Cisco :: LMS 3.2 Application Registration Fail
Mar 12, 2012
I am attempting to register QPM 4.1.5 into LMS 3.2.1 Portal, under Home Page Admin - Application Registration but It fails.It seems to be a bug where it puts the details in the wrong place when submitting the info.
This is the output that it tries to submit obviously - Description, host name, port number and protocol are mixed up.You have selected the following application to be imported from the remote server. [code]
I'm not sure where to find the Tomcat logs or how much use they would be.
View 1 Replies
ADVERTISEMENT
Jan 27, 2013
I have four rservers. I have found that if the first listed server in my serverfarm is off line, the entire farm quits working. How did I come to this conclusion? You see as part of "serverfarm host PORTAL-FARM" rservers "SISPOAS1 through 4". I can shut down any server except SISPOAS1 and all is well. The load balancer sees the probes have failed to that given server and continuses to load balance to the others. However, If I shut down SISPOAS1, nothing works. I confirmed this by eliminating SISPOAS1 from the configuration completely. After doing so, I could reproduce the exact same problem using SISPOAS2 since it is now the first rserver in the list after I removed SISPOAS1. I'm stumped! Looking at the configuration below, what am I missing???
access-list TRAFFIC line 8 extended permit ip any anyaccess-list TRAFFIC line 16 extended permit icmp any any
probe tcp 389 port 389 interval 2 passdetect interval 2 passdetect count 1 open 1probe tcp 636 port 636 interval 2 passdetect interval 2 passdetect count 1 open 1probe tcp 7777 port 7777 interval 2 passdetect interval 2 passdetect count 1 open 1probe tcp 7778 port 7778 interval 2 passdetect interval 2 passdetect count 1 open 1probe tcp 7780 port 7780 interval 2 passdetect interval 2 passdetect count 1 open 1probe tcp [Code]...
View 4 Replies
View Related
Aug 18, 2011
I am getting sync fail on device manger A3(2.2) to ACE 4710 appliance when I am changing certificate in one of proxy service.
View 1 Replies
View Related
Feb 27, 2012
ACE 4710 software A3(2.7) [code] Why is the fail-on-all option missing from the serverfarm that is of type redirect? This option is something that I would actually need in a certain situation.
View 1 Replies
View Related
Feb 26, 2011
I want to configure my ACE so that if a probe fails, it fails over to the backup rserver, BUT it won't failback to the primary rserver until manual intervention is complete. The problem is we don't want an rserver to fail and failover to secondary, then failback to primary, repeat... (flip-flopping). I want to be able to have time to get on the server and find out what may have caused the probes to fail before it fails back.
View 4 Replies
View Related
Feb 22, 2012
We have two Cisco 2960 TT-L switches. I'd like to reduce single points of failure and have dual servers for most tasks. For example, two firewall servers and two web servers. Should one server fail the other will act as a failover.I'd like to extend the redundancy to the switches, and am thinking of connecting one web server to one switch, and one to the other. In the event a switch failed a set of servers would still run, and be able to talk to each other.I'd like to run two VLANs, one for the LAN, and one of the WAN, and connect the two VLANs on each of the switches with the associated VLAN on the other switch.
View 3 Replies
View Related
Apr 8, 2013
I just bought 2 Cisco3750 X Switches, After I open the box, there are too many numbers lables on the switch.
1. Which number is for product registration ?
2. Can any give me the link for product registration ?
BTW, can explain to me what is PAK, is it come with the switch ? Where I can find it ? I can find serial number but I don't know how to use it and connect with PAK.
View 1 Replies
View Related
Jun 5, 2013
I've just had to rebuild my ACS appliance with new hardrives but I am unable to register the devices to each I get a system error. I thought it may have had something to do with the rebuilt device not being joined tothe domain but it has now been joined albeit using a different ad account, but still cannot register to primary.
View 11 Replies
View Related
Nov 5, 2012
We have a SRP527W, we have created VLAN for DATA and VOICE remotly connected to an office by VPN.
VPN is working fine.
Now we want to register SIP lines integrated in SRP527W to a Cisco Call Manager located in our office.
The problem is that the source of SIP packets is WAN interface of the SRP527W, so packet wont pass in the VPN. Is possible to change the IP source of the SIP registration ? The most useful will be to set the IP source SIP on the voice VLAN.
View 2 Replies
View Related
Mar 5, 2013
We have Cisco WiSM modules on our 6500 switch. I tried to register a 1142 access point to the WiSM. Is there any difference in the way an AP registers and appears on the WiSM as compared to the Wireless Lan controller?
I could see the AP get an ip from dhcp pool ( configured on the switch ) and Ap was visible on the cdp neighbor of switch.
However, i could not locate the new AP on the WiSM module. Do i need to add MAC address to the WiSM as same as WLC.
View 7 Replies
View Related
Oct 11, 2011
I am having issues registering Cisco 3502 APs with a WLC 5508. They initially register and then disassociate with the controller and fail to re-register. Is it possible to telnet to AP and factory rest the AP. I get connection refused when I try
View 1 Replies
View Related
Mar 7, 2012
I'm trying to NAT SIP registration from OUTSIDE interface to Inside interface on ASA
View 1 Replies
View Related
Jul 21, 2012
I ordered controller 2504 and will arrive soon. I want to know that after configure the initial setup of 2504 (i.e. AP manager , Management IPs etc) and defining the DHCP for AP. Will the 1042 lightweight AP will register with the controller automatically or i need to manually define the AP (MAC address) on WLC. and also whether the Option 43 and 60 are correctly defined?
Management Interface: 10.10.22.15
AP Manager Int: 10.10.22.16
ip dhcp pool WLAN103
network 10.10.3.0 255.255.255.0
[code]...
View 4 Replies
View Related
Jun 1, 2013
I'm constantly seeing that the sync and replication status for my secondary admin/monitor node in the primary node as node not reachable. The secondary still thinks it is in standalone mode. When I run the ISE diag tool connectivity tests I am able successfully ping the devices from each other using both hostname and ip and the nslookup also works fine between both nodes. Ping and nslookups also work from different networks within the environment. The two nodes are in the same vlan on a 6500 vss pair but on different switches of the pair.
View 6 Replies
View Related
Dec 9, 2012
i have a problem with 1552E to register with 5508 WLC, and always got "AAA authentication error” in the WLC log, while AAA is not enabled. so my question is , do i need to add the MAC address to the WLC MAC filter list even if i not enable the AAA server in the WLC.
View 9 Replies
View Related
Mar 6, 2011
I just started a project to make a guest wireless network available at every site in my enterprise. Guest wireless networks are currently available at some sites. Two key goals of this project is to enable WPA/WPA2 encryption and to develop a web based registration/autentication solution. All of the sites have a mixture of 1230, 1240, and 1250 autonomous access points. What do I need to do/get in order to make this happen?
View 3 Replies
View Related
Dec 3, 2012
Everytime I make a config change to one of the contexts on our ACE20, I get this message: Config Application in Progress. This command is queued to the system
If I run show download info, I get:
context : context1
Interface Download-status
--------------------------------------------------------------
187 In Progress
199 Pending
Regex download optimization status : Couldn't get status[TNRPC Timed out]
It eventually seems to complete, but it takes a very, very long time. We are running Version A2(3.5) [build 3.0(0)A2(3.5)].
View 2 Replies
View Related
Mar 27, 2013
Report run via Individual Web server URL’sThe report takes less than 20 minutes (average 15 minutes) to fetch and return the data. This is observed 9 out of 10 times.Report run via ACE Load Balanced URLThe report keeps on running for more than 20 minutes and never completes. The front end keeps showing report is running.The data in general when tested directly by running queries against the database (bypassing the platform) completes in 15-18 minutesThe network connectivity for each and every ports involved (Loadbalancer/Servers) have been throulgly checked.
View 6 Replies
View Related
Feb 2, 2012
Cisco 891 configuration Details: [code] I could connect to the Giga bite thernet wan, based on above configuration.When I test on FastEthernet8 for the secondary ISP connection it will not go through the internet.
View 17 Replies
View Related
Nov 27, 2011
I tried to backup ACS 5.1 but i found error messages as below
acs backup25Nov11 repository 25Nov11Repository
% Repository not found
% Error: Invalid repository name 25Nov11Respository
Please use a configured repository.
View 2 Replies
View Related
Feb 19, 2013
I have just started my installation of Prime 1.2. I have the OVA loaded (NCS-APL.1.2.1.12-K9) and I went through all of the setup. I have the webpage loaded but unable to get past the Root login. I then tried to change the password using the "ncs password root password password" command but get the error message "Execution failed: Cannot find user: root". I have seen some people talking about the wrong OVA file but that was for Version 1.1 I think.
View 1 Replies
View Related
May 6, 2013
we installed a new CPI 1.3. Both machines are in the same subnet and close to each other. Everything looks fine and is installed as we see in the config guide.When we halt the VM of the primary Server, the backup takes over but with errors. I'm also not able to login! [code] my colleauges did the same a few days ago also with problems or similar problems and restore the server from backup.
View 2 Replies
View Related
Feb 28, 2013
My client has two ASA-5500 in failover (8.4.4.1).To create AnyConnectVPN, the package must be uploaded on both machines - uncomfortable, but it can be accepted. The REAL problem is that the profiles (.xml file) are not synchronized.When I make a change of any of the parameters, after failover switching I loos alle the change.
View 1 Replies
View Related
Jan 14, 2013
I just set up a new Linksys/Cisco RV082 router with the intent to get VPN working from outside the building. I have gone through the setup and while everything looks good, I have not been able to connect yet. I have tried everything that I know how, and am now hoping to get the answer from some pros.
Here's my setup. We use Comcast Business class internet. The modem is plugged into WAN port 1 on the RV082. I'm using the router as a DHCP server, that is working fine. My local subnet is 192.168.0.0/220
Right now all I want is to be able to log in as a client using QuickVPN. I set up one user and a client to VPN tunnel using the router's config page. Here's the settings I have:
Tunnel Interface is setup on WAN1, checkbox is enabled.
Local Group Setup
Local Security Gatewaytpe: IP Only
Local Security Group Type: Subnet
[Code]....
It seems like something is blocking the connection, but seeing that I have tried this after disabling the firewall completely it doesn't make sense to me. I also went into the config page for the modem and set up the router as a DMZ. I have also tried connecting with the client built into Windows 7, but that doesn't work either, I just get "connection failed with error 619"
I have the port in QuickVPN set to auto, but have tried both 443 and 60443 with same results.
I ran a port scan at [URL] and it shows I have 3 ports open...80,443, and 1723
View 4 Replies
View Related
Mar 18, 2013
We've recently sold and implemented a wireless solution using a WLC, WCS and 1140 APs.
There is a HQ site where the WLC, WCS, DNS and DHCP reside. Active Directory and a RADIUS server are also located there. There is then a WAN link to remote sites which sometimes fails. At the remote sites you'll just have a router, switches and the APs. The intention is for the APs to work in lightweight mode, falling back to H-REAP when the WAN link fails.That works fine, but what doesn't work fine is the APs rejoining once the WAN link is restored.
They just don't. Even days later, the APs are still all disassociated from the controller despite the WAN link being up. I've 'hardcoded' the controller IP into the AP configuration, while the APs initally get the IP for the WLC from DHCP using Option 43. Despite the APs therefore knowing where WLC is, once they're disassociated from it (WAN link failed) they will not reassociate by themselves. Restarting the APs is the only way to get them to rejoin.
With hundreds of APs and in excess of 30 switches, restarting all the APs each time the WAN link fails is pretty ridiculous.
I've logged a TAC case and gone through the whole rigmarole, this is an offical bug and Cisco have informed us that it's due to be fixed sometime early 2011, but besides that there is nothing they can do. So to be perfectly clear, Cisco have sold and shipped a product that doesn't work as advertised and they best they can offer us is a promise to fix it soon. I'm pretty shocked, I've never had this experience with Cisco in the past.
Ok, so now I've got to come up with a decent workaround until we get a firmware release where this is fixed. I'm looking at using CNA to automate the reloading of all the switches, I guess when an outage is reported I'll just write a procedure for the client to follow to reload all their APs.
A script that can query the associated status of APs and reload them as needed, automatically, would be pretty cool. Perhaps that can be done with SNMP.
View 1 Replies
View Related
Apr 3, 2012
I am taking an introduction class to CCNA and we are focusing on the Application Layer,and I'm having some difficulty in understanding what is an Application Layer Service. Is the Application Layer Service the same as Application Layer Software?
View 3 Replies
View Related
Apr 17, 2012
I am running a home configuration where there are 2 PC's each using a different ISP. If one of those ISP's goes down, I would like both PC's to switch over to the working ISP.
View 5 Replies
View Related
Feb 28, 2013
I can't tracert or ping certain websites or servers for games.Before I go on, no I wasn't doing this because of DDoS-ing. I was doing this so that I could find an exact latency number for a gaming server. Now, to continue.What I mean is if I try to ping this server, the session will timeout no matter what the millisecond limit is (using CMD)
Ping: Pinging (IP Host Name) [IP] with 32 bytes of data
Request Timed Out
Request Timed Out
Request Timed Out
Request Timed Out
[code].....
Why does this happen? I am pretty sure this is a security tactic used to stop DDoS-ing, but why does it not matter how long I allow the tracert or ping to run? I really want to understand this so I can understand how people don't get traced as well as don't get DDoS-ed. I didn't put any of the IP's just to keep it anonymous. If you really need the host IP, I will supply it, but I will not supply the tracert IP's.
View 3 Replies
View Related
Mar 4, 2011
fail to connect with net through wifi
View 1 Replies
View Related
Nov 10, 2011
How do you monitor ASA firewall fail over events?
We had a firewall fail over, didn't know it, the configs were out of sync and the customer went down we want to avoid this is the future.
View 10 Replies
View Related
Mar 22, 2012
I have a Question i am testing mobility group with Failover for redundend connection between 2 Cisco 5500 Wlc.On both the controllers i got the mobility working And both the controllers have the same version.And configuration. But when i unplug the main controller the access-Points don't convers to the second one .The just keep on creaming can't find the main controllerAlso with this thus the second wlc need to have the same.Interface ip address like management.
View 8 Replies
View Related
May 23, 2011
I am trying to configure a Cisco ASA 5505 for Remote Clients.I am using ASDM interface and used the startup and ipsec wizards for my configuration but im hitting a stumbling block.For the last 2 days i have tried a number of configuration changes in attempt to make this work but failed, so i have done a factory reset and gone through the wizards again, so i have a clean configuration. Currently i have a Static Public IP Address 81.137.x.x and i am using a Netgear ADSL router, which is forwarding VPN traffic (UDP 500) to 192.168.171.35 (the wan port on the ASA 5505).The Cisco ASA has a default address of 192.168.1.1 I am using Cisco Client 5.0.06.0160.I have configured the client to use Group Authentication with the same credentials as setup through the wizard and im using Transparent Tunneling IPSec over UDP.I have attached 2 documents running_config.txt - which is shows the current ASA configuration Log-View.txt - showing error messages displayed in the real-time log viewer when i try to connect from the remote client.Im not sure whether i need to do any additional configurations for my setup other than simply run the wizards.
View 3 Replies
View Related
Sep 20, 2011
I have an ASA 5520 running, user web trafic, incoming VPN and systems NAT for DMZ services. Nothing new for a standard firewall. I have upgraded the memory in it to 2GB, per Cisco so that I could install and run IOS 8.41. I have uploaded the both the IOS bn image and the ASDM 645 image and set it as the primary boot file. When I reload the ASA, everything boots fine, no errors and all traffic appears to be working fine.But here is my problem:ALL the previously configured VPN sessions will connect to the ASA and show that they are passing traffice (TX and RX increments through the monitor) but if I try to access a device on the other side of the VPN or they try to access services in the corporate network, the connection fails. Ping works, So I know I can reach the devices and the tunnel has been correctly created, but nothing else, . I did not change anything in the configurations for the VPN connectors.But, if I reload the ASA with the 8.21 version image, everything works just as before and all connections are good.
View 3 Replies
View Related
