I have talked to two Cisco Reps via our distributor and explained our network to them both and asked for suggested equipment. Our infrastructure has 4 circuits coming into the data center from our remote sites. Two of the circuits are cat5 and two are DS3. I want to use two routers to support two circuits each (cat5 and DS3). Each circuit is around 30Mb servicing around 13 locations with T1 connections, 55 locations in total. They suggested at a minimum the cisco 2951 model because we are utilizing one NM-1T3/E3 module in each router, and suggested getting the cisco 3925 model to cover future growth. I asked for a data sheet that has suggested models of routers for the bandwidth of the incoming pipes. The technicians said they would email this information over but twice now I have not received it and cannot find this information anywhere online. We currently have a cisco 2851 utilizing one NM-1T3/E3 module and they purchased a cisco 2911 to replace this unit.
hp 3060 j610 had to re new my router now the printer cant connct to itprinter asks me to press wps button on router but cant se any button it then says press ok and starts counting down but cant find router
I have tried to put a password on my dlink-615 wireless router, however, this attempt failed and as a result it is no longer picking up the next work signals from my modem.
I have a belkin n300 wireless router that i know works because the ps3 connects to it but when i tried to add my desktop to the wireless router i used the installation cd to download onto the computer (which i was then told by belkin tech support that the cd was only for extra stuff like printers..) when i installed the cd it said not reccommended to install because it wasnt windows xp authorized but i did this any ways.. i have also been looking online for diferent things to do to try and get my computer to connect to the router so i have changed things on the computer that i have no idea how to backtrack and take it all back..i tried rrstoring my system to an earlier date and it wont do it. now my computer wont even pick up on a wireless connection.. i then tried to connect directly to the modem (comcast box) and i still couldnt get on internet!
I have a Linksys wrt54g wireless router.I have my modem connected to it through ethernet. All of the lights on my modem are on, except for the standby light which isn't supposed to be on. My router says it has internet and it says wlan is active. But still no internet. I get local only. I went on my setup page for my router. I went to status and its telling me that my ip address, subnet mask, and default gateway are all 0.0.0.0 All 3 dns spots are blank. I did a dhcp release and renew. Still all 0's. I did factory defaults. Still nothing. I did ipconfig /all on my desktop and its listing my dns, my default gateway, my dhcp server, my ipv4 address and my dns suffix.
configuring my Cisco 2951 router. There are three routed interfaces that I need to configure: one for the internal LAN, the second for another private subnet that connects to a Data Centre and the third for the WAN connection. I have configured the Ge0/0 interface as the LAN interface with the internal network 10.17.0.0/24. I have also configured my WAN interface Ge0/1 for internet connectivity. Now, I need to configure the third interface Ge0/2 that will connect to the Data Centre. This will be a private point to point switched ethernet link. The Data Centre will host a secondary domain controlller. So, I want it to be on the same network as the internal LAN, i.e., 10.17.0.0/24. I want to be able to see all other devices that will be located at the Data Centre just like I would see all devices connected to the internal LAN.The problem I am facing is that Cisco 2951 does not allow me to configure two routed interfaces to be on the same subnet. Is there any way to work around this problem and configure both the internal LAN and the Data Centre private network to be on the same subnet.
I currently have a 50Mbps Internet Connection provided by an ethernet handoff for hosting some webservers. We are looking at adding an additional 10Mbps Internetn connection and route BGP between the two. For the 50Mbps connection, i'm using a Cisco 2951 router. I also have another 2951 router to terminate the 10Mbps connection. Does these router have enough horsepower to fully route BGP?
We have just installed our first 2951 router, and were suprised to see in our Netflow collector that Tunnel interfaces appeared even though we did not configure any, I have seen other posts talking about PIM tunnel when using Multicast, but we dont use multicast and the tunnel is GRE questions are, where do these interfaces come from? how do they pick up an IP address? can we shut them down? IOS is 150-1.M4 loopback interface ip address is 172.16.224.238 ( tunnel source) see output from sh int below
Tunnel0 is up, line protocol is up Hardware is Tunnel Interface is unnumbered. Using address of Tunnel1 (172.16.0.1) MTU 17912 bytes, BW 100 Kbit/sec, DLY 50000 usec, reliability 255/255, txload 99/255, rxload 1/255 Encapsulation TUNNEL, loopback not
One of the route maps doesnt want to work, all the other are fine -
route-map vlan23-out permit 40 match ip address 123 set ip next-hop 87.194.168.1
If it take the ip policy off interface gi0/0.123 the client can access the internet OK but over the wrong ISP?As soon as i add the policy all internet stops
Can Cisco2951 work as an MPLS router. If yes what will be needed to make it function as an MPLS router? Else which alternative router can function as an MPLS router.
on-plus see the device and allows CPE( imbedded) to start then never opens,,,tried genera connection and used that address supplied to open CCP no discovery.also seems onplus doesn't see a service contract or firmware, etc
I recently received these routers and after the first reboot I changed the user id and password so it does not lock out...After configuring my routers for installation, upon bootup I am getting this message scroll down my screen
Is this module supported in the CISCO2900 routers?I have come across two documents that seem to contradict each other:In this one says:
Cisco 8-Port Channelized T1/E1 and ISDN PRI High-Speed WAN Network Module # –Part number: NM-8CE1T1-PRI # –Provides channelized T1 or E1 connections or ISDN PRI connection # –Supported on Cisco 3800, Cisco 2900, and Cisco 3900 series routers
Me to a 2951 router with fireawall featureset. Ive begun to move the ACLs that where in the pix. However some of the rules are allowed to be typed in bur when i look at the ACL afterwards they are not what i typed in.
We have purchased a new 2951 router with IOS version 2951-universalk9-mz.SPA.150-1 and we would like to upgrade to c2951-universalk9-mz.SPA.152-2.T.bin.
I've just bought a new Samsung 3 series laptop (Windows 7 Home Premium 64 bit). I have two braodband lines at my home (1: Sky with standard Sky wireless router. 2: BT with Netgear wireless router). The Netgear router is primarily used for business but I also use it to connect with my old Dell laptop and my iPad. However I cant seem to connect with my new Samsung laptop to the Netgear router. I want to get rid of the Sky broadband line but neet to get the Netgear line working correctly first.If i turn the Netgear router off and then on again the laptop can see the router and picks up the wireless signal and connects for a few minutes before it drops off and then it can find it again. The laptop does similar with the Sky router except that the connection seems to last longer before it drops off and at least it can always see the Sky wireless signal for me to reconnect again.
my d-link modem is connected and was providing great wireless service to numerous devices around the house until yesterday. The wireless lights are on and stable, but we can't connect. We've tried resetting and turning off to no avail. This computer is connected via an ethernet cable through the modem
I just bought a Gateway dx4860-Ub33P.I took it to geek squad and had them upgrade the video card to Nvidia geforce GTX 560 as well as upgrading the power supply.When I set up the computer at my home office, the wireless adapter is not picking up the signals. My laptop is picking up the wireless signals just fine so I know it can't be a signal strength issue.My Gateway does detect one very weak network, but not nearly as many as my laptop. I also have Norton Antivirus installed if that is at all useful.
Ok, so I've got a Billion BiPac 3011N Wireless-N usb adapter for my PC. I've used it before about a year ago and it was working fine then. But after not using it for a year, I plugged it into my PC, installed the updated drivers, and nothing happened.The Realtek 11n USB wireless lan utility program (came with the driver) does not seem to find the wireless network, something that my laptop picks up easily. I have even tried moving my PC closer to the router, but it still picks up nothing. The utility programme just says 'disconnected'
My laptop has suddenly stopped connecting wirelessly. Just fine with ethernet though. My Wireless adapter is enabled and showing fine in Device Manager and has the latest driver. Wireless Zero Configuration is enabled in services. I tried simply disabling and then re-enabling the wireless adapter but still no luck. I tried selecting the repair option for the wireless adapter and I get the exclamation in yellow triangle deal. I checked to see if I was having issues with firewall and that's not it either. When I click "View Available Wireless Networks" the dozen or so networks that use to appear are gone. I power cycled and reset my modem with no luck. I've also did an ipconfig /release and ipconfig /renew in CMD but nothing changed. I have not changed any wireless settings for my NIC or modem/router and don't understand what else I can do.
Microsoft Windows XP [Version 5.1.2600] (C) Copyright 1985-2001 Microsoft Corp. C:Documents and SettingsJohn>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : john-433101c601 Primary Dns Suffix . . . . . . . :
I have recently been having trouble with my wireless network. My laptop will pick up other networks but not my network. However my iPod and parent's computer will pick up the network that we use. I have a Fujitsu Lifebook N6470 with Windows Vista installed on it. The network adaptor is an Atheros AR5008X Wireless Network Adaptor.
I recently bought 2 SRP527W for customer and i am trying to install them. I have updated the firmware to the latest version. Problem: It can detect BTs business ADSL but the Logical Link is not picking up. I have checked and rechecked the setting with BT but no joy. the original BT router works.
My internet connect sometimes and other time is won't do nothing at all it picking up the network just won't pull up anything. I just flush my dns and still no luck.
For other three years, me and my brother have both been connected to our router via ethernet cables. On this Tuesday just gone, however, my brother took it upon himself to mess with the router whilst I was out. Apparently, his internet had been down since we'd had a power-cut on the Sunday, (My internet was fine, and always has been and was fully functional after said power-cut), and before then, it'd been going really slow, and sometimes cutting out. Okay, no problem. Now, the the thing is, that morning, I was on my internet, all happy, and when I returned home that evening, my PC wouldn't connect. My PC still refuses to connect, three days on. It's not even picking up that there's something plugged in.the router is actually flashing to say that my PC is plugged in and connected to the router. I know that there is nothing wrong with the modem or what have you, as I linked my laptop up to my PC via a cable earlier today to try and get it online. It's not a virus program problem, either. Like I said, it was working Tuesday morning, nine hours later, I come home, my brother restarted/unplugged the router, and now my PC won't connect. I should also note that he's now had to go wireless via a dongle, and everyone else in the house uses wireless laptops. I can't connect my PC to the internet with a dongle
Microsoft Windows [Version 6.1.7600] Copyright (c) 2009 Microsoft Corporation. All rights reserved. C:Windowssystem32>ipconfig/all
My daughter has an asus x5dc laptop with windows 7 which was working fine but then stopped picking up our broadband connection. I have tried restarting laptop and making the connection but get message saying No connections available. I have another laptop using the same NETGEAR DG834GT wireless router perfectly well.
For some reason the laptop my friend brought over is not connecting to the internet and has had a problem connecting to the internet for awhile apparently. At first i thought it was just because his mom accidently hit the hotkey to turn off the wifi so i turned it back on and it still will not connect to the internet. The Mac and the PC i am using to write in this forum work just fine as well as the xbox.
Only I have encountered this problem with my Philips 6356 router. I have spent 2.5 hours on the phone to Samsung and to the tech support from the store I bought it from and no one seems to be able to give me a definitive resolution! I can only assume the router is not compatible with the wifi connector in the laptop.
I have just reformatted my windows 7 ultimate. I have installed the Ethernet driver that came in the motherboard utilities CD. But the problem is computer is not picking up my network and its just saying unidentified public network and i cannot connect to the internet.The modem i use is Netgear cable voice gateway CVG824G. The connection is cable internet.
