2 ISPs Second Is A Fail Safe
Apr 17, 2012I am running a home configuration where there are 2 PC's each using a different ISP. If one of those ISP's goes down, I would like both PC's to switch over to the working ISP.
View 5 Replies
ADVERTISEMENT
Cisco Firewall :: ASA5510 Version 8.4 Using 2 ISPs As Fail Over
Aug 9, 2011I have a Cisco ASA 5510 and I am trying to set it up to be able to have it failover to the 2nd ISP connection if the 1st one ever went down. I think I need a nat statement that the "backup" connection will use when the 1st connection goes down, but I am unsure what the nat statement is supposed to be. I have added the commands that I am pretty sure that I need to add for the "backup" ISP connection. Attached are those commands, the interfaces that are set up, and the objects that are set up in the ASA.
View 2 Replies View RelatedCisco WAN :: 2960 Should One Server Fail Other Will Act As Fail Over
Feb 22, 2012We have two Cisco 2960 TT-L switches. I'd like to reduce single points of failure and have dual servers for most tasks. For example, two firewall servers and two web servers. Should one server fail the other will act as a failover.I'd like to extend the redundancy to the switches, and am thinking of connecting one web server to one switch, and one to the other. In the event a switch failed a set of servers would still run, and be able to talk to each other.I'd like to run two VLANs, one for the LAN, and one of the WAN, and connect the two VLANs on each of the switches with the associated VLAN on the other switch.
View 3 Replies View RelatedConnecting Two Different Networks On Different ISPs?
Apr 21, 2012I have a 192.168.1.xxx network connected to Verizon FIOS via Actiontec MOCA / router.I also have a 192.168.15.xxx network connected to Comcast via Motorola VT2442 router (used for Vonage) and a Motorola SB6121 cable modem. Each network has it's own gigabit switch connected to each router. The two networks are physically separated but switches and routers are physically side by side.What is the best configuration to allow devices on 192.168.1.xxx network to communicate with devices on the 192.168.15.xxx network (share printers, NAS, etc), but still have each network served by it's respective ISP, and each device still get it's dhcp, dns, gateway, etc from each respective router?
View 10 Replies View RelatedGet A List Of Tier 1 ISPs?
Feb 12, 2013How I can get a list of Tier 1 ISPs?
View 2 Replies View RelatedTwo ISPs Through One Phone Line?
May 9, 2012Would one phone line be able to support two ISPs? The rest of my family is using an AT&T line and I'm less than amused with it's performance for 4+ people. I have an unused phone jack available but I'm concerned about ordering the installation package only to find that I need a new phone line)
View 4 Replies View RelatedCisco WAN :: 6509 - 2 ISPs From One Network
Nov 26, 2011I have a second link being installed this week to a second ISP. Each ISP has tunnels that terminate on there routers for various services. Right now on the 6509 I have a static default route which sends all traffic to ISP one. Once I get the second link installed I would only like to send specific traffic to ISP1 and everything else to ISP2 unless the link is down. Would policy routing on the 6509 fit my needs?I would like to send 172.20.0.0 / 24 and 10.25.0.0 to isp one and everything else to ISP2.
View 4 Replies View RelatedCisco Firewall :: ASA 5510 With Two Different ISPs
Oct 30, 2011Currently we have a T1 for data connected to a 1721 Router that is connected to an ASA 5510. We would like to add a FIOS line for dedicated online backup. Is it possible to connect the FIOS router to the ASA and route the IP from our backup server to use the FIOS line and everyone else continue to use the T1?
View 3 Replies View RelatedCisco WAN :: Dual ISPs In ASA 5520
Jul 10, 2011We got 2 ISPs -------> two ASA 5520 Primary / secondary --------> LAN . ASA is configured with ACL and Static NAT for our mail , web & ftp servers .
My question is how to configure the 2nd ISP on the ASA to auto switch to the 2nd ISP when the 1st is down with a backup static NAT and backup ACL for the new ISP , in other words how to configure a active static NAT and Backup Static NAT and ACL only for Exchange/Mail Server.Here is the example of our configuration where PIE is Primary ISP & EMC is Backup ISP.
ASA Version 8.2(1)
hostname Corp-ASA
enable password 2KFQnbNIdI.2KYOU encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
[code]....
Cisco :: How Are ISPs Dealing With Growing BGP Table
Nov 11, 2012The problem is the memory available in common BGP-routers. A sup720-3BXL for example, a widly used sup-engine for handling BGP as far as I know, is getting to the limit of its memory size, depending on the number of upstream-providers connected to it.What are you doing, what are major ISPs doing, to circumvent this problem? setting up some server, working as route-reflector, and with a high level of summarizing routes, above supernetting? But at the cost of stability? Or buying new hardware, supporting bigger table? For example the RSP720-3CXL-10GE with up to 4GB memory? But how long will it last? Or a ASR-9001 with 8GB memory or even the ASR9k6 + RSP440 with 12GB mem?
View 19 Replies View RelatedScheduled Load Balancing With Multiple ISPs?
Oct 23, 2011Friend of mine has a setup out in the sticks, currently with two ISPs: Hughesnet satellite, and a line-of-sight WiFi provider; they're also getting a cel tower within range soon and he's looking at adding an HSPA/LTE connection via that as well.the first gives him a static IP and ridiculous speed and bandwidth at night... but far less speed and a painfully low bandwidth cap during the day (you go over, you pay through the nose).
The second gives lots of bandwidth but poor speeds (difficult to even watch a YouTube video) and a constantly-changing dynamic IP.The third, once implemented, will give him good speeds and decent bandwidth (I believe up to 10GB/mo) but again, will get spendy if he goes over that limit.Right now, I've got him set up with both routers plugged into the same network, multi-homed the NICs on his machines (192.168.0.* for Hughes, 192.168.1.* for LOS) and a little script on each computer that will change the default gateway to let him select which ISP he wants to use... however, it's going to get trickier with a third, and will make it even tougher to keep track of the bandwidth used on each one... especially with multiple computers, a DVR, and two users.
So I'm looking for some way to automate all this... something that will, say, use the HSPA feed most of the time for his whole home network, switch to LOS if it gets near the cap, and switch everything over to the satellite automatically during "unlimited" hours. Again, I'm not opposed to setting up something PC-based with the appropriate software, although for my own sanity, it would really need to be Windows-based (I'm way below n00b with Linux).
Cisco WAN :: Configure Multiple ISPs In 3560?
Jul 18, 2011Is it possible to configure multiple ISPs in 3560? and These ISPs traffic should be forward different vlans & different ports. i need configure port wise DHCP also and using different ip addresses please, which device supports this application
View 2 Replies View RelatedCisco WAN :: Dual DHCP ISPs On ASA5505?
Jul 1, 2012I've been searching the net for days now trying to configure the ASA5505 for dual DHCP ISP use. All guides available assume you have one static.
After realizing that it required a Security Plus license to even configure 3 VLANs.
I can choose a backup interface in ASDM. It even says dual ISP enabled. Why cant there be a guide or simple configuration example or am I the only one looking for this kind of solution?
Customer has two ADSL internet connections and want to switch between them if they fail. No load balancing required.
Cisco Firewall :: 5585x - Multiple ISPs Plus WAN And DMZ
Aug 17, 2011Looking to replace an "all-in-one" type firewall (UTM/Firewall, SSL VPN) with a cisco product - the issue i'm running into is that we have multiple ISPs plus WAN and DMZ - overall more than 5 ports on mid-range ASA devices - and from what i read, adding 4-port module precludes me from adding CSC module.
Is there an solution to that other than going for 5585-x model? (kind of over our budget, granted we need 2 for failover)
Cisco Firewall :: ASA 5510 - NAT With 2 ISPs / 2 Different Public IP?
Oct 17, 2011We have an issue with some NAT on an ASA 5510. Here is a simplified drawing of the ASA setup:So the issue is when we try to send traffic from 172.16.3.251 to 1.1.1.1 we got this message in the log:
Oct 18 2011 12:32:12: %ASA-3-305006: portmap translation creation failed for udp src inside
172.16.3.251 /37166 dst outside:1.1.1.1/23
It looks like there is an issue with NAT but maybe is cause of the DUAL ISP setup as packets are routed through the outside interface and not IPtelefoni_outisde?
Cisco WAN :: ASA 5510 - NAT / Default Route To Two ISPs
Nov 14, 2011I am having a strange requirement. actually I am not sure it is strange or not. I am having ASA5510 with 8.4 sw version. Currently one ISP is connected to it. It is working fine. We have some servers that are directly connected to internet using another ISP connection. These servers having public IP addresses configured on their LAN settings. I need to move these servers in to the DMZ zone.
When i connect it to the ASA's DMZ zone,servers will get internet through the first ISP that is already configured on ASA. But i need to NAT the DMZ servers with the IP address provided by the other ISP, which even not configured on ASA.
So what should i do? In short my requirement is
1) need to NAT the server with the IP address provided by another ISP
2) Also note that the default route is configured for the first ISP only in ASA
so Do i need to configure another default route? Do i need to make it with larger AD? So i do it will act as the secondary route only.
I need to make the ASA up and running for two ISP, and servers in the LAN should be able to NAT with the IPs of first ISP and ,the servers in the DMZ zone should be able to NAT with the public IP of the new ISP.
Cisco Routers :: RV082 - WAN DNS Settings When Using Two Different ISPs
Jan 23, 2012Using a RV082 (firmware 2.0.0.19-tm) connected to two different ISPs. LAN IP IS 192.168.1.1. Everything seems to be working OK if I leave the DNS settings for WAN1 and WAN2 set to public DNS servers. If I set each WAN connection to the respective ISP’s DNS settings then I get timeouts when using NS look up. My ISP only accept DNS request from routers on their own network.
Assumption:
I thought that if each WAN is pointing to it’s own DNS server, I should be able to get a reply when I do a NS look up with the server set to this router (192.168.1.1.)
Real life:
The fact is I get a Timeout every time I test a domain name look up.
With the exact same configuration, setting both WANs to public DNS servers, everything works fine
The only reasons for wanting the DNS settings not set to a public DNS server are two. My Spam solution has issues with using a public DNS server was hoping I could increase the speed of DNS look ups using a closer DNS server.My objective is to point the internal DNS server on the SBS 2003 to the RV082 and have the router forward the request as needed to the proper ISPs dns server.
Is my assumption above correct? If I have each WAN configured to it’s own DNS settings I should be able to point to the router for DNS look ups and if the record in not in cache this router will forward it to one of the two WAN’s using that WAN's correct DNS settings?
Cisco WAN :: 6509 - L2 Etherchannel Over 2 ISPs Between Two Sites
Sep 21, 2011We are implementing the network design between the two sites (OLD Data center and NEW Data Center), scheme in attachement.
We have chosen this scheme on the following criteria:
- A single IP network between the sites (for simplicity migration);
- Fault tolerance via different ISPs.
But the problem is L2 etherchannel doesn't work correctly: When one side port is shutting down, on the other side etherchannel will not rebuild and does not see that link down on the other end. We have tried to use LACP in etherchannel (mode active on ports), but result was the same. Is it on the ISPs side?
Should we use this design or we have to subneting the network and make connections between the data centers classically with L3 channels and OSPF?
The configures of Core ports listed below:
OLD data center core (Cat 6509):
interface GigabitEthernet2/6
description #### TO DATA-CENTER core 1#####
switchport
switchport trunk encapsulation dot1q
switchport trunk native vlan 5
switchport mode trunk
logging event link-status
Cisco Firewall :: Dual ISPs On ASA 5505
Dec 5, 2011We have a cisco ASA 5505 with sec bundle plus
We have two ISP's:
ISP1 (Our IP = 30.100.150.50, gateway 30.100.150.8)
ISP2 (Our IP = dynamic, gateway 20.100.150.9) - ADSL
Our internal LAN IP range is 10.9.8.0/24
We want to configure the ASA 5505 to allow users via ISP2 for http traffic We then want to use ISP1 for strictly VPN and access to internal web resources (eg OWA) as we have public IP's there.
Our idea was to configure two gateways on the ASA (e.g. 10.9.8.5 via ISP2 and 10.9.8.6 via ISP1)
Then give the users gateway 10.9.8.5 for web browsing etc Is this configuration possible on the ASA 5505?
Cisco Switching/Routing :: ISR 881-SEC-K9 Vs 891-K9 And 2 ISPs Redundancy
Nov 1, 2012have main office of 70 people.Also I have 2 redundant ISP:One give me 20 mbit/s Other only 2 mbit/s and it is my backup ISP.
I have some resources in data center and I need a IPSec VPN to it and some other location. I suppose there will be up to 3-5 IPSec tunnels. I choose Cisco ISR 881-SEC-K9 with one wan port and 4 LAN switch. But know I’m looking for Cisco 891-K9. There is no security bundle for it. But in cisco.com this router is marked Cisco 891-K9 Security router. Does it support security features like VPNs, ZBF, IOS Firewall, NBAR and IP SLA for ISP redundancy? Also if my boss will choose chipper Cisco router 881-SEC-K9. Will I be able to organize 2 ISP redundancy on 4 LAN switch port inside VLAN interfaces because there is only one WAN port?
PC Health Pack Safe To Use
Feb 26, 2011is PC health pack safe to use
View 1 Replies View RelatedCisco Firewall :: ASA 5510 With Two Outside Interfaces Which Is In Separate ISPs
Jan 5, 2013I have ASA5510 with PLUSE License.I have 2 Inside interfaces as STAFF and MAIL and two Outside interface OUT_STAFF and OUT_MAIL which is in separate ISP's.now i want to nat STAFF to OUT_STAFF and MAIL to OUT_MAILbecause I'm having two default routes it gets impossible to do.
View 1 Replies View RelatedCisco Firewall :: ASA 5520 For Dual Active ISPs
Dec 14, 2011I inherited a network redesign project mid implementation and ran across an issue that I was not 100% sure able to be resolved. Implementation is occurring in which the organization is changing over to a different ISP and we have some customers that will not be able to change their settings over to our new addresses from some time. I have seen a lot of posts about fail over and dual ISP configurations, but I could not relate them to this particular scenario.
View 3 Replies View RelatedCisco WAN :: 2811 Configuration Of BGP For Two ISPs For Link Failover
Nov 1, 2011does cisco 2811 support?if no, can i make it work for BGP?also, i want to know the configuration of bGP for twoo ISPs for link failover.it will be google if u tell me step by step approach for configuring it
View 1 Replies View RelatedCisco WAN :: 2811 - Redundant ISPs Connection On Router
Aug 8, 2012I have two ISP need to connect them on my router.
The Router that I have is 2811 where it contains two Fa ports only, so I put an access switch between the two ISPs and the Fa0/0 then configured the Interface Fa0/0 with two IPs ISP1 and ISP2 as a secondary.
The problem that I faced that when ISP1 become down the another secondary IP (ISP2) stay down and the internal users have no access to the internet.
Cisco WAN :: WAN / Dual ISPs - Can ASA 5505 Do Load Balancing As Well
Jan 24, 2010I want to link ASA 5505 to two ISP's for backup purpsose. I can see this configuration example here url...
Question - does the ASA 5505 do load balancing as well for both connections - is there an example somewhere? (I do not want to buy two ASA 5505's!) which seems the only way I could find configuration details for!
Cisco WAN :: ISPs Layer2 Link But Not VPLS With ASA 6580
Mar 30, 2012I understood that service provider will use hardware Alcatel 6850 on the distribution/core and Zyxel 2108G on customer access level.query is that service provider says it's not VPLS which should work most probably through MPLS network of ISP.ISP noted that it would be direct 802.1q VLAN between two sites without any Layer3 on ISP side.
How to:
- understand what kind of connection this will be?
- is this connection is fine for customer?
- identify if this kind of connection will be fine for converge network (voice+data) ?
- what should I ask to ISP to clarify details?
Cisco Application :: 4710 - Load Balance Two / Three ISPs Using ACE?
Oct 16, 2011How to load balance two/three ISPs using ACE.
What might be the default gateway?Can i create a serverfarm with two rserver with different subnets?
Cisco Firewall :: PIX 515e 2 ISPs Max Speed Is Slower With ISP
Apr 19, 2012have a PIC 515e connected to two ISPs via 2 interfaces. ISP1 is a 3.5Mbps aDSL line, and ISP2 is a 30Mbps business cable. I've confirmed the speeds by connecting the cabled directly into a laptop and using wget to download very large files from known-fast sites.
For admin reasons, I need to access two specific subnets using the slower ISP1. The rest of internet traffic should go to the much faster ISP2.
So I configure ISP2 as the default gateway, static routes for the two subnets to ISP1, set up NAT (PAT) and it all works like a charm. I've confirmed that ISP1 is used for only the two subnets, and ISP2 for everything else. CAPTUREs on the pix also confirm this. So far, it all works great.
But for reasons I don't understand, my max. download speed is 3.5 Mbps (the slow DSL). Using various speed tests and wget, I simply cannot get a download speed faster than my 3.5 Mbps DSL line.
Here is my config:
interface ethernet0 100full
interface ethernet1 100full
interface ethernet2 100full
[Code]....
Internet Only Work In Safe Mode?
May 3, 2012internet only work in safe mode?
View 1 Replies View RelatedInternet Normal Only On Safe-mode?
Sep 8, 2012Logfile of Trend Micro HijackThis v2.0.4
Scan saved at 08:36:37, on 9/9/2012
Platform: Windows 7 SP1 (WinNT 6.00.3505)
MSIE: Internet Explorer v9.00 (9.00.8112.16448)
Boot mode: Normal
Running processes:
C:UsersOrePorAppDataLocalGoogleUpdateGoogleUpdate.exe
C:UsersOrePorAppDataRoamingDropboxinDropbox.exe
C:Program Files (x86)Common FilesJavaJava Updatejusched.exe
C:WindowsSysWOW64RunDll32.exe
C:UsersOrePorAppDataLocalGoogleChromeApplicationchrome.exe
[code]....
Computer Can Only Connect In Safe Mode
Aug 29, 2012My computer came with Mcaffe pre installed on the laptop however did not stop me getting the police e crime unit virus about three weeks ago. To fix this I booted in safe mode and did a system restore to around 3 months before I got the virus. I then installed avast antivirus and did a scan and boot scan which came back with nothing which suggested to me it had gone. This then meant I had both mcaffe and and avast running at the same time. Then until 3 weeks later the internet suddenly stopped working whilst I was on the internet. My laptop sees my router and says it is connected to it but says the router is not connected to the internet. This is false as every other device in the house can connect. However I then tried my computer in safe mode with networking and it can connect to the internet.
View 3 Replies View RelatedInternet Only Works In Safe Mode?
Jan 17, 2011I have uninstalled my norton,turned off my firewall....still only able to access internet in safe mode!
View 8 Replies View Related
