Cisco WAN :: Wireless On RV082 Is Slow?
Nov 16, 2010
Material in question:
Router Model: RV082
Firmware: 2.0.0.19-tm
Only primary WAN port used
Description of problem:I've had a 50mbps internet line with a 2mbps upload for a couple of weeks. I thought my ISP was having trouble because I was only getting 30mbps down and 700kbps upload with noticeable packet loss, however after connecting a laptop directly to the modem after office hours, I realized that I can reach 53mbps down and almost 2.5mbps up. But when I connect directly into the router I only reached the much slower speeds mentioned above previously. (40-60% slowdown)All transfers over LAN reach their full 100mbps transfer speed. So it seems to just be a problems with the WAN.My next move is to back up the router, flash it and then try it with basic default configurations to see if a setting is causing the slowdown.On the other hand, it just occurred to me that perhaps the router was not designed for such a fast line. Does the RV082 can handle a 50mbps internet connection? How to successfully deployed such a fast internet line with this router?
View 6 Replies
ADVERTISEMENT
Nov 29, 2009
I've been having trouble with the internet connection speed on my Mac. I originally noticed the problem when my mail kept timing out whenever I sent an attachment, I went to different forums trying to find the solution but nothing really worked, so I found work arounds for the email and lived with it. Recently the company I work for moved offices and I was no longer behind the RV082 and my internet ran better dispite the slower connection. Once we finished moving, I needed to use the Dual Wan Load Balance feature of th RV082 so I set it up in the new office and my internet was slow again. Unfortunatly in the new office there are several more Macs than just mine so I really need to get it working. Currently we have 2 seperate networks for PC and Mac and I really need to get them on 1. Is there a setting I may have overlooked or is it not going to work with Mac.
View 26 Replies
View Related
Feb 18, 2013
I have an RV042 VPN tunnel with an RV082.The RV042 has a public IP Address obtained by PPPoE, the RV082 has a public IP Address obtained via Static IP.The problem I see is a really slow performance. Both internet conections are idle and the performance is about 2 or 3 kbyte/s My question are if I should I enable any of this:
- Agresive mode
- NAT Traversal
- IP Compresion
- Dead Pear Detection
How can I troubleshot this slow performance?
View 2 Replies
View Related
Nov 14, 2012
I'm owner of Cisco RV082 router and I have a problem with firewall setup.I would like to deny internet access on port 80 (all sites) for group of users, and allow them internet access for one site by HTTPS (443)After applying rules internet connection is really slow.. Users have to wait something like a 30 sec for a website..I descovered that the reason for slow internet connection is DENY rule. After disbling DENY rule everything works fine..Now I have a few rules added to firewall:
Priority:1 Action: Deny Service: HTTP(80) Source interface: LAN Source:10.82.0.51-10.82.0.245 Destination: Any
Priority:2 Action: Allow Service: HTTPS(443) Source interface: LAN Source: 10.82.0.51-10.82.0.245 Destination: 80.64.59.42
What's wrong with those firewall settings?
View 1 Replies
View Related
May 7, 2013
With RV082, I need to make a wireless network bridge, what material should I use for a short distance outside - 100m.
View 4 Replies
View Related
Feb 6, 2012
I have a Rv082 router that works great and I added a Cisco wireless Wap4410n to one of the ports and it works great for all my wireless connections. My problem is I cannot set up any security on the wireless connection. I see it on network majic pro but cannot access it thru my router . Do I have to install a poe switch first?
View 0 Replies
View Related
Dec 21, 2012
Region : Others
Model : TD-W8950ND
Hardware Version : V1
Firmware Version : 1.3.1 build 120406 Rel.32903n
ISP : PTCL
I am trying to establish IPSec VPN Tunnel between Linsys RV082 and TP-Link TD-W8950ND but failed.
View 1 Replies
View Related
Apr 19, 2012
I have a Linksys RV082 Wired router. It works great but doesn't do wireless. I have a Cisco/Linksys E2500 Wireless router for my wireless devices to use. the RV082 is on the 192.168.1.x network. The E2500 is on the network 192.168.0.x network. The Internet cable goes to the Wired RV082, and a line comes out of there to the wireless router. This all works fine except for a couple inconveniences.I have an iPad that connects wirelessly and some of the apps offer an http:// option so I can transfer files to that app. I also have a network printer hooked in wired, but wireless devices can't see it.I have 2 problems:
1) In order to transfer files from my laptop (which I have hooked in to the wired network most of the time), I have too disconnect the wire, connect wirelessly, then I can transfer the files. Works, but it's inconvenient.
2) I would like a netbook that I have on the wireless connection to be able to print to my wired network printer.
It appears that the 2 networks are not seeing each other. Here are the things that I have tried:
1) I disabled the DHCP on the wireless router. My thought is that requests for an IP address sent to the wireless router would be forwarded along to my wired router... NOT. On my iPad and Wii, they could no longer connect wirelessly. Strangely enough, with the wire disconnected and connecting wirelessly with my laptop, I was still getting a 192.168.0.x IP address, even though DHCP was disabled on the wireless router.
2) Thinking that I would just manually put the wireless router on the 192.168.1.x network, instead of telling it to get an IP dynamicaly from the Internet connection, I manually set it's IP to 192.168.1.245. Bad mistake. I could not connect to it at all from anywhere then. The only way I could fix that was to hook it wired to my notebook, assign a static IP to my notebook on the same network as the router, then I could got to the setup page and set things back the way it was.
Another thing... Even when I'm only connected wired on my notebook and wireless is disabled, I can ping 192.168.0.1 (the wireless gateway) and it returns a value. But, when I try to go there in a browser, I get a "page not found" error.
View 2 Replies
View Related
May 17, 2013
I have a ASA5510 with VPN Configured on it. My goal is to be able to access our Rv082 Router after connecting to the VPN and from any PC inside the LAN. I don't want to be able to access the ASDM on the ASA5510 or the RV082 from outside the LAN UNLESS you are using VPN.
My Inside IP Subnet is 10.0.1.0/24 on the CISCO ASA5510. The CISCO ASA5510 Outside Interface is 172.16.15.2
The CISCO RV082 (172.16.15.1) is connected to the ASA5510 Outside Interface.
Our VPN Addresses start at 10.0.10.240 and I think they are NATTED to the Inside Interface of the LAN.
At this time, after connecting via VPN, we cannot access the RV082 at 172.16.15.1.but we want to. I think we need a static Route to do this but I don't know which one to add, or how to add it ?
View 2 Replies
View Related
Jan 29, 2013
We have an RV082 setup with WAN to the internet and LAN IP of 192.168.188.1.If I add a static route like so:
network: 192.168.166.0
mask: 255.255.255.0
gateway: 192.168.188.2
hop count: 1
interface: LAN
The device with IP 192.168.188.2 will be connected directly to one of the LAN ports on the router.Will that work to route, trying to get to 192.168.166.0 to the IP of 192.168.188.2?It just seems odd because the packets would hit the router then go back out through the LAN port.
View 4 Replies
View Related
Nov 17, 2011
isco epc3925 in transparent bridge provided by isp with following wan details
ip=x.x.x.120 subnet=255.255.255.248 gw=x.x.x.121 and 2 dns server ip's
I can't get the one-to-one nat working. read in some forums that the rv082 can do the job.
View 4 Replies
View Related
May 9, 2013
I have a Meraki Firewall that sits behind my Cisco RV082. The Meraki is setup to run a VPN connection with my server but I am having problems passing the VPN traffic through properly.
I have 2 Uverse Internet Connections that the RV082 using load balancing so that they are shared. I have 10 static IP's.
I am trying to come in on one of my static IP addresses throught the Cisco RV082 to the Meraki and after doing a capture on the meraki it appears that it is starting to receive data to intiate the VPN connection but when it sends data back to the VPN client machine it never makes it.
View 1 Replies
View Related
Feb 3, 2011
I purchased a RV082 router because it said it would support VLANs, but I cant seem to get it set up how I want.
I would like the first internet port on the router to feed one VLAN with an IP address. I would like the second internet port (DMZ / Internet) to feed a second VLAN with a different IP address. These two VLANs should be completely separate. I can see how to set up VLANs but I can seem to find how to separate the feeds and assign them different IP addresses.
Can I set up the RV082 to do this?
View 1 Replies
View Related
Nov 12, 2012
I have reset my RV082 router (both wit the reset switch and the factory default wizard) and run the setup wizard but regardless I can't connect to shaw.ca which is my service provider. I notice that if I use http://192.168.1.1 the browsers (IE & FF) default to https://192.168.1.1 and then I am prompted for a certificate. I can enter if I ignore the request but after getting in I simply cannot connect to my ISP.
View 4 Replies
View Related
Jan 12, 2012
Is it possbile to NAT to other subnets with the RV082. It is on a 192.168.41.x and I have a phone system on a 192.168.20.x. After searching all over others are saying no.
View 4 Replies
View Related
Jan 14, 2013
I just set up a new Linksys/Cisco RV082 router with the intent to get VPN working from outside the building. I have gone through the setup and while everything looks good, I have not been able to connect yet. I have tried everything that I know how, and am now hoping to get the answer from some pros.
Here's my setup. We use Comcast Business class internet. The modem is plugged into WAN port 1 on the RV082. I'm using the router as a DHCP server, that is working fine. My local subnet is 192.168.0.0/220
Right now all I want is to be able to log in as a client using QuickVPN. I set up one user and a client to VPN tunnel using the router's config page. Here's the settings I have:
Tunnel Interface is setup on WAN1, checkbox is enabled.
Local Group Setup
Local Security Gatewaytpe: IP Only
Local Security Group Type: Subnet
[Code]....
It seems like something is blocking the connection, but seeing that I have tried this after disabling the firewall completely it doesn't make sense to me. I also went into the config page for the modem and set up the router as a DMZ. I have also tried connecting with the client built into Windows 7, but that doesn't work either, I just get "connection failed with error 619"
I have the port in QuickVPN set to auto, but have tried both 443 and 60443 with same results.
I ran a port scan at [URL] and it shows I have 3 ports open...80,443, and 1723
View 4 Replies
View Related
Jan 24, 2012
I have a VPN tunnel from one RV082 to another, first router has IP range of 192.168.1.0 and the second one has range of 18.18.18.0, the connection works fine, here is where the issue starts, I am at a PC in the 18.18.18.0 network and I ping an IP in the other one e.g. 192.168.1.50 and it pings fine, but when I try to RDP into it or do anything to it I get no response, is it a firewall issue? Is it a NAT issue? I am at a loss, now that IP i mentioned does have RDP enabled and working because it is being port fowarded in the 192.168.1.0 router and I can access it through the public IP.
Also a workstation with a static IP 192.168.1.18 I can ping it if im in the local network but if I am in the remote one I cannot at all.
View 7 Replies
View Related
Jul 28, 2010
we have an RV082 router that a few days ago started restarting itself after normal usage.The simpton is that when people come to office, starting using the Internet the RV082 resets. It stays online for 3 to 12 minutes and then it resets again.
clicking on Reset to Factory Default in the web interfaceafter the reset, I confirmed that it was reset to factory default I reset it again using the reset buttomre-configure the RV082 manually.I also tested with another identical rv082 (hw version and firmware version) and after doing a backup of the config of the original rv082 and restoring it in the new rv082, the same problem happends.
View 20 Replies
View Related
Mar 15, 2013
I have an RV082 10/100 8-Port VPN Router and have configured the NAT table to allow for remote users, however I've run into an issue. It seems like there is a limited number of entries that you can put in the table,10, and I need to configure about 5 more IPs. Any way to expand the NAT table, or alternatively recommend a different router. I would also be willing to add another router to the network, but I have little experience doing that.
View 3 Replies
View Related
Jul 18, 2012
Are the RV042 and RV082 routers SIP AWARE?I haven't had any luck finding documentation stating such.
View 2 Replies
View Related
Oct 20, 2011
Just purchased a RV082 and once I switched a bunch of users over to it I can no longer access the web admin section. I have tried using both IE and Firefox and have used multiple workstations. I get to the login screen but it doesn't get any further. I am running the latest firmware v4.0.4.2-tm. It works for a while then just stops. The only fix is to turn off the device and back on and then it starts working again.
I've seen this issue on other small business cisco devices and had to stop using this because of this issue and switch to a higher grade cisco product but was hoping that this particular issue would have been resolved now across cisco's products.
View 7 Replies
View Related
Jan 9, 2012
I just migrated our office network router to a RV082. While configuring it, I came across three problems:
(1) From our ISP we have four public IP addresses which I want to make use of for outbound traffic. With the previous router we used we could configure LAN IPs(ranges) to map to static public IPs. Does RV082 support this? I could not find an option for that at the web-interface. From what I understand the 1-1 NATing only goes both incoming and outgoign ways and actually is 1-1 and not the many-to-one I am looking for.
(2) How is it possible to configure incoming port forwards to use a specific WAN interface? Will it always be the primary WAN interface?
(3) Does the telnet access provide more configuration options? I could not log in to it with the same user credentials as with the web-interface.
Serial Number : NKS1532xxxxFirmware Version : v4.0.4.02-tm (Jul 4 2011 13:30:56)PID VID : RV082 V03Firmware MD5 Checksum : 1f84d8d0a2a8b99f9bfa4409e64547aaLANWorking Mode : Gateway
View 0 Replies
View Related
Apr 27, 2013
we have a RV082 and have the DMZ option enable for a range of IPs within the same subnet of WAN IP and this works great. I have another range of Public IPs from our ISP that is not in the same subnet of the WAN IP and do not see a way on the RV082 to include this 2nd bank of Public IPs in the DMZ. Our ISP internet feed plugs into the RV082 WAN port and we have a switch pulgged into the DMZ port of the RV082 that is used to connect the public devices in the current DMZ. Both banks of Public IPs from our ISP come over via the ISP internet feed plugged into the WAN Port. My question is, if I cannot configure a DMZ rule to allow this 2nd range of Public IPs to "travel" to the RV082 DMZ port.
View 0 Replies
View Related
Nov 12, 2012
I would like to set the subnet mask off the lan to 255.255.240.0 but the selection menu do not allow to do it.
View 8 Replies
View Related
Sep 25, 2012
I wanted to know if you can connect a Cable modem to a SA520W, then connect a RV082 to the SA520W?
View 5 Replies
View Related
Sep 20, 2012
I've set up this router in the office, and I can access it via PPTP without any problems from home (via windows VPN), Router is sat in DMZ with full access to the internet.
Q1,I've created a 2 phase ipsec vpn with an IKE & preshared key (AES/MD5/1), but I can't find out how to get my encrypted hash for it?also, I can't access the IOS via telnet/ putty, I found an article online explaining how to enable it via url string, but it didn't work,
Q2,I've setup the cisco client on my laptop, and working on the pcf file, without much luck.. Everytime I try to connect it get " error 412. the remote peer is no longer responding. "
With wireshark, I can see the requests been made to the router.. ( from the office )
Within my PCF file i have ...
[main]
Description=MYNAME
Host=<external IP>
AuthType=1
GroupName=vpnname
GroupPwd=<myUnEncryptedKey>
[code]....
View 1 Replies
View Related
Mar 24, 2013
We recently moved our network over to RV082 router and its working great, well now we want to take advantage of VPN for our sales staff.
I was able to setup the VPN and using a PC at a remote office I can launch the quick connect and it connects right away, RV0 even shows the user connected. However the user cannot ping anything on our network via name or IP, connect to any resources, etc...
My understanding was when the client VPN would connect the user would get an IP from DHCP (this is on our Server 2008 DC) and they would be using that address, but when I run IPCONFIG on the client PC they just have there standard IP from remote office.
View 8 Replies
View Related
Feb 10, 2013
I'm planning to buy a few Cisco RV082's for remote offices and using them to connect to main office Cisco 2851 site to site vpn. So I guess, simple site to site vpn will work without much problem, but I wonder, will backup vpn feature work as expected on backup WAN channel and how should I configure it on the IOS side?
View 1 Replies
View Related
Jan 19, 2010
The RV082 is a great unit, however when VPN clients connect the QuickVPN Client has a setting to use the Remote DNS settings of the RV082. The RV082 has no way of linking or using a user-defined DNS. I have an internal DNS Server that I would like the VPN Clients to query on internal name lookups (kindof the point of having client vpn, so they can access internal network shares etc. On the diagnostic page the ping and name resolution can only check external DNS and internal IP's. Wouldn't it make sense to at least make the RV082 aware of internal DNS Servers? Then the Ping and DNS lookup would be able to test both zones? Is this something that can be looked at by Linksys Developers for this product? The WRV210 (a cheaper and lower level model) has this functionality.
View 8 Replies
View Related
Aug 21, 2011
Linksys RV082 router is configured to establish a single VPN tunnel. Everything works just fine until powerfail occurs, because VPN connection must be then initiated by clicking "connect" via web-interface. Is there a possibility to automate VPN-connection on start-up?
View 1 Replies
View Related
Aug 29, 2012
Experiencing a strange issue with v3 hardware. After a short period of time, I cannot log into the web administration - either locally through standard port or remote through non-standard port get login prompt, enter correct username & password, page refreshes with blank background and first page (status?) never shows.power cycling the router restores access to the web administration page, for an uncertain period of time before it barfs again.
I was running older firmware, updated to newest 4.2.1.02 (?) and same problem. Only thing that is better is the internet didn't completely lock up when I tried to access the administration page, like it did on the older firmware.
View 4 Replies
View Related
Dec 1, 2010
I have an RV082 for use in our office. I wanted to create a public acess point on a different subnet/vlan and so configured port 8 of the RV08 as VLAN2. When I plug a laptop into this port it immediataley gets an IP address from the DHCP server on VLAN1 and can communicate with the rest of the network.I thought the whole point of the VLAN option was that this shouldn't happen - what I've incorrectly configured?
View 17 Replies
View Related
Jul 13, 2012
I have an old RV082 that I suppose has failed. The red diag light on the front panel is lit and nothing works. I've already replaced the unit, so I don't really need to fix it. Here's my issue: the setup on the old unit was pretty complex with a number of port forwards and other non-default settings. I'd like to recreate those items on my new router, but they were never written down so I don't know what they were. I've tried to connect a computer to one of the LAN ports, but they're all dead. Is there any way to get at the configuration page?
View 2 Replies
View Related
