Cisco WAN :: 2951 Working As MPLS Router
Nov 28, 2012Can Cisco2951 work as an MPLS router. If yes what will be needed to make it function as an MPLS router? Else which alternative router can function as an MPLS router.
View 1 Replies
ADVERTISEMENT
Cisco WAN :: Router 2951 Is Suitable For 100 Mbps MPLS Link?
Aug 28, 2011I want a router to terminate 100Mbps MPLS link on it. Can Cisco 2951 will be suitable for this or i have to go on to 3900 series or 7200 series
View 2 Replies View RelatedCisco WAN :: Possible To Use Gigabit Ethernet On 2951 ISR For MPLS Connection?
Dec 15, 2011Purchased and configured 2951 router based on Telco specs that required T3/DS3 card with coax connection for MPLS. When telco showed up to install DS3 they handed me a UTP copper connection.... Can I use one of the Gigabit ethernet connections on the 2951 as my MPLS interface into the provider's cloud?
View 2 Replies View RelatedCisco WAN :: 2951 / MPLS Branch Site Setup On T3 Line
May 24, 2013setting up MPLS on a single T3 line. A client has contacted us to set up a 2951 at a branch location. There are 5 locations connected with MPLS.They will split off 4meg of the T3 for mpls. The rest of the 45meg would go to the internet.They have two 1841's currently set up with a T1 line in each. One 1841 connects to the MPLS and the other to the internet.When the T3 is turned up by the provider, everything, internet and MPLS, will go through it. I asked for the current configurations, but I have not received them yet and this setup is due in a couple days.Given I've never configured MPLS before and I have a rudimentary understanding of how it works, any tips or configurations? I'd hate to be stuck on site and not equipped to complete the job.
View 3 Replies View RelatedCisco WAN :: Route Map On 2951 Router Not Working?
Jun 29, 2012One of the route maps doesnt want to work, all the other are fine -
route-map vlan23-out permit 40
match ip address 123
set ip next-hop 87.194.168.1
If it take the ip policy off interface gi0/0.123 the client can access the internet OK but over the wrong ISP?As soon as i add the policy all internet stops
Cisco WAN :: 2951 - Installation Of 2x4 Mbps MPLS Circuit And 1x8 Mbps Ethernet Link
Feb 18, 2013Installation of 2 x 4 Mbps MPLS circuit on primary router (CISCO 2951) and 1 x 8 Mbps Ethernet link on secondary router (Cisco 2951). We have successfully implement the primary router with 2 x 4 Mbps MPLS circuit. Site is having two computer room CR1 and CR2 and distance between both room is 200mts. CR1 is having primary core router and primary core switch where the service provider terminated the new MPLS circuit and we have done the successful implementation. CR2 is having Secondary core router and secondary core switch where we needs to have the termination of Ethernet link but service provider has delivered the Ethernet link on the CR1 which is incorrect DMARC Location.
Both the computer rooms are connected via optical copper can we use that copper to connect the circuit on CR2, as per my understanding we can use the optical fiber to connect the wind circuit on secondary router on CR2 by using the media connector.
Cisco WAN :: Asr 1002 Getting A PTP Connection Over MPLS Working
Nov 23, 2011I've been working with a company in the UK to get a PTP connection setup between Minneapolis, MN and Chicago, IL. At each site with have a ASR1002. The connection is made via a fiber connection from Level 3. Level 3 is just handling layer 2 and we are to take care of everything else. As of right now they can see the mac address of the Minneapolis port in the Chicago router. But, I can't see theirs. Nor can I ping the Chicago router. The config that was give to me by the higher engineers is simple enough.
View 3 Replies View RelatedCisco WAN :: MPLS Ipv6 Not Working For Some Reason
Sep 6, 2012I have v4 mpls working fine but v6 refuses to work correctly.Looking at the ipv6 routing table for the VRF we can see prefix's coming from the remote PE's BGP is up in vpnv6 and ipv6 unicast.Everything seems fine but I just cant seem to ping between the sites.as mentioned, ipv4 works fine for the same vrf.
View 16 Replies View RelatedCisco :: 7206 MPLS To Export Netflow From Its MPLS
Jul 11, 2012I have P router (7206VXR) and I need to export netflow from its MPLS interfaces to the netflow software.
View 2 Replies View RelatedCisco WAN :: Configuring Interfaces On 2951 Router?
Dec 27, 2011configuring my Cisco 2951 router. There are three routed interfaces that I need to configure: one for the internal LAN, the second for another private subnet that connects to a Data Centre and the third for the WAN connection. I have configured the Ge0/0 interface as the LAN interface with the internal network 10.17.0.0/24. I have also configured my WAN interface Ge0/1 for internet connectivity. Now, I need to configure the third interface Ge0/2 that will connect to the Data Centre. This will be a private point to point switched ethernet link. The Data Centre will host a secondary domain controlller. So, I want it to be on the same network as the internal LAN, i.e., 10.17.0.0/24. I want to be able to see all other devices that will be located at the Data Centre just like I would see all devices connected to the internal LAN.The problem I am facing is that Cisco 2951 does not allow me to configure two routed interfaces to be on the same subnet. Is there any way to work around this problem and configure both the internal LAN and the Data Centre private network to be on the same subnet.
View 6 Replies View RelatedCisco WAN :: Recommended Router Platform As 2951
Oct 17, 2012I currently have a 50Mbps Internet Connection provided by an ethernet handoff for hosting some webservers. We are looking at adding an additional 10Mbps Internetn connection and route BGP between the two. For the 50Mbps connection, i'm using a Cisco 2951 router. I also have another 2951 router to terminate the 10Mbps connection. Does these router have enough horsepower to fully route BGP?
View 1 Replies View RelatedCisco WAN :: Tunnel Interfaces On 2951 Router
Apr 11, 2011We have just installed our first 2951 router, and were suprised to see in our Netflow collector that Tunnel interfaces appeared even though we did not configure any, I have seen other posts talking about PIM tunnel when using Multicast, but we dont use multicast and the tunnel is GRE questions are, where do these interfaces come from? how do they pick up an IP address? can we shut them down? IOS is 150-1.M4 loopback interface ip address is 172.16.224.238 ( tunnel source) see output from sh int below
Tunnel0 is up, line protocol is up Hardware is Tunnel Interface is unnumbered. Using address of Tunnel1 (172.16.0.1) MTU 17912 bytes, BW 100 Kbit/sec, DLY 50000 usec, reliability 255/255, txload 99/255, rxload 1/255 Encapsulation TUNNEL, loopback not
[Code]......
Cisco WAN :: 2951 Picking Right Router For Load?
Jul 25, 2011I have talked to two Cisco Reps via our distributor and explained our network to them both and asked for suggested equipment. Our infrastructure has 4 circuits coming into the data center from our remote sites. Two of the circuits are cat5 and two are DS3. I want to use two routers to support two circuits each (cat5 and DS3). Each circuit is around 30Mb servicing around 13 locations with T1 connections, 55 locations in total. They suggested at a minimum the cisco 2951 model because we are utilizing one NM-1T3/E3 module in each router, and suggested getting the cisco 3925 model to cover future growth. I asked for a data sheet that has suggested models of routers for the bandwidth of the incoming pipes. The technicians said they would email this information over but twice now I have not received it and cannot find this information anywhere online. We currently have a cisco 2851 utilizing one NM-1T3/E3 module and they purchased a cisco 2911 to replace this unit.
View 2 Replies View RelatedCisco Switching/Routing :: 2951 Router Not Able To Connect?
Apr 29, 2012on-plus see the device and allows CPE( imbedded) to start then never opens,,,tried genera connection and used that address supplied to open CCP no discovery.also seems onplus doesn't see a service contract or firmware, etc
View 1 Replies View RelatedCisco Infrastructure :: 2951 Router Boot Error?
Sep 24, 2012I recently received these routers and after the first reboot I changed the user id and password so it does not lock out...After configuring my routers for installation, upon bootup I am getting this message scroll down my screen
monitor: command "
Cisco WAN :: NM-8CE1T1-PRI Module Supported On 2951 Router
Jan 22, 2012Is this module supported in the CISCO2900 routers?I have come across two documents that seem to contradict each other:In this one says:
Cisco 8-Port Channelized T1/E1 and ISDN PRI High-Speed WAN Network Module
#
–Part number: NM-8CE1T1-PRI
#
–Provides channelized T1 or E1 connections or ISDN PRI connection
#
–Supported on Cisco 3800, Cisco 2900, and Cisco 3900 series routers
[code].....
Cisco WAN :: Moving From Pix 515e To 2951 Router With Firewall Feature Set
Dec 29, 2011Me to a 2951 router with fireawall featureset. Ive begun to move the ACLs that where in the pix. However some of the rules are allowed to be typed in bur when i look at the ACL afterwards they are not what i typed in.
View 2 Replies View RelatedCisco Infrastructure :: Can't Use Network Assistant To Connect To 2951 Router
Oct 22, 2012CNA version is 7.5(6)
router: Cisco 2951
error: unable to connect
are able to connect to other switches, such as 2970 questions:
1. is there any configuration needs to be done to connect to 2951 though CNA?
2. is 2951 supported device in CNA?
Cisco Switching/Routing :: Obtain Lastest IOS For New Router 2951?
Jan 11, 2012We have purchased a new 2951 router with IOS version 2951-universalk9-mz.SPA.150-1 and we would like to upgrade to c2951-universalk9-mz.SPA.152-2.T.bin.
View 1 Replies View RelatedCisco WAN :: 150 3G Router On MPLS Network
Mar 24, 2013I currently have a 150 nodes MPLS network. My management is anxious to join some sites with 3G routers as their centres move around a lot.My current MPLS site as 4 x Ps with lots of PEs linking to the 150 x CEs. Is there a way to easily link up my 3G routers to my MPLS network? I have heard DMVPN may be a solution, but not sure how to implement.
View 4 Replies View RelatedCisco WAN :: MPLS Connection On 861 K9 Router?
Jan 5, 2011Recently i purchased Cisco 861-K9 router for my head office.
I have 2 offices (1 is head-office & other is Branch.). i have MPLS Connectivity between 2 offices.
i used 861-K9 WAN port for MPLS Connection.
My question is "is it possible to use the FastEthernet Port of 861-K9 router for connecting the internet Link ?"
Cisco WAN :: Implement MPLS On 2651 Router?
May 18, 2012I have some Cisco 2651 routers, I was trying to implement MPLS on those routers, Can i accomplish this upgrading newer IOS version? link to download the supported IOS.
View 2 Replies View RelatedCisco WAN :: Internet Failover Via MPLS 2821 Router?
Jun 13, 2012Currently I'm looking for a way to failover our internet connection from one site to another site over our MPLS line, should that internet connection go down.
My layout: Internet > Cable internet modem (Site B) > ASA 5510 (Site B) > 2821 Router (Site B) > MPLS Line > 2821 Router (Site A) > ASA5510 (Site A) > ISP provider internet router (Site A) > Internet
Facts:Site B is the one with the internet issues.The MPLS line is routed using BGP. [URL]
Cisco WAN :: 2921 Router For Both MPLS And Internet Connection
Apr 4, 2011i m planning to use the 2921 router for both mpls and internet connection , to 2 different isp also am planning to use bgp with a public providor independant
i m planning to buy sla for the mpls link
Cisco WAN :: 1841 Router LAN Port Hanging On MPLS?
Oct 30, 2011I have 3 locations connected with MPLS connectivity … 2 mbps , 2 mbps branches and 4 mbps and I have Cisco 1841 router ?Last few days I am facing problem that Cisco 1841 router’s Lan port suddenly stop working and connectivity get disconnected.In this stage branch offices can reach up to CISCO 1841 WAN port.
( I have changed 2 different router assuming router problem but issues remain same, Hence No hardware problem )
Cisco WAN :: MPLS For ISP Offers Managed Router 2900
May 14, 2013I wanted to get some opinions on the topic above. We are purchasing MPLS services from a large ISP and they offer a managed router option. I will also have a Cisco ISR 2900 at each site running SRST for my voice system. I have some experience with BGP and am not scared at all to support it if need be. That said, I am currently looking at pros and cons of going with a managed router from this company vs managing my own. Actually, I will manage my own regardless and would just plug it into the managed router. My router is perfectly capable of handling the BGP protocol but I am hoping that I can get some opinions from all of you.
View 6 Replies View RelatedCisco Firewall :: Administration Of ASA5520 And Router Mpls 1900
Jul 31, 2012i just want to administor cisco ASA5520 and cisco router mpls 1900 can some tell me as admin what to check as u get into office /reguraly in cisco asa 5520 and vpn mpls router for administrator ,right now its working as configured by supplier for remote sites to connect HQ and access several server,My interest to know what are the basic day to day checkup on cisco asa5520 working as ips and cisco asa 5520 working as content filtering and cisco vpn mpls
View 2 Replies View RelatedCisco WAN :: Running MPLS - 6503 Switch Or 7201 Router?
Oct 16, 2012I am looking at running MPLS from from one datacentre to the other (we have a layer2 interconnect and can run jumbo frames) I need about 70 access ports (each in a seperate VRF) at the new datacentre
I am looking at :
2x 6503'-Es with sup720-3B and a 48x port linecard
or
2x 7201 router with 2x 2960-S layer 2 access switches.
Cisco WAN :: Test A MPLS Capability With1841 Router And HWIC-4ESW
Oct 11, 2012We are planning on moving towards MPLS. I want to test a MPLS capability with Cisco 1841 Router and a HWIC-4ESW. Is it possible to use the MPLS withe mentioned devices?
View 1 Replies View RelatedCisco WAN :: 5510 Two Router Branch Routing Design With T1 MPLS And ADSL
Feb 29, 2012I'm looking for Routing Design scenarios to complete our configuration needs for remote branches. We will have two 1921 routers in each location, one with a T1 from our MPLS carrier, the other with a DSL connection from an ISP. The T1 router will have an assigned AS and use BGP to router back to head quarters. The DSL router will have an IPSec tunnel back to an ASA 5510 at head quarters. I envisions a GRE tunnel from the DSL router back to head end routers connecting to MPLS at head quarters. Not sure yet how to manipuate the routing between head quarters and the branches such that the T1 router is the primary route to and from the branches and the DSL router is for failover/backup.
View 1 Replies View RelatedCisco Switching/Routing :: 2951 - HSRP Backup Taking Two Minutes When Switching Off Primary Router
Oct 7, 2012I configure HSRP on Router 2951 as a primary router, and Router 2811 as backup router. But when I am switching off my Primary router the backup router is taking 2 mins to take over form primary router.
[code]....
Cisco Switching/Routing :: 1941 / K9 VPN Router MPLS IPVPN Point-to-point
Mar 15, 2012I have 2 cisco 1941/K9 vpn router. I have configured both with LAN ip address given by our vpn provider which is 172.10.10.1 and the other is 172.10.20.1. Both IP addresses are configured to GigabitEthernet port 0/0 on both routers.
1. Is it possible to configure our own set of ip address like 10.71.10.1 and 10.71.50.1 on the GE 0/0 port?
2. Or can we configure our own set of ip addresses (10.71.10.1 and 10.71.50.1) to GigabitEthernet port 0/1 and maintain the other ip addresses on port 0/0?
The first purpose is to have our own set of ip addresses for LAN connection and I will be able to connect or telnet whichever ip address or port is up.
Cisco WAN :: 2951 For BGP At AS Edge?
Mar 6, 2012our customer has a server farm in a data center.At the moment the farm has connectivity with only one ISP but sometimes it has service discontinuity.Customer wants to become AS and having two ISP connectivity for backup purposes.He needs to evaluete two cisco routers to use at AS edge with BGP.At the moment he says that the throughputh with the server farm is max 15Mbps and in the future he thinks that it will not increase.We think about cisco2951 routers with 2GB ram.Is cisco 2951 adeguate for this task ?
View 3 Replies View Related