My company has an 881-w ISR that provides wireless and wired network functions for our small office (about 20 users). I was attempting to create a new V LAN (another story), and was able to create the V LAN (4) and assign it a new IP. However, when i came in today, and when i attempted to connect to the ISR, the serial console started spewing this over and over:
Now, I did leave the console session up overnight, as that's the only thing that I can think of. As expected, our service contract had expired. I did reboot the ISR, and I am looking to see if this can be fixed, or symptomatic of a larger issue, and time to replace? At this point i can't even get it to stop, and thus cannot log in.
My son ran some program that he didn't know what he was doing and now there is no Network access. As far as I know this is what caused the problem, but I'm not certain. When I tried to reinstall the drivers an errors pops up stating that the drivers couldn't be installed due to "Invalid Access To Memory Location". The networking card is an Intel 82566DC-2 Gigabit Network Connection Adapter. The Networking card is part of the Motherboard. I have the original drivers but they will not install due to the "Invalid Access To Memory Location". Anyhow my son went and bought a new networking card, and it gives the exact same error. I tried uninstalling the networking card in the device manager, but when the hardware is reinstalled, and the drivers are about to install it gives the same error. computer is a Dell XPS 420 with 6 gigs of RAM, an Intel Core 2 Quad CPU Q6600@2.40GHz Also in the Device Manager everything under the Heading Network Adapters has a Yellow Triangle with an Exclamation mark in it. I know that this means that there is an error somewhere. I also want to add that when I checked the Netgear GA311 Network adapter card (this is the new card that my son bought)in the Device Manager it says This Device is not working properly because windows cannot load the drivers required for this device (code 31).
Cisco 4500-X do not support egress queing on VLAN interfaces (SVI) which means cannot do a traffic-shapping, is there a work around via policing? I can police the traffic and then on the trunk interfaces do "per-port-per-VLAN" QoS but again only the policing not shapping so I was wondering what is the effect of "exceed-action transmit" command
policy-map SHAPE class class-default shape-average 8000000 Versus... policy-map POLICE class class-default police 8000000 4000 conform-action transmit exceed-action transmit
I have a 6509E switch with dual 6Kw power supply that is logging "Power supply 1 input has changed. Power capacity adjusted to 2671.20W" then will bounce back to normal at random times from 1sec to 10sec. Is there a command to check what each input level of the power supply to try to identify possibly which source is causing the problem? The power supply input lights remains green while this is occuring.
I have two 3750x in a stack running c3750e-universalk9-mz.122-55.SE3.bin with License Level: ipservices?I am planning to upgrade to c3750e-universalk9-mz.122-58.SE2.bin will this keep my ipservices licence or revert back to IPbase
currenly running a C6509E, with a WS-SUP720-3B running IOS level S72033-adventerprisek9_wan-MZ.122-22.SXH3. I want to install a WS-X6748-GE-TX blade and would like NOT to have to upgrade IOS at this time. Future migrations are planned. Can this be done?
i have to Bridge the AP to VLAN1 which has the DHCP pool. For some reason when I try to do this from iOS console it tells me that gig0 is not a bridgable interface. I am newb to Cisco iOS (24 hours new ). I got the Cisco Configuration Professional working and would like to fix my issue through there if possible? why my AP wont get anything but APIPA addresses?
version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption
It never happened before and the configuration did not change. The only thing that happened, the WAN connection (point-to-point to a Cisco 3845) went down and the router rebooted while the WAN was down. When the WAN came up again, everything went fine, until about an hour later and the first occurrence of this mentioned log.This 3945 does establish an IPSec tunnel with its peer (the 3845) and all the traffic, including OSPF, is going through the tunnel.
I have an C4900M with twingig converter and SFP GLC-LX-SMD in. So the SFP supports DOM function. It is running on 12.2(53)SG2.
I would to the see the optical power level of the SFP, but it does not recognize 'show interface transceiver' command as showed in 4500 software guide.
Have a potential customer that is looking at the IE2000 series switch and at the Rockwell Allen Bradley switch
Question is does it support Device Level Ring (DLR) capability. I do not see this specifically mentioned in the Data Sheets but it talks about a Resilient Ethernet Protocol (REP) and I am wondering if this is the same thing?
A customer wants to upgrade an IOS Base (cat4500-ipbasek9-mz.122-25.SG4.bin) of a WS-C4507R Cisco, for a IOS that have a enterprices functionalities.We install an IOS cat4500e-entservicesk9-mz.122-53.SG5.bin, but we had the following results:
config-register = 0x2102 Autobooting specified file using Variable BOOT ..... Current BOOT file is --- bootflash: cat4500e-entservicesk9-mz.122-53.SG5.bin
i just want to ask whether i should do some configurations or not on my cisco switch 4500 L3 regarding the error of 500 invalid port command when host try to access FTP active on to FTP server, i just did static route on gig interface with no switchport mode to that host network, all traffic type was allowed except the FTP with active mode?
I bought a cisco router last week. The reseller said it is a brand new one. However, when I try to set it with console cable connecting to PC, the default password does not work. I tried to use control+break to get access to rommon for password recovery. The tera term pro displayed nothing at all! In thin case, what should I do to setup the router? Dose the reset button in the back work to restore the router to factory setting(which means i can use default username and password)?
According to my boss every 3 to 4 months he has to restart our 2821 with a 16-esw module installed because of a low memory issue dealing with CEF. Here is the exact error message.
%% Low on memory; try again laterJun 8 11:18:51.777: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" Jun 8 11:19:51.823: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" %%
Low on memory; try again later %% Low on memory; try again later %% Low on memory; try again later
Jun 8 11:20:51.868: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" Jun 8 11:21:51.914: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed
Today, one of our Cisco 3750 got unmanaged from NOC, we were able to ping the switch, also, traffic was flowing fine but not able to telnet or local login.On trying to login through console following messages were coming:
%% Low on memory; try again later %% Low on memory; try again later %% Low on memory; try again later %% Low on memory; try again later %% Low on memory; try again later %% Low on memory; try again later
[code].....
We given power on reset, after which we were able to login switch again. I wanted to know the actual reason behind it and if there is any other way to recover switch other than power reset.?
Is there a known bug for Nexus 7K version 6.0(4) related to route redistribution?I have few vlan interfaces and being redistributed to the BGP.vlan interfaces are all up ang pingable.After configuring redistribution, vlan route is not in the bgp table.sho ip bgp is saying "path invalid"
BGP routing table entry for 10.165.101.192/28, version 26302 Paths: (3 available, best #3) Flags: (0x180c0021) on new-list, is not in urib, need resync with RIB, exported, has label vpn: version 47719, (0x100002) on xmit-list local label: 492294
Most of the 4500 Switches in our network are giving the similar error for so many ports
%C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 1 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on p t Gi2/6 in vlan 100
Its impossible to do a wireshark packet tracing for all the ports.
Issue I am having with a Cisco 4507? Below is the error i am receiving.
Feb 14 10:06:09 EST: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 508 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Po10 in vlan 112 Feb 14 18:44:06 EST: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 119 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Po10 in vlan 112 Feb 15 00:51:06 EST: %C4K_L2MAN-6-INVALIDSOURCEADDRESSPACKET: (Suppressed 366 times)Packet received with invalid source MAC address (00:00:00:00:00:00) on port Po10 in vlan 112
have 3 Catalyst 3750 in same stack, the IOS version is 12.2(53)SE2. Today we can not telnet/ssh to this switch, but ping is ok, and switch function is ok. I try to access the console port, it show "low on memory, try again later". After I reboot the master switch in the stack, the master switch change to another switch, then I can telnet/ssh to this switch. I check the Ciscoworks server syslog report, there are many MAC address flapping error message, and I beleive the MAC address flapping occured before several weeks. ( the G2/0/15 & G3/0/15 is connect to a VMware ESX server and the EtherChannel config mismatch with this Catalyst 3750 switch ) How to mention the root cause of the "low on memory" problem and what is the abnormal memory usage ( free memory percentage below ?% )?
i have a Ws-C3550-24-Emi switch and i need to upgrade its flash memory to 32Mb. I couldn't find any documents in cisco website about the memory upgrade guideline. Possible to upgrade this switch to 32Mb? If so, what's the max of memory i can upgrade? and the part number for this type of memory?
I have a bootflash in 4507R with the size of 60MB. I upgraded the ios from cat4500-ipbasek9-mz.122-37.SG1.bin (12.8MB Size) to cat4500-entservices-mz.122-37.SG1.bin (13.8 MB SIZE) and deleted the previous IOS.But previous IOS is still getting shown in sh bootflash: command. Furthermore, dir bootflash: commands shows there is only one IOS , which is running. How I can free the space from bootflash , as I again have to upgrade the another new IOS ( of 16MB), which I tried through solarwinds tftp and couldn't upload successfully because of its limitation. Now, If I try to upload the new IOS through FTP, it gives me memory space error. How I can free the space captured by old IOS and also how I can delete the 3rd unknown entry of IOS (shown below output of commands)?
I have a 3560 connected to an edge device and I keep etting this error. I have turned off proxy arp and turned off ip cef under the interface, however I lot connectivity to the internet when I did that. I can't seem to find any documentation on this error. I understand what it means, I just don't know how to resolve the problem.
I have a 3560 connected to an edge device and I keep etting this error. I have turned off proxy arp and turned off ip cef under the interface, however I lot connectivity to the internet when I did that. I can't seem to find any documentation on this error. [code]
I have configured DHCP snooping on a WS-3560G-48PS running IOS 12.2(58)SE2 ipservicesk9 variant.When I enable DHCP snooping clients don't get IP addresses, when DHCP snooping is disabled, everything works fine.I have set up a SPAN port and run a capture (attached) on the traffic. Wireshark notes the Seconds elapsed field appeared to be encoded in little-endian but only on some packets. Apart from that, I can see nothing wrong with the DHCP Offer responses from my DHCP server.Attachment config.txt contains the interesting parts of the configuration. Please note g0/32 has been set to ARP inspection trust as without working DHCP snooping it would require a static bind.Is there any way of figuring out which option can't be parsed? Is there a way to force forwarding of unparsable DHCP packets while still running DHCP snooping?
I have a Switch WS-C3750E-48PD-SF with IOS 12.2(58)SE2 which reports more than 80% in utilization of memory I don't know what is causing the high memory utilization.
Recently i atsrt having problems with my cisco router 1811/k9, apparently was booting continiosly when restarted.
After i connected my console i found the problem while booting:
DDR memory test failed. Resetting the router ...
I tried to contact cisco TAC, but i need a reseller contract number to place a ticket, i do not have a resller contract number as my router was bought more than two years ago. I called cisco support and they told me to contact my reseller, my reseller told me to contact cisco so i am in a eternal loop of forwarding phone calls...
