Cisco Switching/Routing :: 2821 With 16-ESW CEF Low Memory
May 29, 2012
According to my boss every 3 to 4 months he has to restart our 2821 with a 16-esw module installed because of a low memory issue dealing with CEF. Here is the exact error message.
%% Low on memory; try again laterJun 8 11:18:51.777: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" Jun 8 11:19:51.823: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" %%
Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
Jun 8 11:20:51.868: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" Jun 8 11:21:51.914: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed
View 4 Replies
ADVERTISEMENT
May 28, 2012
I have a cisco 2821 router configured as a CME version 7.1. Now I want to upgrade the IOS to version 15 to get a CME version 8.6 but I faced a problem that the flash of the 2821 is 64MB and the IOS version 15 required flash 128MB. I tried to replace this flash with another 128MB installed on Cisco 2811 router but when I installed the 128MB flash on the 2821 CME the 2821 didn't boot from it.
View 5 Replies
View Related
Oct 3, 2010
We've got a cisco 2821 router which periodically stops routing all traffic. It seems to happen about once every 2 weeks, and I can't find anything that could be causing it. There are no entries in the log and the router stays up and running but requires a restart to begin processing traffic again. We're running 12.4(13r)T11.Any thoughts, or troubleshooting steps to track this down?
View 7 Replies
View Related
Mar 12, 2013
I start configuring Cisco 2821 router for multicast . First short description and attached sheme explanation. Let we say I have small network with 100 users. One router and Cisco switch 3560. Two VLAN’s, one for data another for multicast. Data from internet works fine but now I want to connect multicast servers (or source of more multicast streams) from another subnet. Router have three interfaces.I expect there should be no problems with multicast configuration, but unfortunately it is not like I expect. What I did ?
First step: enable multicast routing
Second step: on both interfaces (Fe 0/1 and Fe 0/2) - ip pim sparse-mode
Third step: configure switch that users are connected to access port in VLAN 222 (temporary to see if multicast work)
When I start VLC on computer nothing happend. If I try to connect computer on same subnet where is source of multicast streams it works fine.What I am doing wrong ? Is there anything about routing ? All subnets are directly connected. RP is not needed if I have one router or ?
View 11 Replies
View Related
Jun 25, 2012
I have just bought myself a Cisco 2821 ISR.At present in my home I have a Cisco 2621XM. Fast Ethernet 0/0 is connected to a 3524XL as a trunk to provide my LAN with inter-vlan routing. it works great. Fast Ethernet 0/1 is connected to my ISP's cable modem and uses the command "Ip address dhcp" to get an IP and all other info from my ISP.FA 0/1 is Ip nat outside and the FA 0/0 and all sub interface like 0/0.1 .24 .168 etc all ip nat inside.I get intervlan routing and access to the internet via this router.I have this 2821 to replace the 2621XM as I plan to run CME on it and want gigabit routing on my vlans as at the moment on the 2621 routing between vlans it at half duplex or seems to be.I have configured the 2821 to ip nat outside on gig 0/0 and ip nat inside on gig 0/1 and all of the sub interfaces (same setup as my 2621 but with gig ethernet)I have no access to the internet at all but I can ping www.google.co.uk and other domain names from the terminal session when I am connected to the 2821 via the console or telnet/SSH. the gig 0/0 has an IP assigned from my ISP too but no other nodes on the network can ping outside.Am I missing something here? the version of IOS is V 15.
My access list goes someting like
access-list 1 permit 10.0.0.0 0.255.255.255
access-list 1 permit 192.168.1.0 0.0.0.255
access-list 100 permit ip 10.0.0.0 0.255.255.255 any
access-list 100 permit ip 192.168.1.0 0.0.0.255 any
and so on
I still cannot access the internet.....
View 5 Replies
View Related
Nov 22, 2011
Today, one of our Cisco 3750 got unmanaged from NOC, we were able to ping the switch, also, traffic was flowing fine but not able to telnet or local login.On trying to login through console following messages were coming:
%% Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
%% Low on memory; try again later
[code].....
We given power on reset, after which we were able to login switch again. I wanted to know the actual reason behind it and if there is any other way to recover switch other than power reset.?
View 17 Replies
View Related
Jun 7, 2012
I have a Cisco 2821 Router. Its ethernet Interface(E1) is connected to an ISP's Gateway.The outside interface IP is 207.x.x.1, The ISP has given 6 public IPs (202.x.x.1- 202.x.x.6) to use in LAN.
I have configured the router`s Internal Interface(E0) with a public IP address. (i.e. 202.x.x.1)
My Internal LAN PCs are in a private range of 192.168.1.0/24 subnet. Now I wanted my PC users to access the Internet while the Routers public IP remains on internal interface. How can I do the same?
View 6 Replies
View Related
Sep 5, 2012
ISRG2 (c2951-universalk9-mz.SPA.152-4.M1.bin) has 512 MB of DRAM. Periodically it runs out of memory: [code]
1. Why "show process mean" command shows less memory than 512 MB? Processor Pool (248 MB) + I/O Pool (58 MB) ~ 310 MB only?
2. *Init* process holds more memory than normal (202 MB). What may cause this?
View 2 Replies
View Related
Jul 25, 2012
have 3 Catalyst 3750 in same stack, the IOS version is 12.2(53)SE2. Today we can not telnet/ssh to this switch, but ping is ok, and switch function is ok. I try to access the console port, it show "low on memory, try again later". After I reboot the master switch in the stack, the master switch change to another switch, then I can telnet/ssh to this switch. I check the Ciscoworks server syslog report, there are many MAC address flapping error message, and I beleive the MAC address flapping occured before several weeks. ( the G2/0/15 & G3/0/15 is connect to a VMware ESX server and the EtherChannel config mismatch with this Catalyst 3750 switch ) How to mention the root cause of the "low on memory" problem and what is the abnormal memory usage ( free memory percentage below ?% )?
View 5 Replies
View Related
Nov 3, 2011
i have a Ws-C3550-24-Emi switch and i need to upgrade its flash memory to 32Mb. I couldn't find any documents in cisco website about the memory upgrade guideline. Possible to upgrade this switch to 32Mb? If so, what's the max of memory i can upgrade? and the part number for this type of memory?
View 4 Replies
View Related
Dec 28, 2011
I have a bootflash in 4507R with the size of 60MB. I upgraded the ios from cat4500-ipbasek9-mz.122-37.SG1.bin (12.8MB Size) to cat4500-entservices-mz.122-37.SG1.bin (13.8 MB SIZE) and deleted the previous IOS.But previous IOS is still getting shown in sh bootflash: command. Furthermore, dir bootflash: commands shows there is only one IOS , which is running. How I can free the space from bootflash , as I again have to upgrade the another new IOS ( of 16MB), which I tried through solarwinds tftp and couldn't upload successfully because of its limitation. Now, If I try to upload the new IOS through FTP, it gives me memory space error. How I can free the space captured by old IOS and also how I can delete the 3rd unknown entry of IOS (shown below output of commands)?
View 4 Replies
View Related
Jul 15, 2009
I have a 3560 connected to an edge device and I keep etting this error. I have turned off proxy arp and turned off ip cef under the interface, however I lot connectivity to the internet when I did that. I can't seem to find any documentation on this error. I understand what it means, I just don't know how to resolve the problem.
View 3 Replies
View Related
Dec 9, 2012
I am noticing high memory used on my 2960-S I am running 15.0(2)SE. I am concerned that there is a problem with this model and IOS.
View 2 Replies
View Related
Jun 7, 2013
I have a 3560 connected to an edge device and I keep etting this error. I have turned off proxy arp and turned off ip cef under the interface, however I lot connectivity to the internet when I did that. I can't seem to find any documentation on this error. [code]
View 5 Replies
View Related
Dec 6, 2011
I have a 2Fe-2W Card and wanted to find out if it can be picked up and installed on a Cisco 2821? Below is the version
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(8a), RELEASE SOFTWARE (fc2)
Technical Support: [URL]
Copyright (c) 1986-2006 by Cisco Systems, Inc.
ROM: System Bootstrap, Version 12.4(1r) [hqluong 1r], RELEASE SOFTWARE (fc1)
System image file is "flash:c2800nm-adventerprisek9-mz.124-8a.bin"
View 1 Replies
View Related
Sep 6, 2012
I have a Switch WS-C3750E-48PD-SF with IOS 12.2(58)SE2 which reports more than 80% in utilization of memory I don't know what is causing the high memory utilization.
View 14 Replies
View Related
Oct 25, 2012
Recently i atsrt having problems with my cisco router 1811/k9, apparently was booting continiosly when restarted.
After i connected my console i found the problem while booting:
DDR memory test failed. Resetting the router ...
I tried to contact cisco TAC, but i need a reseller contract number to place a ticket, i do not have a resller contract number as my router was bought more than two years ago. I called cisco support and they told me to contact my reseller, my reseller told me to contact cisco so i am in a eternal loop of forwarding phone calls...
View 1 Replies
View Related
Nov 13, 2011
which process is consuming high memory with my c6509 switch.
View 17 Replies
View Related
Dec 6, 2011
I've noticed that my 6509's running VSS seem to have high I/O memory utilization.
I/O memory: Sw/Mod Bytes: Total Used %Used
1/1 8126344 7886544 97%
1/2 11796240 11442472 97%
1/5 RP 12058384 10715832 89%
1/5 SP 8388608 8104304 97%
1/7 8126344 7886544 97%
[code]....
View 5 Replies
View Related
Jan 16, 2013
I managed to upgrade this C2960G-48TC-L from 12.2.35-SE5 to 15.0.2-SE1 and now I can't connect anymore via telnet nor ssh. Console output simply shows
%% Low on memory; try again later
View 8 Replies
View Related
May 2, 2013
I noticed on the 2960 switches we have deployed that are running the latest IOS, 12.2(58)SE2, memory utilization is really high (almost 80 percent). I have not noticed any side effects but I wanted to verify this is acceptable. My question is does the high memory utilization matter? I see this may be related to bug CSCtw83946 but no resolution is mentioned.
I did some testing various IOS revisions and below is what I have found using a WS-C2960-48TC-L with default configuration and only my laptop connected to a switchport in vlan1. You will notice memory utilization will grows with each version but jumps drastically with 58. One difference with 58 I needed to use a different command to retrieve memory utilization. The output was gathered by pasting the output of the show command into the Cisco Output Interpreter on their website.
IOS
Show Command
Output
c2960-lanbasek9-mz.122-35.SE5.bin
show memory
[Code]....
View 8 Replies
View Related
Jun 25, 2012
router 2811 has 2 files ios in flash
Router#sh fla
-#- --length-- -----date/time------ path
1 35202336 Mar 3 2008 16:12:28 +00:00 c2800nm-adventerprisek9-mz.124-8d.bin
...
13 59374168 Mar 5 2012 12:49:22 +00:00 c2800nm-adventerprisek9-mz.124-24.T.bin
151076864 bytes available (105431040 bytes used)
Router#
I try to make it load c2800nm-adventerprisek9-mz.124-24.T.bin
[Code] ...........
I did
verif flash:c2800nm-adventerprisek9-mz.124-24.T.binit is ok
is it corrupted memory? how to fix it?and aslo with System image file is "flash:c2800nm-adventerprisek9-mz.124-8d.bin"it dos not show voice ports for WIC2-FXO in runn conf
View 4 Replies
View Related
May 1, 2012
We have a Cisco 2911 router. We installed a EHWIC-4ESG module and configured the router based on configuration below.
ROM: System Bootstrap, Version 15.0(1r)M9, RELEASE SOFTWARE (fc1)
System image file is "flash0:c2900-universalk9-mz.SPA.151-4.M1.bin"
Cisco CISCO2911/K9 (revision 1.0) with 483328K/40960K bytes of memory.
7 Gigabit Ethernet interfaces
1 terminal line(code)
View 3 Replies
View Related
Jan 27, 2012
I have a 5412zl 10.215.x.x/16 Most of the connections on this switch are on vlan1. B9 is the port which is connected to a Cisco 2821 Router. The port on that end is GE0/1. The port on the cisco side is not a trunk but configure with an ip of 10.215.1.30/24 Its part of a some ip access group. The network that i now sit on is a 172.x.x.x/24 (behind cisco router, about 3 hops to that main 2821)We current have a system on my side that talks to a server on the 10.215. that has no issues. I'm trying to access some switches on the 10.215. and have had no luck reaching them.
Here is the access list that i found that port is configured to use:
permit ip 10.215.0.0 0.0.255.255 172.18.0.0 0.0.255.255 permit ip 10.254.0.0 0.0.255.255 172.18.0.0 0.0.255.255 permit ip 10.215.0.0 0.0.255.255 172.14.0.0 0.0.255.255 permit ip 10.254.0.0 0.0.255.255 172.14.0.0 0.0.255.255 permit ip 10.215.0.0 0.0.255.255 192.168.2.0 0.0.0.255 permit ip 10.254.0.0 0.0.255.255 192.168.2.0 0.0.0.255 permit ip 10.215.0.0 0.0.255.255 192.168.20.0 0.0.0.255 permit ip 10.254.0.0 0.0.255.255 192.168.20.0 0.0.0.255 I would think the first permit would allow me to get through to the 10.215 side but maybe i need to set something up on the hp size to let it know how to get back? I'm very new to this stuff.
View 3 Replies
View Related
Jul 31, 2012
I have 2821 router configured with two subinterfaces. This router is connected on cisco 2960 switch. The trunk on 2960 is configured without any prunning of vlans. I noticed that udp broadcast traffic is being forwarded through my router on native vlan 1 (this interaface do not have ip address configured). Below is configuration:
Router:
interface GigabitEthernet0/0
no ip address
duplex auto
[Code]....
View 6 Replies
View Related
Jul 2, 2012
Currently I have a network that looks like this:
ASA5510 - - - Internet - - - ASA5510
| |
EIGRP EIGRP
| |
2821 -----------MPLS----------1841
BGP
The MPLS connection is currently down, I'm trying to run a failover Site-to-Site VPN over the internet. All of the examples I've read have both connections involved in the failover coming out of one device. Since I'm not working that way, what is going to be the best way to failover? Do I need to set up some sort of IP SLA in the config? Or can I somehow weight routes in EIGRP in a way that the connection will failover from Internet to MPLS when the MPLS goes down and vice versa when the MPLS connection comes back up?
View 2 Replies
View Related
Mar 10, 2013
What is the maximum VPN Clients that could be connected to cisco router 2821, with this IOS c2800nm-adventerprisek9-mz.124-20.T.bin
View 3 Replies
View Related
Nov 9, 2012
I am facing high memory utilization in Cisco 2960 switch having IOS version 12.2(55)SE3.
The error we are getting is:
A "LiveHealthAlarm" event has occurred, from SwCiscoIOS device, named Switch2960. eHealth Alarm Start Time - Fri 09 Nov,2012 - 03:02:48 eHealth. Switch2960-RH-MemoryPool-Processor-Processor-1.Memory utilization high-Threshold set at 70%SPECTRUM ALARM ID|22233284 I have attached the logs also.
View 3 Replies
View Related
Dec 26, 2012
We are having 3750 Stack switch as our edge switch. Here we are having some issues as low memory & itermediate High CPU utilization.For memory when we checked its shwoing maximum memory is allocated to DHCPD receive & ARP Input as follows
Processor Pool Total: 70829380 Used: 56809532 Free: 14019848
I/O Pool Total: 12582912 Used: 8554920 Free: 4027992
Driver te Pool Total: 1048576 Used: 40 Free: 1048536
[code].....
i want to understand why this 2 proceses (DHCPD & ARP input) taking more memory?High CPU: We also facing intermediate high CPU utilization (above 95%). When CPU is high there were 2 processes consuming more CPU are 'Spanning Tree' (about 20%) & ARP Input (about 66%). we also checked the ARP entries, there were 1500 ARP entries & 2 incomplete ARP (out of 6000 ARP supported)
View 6 Replies
View Related
Apr 24, 2013
I am troubleshooting memory leaks and buffers issues on my 1900 and had some doubts regarding the problems that my router causes.Intermitently during the day for no reason the gig0/0 interface connected to ISP stops responding from our management network (log shows that the interface goes down). The ISPs modem responds fine from my management network.The issue goes away by itself in 20 minutes, sometimes more or after a hard reboot.Sometimes a router would increment a throttle value to 1. When running for 4 days without a reboot, the router raised 39 throttles and 57 input drops. [code] The router is running Version 15.1(2)T4 and I was not able to find any caveats on cisco web page (although I havent used the bug finder tool)Is this only leak I found a reason to start worrying or I can disregard it and continue basic troubleshooting (change cable and plug my ISP to another port)
View 3 Replies
View Related
Jan 21, 2012
I have a new cisco 3750 stack comprised of 8 members (6 x 3750G-48PS and 2 x 3750V2-48PS) running 'c3750-ipservicesk9-mz.122-58.SE2.bin'. I am seeing high memory utilisation, it seems to sit fairly stable and I do not see an increase but this has only been running a few days. No errors or performance issues. Should this be a cause for concern?
View 3 Replies
View Related
Mar 22, 2012
Below memory status alerts of are seen on our syslog server for Nexus 7K switch(Default VDC).
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : CRITICAL ALERT RECOVERED
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : MINOR ALERT RECOVERED
PLATFORM-2-MEMORY_ALERT_RECOVERED: Memory Status Alert : SEVERE ALERT RECOVERED
Memory threshold Not created on Nexus. Can we ignore this alert or does it impact our current network traffic?
View 5 Replies
View Related
Jun 11, 2013
We had a stack of 4 qty 3750g running IP base on ver 12.2.32, then installed a 3750x to the stack and upgraded the whole stack to 15.0.2 SE3. In doing so, we noticed that the memory utilization jumped from 60-70% to 83-84%.
We had the same issue occur when upgrading to 15.0.2 SE3 on another stack that was 6 qty 3750g running ip-services, but this one jumped to 90%. On the 6 qty stack, we downgraded to 12.2.55 and the memory util went back down to 60-70%.
On the mixed stack, we replaced the 3750x with another 3750g and downgraded the whole stack to 12.2.55, however, the memory utilization did not drop down. As far as I can tell, no config changes have changed from the original IOS.
View 4 Replies
View Related