We have a Cisco 2911 router. We installed a EHWIC-4ESG module and configured the router based on configuration below.
ROM: System Bootstrap, Version 15.0(1r)M9, RELEASE SOFTWARE (fc1)
System image file is "flash0:c2900-universalk9-mz.SPA.151-4.M1.bin"
Cisco CISCO2911/K9 (revision 1.0) with 483328K/40960K bytes of memory.
7 Gigabit Ethernet interfaces
1 terminal line(code)
My company has an 881-w ISR that provides wireless and wired network functions for our small office (about 20 users). I was attempting to create a new V LAN (another story), and was able to create the V LAN (4) and assign it a new IP. However, when i came in today, and when i attempted to connect to the ISR, the serial console started spewing this over and over:
*Feb 8 13:31:32.479: %SYS-2-MALLOCFAIL: Memory allocation of 8 bytes failed from 0x81528DF0, alignment 0
Pool: Processor Free: 131305952 Cause: Interrupt level allocation
Alternate Pool: I/O Free: 17850656 Invalid memory action (malloc) at interrupt level -Traceback= 0x820168A0z 0x82E4
-Process= "<interrupt level>", ipl= 4 -Traceback= 0x81FF6FC8z 0x820168D0z 0x82E49944z 0x81528DF4z 0x800C3AF8z 0x800C4760z 0x810A1208z 0x810A6F8Cz 0x810BA9E0z 0x810BACBCz 0x80241A24z 0x8025ADE8z 0x8025E2F8z 0x8030ACD4z 0x804E1518z 0x80310368z
[code]....
Now, I did leave the console session up overnight, as that's the only thing that I can think of. As expected, our service contract had expired. I did reboot the ISR, and I am looking to see if this can be fixed, or symptomatic of a larger issue, and time to replace? At this point i can't even get it to stop, and thus cannot log in.
My son ran some program that he didn't know what he was doing and now there is no Network access. As far as I know this is what caused the problem, but I'm not certain. When I tried to reinstall the drivers an errors pops up stating that the drivers couldn't be installed due to "Invalid Access To Memory Location". The networking card is an Intel 82566DC-2 Gigabit Network Connection Adapter. The Networking card is part of the Motherboard. I have the original drivers but they will not install due to the "Invalid Access To Memory Location". Anyhow my son went and bought a new networking card, and it gives the exact same error. I tried uninstalling the networking card in the device manager, but when the hardware is reinstalled, and the drivers are about to install it gives the same error. computer is a Dell XPS 420 with 6 gigs of RAM, an Intel Core 2 Quad CPU Q6600@2.40GHz Also in the Device Manager everything under the Heading Network Adapters has a Yellow Triangle with an Exclamation mark in it. I know that this means that there is an error somewhere. I also want to add that when I checked the Netgear GA311 Network adapter card (this is the new card that my son bought)in the Device Manager it says This Device is not working properly because windows cannot load the drivers required for this device (code 31).
View 9 Replies View RelatedCisco 4500-X do not support egress queing on VLAN interfaces (SVI) which means cannot do a traffic-shapping, is there a work around via policing? I can police the traffic and then on the trunk interfaces do "per-port-per-VLAN" QoS but again only the policing not shapping so I was wondering what is the effect of "exceed-action transmit" command
policy-map SHAPE
class class-default
shape-average 8000000
Versus...
policy-map POLICE
class class-default
police 8000000 4000 conform-action transmit exceed-action transmit
why this static nat is invalid The following is config
ip nat pool wan xx.xx.xx.xx netmask 255.255.255.240
ip nat source static tcp 192.168.2.5 5555 xx.xx.xx.xx 5555 extendable
ip nat inside source route-map office pool wan overload
penghai#show ip nat trans
Pro Inside global Inside local Outside local Outside global
udp xx.xx.xx.xx:31 192.168.2.5:137 192.168.2.255:137 192.168.2.255:137
udp xx.xx.xx.xx:32 192.168.2.5:138 192.168.2.255:138 192.168.2.255:138
tcp xx.xx.xx.xx:3648 192.168.2.5:3648 23.11.206.176:443 23.11.206.176:443
tcp xx.xx.xx.xx:3652 192.168.2.5:3652 23.11.206.176:443 23.11.206.176:443
udp xx.xx.xx.xx:40 192.168.2.11:137 192.168.2.255:137 192.168.2.255:137
A customer wants to upgrade an IOS Base (cat4500-ipbasek9-mz.122-25.SG4.bin) of a WS-C4507R Cisco, for a IOS that have a enterprices functionalities.We install an IOS cat4500e-entservicesk9-mz.122-53.SG5.bin, but we had the following results:
config-register = 0x2102
Autobooting specified file using Variable BOOT .....
Current BOOT file is --- bootflash: cat4500e-entservicesk9-mz.122-53.SG5.bin
[Code].....
i just want to ask whether i should do some configurations or not on my cisco switch 4500 L3 regarding the error of 500 invalid port command when host try to access FTP active on to FTP server, i just did static route on gig interface with no switchport mode to that host network, all traffic type was allowed except the FTP with active mode?
View 7 Replies View RelatedI bought a cisco router last week. The reseller said it is a brand new one. However, when I try to set it with console cable connecting to PC, the default password does not work. I tried to use control+break to get access to rommon for password recovery. The tera term pro displayed nothing at all! In thin case, what should I do to setup the router? Dose the reset button in the back work to restore the router to factory setting(which means i can use default username and password)?
View 1 Replies View RelatedAccording to my boss every 3 to 4 months he has to restart our 2821 with a 16-esw module installed because of a low memory issue dealing with CEF. Here is the exact error message.
%% Low on memory; try again laterJun 8 11:18:51.777: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" Jun 8 11:19:51.823: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" %%
Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
Jun 8 11:20:51.868: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" Jun 8 11:21:51.914: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed
Today, one of our Cisco 3750 got unmanaged from NOC, we were able to ping the switch, also, traffic was flowing fine but not able to telnet or local login.On trying to login through console following messages were coming:
%% Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
[code].....
We given power on reset, after which we were able to login switch again. I wanted to know the actual reason behind it and if there is any other way to recover switch other than power reset.?
Is there a known bug for Nexus 7K version 6.0(4) related to route redistribution?I have few vlan interfaces and being redistributed to the BGP.vlan interfaces are all up ang pingable.After configuring redistribution, vlan route is not in the bgp table.sho ip bgp is saying "path invalid"
BGP routing table entry for 10.165.101.192/28, version 26302
Paths: (3 available, best #3)
Flags: (0x180c0021) on new-list, is not in urib, need resync with RIB, exported, has label
vpn: version 47719, (0x100002) on xmit-list
local label: 492294
[code]....
Most of the 4500 Switches in our network are giving the similar error for so many ports
%C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 1 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on p t Gi2/6 in vlan 100
Its impossible to do a wireshark packet tracing for all the ports.
Issue I am having with a Cisco 4507? Below is the error i am receiving.
Feb 14 10:06:09 EST: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 508 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Po10 in vlan 112
Feb 14 18:44:06 EST: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 119 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Po10 in vlan 112
Feb 15 00:51:06 EST: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 366 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Po10 in vlan 112
[Code]...
ISRG2 (c2951-universalk9-mz.SPA.152-4.M1.bin) has 512 MB of DRAM. Periodically it runs out of memory: [code]
1. Why "show process mean" command shows less memory than 512 MB? Processor Pool (248 MB) + I/O Pool (58 MB) ~ 310 MB only?
2. *Init* process holds more memory than normal (202 MB). What may cause this?
have 3 Catalyst 3750 in same stack, the IOS version is 12.2(53)SE2. Today we can not telnet/ssh to this switch, but ping is ok, and switch function is ok. I try to access the console port, it show "low on memory, try again later". After I reboot the master switch in the stack, the master switch change to another switch, then I can telnet/ssh to this switch. I check the Ciscoworks server syslog report, there are many MAC address flapping error message, and I beleive the MAC address flapping occured before several weeks. ( the G2/0/15 & G3/0/15 is connect to a VMware ESX server and the EtherChannel config mismatch with this Catalyst 3750 switch ) How to mention the root cause of the "low on memory" problem and what is the abnormal memory usage ( free memory percentage below ?% )?
View 5 Replies View Relatedi have a Ws-C3550-24-Emi switch and i need to upgrade its flash memory to 32Mb. I couldn't find any documents in cisco website about the memory upgrade guideline. Possible to upgrade this switch to 32Mb? If so, what's the max of memory i can upgrade? and the part number for this type of memory?
View 4 Replies View RelatedI have a bootflash in 4507R with the size of 60MB. I upgraded the ios from cat4500-ipbasek9-mz.122-37.SG1.bin (12.8MB Size) to cat4500-entservices-mz.122-37.SG1.bin (13.8 MB SIZE) and deleted the previous IOS.But previous IOS is still getting shown in sh bootflash: command. Furthermore, dir bootflash: commands shows there is only one IOS , which is running. How I can free the space from bootflash , as I again have to upgrade the another new IOS ( of 16MB), which I tried through solarwinds tftp and couldn't upload successfully because of its limitation. Now, If I try to upload the new IOS through FTP, it gives me memory space error. How I can free the space captured by old IOS and also how I can delete the 3rd unknown entry of IOS (shown below output of commands)?
View 4 Replies View RelatedI have a 3560 connected to an edge device and I keep etting this error. I have turned off proxy arp and turned off ip cef under the interface, however I lot connectivity to the internet when I did that. I can't seem to find any documentation on this error. I understand what it means, I just don't know how to resolve the problem.
View 3 Replies View RelatedI am noticing high memory used on my 2960-S I am running 15.0(2)SE. I am concerned that there is a problem with this model and IOS.
View 2 Replies View RelatedI have a 3560 connected to an edge device and I keep etting this error. I have turned off proxy arp and turned off ip cef under the interface, however I lot connectivity to the internet when I did that. I can't seem to find any documentation on this error. [code]
View 5 Replies View RelatedI have configured DHCP snooping on a WS-3560G-48PS running IOS 12.2(58)SE2 ipservicesk9 variant.When I enable DHCP snooping clients don't get IP addresses, when DHCP snooping is disabled, everything works fine.I have set up a SPAN port and run a capture (attached) on the traffic. Wireshark notes the Seconds elapsed field appeared to be encoded in little-endian but only on some packets. Apart from that, I can see nothing wrong with the DHCP Offer responses from my DHCP server.Attachment config.txt contains the interesting parts of the configuration. Please note g0/32 has been set to ARP inspection trust as without working DHCP snooping it would require a static bind.Is there any way of figuring out which option can't be parsed? Is there a way to force forwarding of unparsable DHCP packets while still running DHCP snooping?
View 3 Replies View RelatedI have a Switch WS-C3750E-48PD-SF with IOS 12.2(58)SE2 which reports more than 80% in utilization of memory I don't know what is causing the high memory utilization.
View 14 Replies View RelatedRecently i atsrt having problems with my cisco router 1811/k9, apparently was booting continiosly when restarted.
After i connected my console i found the problem while booting:
DDR memory test failed. Resetting the router ...
I tried to contact cisco TAC, but i need a reseller contract number to place a ticket, i do not have a resller contract number as my router was bought more than two years ago. I called cisco support and they told me to contact my reseller, my reseller told me to contact cisco so i am in a eternal loop of forwarding phone calls...
which process is consuming high memory with my c6509 switch.
View 17 Replies View RelatedI've noticed that my 6509's running VSS seem to have high I/O memory utilization.
I/O memory: Sw/Mod Bytes: Total Used %Used
1/1 8126344 7886544 97%
1/2 11796240 11442472 97%
1/5 RP 12058384 10715832 89%
1/5 SP 8388608 8104304 97%
1/7 8126344 7886544 97%
[code]....
I managed to upgrade this C2960G-48TC-L from 12.2.35-SE5 to 15.0.2-SE1 and now I can't connect anymore via telnet nor ssh. Console output simply shows
%% Low on memory; try again later
I noticed on the 2960 switches we have deployed that are running the latest IOS, 12.2(58)SE2, memory utilization is really high (almost 80 percent). I have not noticed any side effects but I wanted to verify this is acceptable. My question is does the high memory utilization matter? I see this may be related to bug CSCtw83946 but no resolution is mentioned.
I did some testing various IOS revisions and below is what I have found using a WS-C2960-48TC-L with default configuration and only my laptop connected to a switchport in vlan1. You will notice memory utilization will grows with each version but jumps drastically with 58. One difference with 58 I needed to use a different command to retrieve memory utilization. The output was gathered by pasting the output of the show command into the Cisco Output Interpreter on their website.
IOS
Show Command
Output
c2960-lanbasek9-mz.122-35.SE5.bin
show memory
[Code]....
router 2811 has 2 files ios in flash
Router#sh fla
-#- --length-- -----date/time------ path
1 35202336 Mar 3 2008 16:12:28 +00:00 c2800nm-adventerprisek9-mz.124-8d.bin
...
13 59374168 Mar 5 2012 12:49:22 +00:00 c2800nm-adventerprisek9-mz.124-24.T.bin
151076864 bytes available (105431040 bytes used)
Router#
I try to make it load c2800nm-adventerprisek9-mz.124-24.T.bin
[Code] ...........
I did
verif flash:c2800nm-adventerprisek9-mz.124-24.T.binit is ok
is it corrupted memory? how to fix it?and aslo with System image file is "flash:c2800nm-adventerprisek9-mz.124-8d.bin"it dos not show voice ports for WIC2-FXO in runn conf
I am facing high memory utilization in Cisco 2960 switch having IOS version 12.2(55)SE3.
The error we are getting is:
A "LiveHealthAlarm" event has occurred, from SwCiscoIOS device, named Switch2960. eHealth Alarm Start Time - Fri 09 Nov,2012 - 03:02:48 eHealth. Switch2960-RH-MemoryPool-Processor-Processor-1.Memory utilization high-Threshold set at 70%SPECTRUM ALARM ID|22233284 I have attached the logs also.
We are having 3750 Stack switch as our edge switch. Here we are having some issues as low memory & itermediate High CPU utilization.For memory when we checked its shwoing maximum memory is allocated to DHCPD receive & ARP Input as follows
Processor Pool Total: 70829380 Used: 56809532 Free: 14019848
I/O Pool Total: 12582912 Used: 8554920 Free: 4027992
Driver te Pool Total: 1048576 Used: 40 Free: 1048536
[code].....
i want to understand why this 2 proceses (DHCPD & ARP input) taking more memory?High CPU: We also facing intermediate high CPU utilization (above 95%). When CPU is high there were 2 processes consuming more CPU are 'Spanning Tree' (about 20%) & ARP Input (about 66%). we also checked the ARP entries, there were 1500 ARP entries & 2 incomplete ARP (out of 6000 ARP supported)
I am troubleshooting memory leaks and buffers issues on my 1900 and had some doubts regarding the problems that my router causes.Intermitently during the day for no reason the gig0/0 interface connected to ISP stops responding from our management network (log shows that the interface goes down). The ISPs modem responds fine from my management network.The issue goes away by itself in 20 minutes, sometimes more or after a hard reboot.Sometimes a router would increment a throttle value to 1. When running for 4 days without a reboot, the router raised 39 throttles and 57 input drops. [code] The router is running Version 15.1(2)T4 and I was not able to find any caveats on cisco web page (although I havent used the bug finder tool)Is this only leak I found a reason to start worrying or I can disregard it and continue basic troubleshooting (change cable and plug my ISP to another port)
View 3 Replies View RelatedI have a new cisco 3750 stack comprised of 8 members (6 x 3750G-48PS and 2 x 3750V2-48PS) running 'c3750-ipservicesk9-mz.122-58.SE2.bin'. I am seeing high memory utilisation, it seems to sit fairly stable and I do not see an increase but this has only been running a few days. No errors or performance issues. Should this be a cause for concern?
View 3 Replies View RelatedBelow memory status alerts of are seen on our syslog server for Nexus 7K switch(Default VDC).
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : CRITICAL ALERT RECOVERED
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : MINOR ALERT RECOVERED
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : SEVERE ALERT RECOVERED
Memory threshold Not created on Nexus. Can we ignore this alert or does it impact our current network traffic?
