Cisco WAN :: Using 3G HWIC On ASR1000
Jun 24, 2012I am looking for a way to use a 3G connexion on ASR1000.Is it possible to install HWIC module of ISR2 in SPA slot or use an USB modem on the RP?
View 2 Replies
ADVERTISEMENT
Cisco WAN :: SPA To Use For ATM DS3 On ASR1000 Routers
Jul 9, 2011Am trying to find out what is the suitable SPA for ASR1000 routers to connect ATM DS3 through the local telco. Currently this is connected to a NM-ATM-DS3 module on a C3845 router. The reason for asking is we need to upgrade the WAN router to ASR1000.
View 2 Replies View RelatedCisco WAN :: Hot-swap On ASR1000?
Sep 25, 2012The ASR1000 router supports hot-swap modules and network interfaces?
View 1 Replies View RelatedCisco WAN :: IPv6 ISG On ASR1000
May 5, 2013We use ISG on asr1000 (l3 routed subscriber). Now we are trying to implement ipv6 isg sessions. so.. for ipv4 sessions we have
radius-server attribute 8 include-in-access-req
radius-server attribute 32 include-in-access-req but for ipv6 there is no such attribute#radius-server attribute ?
11 Filter-Id attribute configuration
188 Num-In-Multilink attribute configuration
218 Address-Pool attribute
25 Class attribute
30 DNIS attribute
31 Calling Station ID
32 NAS-Identifier attribute
4 NAS IP address attribute
44 Acct-Session-Id attribute
55 Event-Timestamp attribute
6 Service-Type attribute
60 CHAP-Challenge attribute
61 NAS-Port-Type attribute configuration
66 Tunnel-Client-Endpoint attribute
67 Tunnel-Server-Endpoint attribute
69 Tunnel-Password attribute
77 Connect-Info attribute
8 Framed IP address attribute
95 NAS IPv6 address attribute
list List of Attribute Types
nas-port NAS-Port attribute configuration
nas-port-id Nas-Port-Id attribute configuration
what is best practice for authorize ipv6 l3 subscribers ?
Cisco WAN :: ASR1000 Evc On Portchannel
Apr 11, 2013We have asr1006 with 2 esp-40 and 2 rp2 and 2 sip-40. we need to bridge vlan from portchannel (2*10) to single 10ge port.
So fn said that EVC on Port-Channel supported on our software and document [URL] have such example
- configure terminal
- interface port-channel channel-group
- service instance id ethernet
But on our router we have not service command on port-channel. only on non portchannel interface.
But other document have Restrictions for Configuring EVCs on the Cisco ASR 1000 Series Router The following features are not supported: EVC on Etherchannels
Connect ww port-channel 1 2 tenGigabitEthernet 0/1/0 2 this is possible command on our router (but i can't create service instance on portchannel interface)
We need to bridge l2 without l3 termination ? is this possible with port-channel ?
Cisco :: ASR1000 CUBE SP Log Messages
Dec 6, 2012we're trying to integrate our SBC instances (CUBE SP on ASR1000) into our network management system (EMC SMARTS)Syslog messages from SBC instances are some kind of cumbersome with lot of line breaks resulting in multiple syslog messages the NMS must parse.How do I configure it to just put it all into one line just as "normal" log messages?
View 2 Replies View RelatedCisco :: ASR1000 Monitoring NAT Using Netflow 9
Feb 7, 2010I have a question regarding netflow and NAT. I have read some documentation (on ASR1000) regarding monitoring NAT process on Cisco ASR1000 that can be done using netflow version 9 (the term was called netflow event logging a.k.a NEL). The problem is, I have not found the netflow collector that can do that. I have queried several software such as manage engine "Netflow Analyzer" and Lancope, but they said their software can not do that.
View 11 Replies View RelatedCisco WAN :: How To Test Aaa Authentication On ASR1000
Dec 15, 2012How to test the aaa on cisco asr 1000 ? I wana test some user account to a cisco acs.
View 5 Replies View RelatedCisco WAN :: Embedded Packet Capture On ASR1000
Oct 30, 2012I'm trying to use EPC on ASR1001 running IOS-XE 3.4, and it won't work. Configuration commands are accepted by the router, but there are no packets in the capture buffer.In release notes for IOS-XE, in the 2.5 section, there is a statement that EPC is not supported on ASR1k. Is it true also for newer versions of IOS-XR?
View 1 Replies View RelatedCisco WAN :: ASR1000 Will It Still Possible To Run VPLS Over Dark Fiber
Jul 7, 2012One of our customer would like to connect 3 datacentres and decided to use VPLS to extend layer 2 VLANs . For this purpose they have bought six Cisco ASR1000 edge routers( two at each side).They also wanted to buy MPLS SP backbone but have decided to buy 2x10G dark fibre links instead.My question is,
1-Will it still possible to run VPLS over dark fibre? Because all the documents I read regarding VPLS are deployed over MPLS backbone.
2-Any sample configuration for implementation VPLS in ASR1000 ?
Cisco WAN :: Gigabit Ethernet Ports On ASR1000?
Mar 6, 2013how the ASR1000s are being setup.I am looking at ASR1000s as part of network refresh and was looking at RJ-45 based Gigabit Ethernet ports compatible with the ASR1000s SPA-5X1GE-V2 seems to be an option but they are all SFPs. Are there any options for RJ-45 ones on ASR1000s?
There is an option for the 2 port where one can mix and match SFPs and RJ45 but I was looking for something which is RJ45 only.Are there any options for them available.I know I could get something with FastEthernet type but was looking for the GigabitEthernet type.
Cisco WAN :: ASR1000 Multi-link PPPoE With LFI
Mar 26, 2013I'm trying to find out what platforms support Multilink PPP with Link Fragmentation and Interleaving over a single link, when that single link is PPPoE. In searching the documentation, the best information I can find is that it seems to be supported in one direction on the ASR1000 url...Many platforms appear to support PPPoE and also MLPPP w/LFI, but it's not clear that both features are supported on the same link.
The application is a radio that has an Ethernet interface on its terrestrial link, and acts as an Ethernet bridge. Would like to use Multilink PPPoE with LFI in order to provide LFI in order to run VoIP over lower speed links (e.g 256kb). For what it's worth, the radio also supports RFC 5578 PPPoE Extensions for Credit Flow and Link Metrics. It was fairly easy to find what platforms support RFC 5578. But RFC 5578 would be used to support variation in the capacity of the link. If the link speed is fixed, RFC 5578 is not needed. I was trying to find if the set of platforms supported increase if the need for RFC 5578 is taken off the table.
In particular, I'd be interested in the whether the ASR 9000 series supports MLPPP bundles with LFI when the links are PPPoE.
Cisco WAN :: Difference Between HWIC-1ADSL-M And HWIC-1ADSL?
Jun 12, 2013What is the difference between HWIC-1ADSL-M and HWIC-1ADSL without the "-M"?Can either of the above ADSL cards be used in Cisco 3845 router? We are using HWIC-1ADSL-M in our Cisco 3845 routers everywhere?
View 1 Replies View RelatedCisco WAN :: ASR1000 - Encryption Over Metropolitan Optical Ethernet
Mar 1, 2012We're installing ASR1000 series (ASR1001 and ASR1006) routers on a new WAN and have a requirement to enrypt the traffic between the EIGRP neighbors. Each ASR will be connected to the MOE with a gig interface and we will be using L3 on the interfaces with EIGRP as the routing protocol. We have advipservices-k9 IOS-XE
The ASR1006 is our datacenter WAN router and all remote sites have the ASR1001s. The ASR1006 WAN interface will be configured with L3 subinterfaces, one to each remote location, using a /30 mask.
What is the best method to encrypt the traffic between the ASR1006 WAN interface and the remote ASR1001 WAN interface?
Cisco Infrastructure :: Show Platform Hardware Capacity On ASR1000?
Sep 11, 2011Any equivalent show command to get the "FIB TCAM Usage" on An ASR 1006 ?the "show platform hardware capacity forwarding" does not work on ASR1006 Example on 6500: Router# show platform hardware capacity forwarding.
View 1 Replies View RelatedCisco WAN :: ASR1000 MLS QoS Trust DSCP Under Router Platform Interface
Feb 13, 2013I want to know what the default behavior about the command 'mls qos trust dscp' under router platform interface. the router is ASR1000 series.we don't need to put above command line to trust dscp in case of router? otherwise, we have to add it as welll as like switch platform.
View 4 Replies View RelatedCisco WAN :: ASR1000 Router Supports Hot-swap Modules And Network Interfaces?
Sep 25, 2012The ASR1000 router supports hot-swap modules and network interfaces?
View 2 Replies View RelatedCisco Switching/Routing :: How To Perform UBRL User Based Rate Limiting On ASR1000
Mar 27, 2012how to perform UBRL User Based Rate Limiting on ASR1000 like we can do it on Catalyst6500?
View 3 Replies View RelatedCisco Switching/Routing :: ASR1000 - Dual ISP Active / Active Connection On Single Router
Jun 10, 2012I am working on a network which has two ISP connections (Active/Active) terminating on router (ASR1000). From the LAN side (6500 switch) all the traffic need to be route on ISP1 but some of the specific subnets like 10.250.0.0/16 need to be route on ISP2 connection.
I am planning to use PBR and NAT with route maps. any documents or refrences are provided.
(access switches)---------(core switch)----------(routers)----------------(ISP1)
----------------------(ISP2)
Cisco WAN :: To Add HWIC-2FE With 2821
Mar 27, 2013I have an existing C2821 router (2 onboard GE + 1 HWIC-2FE) currently. Like to add another 1 HWIC-2FE. Saw this doc on Cisco website which states Max of 2 HWIC-2FE for Cisco2821. Want to confirm this is indeed so as another link states max of 1 HWIC-2FE.
View 3 Replies View RelatedCisco WAN :: Can SM-ES3-16-P Used In Place Of HWIC-2FE
Apr 4, 2013I want a low cost solution router with 16 10/100 routed ports...The idea is to club 16 different segments on ofc to this router via media convertor and there will be dynamic protocols such as EIGRP or higher running between these segments.
The router needs to be security enabled...the equipments needs to be a router by defination (not a layer 3 switch)..As per my understanding there is limitation on number of HWIC-2 FE that can be put in ISR G2 series due to which I cannot reach that figure...
Kindly let me know if i can use SM-ES3-16-P in the place of HWIC-2FE for this kind of requirement.
Cisco WAN :: HWIC-2FE Module In ASR-1000?
Nov 15, 2011Does the ASR-1000 accept an HWIC module, or must one go to a SIP/SPA for all modules?
View 1 Replies View RelatedCisco WAN :: HWIC Card For 1861?
Dec 5, 2011if the card HWIC-1SER is the equivalent card HWIC-1T for 1861 router?
View 3 Replies View RelatedCisco WAN :: 3845 HWIC-2FE Is Not Detected
Oct 3, 2009I have cisco 3845 router with 4 HWIC-2FE card none of them is detected the message displayed is [code]
View 7 Replies View RelatedCisco :: Configuring HWIC-16A For Terminal Service?
Mar 26, 2013I just added an HWIC-16A to a Cisco 2911 router for use as a Terminal Server.[URL]I've installed and configured the card properly. However, I receive the following error message:Attempt from Cisco CLI
View 2 Replies View RelatedCisco WAN :: 2811 - Adding A HWIC In Router
Jun 12, 2011I have a Cisco 2811 router with c2800nm-adventerprisek9_sna-mz.124-2.T6.bin as IOS and i wsh to install this HWIC 4port to increase available ports on my router. Wish to know if this is going to work,that is, if i installed it the IOS available will recognise this card
View 4 Replies View RelatedCisco WAN :: 3925 Cannot Swap Hwic Without Reload
Dec 20, 2012I have cisco router 3925 and i add install HWIC-4ESW, as i sew on cisco documents you can hot swap the hwic without reload the router but i it's not working at all. How to do it ?
View 1 Replies View RelatedCisco WAN :: 1841 With 3G HWIC - Backup WAN Connection?
Jul 3, 2011I'm trying to backup my primary WAN with secondary backup connection - 3G WAN through Cellular 0/0/0.Point is that I need to track some external IP address on my primary interface, for examle 8.8.8.8. If it is not reacheable, then router brings up backup connection - 3G. This can be done by using dialer-watcher.Simple.But unfortunately my primary WAN interface is an FastEthernet, which is the coonected to a switch, switch to WAN . There is no dialer-watch commands on it. Thats sad .
One more time :
WAN -> SWITCH -> ROUTER(WITH 3G HWIC and Fa 0/0 connected to switch).
Cisco WAN :: HWIC-2SHDSL Disconnection With ATM Interface
Jul 13, 2011I have a scenario where multiple branches are connected to Head Office via DSL links. The branches are located in differenct exchanges, everyone once in a while ALL branches go down at the exact same time except 3 branches and those 3 branches don't have ATM interface on the router, rather they have external DSL modem, all other branches that face the disconnection (for couple of minutes) have either HWIC-1ADSL-M or HWIC-2SHDSL and the DSL line is directly plugged into the card. [code]
I tried so many solutions like adding "operating-mode auto" command under the subinterface, IOS upgrade, changed dynamic routing protocol from EIGRP to OSPF... Nothing worked, on the logs of the router it just shows "EIGRP neighbor down", at the time of the problem I can't ping any of the affected branches on their WAN ATM interface although it stays physically "up up".Could the problem be a missing command that I need to add under the subinterface? Something maybe related to clocking or timeout or..?Note that hte problem occurs randomly, every few days, sometimes every 10 days, and all branches with ATM interface go down at the exact same time.
Cisco WAN :: 33945 Ospf Not Forming Over Hwic
Feb 12, 2013I' ve come across an weird ospf issue between my router connected via layer 2 service provider link, details as below.We have a base station router for satelite termination at service provider end connected via Layer 2 vlan link to a head end C3945, current interface for head end is a layer 2 vlan and layer 3 ip address lives under sub interface, config as below
-Head End router
-Cisco 33945
Cisco WAN :: Hwic-4ESW 2 Unit On Chassis?
Mar 18, 2012i have some issue with Hwic-4ESW, if i install one card(Hwich-4ESW) is working all port then i install one more card ( Hwic-4ESW) it not working.interface and vlan is up but from my PC to port Hwic-4esw not working. what is problem on this ?
View 9 Replies View RelatedCisco WAN :: Install HWIC-1GE-SFP On 3845 Router
Jul 25, 2012In our Environmet we have 3845 Edge Router Current Ios Version is Version 12.4(1a),(c3845-advipservicesk9-mz.124-1a.bin)As management got another fiber leased line(Single Mode) for which i have install SFP slot part number HWIC-1GE-SFP,after installation of HWIC-1GE-SFP in router the follwing slot is showing
GigabitEthernet0/1/0
%HWIC_1GE_SFP-6-SFP_IN: Interface GigabitEthernet0/1/0 1000BaseLX SFP has been inserted
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/1/0 xx.xx.xx.xx. YES manual up down
for testing purpose i tried the same procedure into the switch and its working fine where as in Router the link is not coming up ,
Cisco WAN :: Number Of EHWIC / HWIC In 2911?
Oct 6, 2011According to specifications fo Cisco ISR G2 2911, it has got 4 EHWIC slots. But in [URL] appears that Cisco2911 supports only 2 HWIC-2FE or only 2 EHWIC-1GE-SFP-CU.
View 1 Replies View Related