Purchased and configured 2951 router based on Telco specs that required T3/DS3 card with coax connection for MPLS. When telco showed up to install DS3 they handed me a UTP copper connection.... Can I use one of the Gigabit ethernet connections on the 2951 as my MPLS interface into the provider's cloud?
View 2 RepliesInstallation of 2 x 4 Mbps MPLS circuit on primary router (CISCO 2951) and 1 x 8 Mbps Ethernet link on secondary router (Cisco 2951). We have successfully implement the primary router with 2 x 4 Mbps MPLS circuit. Site is having two computer room CR1 and CR2 and distance between both room is 200mts. CR1 is having primary core router and primary core switch where the service provider terminated the new MPLS circuit and we have done the successful implementation. CR2 is having Secondary core router and secondary core switch where we needs to have the termination of Ethernet link but service provider has delivered the Ethernet link on the CR1 which is incorrect DMARC Location.
Both the computer rooms are connected via optical copper can we use that copper to connect the circuit on CR2, as per my understanding we can use the optical fiber to connect the wind circuit on secondary router on CR2 by using the media connector.
Can Cisco2951 work as an MPLS router. If yes what will be needed to make it function as an MPLS router? Else which alternative router can function as an MPLS router.
View 1 Replies View RelatedI want a router to terminate 100Mbps MPLS link on it. Can Cisco 2951 will be suitable for this or i have to go on to 3900 series or 7200 series
View 2 Replies View Relatedsetting up MPLS on a single T3 line. A client has contacted us to set up a 2951 at a branch location. There are 5 locations connected with MPLS.They will split off 4meg of the T3 for mpls. The rest of the 45meg would go to the internet.They have two 1841's currently set up with a T1 line in each. One 1841 connects to the MPLS and the other to the internet.When the T3 is turned up by the provider, everything, internet and MPLS, will go through it. I asked for the current configurations, but I have not received them yet and this setup is due in a couple days.Given I've never configured MPLS before and I have a rudimentary understanding of how it works, any tips or configurations? I'd hate to be stuck on site and not equipped to complete the job.
View 3 Replies View RelatedI have an Ethernet Loopback Plug (4 Pairs) made and trying to test the Gigabit Interface on a 3845 Router with a fail result. The interface will show up/up only if I set the interface to 100M/Full Duplex when I plug-in the Ethernet Loopback Plug (4 Pairs). I don't see this Gigabit Interface @ 3845 router has any option to set it to internal or external loopback.
View 2 Replies View RelatedMy new computer has a problem with the on-board gigabit ethernet it keeps dropping network connection every few minutes. Nothing has had any effect. It has been such an annoying problem, I really was hoping to find a fix for this sooner as I know other people have had similar issues. Does anyone have any other ideas because I would like to use the only ethernet connection sometime in the near future. Having to run of an WPN11 netgear usb adapter at the moment.
View 8 Replies View RelatedI have the possibility of upgrading a DS3 to Metro Ethernet, Gigabit connection. My dilemma is I have two VTP domains in my network. How can I get two VTP domains over one trunk to a remote site ?
View 0 Replies View RelatedHave just acquired new used HP desktop running Windows Vista. System has a Broadcom NeXtreme Gigabit Ethernet card installed, which gets me to the internet OK when using a LAN cable from wireless router. But I can't make wireless connection. Vista tells me that I need a wireless network adapter.Am I missing something? Is it possible to change some settings to get the Broadcom card to go wireless? If not, what sort of adapter is needed, and is such adapter external or will it have to be installed in the system box?
View 3 Replies View RelatedI am having a problem with my Realtek RTL8168D/8111D PCI-E Gigabit Ethernet NIC. It is not detecting my ethernet cable, and thus leaving me without internet on my desktop, after i updated its driver. The cable is not the problem as I have tested the cable with my laptop. I tried rolling back drivers, doing system restore and removing drivers with driversweeper and letting windows install the drivers again. However, none of these worked for me. I doubt the NIC is faulty as it was working before i updated the drivers. I am using windows 7 home premium 64-bit.
View 9 Replies View Relatedthere is a line set with a provider with EoMPLS.This is an international line coming with 10M connectivity.the line is working fine with udp traffic but with tcp we don t get any use more than 1M.
View 7 Replies View RelatedWhat is the advantage of using MPLS compare with Ethernet? And do MPLS provide a internet access?
View 1 Replies View RelatedI have a 1941 router with the security licence. I am setting up both a T1 wic that connects to my enterprise MPLS cloud and one of the two gig interfaces that will connect to my home office through a VPN tunnel to a ASA 5520. I have tried multiple solutions though my gues is that I am making this WAY more difficult than it needs to be. What I am trying to create is a primary on the serial interface and then a failover through the VPN.So far, I have tried to:
-Track the serial interface and then set the default route, based on the tracking
-Create an IP SLA to echo the gateway of the serial interface to change the routing
-Started to create HSRP between the two interfaces though I could not figure out if / how a standby could be put into a sub-interface on the serial
The SLA seems to be working somewhat. The problem is that it is not transparent and sometimes even needs me to clear the VPN tunnel to get things back to smoothly through the serial interface. [code]
i have a cisco 1921 router and it has ge0/0 (LAN) and ge(0/1) WAN. ge 0/0 is well connected and i can ping it and the LED light is on but ge 0/1 has failed to come up.Ge0/1 is connected to an IDU and has a public IP address. The LED light also does not light on ge 0/1.Where could the problem be?
View 5 Replies View Relatedhow the ASR1000s are being setup.I am looking at ASR1000s as part of network refresh and was looking at RJ-45 based Gigabit Ethernet ports compatible with the ASR1000s SPA-5X1GE-V2 seems to be an option but they are all SFPs. Are there any options for RJ-45 ones on ASR1000s?
There is an option for the 2 port where one can mix and match SFPs and RJ45 but I was looking for something which is RJ45 only.Are there any options for them available.I know I could get something with FastEthernet type but was looking for the GigabitEthernet type.
Is there a PCI Express 2.0 Gigabit ethernet card [NIC] which i can install in this motherboard where usually one installs NVIDIA graphic cards?
View 4 Replies View RelatedI currently have 2 PCs that are directly connected to each other via a 1Gbs Cat6 connection.I don't currently have a 1Gbs router so what I am doing right now is unhooking this connection and reconnecting both machines to my router when I need internet access. I have ordered some USB Wi-Fi adapters so I can have both machines access the internet that way whilst still use FTP between them on the 1Gbs line.If I were to scrap that idea and get a 1Gbs hub, connect both PCs straight into that, and then also connect the hub to my 100mbits router, would the 2 computers be able to communicate with each other at 1Gbs and then talk to the router at 100mbits, or would the whole network run at 100mbits.I don't really want to have to shell out on a 1Gbs router as I don't need anything else on the network to run at that speed.
View 6 Replies View RelatedWe have a Cisco 7206 VXR Router with NPE-G2. As everybody aware that, It has got 3 x Gigabit Ethernet Ports on this. We would like to add Two more Copper Gigabit Ethernet Interfaces. The Configurator does not show any options to add that.Now we have a doubt that, Does this 7206 VXR support how many Copper Gigabit Ethernet Interface ?. There is no clear answer available in the Data Sheets.
View 2 Replies View RelatedWe have a Cisco 7206 VXR Router with NPE-G2. As everybody aware that, It has got 3 x Gigabit Ethernet Ports on this. We would like to add Two more Copper Gigabit Ethernet Interfaces. The Configurator does not show any options to add that...
Now we have a doubt that, Does this 7206 VXR support how many Copper Gigabit Ethernet Interface ?. There is no clear answer available in the Data Sheets.
I'm going to be upgrading my network (router and network cards etc). I was wondering if there will be any performance difference with the Belkin Fastcat 5e I currently have and CAT6 cables?
View 7 Replies View RelatedI have a Dell Studio running windows 7 sp1. yesterday i was on the internet as normal. Today i was able to connect via my schools wifi, but not my ethernet cable. Device manager shows that my ethernet port should be available.
View 3 Replies View RelatedSo my old router needed replacement and my dad bought a Netgear gigabit ethernet switch instead of a router. It said that it gets 1Gbps when I look inside the local area connection speed. The problem was we tried to use it like a router but only 2 computers could connect to the internet at one time but it was indeed noticeably faster when it came to video streaming speed. We since returned it and bought a Netgear N600 router that says the speed is 300mbps but like my old router it shows the speed is actually 100mbps and the streaming is good for the most part but every now and then slows down. Would using the ethernet switch with our new router work with streaming speeds and connection stability and of course let more computers connect and also use the routers wireless.
View 13 Replies View RelatedI have the following problem. I bought two TP-LINK TG-3269 gigabit cards, placed them in two computers and connected them directly. On my Ubuntu system I used iperf tool and measured only 95 Mbit/s. It wont go any faster, I tried many times with different settings.
The indicator lamp shows 1000 Mbit/s.
But I currently have a Linksys E3200 I bought in a moment of weakness after an evening of being pissed off at bricking my old WRT610N. (soft bricked, but I'm beyond screwing with it)
There's nothing *wrong* with it, but I am interested in something that either comes preinstalled with DD-WRT, or is well supported (ie easy to install on) by DD-WRT. I plan on selling the E3200 once I find something to replace it.
My requirements:
-Gigabit
-5 GHz (I have a file server/HTPC; I don't want to be limited to gigabit ethernet)
-$150 or less (I know $150 is high, but I figure I'll get close to that for the E3200)
I am moving into an apartment thereafter. I have an HTPC in use, a personal computer for gaming/processing, and my fiancee has an Apple Macbook Pro that she uses quite often. I have an HDHomeRun Dual (2 tuners) for streaming OTA/QSM cable over the network (the HDHomeRun plugs into the network, not a computer). I also have a TV and Blu-Ray player that have ethernet ports.
Currently I use Verizon Fios and their Actiontec MI424WR router, which to my knowledge has gigabet ethernet. When I move I will probably be saddled with Comcast Xfinity Internet, which will supply a cable modem if I want, but no router. The only router I currently own is a Zyxel NBG-419N, which has only 100/10 ethernet ports. My current computers all have gigabit ethernet. For the home theatre components and my HTPC, I plan to pick up a network switch with gigabit ethernet. So my questions are:
1. If I use the Zyxel and the Comcast cable modem, would I be throttling my network speed at the router? I would hate to choke my speed just because one component does not have gigabit ethernet.
2. If I were to upgrade to, say, an Asus RT-N56U, would that make a huge difference on network browsing and throughput speeds?
3. Finally, what kind of cable is needed to maximize discernible speed increase? Cat5, Cat5e, or Cat6?
I was wondering if I could use the CISCO3945 Integrated Gigabit Ethernet WAN ports for routing, I need to enable BGP and I was willing to use one of those ports.
View 2 Replies View RelatedWe are looking for a solution to avoid VPNs to encrypt data between HQ and Bldgs (point-to-multipoint) Gigabit fiber(untrusted media).Is there any cisco's product providing layer2 encryption over Giga fiber?The HQ has a 6509s and remote bldgs have mixed of 3750s,4500s in trunks.
View 2 Replies View RelatedI have a two computer network. Here are the network adapter details of the two computers.
-Realtek RTL8111E Gigabit Ethernet Controller
-Broadcom NetXtreme Gigabit Ethernet
I'm using a CAT5e cable. But it gives only a 10 MB/s file sharing speed. What is the reason for this? (In both the computers under "Local Area Connection Status" it shows 100 Mbps for the speed)
I am looking to get a gigabit ethernet adapter for my minecraft server that is quite big now. It used to run off the motherboard but now since its quite big i thought if i should get a good card. It has to be a pci card and compatible with windows 8
View 3 Replies View Relatedconfirm if "negotiation auto" is supported gigabit port for C3925E router.
Router(config-if)#Interface gi0/2
Router(config-if)#description test link
Router(config-if)# no ip address
Router(config-if)# negotiation auto
^
% Invalid input detected at '^' marker.
I have a Cisco 2851 router and need an additional gigabit Ethernet port. How to get the part number I need to order?
View 3 Replies View RelatedI have setup an Asus RT n16 with 3 computers that support gigabit ethernet and a media server on one floor. On the other floor I have set up a fast ethernet switch (connected to my asus router) which is connected to several fast ethernet enabled computers.
Would the fast ethernet devices slow down the entire gigabit networking to 100mbps connections on my floor - similar to how a wireless n network running at 300mpbs must slow down to 54mbps when a wireless g device is connected to it?
I recently bought the E4200 thinking it would be the latest and greatest, and I wouldnt' have to worry, but after just a simple test of transferring files between my Home Server, and my PC (Both connected over Gigabit ethernet using CAT6 cables, with only the E4200 inbetween).I use to get anywhere from 40 MegaBytes/second to 50MegaBytes/second on my D-Link 655.But now I am lucky to barely get 20 MegaBytes/second. Is there an issue with this router? or am I expecting too much from Linksys?
View 6 Replies View Related