Cisco Routers :: RV082 - WAN DNS Settings When Using Two Different ISPs
Jan 23, 2012
Using a RV082 (firmware 2.0.0.19-tm) connected to two different ISPs. LAN IP IS 192.168.1.1. Everything seems to be working OK if I leave the DNS settings for WAN1 and WAN2 set to public DNS servers. If I set each WAN connection to the respective ISP’s DNS settings then I get timeouts when using NS look up. My ISP only accept DNS request from routers on their own network.
Assumption:
I thought that if each WAN is pointing to it’s own DNS server, I should be able to get a reply when I do a NS look up with the server set to this router (192.168.1.1.)
Real life:
The fact is I get a Timeout every time I test a domain name look up.
With the exact same configuration, setting both WANs to public DNS servers, everything works fine
The only reasons for wanting the DNS settings not set to a public DNS server are two. My Spam solution has issues with using a public DNS server was hoping I could increase the speed of DNS look ups using a closer DNS server.My objective is to point the internal DNS server on the SBS 2003 to the RV082 and have the router forward the request as needed to the proper ISPs dns server.
Is my assumption above correct? If I have each WAN configured to it’s own DNS settings I should be able to point to the router for DNS look ups and if the record in not in cache this router will forward it to one of the two WAN’s using that WAN's correct DNS settings?
View 1 Replies
ADVERTISEMENT
Feb 7, 2012
We have recently purchased an RV082 router for our company. I have successfully managed to establish a VPN connection through PPTP and through Quick VPN (IPSEC?)
When i am connected through PPTP my software SIP client has 0.5% packet loss which is totally acceptable. When i am connected through Quick VPN my software SIP client has a 50-70% packet loss.
i have done the following settings on the router: Bandwidth Management:
High Priority for upstream and downstream UDP 10001-20000 and UDP 5060-5080
Wan Connection settings: MTU: 1492 bytes
I would like to know if there are any other settings that will improve VOIP over Quick VPN since RV082 supports 100 connections compared to 5 for PPTP.
View 2 Replies
View Related
Apr 14, 2012
Lately I encountered random Internet connection issues?My router is a Netgear Wireless ADSL Firewall Modem Router DG834 (Firmware V1.05.0) and my ISP, isn't the most reliable regarding bandwidth... All clients (max 3 at the same time) connect wireless.The problem is that the last few weeks my connections is very unstable, all clients lose the internet connection until you restart the router manually.I can't even connect to the webinterface (192.168.0.1), during the downtimes.
View 4 Replies
View Related
Aug 7, 2012
We're getting the following message in the logs when we ry to connect: encrypted Informational Exchange message is invalid because it is for incomplete ISAKMP SA
One of the router is a V2 and the other is a V4 if that makes any difference.
View 12 Replies
View Related
Jan 29, 2013
We have an RV082 setup with WAN to the internet and LAN IP of 192.168.188.1.If I add a static route like so:
network: 192.168.166.0
mask: 255.255.255.0
gateway: 192.168.188.2
hop count: 1
interface: LAN
The device with IP 192.168.188.2 will be connected directly to one of the LAN ports on the router.Will that work to route, trying to get to 192.168.166.0 to the IP of 192.168.188.2?It just seems odd because the packets would hit the router then go back out through the LAN port.
View 4 Replies
View Related
Nov 17, 2011
isco epc3925 in transparent bridge provided by isp with following wan details
ip=x.x.x.120 subnet=255.255.255.248 gw=x.x.x.121 and 2 dns server ip's
I can't get the one-to-one nat working. read in some forums that the rv082 can do the job.
View 4 Replies
View Related
May 9, 2013
I have a Meraki Firewall that sits behind my Cisco RV082. The Meraki is setup to run a VPN connection with my server but I am having problems passing the VPN traffic through properly.
I have 2 Uverse Internet Connections that the RV082 using load balancing so that they are shared. I have 10 static IP's.
I am trying to come in on one of my static IP addresses throught the Cisco RV082 to the Meraki and after doing a capture on the meraki it appears that it is starting to receive data to intiate the VPN connection but when it sends data back to the VPN client machine it never makes it.
View 1 Replies
View Related
Nov 12, 2012
I have reset my RV082 router (both wit the reset switch and the factory default wizard) and run the setup wizard but regardless I can't connect to shaw.ca which is my service provider. I notice that if I use http://192.168.1.1 the browsers (IE & FF) default to https://192.168.1.1 and then I am prompted for a certificate. I can enter if I ignore the request but after getting in I simply cannot connect to my ISP.
View 4 Replies
View Related
Jan 12, 2012
Is it possbile to NAT to other subnets with the RV082. It is on a 192.168.41.x and I have a phone system on a 192.168.20.x. After searching all over others are saying no.
View 4 Replies
View Related
Jan 14, 2013
I just set up a new Linksys/Cisco RV082 router with the intent to get VPN working from outside the building. I have gone through the setup and while everything looks good, I have not been able to connect yet. I have tried everything that I know how, and am now hoping to get the answer from some pros.
Here's my setup. We use Comcast Business class internet. The modem is plugged into WAN port 1 on the RV082. I'm using the router as a DHCP server, that is working fine. My local subnet is 192.168.0.0/220
Right now all I want is to be able to log in as a client using QuickVPN. I set up one user and a client to VPN tunnel using the router's config page. Here's the settings I have:
Tunnel Interface is setup on WAN1, checkbox is enabled.
Local Group Setup
Local Security Gatewaytpe: IP Only
Local Security Group Type: Subnet
[Code]....
It seems like something is blocking the connection, but seeing that I have tried this after disabling the firewall completely it doesn't make sense to me. I also went into the config page for the modem and set up the router as a DMZ. I have also tried connecting with the client built into Windows 7, but that doesn't work either, I just get "connection failed with error 619"
I have the port in QuickVPN set to auto, but have tried both 443 and 60443 with same results.
I ran a port scan at [URL] and it shows I have 3 ports open...80,443, and 1723
View 4 Replies
View Related
Jan 24, 2012
I have a VPN tunnel from one RV082 to another, first router has IP range of 192.168.1.0 and the second one has range of 18.18.18.0, the connection works fine, here is where the issue starts, I am at a PC in the 18.18.18.0 network and I ping an IP in the other one e.g. 192.168.1.50 and it pings fine, but when I try to RDP into it or do anything to it I get no response, is it a firewall issue? Is it a NAT issue? I am at a loss, now that IP i mentioned does have RDP enabled and working because it is being port fowarded in the 192.168.1.0 router and I can access it through the public IP.
Also a workstation with a static IP 192.168.1.18 I can ping it if im in the local network but if I am in the remote one I cannot at all.
View 7 Replies
View Related
Jul 28, 2010
we have an RV082 router that a few days ago started restarting itself after normal usage.The simpton is that when people come to office, starting using the Internet the RV082 resets. It stays online for 3 to 12 minutes and then it resets again.
clicking on Reset to Factory Default in the web interfaceafter the reset, I confirmed that it was reset to factory default I reset it again using the reset buttomre-configure the RV082 manually.I also tested with another identical rv082 (hw version and firmware version) and after doing a backup of the config of the original rv082 and restoring it in the new rv082, the same problem happends.
View 20 Replies
View Related
Mar 15, 2013
I have an RV082 10/100 8-Port VPN Router and have configured the NAT table to allow for remote users, however I've run into an issue. It seems like there is a limited number of entries that you can put in the table,10, and I need to configure about 5 more IPs. Any way to expand the NAT table, or alternatively recommend a different router. I would also be willing to add another router to the network, but I have little experience doing that.
View 3 Replies
View Related
Jul 18, 2012
Are the RV042 and RV082 routers SIP AWARE?I haven't had any luck finding documentation stating such.
View 2 Replies
View Related
Oct 20, 2011
Just purchased a RV082 and once I switched a bunch of users over to it I can no longer access the web admin section. I have tried using both IE and Firefox and have used multiple workstations. I get to the login screen but it doesn't get any further. I am running the latest firmware v4.0.4.2-tm. It works for a while then just stops. The only fix is to turn off the device and back on and then it starts working again.
I've seen this issue on other small business cisco devices and had to stop using this because of this issue and switch to a higher grade cisco product but was hoping that this particular issue would have been resolved now across cisco's products.
View 7 Replies
View Related
Jan 9, 2012
I just migrated our office network router to a RV082. While configuring it, I came across three problems:
(1) From our ISP we have four public IP addresses which I want to make use of for outbound traffic. With the previous router we used we could configure LAN IPs(ranges) to map to static public IPs. Does RV082 support this? I could not find an option for that at the web-interface. From what I understand the 1-1 NATing only goes both incoming and outgoign ways and actually is 1-1 and not the many-to-one I am looking for.
(2) How is it possible to configure incoming port forwards to use a specific WAN interface? Will it always be the primary WAN interface?
(3) Does the telnet access provide more configuration options? I could not log in to it with the same user credentials as with the web-interface.
Serial Number : NKS1532xxxxFirmware Version : v4.0.4.02-tm (Jul 4 2011 13:30:56)PID VID : RV082 V03Firmware MD5 Checksum : 1f84d8d0a2a8b99f9bfa4409e64547aaLANWorking Mode : Gateway
View 0 Replies
View Related
Apr 27, 2013
we have a RV082 and have the DMZ option enable for a range of IPs within the same subnet of WAN IP and this works great. I have another range of Public IPs from our ISP that is not in the same subnet of the WAN IP and do not see a way on the RV082 to include this 2nd bank of Public IPs in the DMZ. Our ISP internet feed plugs into the RV082 WAN port and we have a switch pulgged into the DMZ port of the RV082 that is used to connect the public devices in the current DMZ. Both banks of Public IPs from our ISP come over via the ISP internet feed plugged into the WAN Port. My question is, if I cannot configure a DMZ rule to allow this 2nd range of Public IPs to "travel" to the RV082 DMZ port.
View 0 Replies
View Related
Nov 12, 2012
I would like to set the subnet mask off the lan to 255.255.240.0 but the selection menu do not allow to do it.
View 8 Replies
View Related
Sep 25, 2012
I wanted to know if you can connect a Cable modem to a SA520W, then connect a RV082 to the SA520W?
View 5 Replies
View Related
Mar 24, 2013
We recently moved our network over to RV082 router and its working great, well now we want to take advantage of VPN for our sales staff.
I was able to setup the VPN and using a PC at a remote office I can launch the quick connect and it connects right away, RV0 even shows the user connected. However the user cannot ping anything on our network via name or IP, connect to any resources, etc...
My understanding was when the client VPN would connect the user would get an IP from DHCP (this is on our Server 2008 DC) and they would be using that address, but when I run IPCONFIG on the client PC they just have there standard IP from remote office.
View 8 Replies
View Related
Feb 10, 2013
I'm planning to buy a few Cisco RV082's for remote offices and using them to connect to main office Cisco 2851 site to site vpn. So I guess, simple site to site vpn will work without much problem, but I wonder, will backup vpn feature work as expected on backup WAN channel and how should I configure it on the IOS side?
View 1 Replies
View Related
Jan 19, 2010
The RV082 is a great unit, however when VPN clients connect the QuickVPN Client has a setting to use the Remote DNS settings of the RV082. The RV082 has no way of linking or using a user-defined DNS. I have an internal DNS Server that I would like the VPN Clients to query on internal name lookups (kindof the point of having client vpn, so they can access internal network shares etc. On the diagnostic page the ping and name resolution can only check external DNS and internal IP's. Wouldn't it make sense to at least make the RV082 aware of internal DNS Servers? Then the Ping and DNS lookup would be able to test both zones? Is this something that can be looked at by Linksys Developers for this product? The WRV210 (a cheaper and lower level model) has this functionality.
View 8 Replies
View Related
Aug 29, 2012
Experiencing a strange issue with v3 hardware. After a short period of time, I cannot log into the web administration - either locally through standard port or remote through non-standard port get login prompt, enter correct username & password, page refreshes with blank background and first page (status?) never shows.power cycling the router restores access to the web administration page, for an uncertain period of time before it barfs again.
I was running older firmware, updated to newest 4.2.1.02 (?) and same problem. Only thing that is better is the internet didn't completely lock up when I tried to access the administration page, like it did on the older firmware.
View 4 Replies
View Related
Dec 1, 2010
I have an RV082 for use in our office. I wanted to create a public acess point on a different subnet/vlan and so configured port 8 of the RV08 as VLAN2. When I plug a laptop into this port it immediataley gets an IP address from the DHCP server on VLAN1 and can communicate with the rest of the network.I thought the whole point of the VLAN option was that this shouldn't happen - what I've incorrectly configured?
View 17 Replies
View Related
Jul 13, 2012
I have an old RV082 that I suppose has failed. The red diag light on the front panel is lit and nothing works. I've already replaced the unit, so I don't really need to fix it. Here's my issue: the setup on the old unit was pretty complex with a number of port forwards and other non-default settings. I'd like to recreate those items on my new router, but they were never written down so I don't know what they were. I've tried to connect a computer to one of the LAN ports, but they're all dead. Is there any way to get at the configuration page?
View 2 Replies
View Related
Jan 27, 2010
Is there any IPv6 support planned or in the works for RV082?
View 3 Replies
View Related
Aug 12, 2012
I am setting up a SBS 2011 Essentials sever using a rv082 router. I have a decent understanding of how everything is suppose to work, but execution has been sloppy. My aim is to set up a central storage location, back up services, remote access and VPN. Yesterday I had set up dhcp and dns roles on the sever, configed port forwarding and firewall setting on the router, at that point I was just bouncing around everywhere trying to get stuff to work, clearly not the best way I know. Before I left I reinstalled sbs for a couple of reason, along with resetting the router to default.
View 1 Replies
View Related
Nov 14, 2012
i purchases cisco rv 082. i set MTU vale at 1500.i use public IP for WAN and just using one WAN.
View 4 Replies
View Related
Feb 13, 2012
I'm trying to setup a VPN between an RV042 V3 and an RV082 V2 router. They get connected but no traffic gets through the tunnel. I tried with and without firewall,DPD, Keepalive, forward secrecy but nothing worked. What should I do? I don't want to throw out the V2 routers. V3 to V3 connects fine.
View 1 Replies
View Related
Sep 8, 2011
I did install server system with mscs and Domain controller and Active directory.I want to connect this dc/ac server from other places such as korea / and japan.
I have a public IP But our country ISP Don't open 135/445 port for security. So I can't connect DC/AC server from other places.At this time i did read many article and find good way to handle it. Is it possible for other servers to connect DC/AC server by using the RV082 VPN service.
View 1 Replies
View Related
Nov 29, 2009
I've been having trouble with the internet connection speed on my Mac. I originally noticed the problem when my mail kept timing out whenever I sent an attachment, I went to different forums trying to find the solution but nothing really worked, so I found work arounds for the email and lived with it. Recently the company I work for moved offices and I was no longer behind the RV082 and my internet ran better dispite the slower connection. Once we finished moving, I needed to use the Dual Wan Load Balance feature of th RV082 so I set it up in the new office and my internet was slow again. Unfortunatly in the new office there are several more Macs than just mine so I really need to get it working. Currently we have 2 seperate networks for PC and Mac and I really need to get them on 1. Is there a setting I may have overlooked or is it not going to work with Mac.
View 26 Replies
View Related
May 1, 2012
I have the Cisco RV082 with firmware v4.0.4.02 Comcast is connected to Wan 1 and works perfectly.I've enabled load balancing and am trying to get verizon DSL to function on wan 2.My verizon DSL line is connected via their provided actiontec GT784WNV router. I've enabled transparent bridging on the actiontec router and have PPPOE set up in Wan 2 on the RV082.
Wan 2 shows the following information, but will not connect to anything.
IP Address : 108.34.xx.xx
Default Gateway : 10.4.53.1
DNS : 71.242.0.12
Dynamic DNS : Disabled
I'm able to ping and traceroute most sites.
View 2 Replies
View Related
Feb 27, 2012
I've a problem with Cisco RV082. I want to connect to my public IP from local IP. But it seems it's been block by the firewall.I've added a firewall rules to allow ANY connection from LAN to outside world. But has no effect.
LAN IP : 192.168.1.5.Public IP (which is assigned to LAN IP 192.168.1.5 by One-to-One NAT) : 118.xxx.xxx.xxx
View 6 Replies
View Related
