I have a 3560 connected to an edge device and I keep etting this error. I have turned off proxy arp and turned off ip cef under the interface, however I lot connectivity to the internet when I did that. I can't seem to find any documentation on this error. I understand what it means, I just don't know how to resolve the problem.
View 3 RepliesI have a 3560 connected to an edge device and I keep etting this error. I have turned off proxy arp and turned off ip cef under the interface, however I lot connectivity to the internet when I did that. I can't seem to find any documentation on this error. [code]
View 5 Replies View RelatedI upgrade the IOS of my switch 3560 from C3560-IPBASE-M), Version 12.2(25)SEB4, To C3560-IPBASEK9-M), Version 12.2(55)SE5 after that the utilizatio of the memory increase to 80% I attached the output of show memory statistics history
View 5 Replies View RelatedI'm running IP Base on my Catalyst 3560. I'm aware of the fact that this license only allows for EIGRP stub routing - this is desired. However, I don't seem to be able to run the "no auto" command to disable auto-summarization. The command works, but doesn't make it into the running config.
3560-1(config-router)#no eigrp stub connected
EIGRP is restricted to stub configurations only on this platform.
3560-1(config-router)#no auto
[Code].....
Not a huge deal since a "show ip prot" indicates that auto-summarization is already disabled, so I'm guessing this is why "no auto" will not take. Why auto-summarization is disabled by default in my scenario?
According to my boss every 3 to 4 months he has to restart our 2821 with a 16-esw module installed because of a low memory issue dealing with CEF. Here is the exact error message.
%% Low on memory; try again laterJun 8 11:18:51.777: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" Jun 8 11:19:51.823: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" %%
Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
Jun 8 11:20:51.868: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" Jun 8 11:21:51.914: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed
Today, one of our Cisco 3750 got unmanaged from NOC, we were able to ping the switch, also, traffic was flowing fine but not able to telnet or local login.On trying to login through console following messages were coming:
%% Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
[code].....
We given power on reset, after which we were able to login switch again. I wanted to know the actual reason behind it and if there is any other way to recover switch other than power reset.?
ISRG2 (c2951-universalk9-mz.SPA.152-4.M1.bin) has 512 MB of DRAM. Periodically it runs out of memory: [code]
1. Why "show process mean" command shows less memory than 512 MB? Processor Pool (248 MB) + I/O Pool (58 MB) ~ 310 MB only?
2. *Init* process holds more memory than normal (202 MB). What may cause this?
have 3 Catalyst 3750 in same stack, the IOS version is 12.2(53)SE2. Today we can not telnet/ssh to this switch, but ping is ok, and switch function is ok. I try to access the console port, it show "low on memory, try again later". After I reboot the master switch in the stack, the master switch change to another switch, then I can telnet/ssh to this switch. I check the Ciscoworks server syslog report, there are many MAC address flapping error message, and I beleive the MAC address flapping occured before several weeks. ( the G2/0/15 & G3/0/15 is connect to a VMware ESX server and the EtherChannel config mismatch with this Catalyst 3750 switch ) How to mention the root cause of the "low on memory" problem and what is the abnormal memory usage ( free memory percentage below ?% )?
View 5 Replies View Relatedi have a Ws-C3550-24-Emi switch and i need to upgrade its flash memory to 32Mb. I couldn't find any documents in cisco website about the memory upgrade guideline. Possible to upgrade this switch to 32Mb? If so, what's the max of memory i can upgrade? and the part number for this type of memory?
View 4 Replies View RelatedI have a bootflash in 4507R with the size of 60MB. I upgraded the ios from cat4500-ipbasek9-mz.122-37.SG1.bin (12.8MB Size) to cat4500-entservices-mz.122-37.SG1.bin (13.8 MB SIZE) and deleted the previous IOS.But previous IOS is still getting shown in sh bootflash: command. Furthermore, dir bootflash: commands shows there is only one IOS , which is running. How I can free the space from bootflash , as I again have to upgrade the another new IOS ( of 16MB), which I tried through solarwinds tftp and couldn't upload successfully because of its limitation. Now, If I try to upload the new IOS through FTP, it gives me memory space error. How I can free the space captured by old IOS and also how I can delete the 3rd unknown entry of IOS (shown below output of commands)?
View 4 Replies View RelatedI am noticing high memory used on my 2960-S I am running 15.0(2)SE. I am concerned that there is a problem with this model and IOS.
View 2 Replies View RelatedI have a Switch WS-C3750E-48PD-SF with IOS 12.2(58)SE2 which reports more than 80% in utilization of memory I don't know what is causing the high memory utilization.
View 14 Replies View RelatedRecently i atsrt having problems with my cisco router 1811/k9, apparently was booting continiosly when restarted.
After i connected my console i found the problem while booting:
DDR memory test failed. Resetting the router ...
I tried to contact cisco TAC, but i need a reseller contract number to place a ticket, i do not have a resller contract number as my router was bought more than two years ago. I called cisco support and they told me to contact my reseller, my reseller told me to contact cisco so i am in a eternal loop of forwarding phone calls...
which process is consuming high memory with my c6509 switch.
View 17 Replies View RelatedI've noticed that my 6509's running VSS seem to have high I/O memory utilization.
I/O memory: Sw/Mod Bytes: Total Used %Used
1/1 8126344 7886544 97%
1/2 11796240 11442472 97%
1/5 RP 12058384 10715832 89%
1/5 SP 8388608 8104304 97%
1/7 8126344 7886544 97%
[code]....
I managed to upgrade this C2960G-48TC-L from 12.2.35-SE5 to 15.0.2-SE1 and now I can't connect anymore via telnet nor ssh. Console output simply shows
%% Low on memory; try again later
I noticed on the 2960 switches we have deployed that are running the latest IOS, 12.2(58)SE2, memory utilization is really high (almost 80 percent). I have not noticed any side effects but I wanted to verify this is acceptable. My question is does the high memory utilization matter? I see this may be related to bug CSCtw83946 but no resolution is mentioned.
I did some testing various IOS revisions and below is what I have found using a WS-C2960-48TC-L with default configuration and only my laptop connected to a switchport in vlan1. You will notice memory utilization will grows with each version but jumps drastically with 58. One difference with 58 I needed to use a different command to retrieve memory utilization. The output was gathered by pasting the output of the show command into the Cisco Output Interpreter on their website.
IOS
Show Command
Output
c2960-lanbasek9-mz.122-35.SE5.bin
show memory
[Code]....
router 2811 has 2 files ios in flash
Router#sh fla
-#- --length-- -----date/time------ path
1 35202336 Mar 3 2008 16:12:28 +00:00 c2800nm-adventerprisek9-mz.124-8d.bin
...
13 59374168 Mar 5 2012 12:49:22 +00:00 c2800nm-adventerprisek9-mz.124-24.T.bin
151076864 bytes available (105431040 bytes used)
Router#
I try to make it load c2800nm-adventerprisek9-mz.124-24.T.bin
[Code] ...........
I did
verif flash:c2800nm-adventerprisek9-mz.124-24.T.binit is ok
is it corrupted memory? how to fix it?and aslo with System image file is "flash:c2800nm-adventerprisek9-mz.124-8d.bin"it dos not show voice ports for WIC2-FXO in runn conf
We have a Cisco 2911 router. We installed a EHWIC-4ESG module and configured the router based on configuration below.
ROM: System Bootstrap, Version 15.0(1r)M9, RELEASE SOFTWARE (fc1)
System image file is "flash0:c2900-universalk9-mz.SPA.151-4.M1.bin"
Cisco CISCO2911/K9 (revision 1.0) with 483328K/40960K bytes of memory.
7 Gigabit Ethernet interfaces
1 terminal line(code)
We have a pair of 6513s and upgraded the IOS version to 12.2(33)SXI4a. After the upgrade we noticed VTP Pruning was disabled: [code] Is there any effect to production we need to to consider when re-enabling? (In other words, do we need to wait until a maintenance window to enable?)Also, we are using VTP v2 (and v1...) on our VTP Client 3560 access switches.
View 2 Replies View RelatedI just want the switch to be quiet so that I can perform some network testing with only the connected hosts showing up in my traffic analysis program. But every 30 seconds or so the switch sends out an LLDP packet. This switch is only used in the lab for running tests so I know I don't need the LLDP feature running.
This article explains how to disable LLDP globally on a Catalyst switch, but I can't find any option to disable LLDP in the SGE2000's configuration menus.
I have a major problem with our core 2801 router. In summary it appears that a staff member disabled password recovery, deleted the IOS and rebooted. Net result is no Rommon and no IOS on the flash. I've read that the Conf-Reg will be reset if I remove the NVRAM but I cannot identify it on the board. If I can get to Rommon I can recover. Currently I don't have Flash reader to restore to flash.
View 2 Replies View Relatedi have enabled error disbled recovery with time interval of 600 seconds on my 2960 switch.
What exactly this command does? Pls explain
I am facing high memory utilization in Cisco 2960 switch having IOS version 12.2(55)SE3.
The error we are getting is:
A "LiveHealthAlarm" event has occurred, from SwCiscoIOS device, named Switch2960. eHealth Alarm Start Time - Fri 09 Nov,2012 - 03:02:48 eHealth. Switch2960-RH-MemoryPool-Processor-Processor-1.Memory utilization high-Threshold set at 70%SPECTRUM ALARM ID|22233284 I have attached the logs also.
We are having 3750 Stack switch as our edge switch. Here we are having some issues as low memory & itermediate High CPU utilization.For memory when we checked its shwoing maximum memory is allocated to DHCPD receive & ARP Input as follows
Processor Pool Total: 70829380 Used: 56809532 Free: 14019848
I/O Pool Total: 12582912 Used: 8554920 Free: 4027992
Driver te Pool Total: 1048576 Used: 40 Free: 1048536
[code].....
i want to understand why this 2 proceses (DHCPD & ARP input) taking more memory?High CPU: We also facing intermediate high CPU utilization (above 95%). When CPU is high there were 2 processes consuming more CPU are 'Spanning Tree' (about 20%) & ARP Input (about 66%). we also checked the ARP entries, there were 1500 ARP entries & 2 incomplete ARP (out of 6000 ARP supported)
I am troubleshooting memory leaks and buffers issues on my 1900 and had some doubts regarding the problems that my router causes.Intermitently during the day for no reason the gig0/0 interface connected to ISP stops responding from our management network (log shows that the interface goes down). The ISPs modem responds fine from my management network.The issue goes away by itself in 20 minutes, sometimes more or after a hard reboot.Sometimes a router would increment a throttle value to 1. When running for 4 days without a reboot, the router raised 39 throttles and 57 input drops. [code] The router is running Version 15.1(2)T4 and I was not able to find any caveats on cisco web page (although I havent used the bug finder tool)Is this only leak I found a reason to start worrying or I can disregard it and continue basic troubleshooting (change cable and plug my ISP to another port)
View 3 Replies View RelatedI have a new cisco 3750 stack comprised of 8 members (6 x 3750G-48PS and 2 x 3750V2-48PS) running 'c3750-ipservicesk9-mz.122-58.SE2.bin'. I am seeing high memory utilisation, it seems to sit fairly stable and I do not see an increase but this has only been running a few days. No errors or performance issues. Should this be a cause for concern?
View 3 Replies View RelatedBelow memory status alerts of are seen on our syslog server for Nexus 7K switch(Default VDC).
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : CRITICAL ALERT RECOVERED
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : MINOR ALERT RECOVERED
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : SEVERE ALERT RECOVERED
Memory threshold Not created on Nexus. Can we ignore this alert or does it impact our current network traffic?
We had a stack of 4 qty 3750g running IP base on ver 12.2.32, then installed a 3750x to the stack and upgraded the whole stack to 15.0.2 SE3. In doing so, we noticed that the memory utilization jumped from 60-70% to 83-84%.
We had the same issue occur when upgrading to 15.0.2 SE3 on another stack that was 6 qty 3750g running ip-services, but this one jumped to 90%. On the 6 qty stack, we downgraded to 12.2.55 and the memory util went back down to 60-70%.
On the mixed stack, we replaced the 3750x with another 3750g and downgraded the whole stack to 12.2.55, however, the memory utilization did not drop down. As far as I can tell, no config changes have changed from the original IOS.
Since yesterday, i see
Nov 16 13:23:21.355: %SYSTEM_CONTROLLER-3-MORE_COR_ERR: 255 correctable DRAM memory errors in previous hour
Nov 16 13:23:21.355: %SYSTEM_CONTROLLER-3-COR_MEM_ERR: Correctable DRAM memory error. Count 623, log 8053C830
Nov 16 14:23:21.340: %SYSTEM_CONTROLLER-3-MORE_COR_ERR: 255 correctable DRAM memory errors in previous hour
Nov 16 14:23:21.340: %SYSTEM_CONTROLLER-3-COR_MEM_ERR: Correctable DRAM memory error. Count 879, log 8053C810
error on switch console every hour.
ios version : Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXJ1, RELEASE SOFTWARE (fc2)
We have a 3750 stack with a mix of 3750G and 3750X switches. The current active template on the switch is desktop default and we are running EIGRP on the switch with large routing table so we get the TCAM error that a specific prefix cannot be programmed in TCAM memory so it will be software forwarded.%PLATFORM_UCAST-4-PREFIX: One or more, more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded
This error is quite frequent on a daily basis. My question is that will this error create a high CPU situation and affect traffic processing on the stack causing ESX Hosts to become unresponsive?
I can see drops on the 6509 Queue for interface gi1/6 , qos is disabled globaly with qos disabled all packets are in one Queue using best effort my question is if I can see drops using the sh queueing int Gi1/6 command why I am not seeing any drops when I run the Sh int (interface number ) command. [code]
View 7 Replies View RelatedI just purchased a used Catalyst 2900 XL switch and have not been succesful in connecting to the console via minicom 2.5 running on Ubuntu 12.04 or 11.10, I don’t even get junk charecters in the terminal or echo on input. The switch passes POST according to the LEDs on the front and the network ports are fucntional for switching purpouses.
I’m using a Prolific PL2303 USB-Serial adapter, which works with minicom to console into another device. I’ve tried every baud rate available and tried combonations of hardware flow control, software flow control, and niether.I’ve tested the pinout of the console cable and all pins map correctly according to Cisco spec.I’ve also tried Cutecom, putty, and screen. I have not tried HyperTerminal because I do not use windows.Is it possible that the previous owner disabled console access? Do I need to reboot the switch each time I test a different baud rate?