Cisco Routers :: Slow Internet On Mac Using RV082?
Nov 29, 2009
I've been having trouble with the internet connection speed on my Mac. I originally noticed the problem when my mail kept timing out whenever I sent an attachment, I went to different forums trying to find the solution but nothing really worked, so I found work arounds for the email and lived with it. Recently the company I work for moved offices and I was no longer behind the RV082 and my internet ran better dispite the slower connection. Once we finished moving, I needed to use the Dual Wan Load Balance feature of th RV082 so I set it up in the new office and my internet was slow again. Unfortunatly in the new office there are several more Macs than just mine so I really need to get it working. Currently we have 2 seperate networks for PC and Mac and I really need to get them on 1. Is there a setting I may have overlooked or is it not going to work with Mac.
View 26 Replies
ADVERTISEMENT
Feb 18, 2013
I have an RV042 VPN tunnel with an RV082.The RV042 has a public IP Address obtained by PPPoE, the RV082 has a public IP Address obtained via Static IP.The problem I see is a really slow performance. Both internet conections are idle and the performance is about 2 or 3 kbyte/s My question are if I should I enable any of this:
- Agresive mode
- NAT Traversal
- IP Compresion
- Dead Pear Detection
How can I troubleshot this slow performance?
View 2 Replies
View Related
Nov 14, 2012
I'm owner of Cisco RV082 router and I have a problem with firewall setup.I would like to deny internet access on port 80 (all sites) for group of users, and allow them internet access for one site by HTTPS (443)After applying rules internet connection is really slow.. Users have to wait something like a 30 sec for a website..I descovered that the reason for slow internet connection is DENY rule. After disbling DENY rule everything works fine..Now I have a few rules added to firewall:
Priority:1 Action: Deny Service: HTTP(80) Source interface: LAN Source:10.82.0.51-10.82.0.245 Destination: Any
Priority:2 Action: Allow Service: HTTPS(443) Source interface: LAN Source: 10.82.0.51-10.82.0.245 Destination: 80.64.59.42
What's wrong with those firewall settings?
View 1 Replies
View Related
Jul 17, 2012
I have a network of 50+ users with half running XP and half running Windows 7. Soon we will be upgrading all users to Windows 7. During the past month a number of the Windows 7 users have reported intermittent Internet connectivity. I would go to their computer and see that they are getting all the correct IP information from the DHCP server and reboot their network adapter. Usually one reset of the adapter would do, but sometimes had to reset it twice or three times before connectivity would occur.
After a few weeks of this more users would report consistent intermittent connectivity. Just to the Internet, as they were able to reach their folders on our file server and were able to receive e-mails from our e-mail server. I decided to monitor the network traffic on one of the adapters having the issue using Wireshark, and found an ARP request and reply for the gateway IP. I logged into the router and found that the reply given to the Windows 7 machine was incorrect, as the MAC address given to the Windows 7 machine was the WAN1 port of the RV082. The LAN port on the router is 192.168.0.1 and has a MAC of xx-xx-xx-xx-xx-x0. The WAN1 port on the router has a public IP and has a MAC of xx-xx-xx-xx-xx-x1. I checked the arp cache on the Windows 7 computers and confirmed that when they have no internet connectivity the ARP cache reads like this: 192.168.0.1 xx-xx-xx-xx-xx-x1 dynamic
The machine is able to ping every machine on the internal network except for the gateway IP. Also, after updating the cache to map the gateway IP with the LAN port MAC address, using: netsh interface ipv4 add neighbors "connection name" 192.168.0.1 xx-xx-xx-xx-xx-x0
the issue was resolved for that Windows 7 machine. However, the issue is ongoing for every Windows 7/Vista machine added to the network. I do not want to update the ARP cache on every Vista/7 machine introduced to the network.We are running firmware 2.0.2.01-tm which was updated from 2.0.0.19-tm just 2 weeks ago.
View 3 Replies
View Related
Feb 24, 2013
We have offices in USA and Venezuela.In our USA office we have a RV042 router and in Venezuela we have a RV082 router.We have connected a VPN tunnel (gateway-to-gateway) between both offices.
The point is:How could we redirect the internet traffic from our Venezuela office (RV082) to the USA Office (RV042) to navigate using USA public IP's?
The reason for this is that we need to use online streaming services which are only available for IP's from USA and we can't use them from the Venezuelan IP's.
We can not use the PPTP option since the equipment which will use the streaming services (like hulu, crackle, etc.) in Venezuela is a Google TV device which doesn't allow the configuration of proxy navegation or PPTP VPN connections itself. That's the reason why we need to do that through the routers.
View 1 Replies
View Related
Nov 16, 2010
Material in question:
Router Model: RV082
Firmware: 2.0.0.19-tm
Only primary WAN port used
Description of problem:I've had a 50mbps internet line with a 2mbps upload for a couple of weeks. I thought my ISP was having trouble because I was only getting 30mbps down and 700kbps upload with noticeable packet loss, however after connecting a laptop directly to the modem after office hours, I realized that I can reach 53mbps down and almost 2.5mbps up. But when I connect directly into the router I only reached the much slower speeds mentioned above previously. (40-60% slowdown)All transfers over LAN reach their full 100mbps transfer speed. So it seems to just be a problems with the WAN.My next move is to back up the router, flash it and then try it with basic default configurations to see if a setting is causing the slowdown.On the other hand, it just occurred to me that perhaps the router was not designed for such a fast line. Does the RV082 can handle a 50mbps internet connection? How to successfully deployed such a fast internet line with this router?
View 6 Replies
View Related
Jan 24, 2012
Recently I placed an Cisco SRP 526W, but this modem is acting quite strange. I have configured an ADSL connection, some NAT forwardings and a VPN tunnel, all of this is working fine. When the Cisco is booted and running, everything runs smooth. Internet is working nice, I can connect over the VPN tunnel to the internal network and so on. The problem is that after a while, mostly after a day or two days, internet browsing is showing problems. IE can't display the page and I have to refresh 1 on 2 times to reach te webpage. I can't connect over the VPN tunnel to the internal network or the internal ip-address of the router, the router is not responding on ping request on the internal ip and external ip. The NAT forwardings are still responing though.
After a reboot everything is running fine again, but I can't let my customer reboot his router each day.
From the ZyXEL modem/routers we used to place at our customers I know the NAT table runs full and I had to use a greater value
View 6 Replies
View Related
Aug 2, 2012
The other day I decided to upgrade my old 10/2Mbps connection to a 100/5Mbps cable connection and my ISP gave me the EPC3825 router. When using an ethernet cable everything works great and my speedchecks max out every time, the problem is that I can't have cables all over my apartment so I'd like to use wireless. With a computer located right next to the router I've gotten as high as 20Mbps and usually I'm left at about 3Mbps. I'm aware that using wireless can result in a small drop of speed but this just seems too much, especially considering the fact that I ran a steady 10Mbps when using wireless on my old connection.
Model:Cisco EPC3825
Vendor:Cisco
Hardware Revision:1.0
Bootloader Revision:2.3.0_R3
Current Software Revision:EPC3825-v302r125532-110504c
Firmware Name:epc3825-v302r125532-110504c.bin
Firmware Build Time:May 4 14:04:04 2011
View 1 Replies
View Related
Jan 31, 2012
After upgrading the firmware on my RV042 router to version 1.3.13.02-tm, I am experiencing very slow Internet response on most sites. In some instances, when the page does load, it lacks many graphics. Frequently, I also receive a "server not found"error. In all cases, reloading the page (once it has loaded) results in a complete page display. This is occuring on two MacBook Pros and also on an iPad. The router is a version 1, so no further upgrades are available. I contacted support, but since it is out of warranty, they are unwilling to assist. Prior to the upgrade, everything worked fine, as it has for 5 years.
View 1 Replies
View Related
Nov 4, 2011
We are having several issues with the new batch of RV016 (rebranded as cisco and with cisco firmware. The Cisco RV016’s are configured to load balance aDSL internet access from 4 Cisco 877 modems/routers. Ports used are WAN1, WAN2, WAN3, WAN4.
Issues are: WAN 1 port resets to 0.0.0.0 regularly and traffic on WAN 1 fails DNS fails regularly behind the RV016 onlyIntermittent internet connection behind the RV016Slow internet connection behind the RV016Extremely slow DNS query and reply behind the RV016 (DNS resolve takes 1min -1m30)
The issues above are reported from different deployment sites and with different scenarios.
We also test above with Code...
View 1 Replies
View Related
Nov 17, 2012
My ISP tested my connection and told me my signal is very weak. I can no longer play games online because I lag tremendously. I can't steam videos while someone else is using the internet either. Also I can't access it on wireless devices unless I am in view of the router. I'm not sure what caused my connection to suck butI have the essential plan from cox.com. When I test my connection on speedtest.com I average 75ms/ping, 3.25mbps/dwnld spd, and
View 2 Replies
View Related
Feb 10, 2013
Belkin N300 - bought two weeks ago and have had very slow internet connection since.
View 1 Replies
View Related
Feb 13, 2013
Having an issue with my Belkin N600 router - when initially installed it was working fine but in the past week it has gtten slower - if I connect directly to my DSL modem my speed is 1.5 MBS when I use the router connection my speed drops to .1 MBS - tried resetting to factory defaults & that did not work also tried resetting my modem *& router still having the same issue.
View 9 Replies
View Related
Aug 7, 2012
We're getting the following message in the logs when we ry to connect: encrypted Informational Exchange message is invalid because it is for incomplete ISAKMP SA
One of the router is a V2 and the other is a V4 if that makes any difference.
View 12 Replies
View Related
Dec 15, 2012
Ever since I upgraded my PC to Windows 8 the internet has been SLOW... It works fine still on my tablets and PS3. Looking online they seem to say I need new drivers? Not sure what to do.
View 2 Replies
View Related
Jan 29, 2013
We have an RV082 setup with WAN to the internet and LAN IP of 192.168.188.1.If I add a static route like so:
network: 192.168.166.0
mask: 255.255.255.0
gateway: 192.168.188.2
hop count: 1
interface: LAN
The device with IP 192.168.188.2 will be connected directly to one of the LAN ports on the router.Will that work to route, trying to get to 192.168.166.0 to the IP of 192.168.188.2?It just seems odd because the packets would hit the router then go back out through the LAN port.
View 4 Replies
View Related
Nov 17, 2011
isco epc3925 in transparent bridge provided by isp with following wan details
ip=x.x.x.120 subnet=255.255.255.248 gw=x.x.x.121 and 2 dns server ip's
I can't get the one-to-one nat working. read in some forums that the rv082 can do the job.
View 4 Replies
View Related
May 9, 2013
I have a Meraki Firewall that sits behind my Cisco RV082. The Meraki is setup to run a VPN connection with my server but I am having problems passing the VPN traffic through properly.
I have 2 Uverse Internet Connections that the RV082 using load balancing so that they are shared. I have 10 static IP's.
I am trying to come in on one of my static IP addresses throught the Cisco RV082 to the Meraki and after doing a capture on the meraki it appears that it is starting to receive data to intiate the VPN connection but when it sends data back to the VPN client machine it never makes it.
View 1 Replies
View Related
Nov 12, 2012
I have reset my RV082 router (both wit the reset switch and the factory default wizard) and run the setup wizard but regardless I can't connect to shaw.ca which is my service provider. I notice that if I use http://192.168.1.1 the browsers (IE & FF) default to https://192.168.1.1 and then I am prompted for a certificate. I can enter if I ignore the request but after getting in I simply cannot connect to my ISP.
View 4 Replies
View Related
Jan 12, 2012
Is it possbile to NAT to other subnets with the RV082. It is on a 192.168.41.x and I have a phone system on a 192.168.20.x. After searching all over others are saying no.
View 4 Replies
View Related
Jan 14, 2013
I just set up a new Linksys/Cisco RV082 router with the intent to get VPN working from outside the building. I have gone through the setup and while everything looks good, I have not been able to connect yet. I have tried everything that I know how, and am now hoping to get the answer from some pros.
Here's my setup. We use Comcast Business class internet. The modem is plugged into WAN port 1 on the RV082. I'm using the router as a DHCP server, that is working fine. My local subnet is 192.168.0.0/220
Right now all I want is to be able to log in as a client using QuickVPN. I set up one user and a client to VPN tunnel using the router's config page. Here's the settings I have:
Tunnel Interface is setup on WAN1, checkbox is enabled.
Local Group Setup
Local Security Gatewaytpe: IP Only
Local Security Group Type: Subnet
[Code]....
It seems like something is blocking the connection, but seeing that I have tried this after disabling the firewall completely it doesn't make sense to me. I also went into the config page for the modem and set up the router as a DMZ. I have also tried connecting with the client built into Windows 7, but that doesn't work either, I just get "connection failed with error 619"
I have the port in QuickVPN set to auto, but have tried both 443 and 60443 with same results.
I ran a port scan at [URL] and it shows I have 3 ports open...80,443, and 1723
View 4 Replies
View Related
Jan 24, 2012
I have a VPN tunnel from one RV082 to another, first router has IP range of 192.168.1.0 and the second one has range of 18.18.18.0, the connection works fine, here is where the issue starts, I am at a PC in the 18.18.18.0 network and I ping an IP in the other one e.g. 192.168.1.50 and it pings fine, but when I try to RDP into it or do anything to it I get no response, is it a firewall issue? Is it a NAT issue? I am at a loss, now that IP i mentioned does have RDP enabled and working because it is being port fowarded in the 192.168.1.0 router and I can access it through the public IP.
Also a workstation with a static IP 192.168.1.18 I can ping it if im in the local network but if I am in the remote one I cannot at all.
View 7 Replies
View Related
Jul 28, 2010
we have an RV082 router that a few days ago started restarting itself after normal usage.The simpton is that when people come to office, starting using the Internet the RV082 resets. It stays online for 3 to 12 minutes and then it resets again.
clicking on Reset to Factory Default in the web interfaceafter the reset, I confirmed that it was reset to factory default I reset it again using the reset buttomre-configure the RV082 manually.I also tested with another identical rv082 (hw version and firmware version) and after doing a backup of the config of the original rv082 and restoring it in the new rv082, the same problem happends.
View 20 Replies
View Related
Mar 15, 2013
I have an RV082 10/100 8-Port VPN Router and have configured the NAT table to allow for remote users, however I've run into an issue. It seems like there is a limited number of entries that you can put in the table,10, and I need to configure about 5 more IPs. Any way to expand the NAT table, or alternatively recommend a different router. I would also be willing to add another router to the network, but I have little experience doing that.
View 3 Replies
View Related
Jul 18, 2012
Are the RV042 and RV082 routers SIP AWARE?I haven't had any luck finding documentation stating such.
View 2 Replies
View Related
Oct 20, 2011
Just purchased a RV082 and once I switched a bunch of users over to it I can no longer access the web admin section. I have tried using both IE and Firefox and have used multiple workstations. I get to the login screen but it doesn't get any further. I am running the latest firmware v4.0.4.2-tm. It works for a while then just stops. The only fix is to turn off the device and back on and then it starts working again.
I've seen this issue on other small business cisco devices and had to stop using this because of this issue and switch to a higher grade cisco product but was hoping that this particular issue would have been resolved now across cisco's products.
View 7 Replies
View Related
Jan 9, 2012
I just migrated our office network router to a RV082. While configuring it, I came across three problems:
(1) From our ISP we have four public IP addresses which I want to make use of for outbound traffic. With the previous router we used we could configure LAN IPs(ranges) to map to static public IPs. Does RV082 support this? I could not find an option for that at the web-interface. From what I understand the 1-1 NATing only goes both incoming and outgoign ways and actually is 1-1 and not the many-to-one I am looking for.
(2) How is it possible to configure incoming port forwards to use a specific WAN interface? Will it always be the primary WAN interface?
(3) Does the telnet access provide more configuration options? I could not log in to it with the same user credentials as with the web-interface.
Serial Number : NKS1532xxxxFirmware Version : v4.0.4.02-tm (Jul 4 2011 13:30:56)PID VID : RV082 V03Firmware MD5 Checksum : 1f84d8d0a2a8b99f9bfa4409e64547aaLANWorking Mode : Gateway
View 0 Replies
View Related
Apr 27, 2013
we have a RV082 and have the DMZ option enable for a range of IPs within the same subnet of WAN IP and this works great. I have another range of Public IPs from our ISP that is not in the same subnet of the WAN IP and do not see a way on the RV082 to include this 2nd bank of Public IPs in the DMZ. Our ISP internet feed plugs into the RV082 WAN port and we have a switch pulgged into the DMZ port of the RV082 that is used to connect the public devices in the current DMZ. Both banks of Public IPs from our ISP come over via the ISP internet feed plugged into the WAN Port. My question is, if I cannot configure a DMZ rule to allow this 2nd range of Public IPs to "travel" to the RV082 DMZ port.
View 0 Replies
View Related
Nov 12, 2012
I would like to set the subnet mask off the lan to 255.255.240.0 but the selection menu do not allow to do it.
View 8 Replies
View Related
Sep 25, 2012
I wanted to know if you can connect a Cable modem to a SA520W, then connect a RV082 to the SA520W?
View 5 Replies
View Related
Mar 24, 2013
We recently moved our network over to RV082 router and its working great, well now we want to take advantage of VPN for our sales staff.
I was able to setup the VPN and using a PC at a remote office I can launch the quick connect and it connects right away, RV0 even shows the user connected. However the user cannot ping anything on our network via name or IP, connect to any resources, etc...
My understanding was when the client VPN would connect the user would get an IP from DHCP (this is on our Server 2008 DC) and they would be using that address, but when I run IPCONFIG on the client PC they just have there standard IP from remote office.
View 8 Replies
View Related
Feb 10, 2013
I'm planning to buy a few Cisco RV082's for remote offices and using them to connect to main office Cisco 2851 site to site vpn. So I guess, simple site to site vpn will work without much problem, but I wonder, will backup vpn feature work as expected on backup WAN channel and how should I configure it on the IOS side?
View 1 Replies
View Related
Jan 19, 2010
The RV082 is a great unit, however when VPN clients connect the QuickVPN Client has a setting to use the Remote DNS settings of the RV082. The RV082 has no way of linking or using a user-defined DNS. I have an internal DNS Server that I would like the VPN Clients to query on internal name lookups (kindof the point of having client vpn, so they can access internal network shares etc. On the diagnostic page the ping and name resolution can only check external DNS and internal IP's. Wouldn't it make sense to at least make the RV082 aware of internal DNS Servers? Then the Ping and DNS lookup would be able to test both zones? Is this something that can be looked at by Linksys Developers for this product? The WRV210 (a cheaper and lower level model) has this functionality.
View 8 Replies
View Related
