i have a cisco 1921 router and it has ge0/0 (LAN) and ge(0/1) WAN. ge 0/0 is well connected and i can ping it and the LED light is on but ge 0/1 has failed to come up.Ge0/1 is connected to an IDU and has a public IP address. The LED light also does not light on ge 0/1.Where could the problem be?
View 5 RepliesI have an Ethernet Loopback Plug (4 Pairs) made and trying to test the Gigabit Interface on a 3845 Router with a fail result. The interface will show up/up only if I set the interface to 100M/Full Duplex when I plug-in the Ethernet Loopback Plug (4 Pairs). I don't see this Gigabit Interface @ 3845 router has any option to set it to internal or external loopback.
View 2 Replies View RelatedI am having a problem with my Realtek RTL8168D/8111D PCI-E Gigabit Ethernet NIC. It is not detecting my ethernet cable, and thus leaving me without internet on my desktop, after i updated its driver. The cable is not the problem as I have tested the cable with my laptop. I tried rolling back drivers, doing system restore and removing drivers with driversweeper and letting windows install the drivers again. However, none of these worked for me. I doubt the NIC is faulty as it was working before i updated the drivers. I am using windows 7 home premium 64-bit.
View 9 Replies View RelatedSo my old router needed replacement and my dad bought a Netgear gigabit ethernet switch instead of a router. It said that it gets 1Gbps when I look inside the local area connection speed. The problem was we tried to use it like a router but only 2 computers could connect to the internet at one time but it was indeed noticeably faster when it came to video streaming speed. We since returned it and bought a Netgear N600 router that says the speed is 300mbps but like my old router it shows the speed is actually 100mbps and the streaming is good for the most part but every now and then slows down. Would using the ethernet switch with our new router work with streaming speeds and connection stability and of course let more computers connect and also use the routers wireless.
View 13 Replies View RelatedBut I currently have a Linksys E3200 I bought in a moment of weakness after an evening of being pissed off at bricking my old WRT610N. (soft bricked, but I'm beyond screwing with it)
There's nothing *wrong* with it, but I am interested in something that either comes preinstalled with DD-WRT, or is well supported (ie easy to install on) by DD-WRT. I plan on selling the E3200 once I find something to replace it.
My requirements:
-Gigabit
-5 GHz (I have a file server/HTPC; I don't want to be limited to gigabit ethernet)
-$150 or less (I know $150 is high, but I figure I'll get close to that for the E3200)
What is the Cisco 1921 router performance if connected with 2 Giga Ethernet port? What is the performance if enable GRE tunnel ?
View 2 Replies View RelatedWhat are the commands for Configuring Cisco 1921 Route's Gigabit Port G0/0 or G0/1 for Leased Line termination having Ethernet Hands Off
Modem Provided by ISP (BSNL ) is CTR-U
I have a Cisco 2851 router and need an additional gigabit Ethernet port. How to get the part number I need to order?
View 3 Replies View RelatedI recently bought the E4200 thinking it would be the latest and greatest, and I wouldnt' have to worry, but after just a simple test of transferring files between my Home Server, and my PC (Both connected over Gigabit ethernet using CAT6 cables, with only the E4200 inbetween).I use to get anywhere from 40 MegaBytes/second to 50MegaBytes/second on my D-Link 655.But now I am lucky to barely get 20 MegaBytes/second. Is there an issue with this router? or am I expecting too much from Linksys?
View 6 Replies View Relatedhow the ASR1000s are being setup.I am looking at ASR1000s as part of network refresh and was looking at RJ-45 based Gigabit Ethernet ports compatible with the ASR1000s SPA-5X1GE-V2 seems to be an option but they are all SFPs. Are there any options for RJ-45 ones on ASR1000s?
There is an option for the 2 port where one can mix and match SFPs and RJ45 but I was looking for something which is RJ45 only.Are there any options for them available.I know I could get something with FastEthernet type but was looking for the GigabitEthernet type.
Is there a PCI Express 2.0 Gigabit ethernet card [NIC] which i can install in this motherboard where usually one installs NVIDIA graphic cards?
View 4 Replies View RelatedI currently have 2 PCs that are directly connected to each other via a 1Gbs Cat6 connection.I don't currently have a 1Gbs router so what I am doing right now is unhooking this connection and reconnecting both machines to my router when I need internet access. I have ordered some USB Wi-Fi adapters so I can have both machines access the internet that way whilst still use FTP between them on the 1Gbs line.If I were to scrap that idea and get a 1Gbs hub, connect both PCs straight into that, and then also connect the hub to my 100mbits router, would the 2 computers be able to communicate with each other at 1Gbs and then talk to the router at 100mbits, or would the whole network run at 100mbits.I don't really want to have to shell out on a 1Gbs router as I don't need anything else on the network to run at that speed.
View 6 Replies View RelatedPurchased and configured 2951 router based on Telco specs that required T3/DS3 card with coax connection for MPLS. When telco showed up to install DS3 they handed me a UTP copper connection.... Can I use one of the Gigabit ethernet connections on the 2951 as my MPLS interface into the provider's cloud?
View 2 Replies View RelatedWe have a Cisco 7206 VXR Router with NPE-G2. As everybody aware that, It has got 3 x Gigabit Ethernet Ports on this. We would like to add Two more Copper Gigabit Ethernet Interfaces. The Configurator does not show any options to add that.Now we have a doubt that, Does this 7206 VXR support how many Copper Gigabit Ethernet Interface ?. There is no clear answer available in the Data Sheets.
View 2 Replies View RelatedWe have a Cisco 7206 VXR Router with NPE-G2. As everybody aware that, It has got 3 x Gigabit Ethernet Ports on this. We would like to add Two more Copper Gigabit Ethernet Interfaces. The Configurator does not show any options to add that...
Now we have a doubt that, Does this 7206 VXR support how many Copper Gigabit Ethernet Interface ?. There is no clear answer available in the Data Sheets.
I'm going to be upgrading my network (router and network cards etc). I was wondering if there will be any performance difference with the Belkin Fastcat 5e I currently have and CAT6 cables?
View 7 Replies View RelatedI have a Dell Studio running windows 7 sp1. yesterday i was on the internet as normal. Today i was able to connect via my schools wifi, but not my ethernet cable. Device manager shows that my ethernet port should be available.
View 3 Replies View RelatedI have the following problem. I bought two TP-LINK TG-3269 gigabit cards, placed them in two computers and connected them directly. On my Ubuntu system I used iperf tool and measured only 95 Mbit/s. It wont go any faster, I tried many times with different settings.
The indicator lamp shows 1000 Mbit/s.
I am moving into an apartment thereafter. I have an HTPC in use, a personal computer for gaming/processing, and my fiancee has an Apple Macbook Pro that she uses quite often. I have an HDHomeRun Dual (2 tuners) for streaming OTA/QSM cable over the network (the HDHomeRun plugs into the network, not a computer). I also have a TV and Blu-Ray player that have ethernet ports.
Currently I use Verizon Fios and their Actiontec MI424WR router, which to my knowledge has gigabet ethernet. When I move I will probably be saddled with Comcast Xfinity Internet, which will supply a cable modem if I want, but no router. The only router I currently own is a Zyxel NBG-419N, which has only 100/10 ethernet ports. My current computers all have gigabit ethernet. For the home theatre components and my HTPC, I plan to pick up a network switch with gigabit ethernet. So my questions are:
1. If I use the Zyxel and the Comcast cable modem, would I be throttling my network speed at the router? I would hate to choke my speed just because one component does not have gigabit ethernet.
2. If I were to upgrade to, say, an Asus RT-N56U, would that make a huge difference on network browsing and throughput speeds?
3. Finally, what kind of cable is needed to maximize discernible speed increase? Cat5, Cat5e, or Cat6?
I am setting up a 1921 with two ethernet WAN ports going to two seperate ADSL ISP's (via bridged modems) and one connecting to the internal LAN. There is a single e-mail / web server behind the router.
I have been reading the following which is exactly what we want to do, but I have questions. Maybe failover would be better because Load Balancing seems a little too quirky without BGP. url...
How do we define public static IP's, the example seems to show DHCP?In order to detect if a line is down, it has to ping an IP address that is specific to the connection - correct? So could I use the gateway for the ISP? The issue I have with this is the gateway might be up, but the Internet down. Next, we need to make sure that when someone visits one of our public IP addresses, the return data is sent through the connection requested. What we don't want is a situation where incoming connections are not working.From experience, load-balancing causes certain websites and SaaS applications to break because requests are coming from two different ISP's. Is this the case with OER? Finally, any links, config or something to advise how a fail over only configuration would work given we have internal servers (PAT/NAT inbound would need to translate properly with the failover IP)? Basically if ISP 1 goes down, I.E. router cannot ping 8.8.4.4 then it switches to ISP 2, until ISP 1 comes back online and switches back? This would need to change the NAT rules for inbound as described.
I was wondering if I could use the CISCO3945 Integrated Gigabit Ethernet WAN ports for routing, I need to enable BGP and I was willing to use one of those ports.
View 2 Replies View RelatedWe are looking for a solution to avoid VPNs to encrypt data between HQ and Bldgs (point-to-multipoint) Gigabit fiber(untrusted media).Is there any cisco's product providing layer2 encryption over Giga fiber?The HQ has a 6509s and remote bldgs have mixed of 3750s,4500s in trunks.
View 2 Replies View RelatedI have a two computer network. Here are the network adapter details of the two computers.
-Realtek RTL8111E Gigabit Ethernet Controller
-Broadcom NetXtreme Gigabit Ethernet
I'm using a CAT5e cable. But it gives only a 10 MB/s file sharing speed. What is the reason for this? (In both the computers under "Local Area Connection Status" it shows 100 Mbps for the speed)
I am looking to get a gigabit ethernet adapter for my minecraft server that is quite big now. It used to run off the motherboard but now since its quite big i thought if i should get a good card. It has to be a pci card and compatible with windows 8
View 3 Replies View RelatedUsing a small network (WAN) with three 1921 routers (IOS 15.1(T)) connected via E1 links. One host (industrial PC - core 2 due running Win XP Pro) connected to each router. The spare Gigabit Ethernet port on each router is bridged with the active one (so a portable management PC (laptop) can be plugged in there and communicate with the router and the industriual PC.
Multicast routing strategy between the routers is as per "Anycast - Static RP", with PIM sparse-mode enabled on all interfaces and sink RP defined on all three routers.
Problem occurs when a (IPV4) multicast application on one PC communicates with the others:
(a) IGMP V2 membersip reports etc. work correctly at the sender and at the other two PCs receiving the multicast stream
(b) Multicast routing on the WAN is working correctly; running Wireshark on the receiving PCs shows that multicast data is received on the expected group.
(c) But, there is an error in the Ethernet packets
i. The first packet's Ethernet header contains the correct destination MAC address 01:00:5E:aa:bb:cc where aa:bb:cc match with the last three octets of the mulicast group's address, and that packet is received OK by the listening multicast application
ii. However, subsequent packets' Ethernet headers have the wrong MAC address 01:00:5E:00:00:00 (the last three octets are all zeroes and these packets are discarded by Windows on the receiving PC and not seen by the multicast application.
Problem is related to the presence of integrated routing & bridging; if I delete the bridge virtual interface,disable bridging and give the two Gigabit Ethernet ports their own IP addresses, the multicast reception works correctly; all received multicast packets have te expected value on the destination MAC address (matching the group address)I have used the same integrated routing/bridging configuration successfully on Cisco 2611 and 2811 routers and there was no such issue with the multicast packets.Have I overlooked some subtle aspect of configuration in the 1921 router or have I uncovered a bug...?
For reference - snippets from router configuration scripts
:
In the non-working configuration (with Integrated Routing & Bridging)
interface GigabitEthernet0/0
no ip address
duplex auto
speed auto
[code]....
In the working configuration all the bridging is gone and the two Gigabit Ethernet interfaces have a very plain & simple configuration in different subnets
interface GigabitEthernet0/0
ip address 192.168.212.1 255.255.255.128
no ip directed-broadcast
ip pim sparse-mode
duplex auto
[code]....
I have the possibility of upgrading a DS3 to Metro Ethernet, Gigabit connection. My dilemma is I have two VTP domains in my network. How can I get two VTP domains over one trunk to a remote site ?
View 0 Replies View Relatedconfirm if "negotiation auto" is supported gigabit port for C3925E router.
Router(config-if)#Interface gi0/2
Router(config-if)#description test link
Router(config-if)# no ip address
Router(config-if)# negotiation auto
^
% Invalid input detected at '^' marker.
My new computer has a problem with the on-board gigabit ethernet it keeps dropping network connection every few minutes. Nothing has had any effect. It has been such an annoying problem, I really was hoping to find a fix for this sooner as I know other people have had similar issues. Does anyone have any other ideas because I would like to use the only ethernet connection sometime in the near future. Having to run of an WPN11 netgear usb adapter at the moment.
View 8 Replies View RelatedI have setup an Asus RT n16 with 3 computers that support gigabit ethernet and a media server on one floor. On the other floor I have set up a fast ethernet switch (connected to my asus router) which is connected to several fast ethernet enabled computers.
Would the fast ethernet devices slow down the entire gigabit networking to 100mbps connections on my floor - similar to how a wireless n network running at 300mpbs must slow down to 54mbps when a wireless g device is connected to it?
I need to connect one sw3750E with two 3750X , with Uplinks at 10 GBps. My doubt is the next:
Switch 3750E has two TwinGig Adapter Converting 10 Gigabit Ethernet X2, phisically each twinGig adapter has 2 slots for SFP modules. Can I install sfp+ If I want to use copper for Uplink at 10 Gbps, I just need to install one SFP-H10GB-CU5M transceiver ???? the other SFP slot is disabled automatically?
in the other side 3750X in order to support copper at 10 Gbps a C3KX-NM-10G network module is considered, this will be connected to SW3750E by means of SFP-H10GB-CU5M.
The second 3750X will be connected to second twinGig Adapter of 3750E using another SFP-H10GB-CU5M transceiver.
I'm looking (LAN) driver for Win Server 2003 for the MAXIMUS motherboard of ASUS for the lan card
View 1 Replies View RelatedI have two of these computers side by side. The card in issue is recognized, but says no driver. I have copied the driver from the good 580e, downloaded everything I could, and cannot get it? Using Win7, 64 bit, comcast DSL. The bad one just stopped working?
View 1 Replies View RelatedHave just acquired new used HP desktop running Windows Vista. System has a Broadcom NeXtreme Gigabit Ethernet card installed, which gets me to the internet OK when using a LAN cable from wireless router. But I can't make wireless connection. Vista tells me that I need a wireless network adapter.Am I missing something? Is it possible to change some settings to get the Broadcom card to go wireless? If not, what sort of adapter is needed, and is such adapter external or will it have to be installed in the system box?
View 3 Replies View Related