Cisco WAN :: Gigabit Ethernet Ports On ASR1000?
Mar 6, 2013
how the ASR1000s are being setup.I am looking at ASR1000s as part of network refresh and was looking at RJ-45 based Gigabit Ethernet ports compatible with the ASR1000s SPA-5X1GE-V2 seems to be an option but they are all SFPs. Are there any options for RJ-45 ones on ASR1000s?
There is an option for the 2 port where one can mix and match SFPs and RJ45 but I was looking for something which is RJ45 only.Are there any options for them available.I know I could get something with FastEthernet type but was looking for the GigabitEthernet type.
View 4 Replies
ADVERTISEMENT
Aug 11, 2011
I was wondering if I could use the CISCO3945 Integrated Gigabit Ethernet WAN ports for routing, I need to enable BGP and I was willing to use one of those ports.
View 2 Replies
View Related
Sep 26, 2012
I have an Ethernet Loopback Plug (4 Pairs) made and trying to test the Gigabit Interface on a 3845 Router with a fail result. The interface will show up/up only if I set the interface to 100M/Full Duplex when I plug-in the Ethernet Loopback Plug (4 Pairs). I don't see this Gigabit Interface @ 3845 router has any option to set it to internal or external loopback.
View 2 Replies
View Related
Mar 1, 2012
We're installing ASR1000 series (ASR1001 and ASR1006) routers on a new WAN and have a requirement to enrypt the traffic between the EIGRP neighbors. Each ASR will be connected to the MOE with a gig interface and we will be using L3 on the interfaces with EIGRP as the routing protocol. We have advipservices-k9 IOS-XE
The ASR1006 is our datacenter WAN router and all remote sites have the ASR1001s. The ASR1006 WAN interface will be configured with L3 subinterfaces, one to each remote location, using a /30 mask.
What is the best method to encrypt the traffic between the ASR1006 WAN interface and the remote ASR1001 WAN interface?
View 2 Replies
View Related
Aug 8, 2012
I am having a problem with my Realtek RTL8168D/8111D PCI-E Gigabit Ethernet NIC. It is not detecting my ethernet cable, and thus leaving me without internet on my desktop, after i updated its driver. The cable is not the problem as I have tested the cable with my laptop. I tried rolling back drivers, doing system restore and removing drivers with driversweeper and letting windows install the drivers again. However, none of these worked for me. I doubt the NIC is faulty as it was working before i updated the drivers. I am using windows 7 home premium 64-bit.
View 9 Replies
View Related
Jun 9, 2013
We have an ASA 5505. 5505 comes with two default vlans 1&2 with each of them marked as inside & outside respectively.My query is , if i do not want to use vlans on 5505 and only want to use the Ethernet ports as pure physical layer 3 ports, is it possible?i.e. i want to assign a layer 3 ip address on eth0/0 and eth0/1 and make them as the inside & outside interfaces rather than vlans. is it possible to do away with vlans in 5505 & will it work otherwise?
View 3 Replies
View Related
Jul 30, 2010
The problem I have run into is that I am not getting any connectivity between my two gigabit ports on the 1941. I have ge0/0 setup as my internal network and is running dhcp, ge0/1 is the connection to the modem. I can't figure out how to configure the connections so my internal traffic on ge0/0 routes out through ge0/1.
Here is my config:
Using 4312 out of 262136 bytes
!
[Code].....
View 8 Replies
View Related
Apr 18, 2012
I am trying to test the gigabit ports on a Cisco 2950 switch. 1000Base-SX. I have the internet or dhcp server connected to port 24 on the first switch and my pc hooked up to the (any) port on the second switch. Both switchs are connected with a fiberoptic cable with MTRJ connectors on either side.
Now when I use gi0/2 on both switchs all works fine. I get a dhcp address from the router on the other end of the first switch. but when ever I include gi0/1 on either end of the fiber optic cable neither of the ports will initialize (neither of the leds above the ports light up). I have deleted all the config files before booting up the switchs so they should have a default blank configuration.
When looking at the Http web page for the switch I dont see any issues with the port. what can I do to make sure these ports are working or can be configured?
I will not be able to post back any more information about the switch until next tuesday. Im off till then.
View 5 Replies
View Related
Jun 4, 2012
Are all ports on Catalyst 4500X Gigabit/10-Gigabit or just the ports on 8-port module. We are looking at 4500X for campus distribution layer but need Gig ports to access switches for now and may year from now will be using 10G.
View 7 Replies
View Related
May 1, 2013
I have two switches, WS-3750-24PS-S connected in two cabs via fiber. Patch panels at both ends with patch leads. Used tester to confirm end to end fiber connectivity. When plugged in, one switch lights up the other does nothing.
Ports are as follows:
interface GigabitEthernet1/0/2
switchport trunk encapsulation dot1q
switchport mode trunk
same at both ends. Tried both GI ports same result. swapped transceivers over and the same result, (one switch lit one not - the same switch in both cases). put both transceiver in each switch, (gi0/1-0/2 in a single switch). on the one that lights up in the original scenario we get link on both ports and they come up, on the other nothing happens. shut down both ports on the malfunctioning switch and no shut them, no change.
Show transceivers doesn't show transceivers on the malfunctioning switch, and no attempt is made to bring the ports up if the fiber is removed and replaced.
it is almost as though the two gb ports are kaput. Anything else I can try?
View 12 Replies
View Related
Jun 13, 2012
My router is on a static IP, it is a Linksys WRT150N, and it doesn't have gigabit ports. Is it possible to run it through the 1522's gigabit ports.Modem -> 1522 -> actual router.
View 2 Replies
View Related
Aug 15, 2012
how many Gigabit port will be supported by Cisco 7206VXR with G1 engine model. By deault we hot 3 GE, is it possible to add additional Gigabit ports with the existing hardware.
View 3 Replies
View Related
Jan 24, 2012
Adding ports to my Fairpoint provided Westell 7500 Rev D DLS modem router which has only 4 RJ45 ports. Bought a Linksys SE2500 gigabit smart switch but it doesn't assign IP or pass on router assigned IPs. Can't get ASSISTANCE from Fairpoint [successor to Verizon] configuring router or any advice on other ways to get more wired devices on LAN.For speed in backups I'd like 3 devices to be able to communicate at giabit speed Want to have an NAS and 2 Win7 Ultimate computers on smart switch, 3 other wired devices [WinXP, AT&T Cell tower, & DirectTV whole house SWM interface] and wireless on the router. 1. Are Fairpoint specs for DSL published so I could get another DSL modem router instead of the Westell or is it better to configure Westell as a router only and use a new to be acquired router with or without the existing or a new gigabit switch. I have a DI-624 from the pre-DSL Hughesnet satellite days.2. Are there less smart switches which would work better and let router assign the IPs?3. If this is too complex for me, can you recommend a remote access consultant to walk me through this for a fee?4. I'm 82, have been in computing since 1960, mainly in on-line end user environment mbut don't know the bridging, PPP PPoE differences, and implementation or configuration details of current hard and software except as a user.
View 2 Replies
View Related
Feb 17, 2011
I just upgraded to an E4200 from a D-Link DIR-655. I cannot seem to get my desktop to connect to the E4200 at 1 GBS. My adapter is set to "auto negotiate" but will only connect at 100 MBS. If I try forcing the adapter setting to 1 GBS, it never connects. I can swap out my E4200 with the DIR-655 and it will connect at 1 GBS just fine. I am using a CAT 5E cable. Is there something I'm missing here or is the E4200 just more finicky than the the DIR-655?
View 9 Replies
View Related
Jan 19, 2012
Have the issue of connecting a pc an NAS to a E4200 and when transferring from pc to NAS, only getting < 10 mbps transfer rates? NAS is Dlink 321. PC has Gigabit ethernet card. cables are cat 6. Even when I force the NAS and pc network card speeds to 1.0 GBps full duplex, I only transfer files at < 10 Mbps.
View 3 Replies
View Related
Aug 14, 2011
i have a cisco 1921 router and it has ge0/0 (LAN) and ge(0/1) WAN. ge 0/0 is well connected and i can ping it and the LED light is on but ge 0/1 has failed to come up.Ge0/1 is connected to an IDU and has a public IP address. The LED light also does not light on ge 0/1.Where could the problem be?
View 5 Replies
View Related
Sep 24, 2011
Is there a PCI Express 2.0 Gigabit ethernet card [NIC] which i can install in this motherboard where usually one installs NVIDIA graphic cards?
View 4 Replies
View Related
Oct 7, 2011
I currently have 2 PCs that are directly connected to each other via a 1Gbs Cat6 connection.I don't currently have a 1Gbs router so what I am doing right now is unhooking this connection and reconnecting both machines to my router when I need internet access. I have ordered some USB Wi-Fi adapters so I can have both machines access the internet that way whilst still use FTP between them on the 1Gbs line.If I were to scrap that idea and get a 1Gbs hub, connect both PCs straight into that, and then also connect the hub to my 100mbits router, would the 2 computers be able to communicate with each other at 1Gbs and then talk to the router at 100mbits, or would the whole network run at 100mbits.I don't really want to have to shell out on a 1Gbs router as I don't need anything else on the network to run at that speed.
View 6 Replies
View Related
Dec 15, 2011
Purchased and configured 2951 router based on Telco specs that required T3/DS3 card with coax connection for MPLS. When telco showed up to install DS3 they handed me a UTP copper connection.... Can I use one of the Gigabit ethernet connections on the 2951 as my MPLS interface into the provider's cloud?
View 2 Replies
View Related
Mar 15, 2012
We have a Cisco 7206 VXR Router with NPE-G2. As everybody aware that, It has got 3 x Gigabit Ethernet Ports on this. We would like to add Two more Copper Gigabit Ethernet Interfaces. The Configurator does not show any options to add that.Now we have a doubt that, Does this 7206 VXR support how many Copper Gigabit Ethernet Interface ?. There is no clear answer available in the Data Sheets.
View 2 Replies
View Related
Aug 17, 2011
We have a Cisco 7206 VXR Router with NPE-G2. As everybody aware that, It has got 3 x Gigabit Ethernet Ports on this. We would like to add Two more Copper Gigabit Ethernet Interfaces. The Configurator does not show any options to add that...
Now we have a doubt that, Does this 7206 VXR support how many Copper Gigabit Ethernet Interface ?. There is no clear answer available in the Data Sheets.
View 6 Replies
View Related
Apr 10, 2012
I'm going to be upgrading my network (router and network cards etc). I was wondering if there will be any performance difference with the Belkin Fastcat 5e I currently have and CAT6 cables?
View 7 Replies
View Related
Jan 30, 2012
I have a Dell Studio running windows 7 sp1. yesterday i was on the internet as normal. Today i was able to connect via my schools wifi, but not my ethernet cable. Device manager shows that my ethernet port should be available.
View 3 Replies
View Related
Jan 7, 2011
So my old router needed replacement and my dad bought a Netgear gigabit ethernet switch instead of a router. It said that it gets 1Gbps when I look inside the local area connection speed. The problem was we tried to use it like a router but only 2 computers could connect to the internet at one time but it was indeed noticeably faster when it came to video streaming speed. We since returned it and bought a Netgear N600 router that says the speed is 300mbps but like my old router it shows the speed is actually 100mbps and the streaming is good for the most part but every now and then slows down. Would using the ethernet switch with our new router work with streaming speeds and connection stability and of course let more computers connect and also use the routers wireless.
View 13 Replies
View Related
Dec 17, 2012
I have the following problem. I bought two TP-LINK TG-3269 gigabit cards, placed them in two computers and connected them directly. On my Ubuntu system I used iperf tool and measured only 95 Mbit/s. It wont go any faster, I tried many times with different settings.
The indicator lamp shows 1000 Mbit/s.
View 5 Replies
View Related
Feb 1, 2012
But I currently have a Linksys E3200 I bought in a moment of weakness after an evening of being pissed off at bricking my old WRT610N. (soft bricked, but I'm beyond screwing with it)
There's nothing *wrong* with it, but I am interested in something that either comes preinstalled with DD-WRT, or is well supported (ie easy to install on) by DD-WRT. I plan on selling the E3200 once I find something to replace it.
My requirements:
-Gigabit
-5 GHz (I have a file server/HTPC; I don't want to be limited to gigabit ethernet)
-$150 or less (I know $150 is high, but I figure I'll get close to that for the E3200)
View 4 Replies
View Related
Mar 30, 2011
I am moving into an apartment thereafter. I have an HTPC in use, a personal computer for gaming/processing, and my fiancee has an Apple Macbook Pro that she uses quite often. I have an HDHomeRun Dual (2 tuners) for streaming OTA/QSM cable over the network (the HDHomeRun plugs into the network, not a computer). I also have a TV and Blu-Ray player that have ethernet ports.
Currently I use Verizon Fios and their Actiontec MI424WR router, which to my knowledge has gigabet ethernet. When I move I will probably be saddled with Comcast Xfinity Internet, which will supply a cable modem if I want, but no router. The only router I currently own is a Zyxel NBG-419N, which has only 100/10 ethernet ports. My current computers all have gigabit ethernet. For the home theatre components and my HTPC, I plan to pick up a network switch with gigabit ethernet. So my questions are:
1. If I use the Zyxel and the Comcast cable modem, would I be throttling my network speed at the router? I would hate to choke my speed just because one component does not have gigabit ethernet.
2. If I were to upgrade to, say, an Asus RT-N56U, would that make a huge difference on network browsing and throughput speeds?
3. Finally, what kind of cable is needed to maximize discernible speed increase? Cat5, Cat5e, or Cat6?
View 3 Replies
View Related
Jan 27, 2012
I use one cisco 6506-e switch with modules (including two sup720-3B,one 6148-GE-TX,one 6724-SFP), and Thomson ViSE EM1000 encoder connect to 6148-GE-TX module with its two Gigibit RJ45 ports,Video picture can appear,but it isn't active.If connect to 6724-SFP module with GLC-T transceiver,It is OK. configure speed 1000 on the 6148 interface? configure full-duplex on the 6148 interface?
View 2 Replies
View Related
Feb 28, 2008
We are looking for a solution to avoid VPNs to encrypt data between HQ and Bldgs (point-to-multipoint) Gigabit fiber(untrusted media).Is there any cisco's product providing layer2 encryption over Giga fiber?The HQ has a 6509s and remote bldgs have mixed of 3750s,4500s in trunks.
View 2 Replies
View Related
Feb 25, 2012
I have a two computer network. Here are the network adapter details of the two computers.
-Realtek RTL8111E Gigabit Ethernet Controller
-Broadcom NetXtreme Gigabit Ethernet
I'm using a CAT5e cable. But it gives only a 10 MB/s file sharing speed. What is the reason for this? (In both the computers under "Local Area Connection Status" it shows 100 Mbps for the speed)
View 1 Replies
View Related
Jul 12, 2012
I am looking to get a gigabit ethernet adapter for my minecraft server that is quite big now. It used to run off the motherboard but now since its quite big i thought if i should get a good card. It has to be a pci card and compatible with windows 8
View 3 Replies
View Related
Jul 10, 2012
I have the possibility of upgrading a DS3 to Metro Ethernet, Gigabit connection. My dilemma is I have two VTP domains in my network. How can I get two VTP domains over one trunk to a remote site ?
View 0 Replies
View Related
Oct 17, 2012
confirm if "negotiation auto" is supported gigabit port for C3925E router.
Router(config-if)#Interface gi0/2
Router(config-if)#description test link
Router(config-if)# no ip address
Router(config-if)# negotiation auto
^
% Invalid input detected at '^' marker.
View 5 Replies
View Related
