, but why is it possible for some other part of the small office to have fast connection even by using the normal unmanaged switch?
We have a ASA 5505 setup with VPN and using Cisco client 5.0. The VPN works without a problem if we use normal internet access (from home, motel, etc). However if we use a cellular wi-fi hotspot or tether a phone it will connect to the vpn but will not allow us to get on the office network
I lost my network connection after installing Microsoft office 2010.. what can I do to get it back ? I know it is this as i have been fussing with my computer all day.. I created a system restore point just before I installed it.. had network connection.. installed office 2010 and now once I rebooted I dont.. I am running Win 7 enterprise.
My old linksyst wap could see the printer without any special configuration, the new one cannot ,also changing out anther pc with iTunes on it and the two cannot see each other
I have broadband connection on a wired DSL Modem. Now I want to create a wireless networking environment at my home so to work with my laptop and WLAN enabled phone. I do not like to buy a new Wireless router.
Is is possible to deploy my existing modem/router with some extra equipments to build a wifi hotspot?
I want to acccess my office computer from Home PC.I have ZTE DSL Modem + Wireless Router and got new Static IP, so how to configure Static IP From BSNL.
I work for a large company and want reinstall my wireless router so I move from room to room with my laptop without plugging into our network. I have had it set up before but had to spent an hour with tech support to configure the router. Recently I had to reset the password and lost all the settings.
I can get to logged into the set up with the default password but have no idea how to configure it. No matter what I try I get no conectivity when I try to redirect the browser to the internet.
Yeah, I know I should let our network IT staff set it up, but they get all bent when I want to extend my access to a wireless configuration even if it's password protected.
I will be building my own computer here in the next month and am looking to become quite informed about building my own wireless network.Trouble is, I'm a bit out of to with what I need and what is good. I'm also officially tired of renting a modem from Comcast (bastards keep bumping my monthly rate up). So what pieces of equipment do I need to build a simple quality wireless network for my home? I would like the network to support two laptops, one desktop, and an Xbox plugged into a LAN line. Also, I'm thinking of using a Rosewill Wirelss Adapter 3 antenna [URL].
The wifi connection is all good to go. Now , we have other companies besides us that also managed to tap to the wireless infrastructure, though they don't have the authentication cert, but it is exposed.So, would like to know how can we conta the wireless signal from overflow to another building? Any setting at the WLC that can be tweak? or check the radius to ensure that it didn't overflow?
I'd like to use an E2500 as a wireless access point in my network. My computer is connected to the office network through a Netgear 5 port desktop switch. Would it be easier for me to configure the E2500 from the switch? If so, do I just plug it in there and access it via the 192.168.1.1 IP address to set it up? And lastly, what should disable (DHCP) or setup in the router so the internet functions through it?
What are my best options to secure branch office connection to HQ over Provider MPLS cloud. Our existing Setup
<<HeadQuarter>> :: DataCenter hosting Email, ERP, Intranet, Voice Services 10mb link to Service Provider over MPLS CloudMPLS is terminated on a 3825 Router running advance Services
<<BrancOffice>>::Total 10 In Country Branch Offices2mb Link to Service Provider over MPLS CloudTotal users in each branch : 20 MPLS is terminated on a 2811 Router running advance Services
I have just moved into a new office and I have free internet, but I would like to set-up my network multi function printer in the same office.I don't have a router in my office I just have the socket (presumably from the building owners cabinet). Adding another network card.I tried removing the internet cable from my PC and setting up the printer by creating a TCP port but it didn't work. (I used to do this with my HP 1050tn).RouterI tried adding a router but that didn't work either.
i am having problem adding the officejet printer that was uninstalled because it was not working. after three days of online support from HP and Lynksys, I am about to buy a new printer. Can't add printer wirelessly or wired.
