Unable To Find Wep Supposed To Be On Back Of Router?
Sep 19, 2012cannot find wep supposed to be on back of router
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: HWIC-4SHDSL-E Router Back To Back Connection?
Apr 11, 2013I have two site that has a copper wire ( 2 wire) connection between each router ( No Telco in between ). Now I want to use 1921 router with HWIC-4SHDSL-E card to connect these two site together. Can I use attach configuration to make the connection reference from the diagram ?
View 1 Replies View RelatedCisco Switching/Routing :: Connecting 2650XM - 2620 Router Back To Back WIC - T1?
Nov 25, 2011I have 2650XM router and 2620 Router Both routers have built in WIC T1 CSU/DSU cards
2620Router --
2620Router#sh int se0/0
Serial0/0 is down, line protocol is down
Hardware is PQUICC with Fractional T1 CSU/DSU
Description: DTE side
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
[code]....
My question is that cisco website says there are two type of cable connections for this type of config --which are --T1 CSU/DSU ConfigurationSet one CSU/DSU to clock source internal, and the other CSU/DSU to clock source line. The linecode, framing, data-coding, and timeslots must be set the same on both CSU/DSUs.Four-Wire 56k CSU/DSU Configuration For my network connection which type of config i should use??Secondly i try to connect these ports by normal crossover cable it did not work.So for this type of connection i know i need T1 cross over cable-- which has RJ 48 connections at both sides.I check cable from ebay which is RJ45 RJ48 cross over -- will this cable work in my router to router connection.
Cisco WAN :: 1921 / Connect Two Router Back To Back Via 2 Pin Copper Wire?
Jan 8, 2013I would like configure two router (e.g. 1921) back to back via a 2 pin copper wire. Can I use HWIC-4SHDSL-E card to do it? What is the configuration I can use?
View 7 Replies View RelatedCisco WAN :: HWIC-4SHDSL-E Router Back To Back Connection
Apr 14, 2013I have two site that has a copper wire (2 wire) connection between each router ( No Telco in between )Now I want to use 1921 router with HWIC-4SH DSL-E card to connect these two ste together.Can I use attach configuration to make the connection reference from the diagram?
View 2 Replies View RelatedBelkin Routers :: F7D6301 V1 Can't Seem To Find That Page Again So Can Switch It Back
Mar 31, 2013I turned a Belkin Surf N300 into an access point using the settings page via IP address, now I can't seem to find that page again so I can switch it back. The model number is F7D6301 v1.
View 7 Replies View RelatedCisco Wireless :: AP541N What POE Injector Are Supposed To Be Used
Jan 30, 2011AP541N wireless AP, what POE injector are you supposed to use?The web site states any enterprise class af POE injector will do, but the AP1131 POE injector does not work with the AP541N.
View 5 Replies View RelatedNetgear N600 - USB Wireless Adapters Supposed To Be Unstable?
Jan 14, 2013I bought a Netgear N600 wireless adapter (WNDA3100).I used wired before mostly without problems but was annoyed by the cables.My router is a Netgear WNDR3300 and I never had problems with it.The problem is that sometimes my wireless adapter just stops working and drops the connection.I use it since a few days, and it already happened several times.It happened especially when I was streaming videos to my PS3 (my PS3 is also wireless). It also happened while I was watching Youtube videos. When this happens, I need to unplug the adapter and plug it again. Sometimes, I need to restart the whole computer for my adapter to work again.Is this normal with USB wireless adapters? This is unacceptable to me.I want a stable connection.
View 2 Replies View RelatedRatio Supposed To Be Between Download / Upload Speed In Normal Working Configuration
Jan 2, 2011What is the ratio supposed to be between the download speed and the upload speed in a normal working configuation? My webpages are taking forever to load. I used this speedtest... url...
-download speed: 7.427 Mbps
-upload speed: 0.006 Mbps
My provider is cable, Brighthouse, hooked up to their Scientific Atlanta modem and from there it is hooked up to a Belkin Connect N150 wireless router. I am not using the wireless on my laptop but am wired directly to the router. [code]
D-Link DIR-825 :: Unable To Connect Through External IP Back Into Server On Applications?
Aug 7, 2011Just updated to the 1.01 firmware on my DIR-815 and now it doesn't handle loopbacks anymore.
For instance, I have a dyndns address of ericnewton76.dyndns.org. This points to my router. Works fine if you're NOT within the router's internal network, ie, outside hosts can get in just fine (try it... http:// , you'll see an IIS7 welcome screen)
However, when INSIDE the network, the requests don't get connected properly, and they used to... ie, I work with code, so my svn repo is at ericnewton76.dyndns.org/svn but inside my network it doesn't connect properly anymore (whereas it used to before firmware update)
So now I wish I could back-peddle to 1.0 firmware.
Cisco DPQ3212 - Unable To Connect / Find Wireless Router
Aug 24, 2012Make and Model Cisco DPQ3212 (Modem)Netgear N600 Wireless Dual Band Gigabit (Router)So when I first got the router and modem and hooked it all up everything worked. Then the inter got shut off for a day then came back on and now the only way I can use it is by Ethernet cord. This would be fine but, unfortunately the Xbox in in the living room nowhere near the router. I have tried power resets and everything else the companies of both tell you to try but nothing is working.
View 8 Replies View RelatedLinksys Wireless Router :: E1000 - Unable To Find Out Cisco Codes
Dec 2, 2011I am trying to connect to my wifi with my wireless router it is a cisco linksys e1000 and and I tried connect and it said error so I went to manual set up.and couldn't figure out the codes to enter I couldn't find the cisco codss on the nintendo website.
View 1 Replies View RelatedCisco Firewall :: VPN Tunnel Built Via ASA5505 But Unable To RDP / ICMP Back To Internal Network
Oct 10, 2012I'm able to build my tunnel but unable to RDP nor ICMP back to the internal network.
VPN Client IP: 192.168.200.200
INTERNAL IP: 172.17.130.200
my configuration is below:
HOME-ASAFW02(config)# wr t: Saved:ASA Version 8.4(4)!hostname HOME-ASAFW02domain-name hsd1.nj.comcast.netenable password ViPq56cvd3SGvB08 encryptedpasswd 8bcozHCAwCqA5BmN encryptednames!interface Ethernet0/0description OUTSIDE-Connectionswitchport access vlan 2switchport protected!interface Ethernet0/1description INSIDE-Connectionswitchport protectedspeed 100duplex full!interface Ethernet0/2description WiFi-LinkSYSswitchport access vlan 3switchport protected!interface Ethernet0/3shutdown!interface Ethernet0/4shutdown!interface Ethernet0/5shutdown!interface Ethernet0/6shutdown!interface Ethernet0/7shutdown!interface Vlan1description INTERNAL-Networknameif insidesecurity-level 100ip address 172.17.130.129 255.255.255.128!interface Vlan2description OUTSIDE-Link-to-ISPnameif
[code]....
Cisco Switching/Routing :: 2691 / 6500 - Unable To Ping IP Of IBGP Nei Loop Back
Apr 6, 2012Here is my Lab Setup: 2691 is BGP nei to R4 router and they are not directly connected. 2691 and R4 are in same AS 6500. 2691 Config---router ospf 1 network 3.3.3.3 0.0.0.0 area 0 . Its advertising its loop back IP to OSPF domain.
router bgp 6500
no synchronization
bgp log-neighbor-changes
neighbor 6.6.6.6 remote-as 6500
neighbor 6.6.6.6 update-source Loopback3
[code]...
R4 Router
router ospf 11
log-adjacency-changes
network 6.6.6.6 0.0.0.0 area 0
[ code].....
We can see that 2691 and R4 are BGP neis and 2691 has 200.1.x.x routes in its route table. My question is why from 2691 router i am unable to ping any route learned by BGP from R4?
2691Router# ping 50.1.1.0 Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 50.1.1.0, timeout is 2 seconds:.....Success rate is 0 percent (0/5)2691Router#ping 200.1.2.0 [ code]...
Cisco Switching/Routing :: ATM 8510 Back To Back With 7206vxr 155Meg Only Get 44Meg?
Nov 25, 2012I have a Cisco 8510msr that is connected back to back with a 7206vxr across a 155Meg connection.I receive lots of Output drops on the 7206vxr interface facing the atm switch. When I do the following command:-
kwdair9#sh atm int atm 1/0Interface ATM1/0:AAL enabled: AAL5 , Maximum VCs: 4096, Current VCCs: 27 Maximum Transmit Channels: 0Max. Datagram Size: 4528PLIM Type: SONET - 155000Kbps, TX clocking: LINECell-payload scrambling: ONsts-stream scrambling: ON797522 input, 881483 output, 203946630 IN fast, 223768062 OUT fast, 0 out dropVBR-NRT : 110288 Avail bw = 44712 <====
I only have 44megConfig. is ACTIVEkwdair9# I only get 44Meg of the available 155Meg.There is no QOS on the router and the only commands I can find that vaguely see that refer to QOS are on the ATM switch:-
atm address 47.0091.8100.0000.0007.0d87.b201.0007.0d87.b201.00atm router pnnino aesa embedded-number left-justifiednode 1 level 56 lowest redistribute atm-static?why this is acting like a DS3 link and not a 155Meg link?
Cisco Switching/Routing :: Connecting Two 2951 Back To Back Through A HWIC-4T1 Card
Dec 4, 2011What cable I need to connect two 2951 back to back through a HWIC-4T1/E1 card ?
View 1 Replies View RelatedCisco Switching/Routing :: 2611 / 2801 - Configuration For Back To Back Support
Oct 19, 2012I have 1 2611xm router and 1 2801 router. For my own lab purpose, i want to configure them back to back to support voice services. I don't know what configuration will be required at each end. in 2611xm, i have NM-2V and its also detecting the card, so i hope it will work ? also what commands i need to run on both ends .
View 1 Replies View RelatedCisco WAN :: E1 Clocking Back To Back 3925 Routers
Feb 29, 2012Just to get this clear as having issues with a E1 link with CRC's at one.Router A,Network-Clock-Participate WIC 1,Should router B have clock participate for WIC 1? We currently have controllers set as UNFRAMED but guess we can set to NO-CRC4 both ends and telco will pass this.
View 1 Replies View RelatedCisco Routers :: Connecting Two RV082 Back To Back
Jan 7, 2013I'm looking for instructions on how to setup and connect two RV082 routers together with a crossover cable between their WAN ports. This is to connect two separate LANS together via an ethernet connection. For staging we are setting everything up with a crossover cable in our shop. Ultimately the crossover cable will be replaced by a microwave link between the two LANS several miles apart. There will be no internet connection.
View 7 Replies View RelatedCisco WAN :: 1841 Securing E1 Back-to-back Connections
Aug 28, 2012securing a back-toback connection using E1.The connection is between two cities, using 2x CISCO 1841 router + VWIC-1MFT-E1 interface at each city.
The E1 connections has been provided by our local telco, and they are completely private. The customer is a bank, and they asking me if this is a secure connection or not. If possible, we need to guarantee that no body can get access to the bank network even if they brought E1 modem at one of the ends (telco PoP).
Cisco WAN :: Connecting Two 878 G.SHDSL Routers Back To Back
Apr 7, 2013I searched a lot but couldnt find a clear document about connecting 2 G.SHDSL routers back to back.First of all I am not sure which type of cable (RJ11) is used for connecting two 878 routers. Does it have to be cross or straight cable.
Which RJ11 pairs will be connected each other [code]
According the configuration samples One router must be CPE and the other must be CO for simulating DSLAM.
Cisco WAN :: 888 SHDSL Routers Back To Back
Dec 15, 2011I'm having some trouble getting two Cisco 888's to work correctly back to back.. The two routers will ultimately be used in conjunction with a BT EPS8 circuit which is effectively four wires short distance between customer sites. We have configured lots of these using the older Cisco 878's.
Anyway, as i've been struggling to get line sync on site I've gone back to basics and connected the two 888's back to back. However, I've found that no matter what I do I can only get the routers to sync at 384kbps!? And that's with a one meter RJ11-RJ11 cable.. Very strange. When we've used the 878's we get much more bandwidth. I have tried statically assigning the line rate at both ends but it still only works at 384kbps.
Cisco WAN :: 2901 Back To Back BRI Using WIC-1B-S/T-V3
May 26, 2013I am setting up my lab using two 2901 routers which is running on 15.2 IOS.I am trying to simulate a back to back BRI.BRI Module: WIC-1B-S/T-V3 (x2) one of each router.
I followed this amazing document to understand the concept of BRI and configuration. url..but it never says if i can use the module that i have mentioned.
Q1. What cabling i need to use to setup back to back BRI using 2x 2901 routers with these modules?
Q2. What cabling do i need to use.
Q3. Is it actually possible to use these 2 modules alone to simulate a back to back BRI..?
Unable To Find Any Network
Sep 18, 2011im trying to find avilable netwoks but when i try it says non can be found and i cant connect Wirless .
View 1 Replies View RelatedUnable To Find Vertical Enclosure 10 X 4 X 4
Dec 20, 2011I have CAT-5e cabling running from ceiling to floor and need to enclose this as it's quite an eye-sore. I am looking for a 10' x 4" x 4" vertical enclosure but cannot seem to find any unit that is >84".
View 8 Replies View RelatedPC F5D7632-4 - Unable To Find Network
Jun 26, 2011I have my downstairs PC (Windows Vista 64 bit) conncted to a Belkin router. model F5D7632-4. This works without any problems.Upstairs, my son has a PC (Windows XP) that connects via a Belkin USB G Network Adapter, model F5D7050, version 4.000uk. This worked perfectly, too.He has just got a new PC which I have bought from a friend. My friend used the tower of a previous PC my son had, which had died about 4 years back when the PSU blew and took everything out with it, and fitted the motherboard, graphics card, HDD, RAM etc etc (it uses Windows 7).
I downloaded the latest drivers from the Belkin site, installed them, but for the life of me, the new PC will not detect the network connection. At all. It doesn't find anything.So, I unplugged my PC from the router, and plugged the new PC into it. Unsurpisingly, it connected to the net without any problems. The next thing I did was to reconnect my PC to the router, and try my son's new PC wirelessly again with the Network Adaptor, in the same room. Again, it just doesn't find a network at all.The PC detects the Adapter being plugged in and out, and the light is on on it. I even tried his old PC with the Adapter, and that still finds the network perfectly.
I was on the phone to Belkin for 35 mins yesterday, and they went through everything, to no avail. They think the USB slots may be faulty, even though the PC knows when i'm plugging things into them.
Unable To Find Wireless Networks
Jan 16, 2011I have a laptop that won't find any networks, it did work a few days ago now it's just randomly stopped.Things I've tried;
-Changing the wireless to different channels.
-System restore to a few days before.
-Check and restarted the wzc serice mutiple times.
-Check the drivers are ok.
Laptop Is Unable To Find Any Networks
Jul 16, 2011Recently, I have found out that my laptop is unable to find any networks. I started using what I believe to be an ethernet cable to connect my laptop to the internet because it was faster than wireless. But when I removed the cable and try to connect wirelessly, the computer states that there are no wireless networks in range. I know the wireless adapter is broadcasting because my sister can connect wirelessly to the internet. My WiFi is on, but I can't find any networks.
View 10 Replies View RelatedUnable To Find Wireless Connection On PC?
Jun 28, 2011A week ago I accidently clicked the disable icon on wireless network connection on the bottom right icon on my PC screen. I quickly reversed this but now for some reason, all the wireless networks that are around me cannot be picked up on my Phillips Freevents Windows XP.it was able to pick up two wireless connections and now, not even a trace of one. The other laptops in the house can pick up the wireless connections so I know its working.The internet works when the box is connected to the computer but I need the box in another room so wireless is essential.
View 2 Replies View RelatedUnable To Find Printer On Network
Jan 23, 2012i am having real issues with my printer, i have a network of 3 computers and it was attached to a printer that worked fine, i then changed the printer for a new one and i am now unable to find this printer on my network. i have installed drivers on the computers. how do i find the printer. the network works fine with everything else.
View 4 Replies View RelatedUnable To Find Network Security Key
May 23, 2012I want to change my network, but unable to, because they keep asking about a security key. What is it and how do I find it?
View 1 Replies View RelatedCisco :: IKE Initiator Unable To Find Policy?
Nov 1, 2011I keep getting this on a site to site VPN tunnel that I have established to one of our remote offices. EVERYTHING works fine except for the phones. Everytime they try to connect I get a flood of the below error3Nov 01 201116:06:38IKE Initiator unable to find policy: Intf DS3, Src: 10.90.4.6, Dst: 10.10.20.2010.90.4.0 is our phones vla10.10.20.0 is the remote site network .20 is one of the ip phones located thereried running it through packet tracer and get this...I'm not sure where the problem is, as I said ALL domain traffic is flowing back and forth with no issues.
View 12 Replies View RelatedUnable To Connect To Internet - Cannot Find IP Address
Mar 10, 2011My computer won't access the internet. I have wireless and can get online, but my computer can't find my ip address???
View 9 Replies View Related
