Is this module supported in the CISCO2900 routers?I have come across two documents that seem to contradict each other:In this one says:
Cisco 8-Port Channelized T1/E1 and ISDN PRI High-Speed WAN Network Module
#
–Part number: NM-8CE1T1-PRI
#
–Provides channelized T1 or E1 connections or ISDN PRI connection
#
–Supported on Cisco 3800, Cisco 2900, and Cisco 3900 series routers
[code].....
I have the situation with my new Cisco 2951 router. It has only one module on board - SM-D-ES3-48-P. I don't know what is wrong but I can't see any information about this module. When I connect my laptop to any port it's become green, but it's still green even after I disconnect PC from this port. Sh ip int brief command shows only built-in gigabit interfaces. I also connect my second PC to the router by console to monitor any changes when I connect or disconnect laptop to the module's ports. [code]
View 3 Replies View RelatedAny doc for installing the a PoE switch module for a 2951? I find alot about the 2951 PoE Power supply but nothing for the switch module.
View 5 Replies View RelatedI'm trying to set up a 2951 with a 24 port switch module. I want the ports to act similiarly to the ports on an 881 router - where I assign the VLANs on the router and I set the VLANs to the switchport interfaces.I would like to be able to create the VLANs on the router portion of the 2951 and then, enter the switch module and configure the Ports to the VLANs but, how do I logically connect router to the switch? Is it an internal logical interface - meaning how are the VLANs getting from the router to the switch?
View 24 Replies View RelatedI have one of my customer have cisco 2951 Router with two ISP and two ADSL module .i already configure one ADSL module.rit now customer want secondISP ( ADSL) module configuration separate netwok because customer have Access pont they want connect directly to router is it possible
1st ISP already running but customer requirement 2nd ISP superate network with Access pont not redundancy
I have checked on Cisco.com and as per a module support document for ISR's G2, the NM-1CE1TI-PRI module is not supported on new ISR's.
Grateful if more clarification could be obtained about the above.
Will be router not detect the module when inserted in the chassis?
I would like to know if WS-X6848-SFP modules are supported with LMS Prime 4.1 and 4.2.
View 2 Replies View Relatedwhat is that mean-"Redundancy is not supported between an ACE module and an ACE appliance operating as peers" I'm designing network in which I plan to use ACE-4710-0.5F-K9 appliances.
View 1 Replies View RelatedI have a 1t3/e3 card in a new 2951. When I statred the router, I found no interface corresponding to this module when do "show ip interface brief"
View 3 Replies View RelatedI have inherited a 3945E router with an NM-8CE1T1-PRI card installed in slot 2 using the SM-NM adapter card. The command 'card type E1 2' has been issued but I only see interfaces Serial2/0:0 to Serial2/0:30.
Since it as 8 port card I was also expecting there to be
Serial2/1:0 to Serial2/1:30
Serial2/2:0 to Serial2/2:30
etc etc.......
Serial2/7:0 to Serial2/7:30
The router will not allow me to issue a sub slot number with the card type command.
Am I missing something in the configuration or is there an issue with this card and router combination? The show inventory has the following:
NAME: "Network Module Adapter for SM Slot on Slot 2", DESCR: "Network Module Adapter for SM Slot"
PID: SM-NM-ADPTR , VID: V01, SN: FOCxxxxxxxx
NAME: "8 port channelized and PRI T1/E1 NM on Slot 2", DESCR: "8 port channelized and PRI T1/E1 NM"
PID: NM-8CE1T1-PRI , VID: V01 , SN: FOCxxxxxxxx
It doesn't give any errors when booting up and the router is running c3900e-universalk9-mz.SPA.152-1.T.bin IOS.
configuring my Cisco 2951 router. There are three routed interfaces that I need to configure: one for the internal LAN, the second for another private subnet that connects to a Data Centre and the third for the WAN connection. I have configured the Ge0/0 interface as the LAN interface with the internal network 10.17.0.0/24. I have also configured my WAN interface Ge0/1 for internet connectivity. Now, I need to configure the third interface Ge0/2 that will connect to the Data Centre. This will be a private point to point switched ethernet link. The Data Centre will host a secondary domain controlller. So, I want it to be on the same network as the internal LAN, i.e., 10.17.0.0/24. I want to be able to see all other devices that will be located at the Data Centre just like I would see all devices connected to the internal LAN.The problem I am facing is that Cisco 2951 does not allow me to configure two routed interfaces to be on the same subnet. Is there any way to work around this problem and configure both the internal LAN and the Data Centre private network to be on the same subnet.
View 6 Replies View RelatedI currently have a 50Mbps Internet Connection provided by an ethernet handoff for hosting some webservers. We are looking at adding an additional 10Mbps Internetn connection and route BGP between the two. For the 50Mbps connection, i'm using a Cisco 2951 router. I also have another 2951 router to terminate the 10Mbps connection. Does these router have enough horsepower to fully route BGP?
View 1 Replies View RelatedWe have just installed our first 2951 router, and were suprised to see in our Netflow collector that Tunnel interfaces appeared even though we did not configure any, I have seen other posts talking about PIM tunnel when using Multicast, but we dont use multicast and the tunnel is GRE questions are, where do these interfaces come from? how do they pick up an IP address? can we shut them down? IOS is 150-1.M4 loopback interface ip address is 172.16.224.238 ( tunnel source) see output from sh int below
Tunnel0 is up, line protocol is up Hardware is Tunnel Interface is unnumbered. Using address of Tunnel1 (172.16.0.1) MTU 17912 bytes, BW 100 Kbit/sec, DLY 50000 usec, reliability 255/255, txload 99/255, rxload 1/255 Encapsulation TUNNEL, loopback not
[Code]......
One of the route maps doesnt want to work, all the other are fine -
route-map vlan23-out permit 40
match ip address 123
set ip next-hop 87.194.168.1
If it take the ip policy off interface gi0/0.123 the client can access the internet OK but over the wrong ISP?As soon as i add the policy all internet stops
Can Cisco2951 work as an MPLS router. If yes what will be needed to make it function as an MPLS router? Else which alternative router can function as an MPLS router.
View 1 Replies View RelatedI have talked to two Cisco Reps via our distributor and explained our network to them both and asked for suggested equipment. Our infrastructure has 4 circuits coming into the data center from our remote sites. Two of the circuits are cat5 and two are DS3. I want to use two routers to support two circuits each (cat5 and DS3). Each circuit is around 30Mb servicing around 13 locations with T1 connections, 55 locations in total. They suggested at a minimum the cisco 2951 model because we are utilizing one NM-1T3/E3 module in each router, and suggested getting the cisco 3925 model to cover future growth. I asked for a data sheet that has suggested models of routers for the bandwidth of the incoming pipes. The technicians said they would email this information over but twice now I have not received it and cannot find this information anywhere online. We currently have a cisco 2851 utilizing one NM-1T3/E3 module and they purchased a cisco 2911 to replace this unit.
View 2 Replies View Relatedon-plus see the device and allows CPE( imbedded) to start then never opens,,,tried genera connection and used that address supplied to open CCP no discovery.also seems onplus doesn't see a service contract or firmware, etc
View 1 Replies View RelatedI recently received these routers and after the first reboot I changed the user id and password so it does not lock out...After configuring my routers for installation, upon bootup I am getting this message scroll down my screen
monitor: command "
Me to a 2951 router with fireawall featureset. Ive begun to move the ACLs that where in the pix. However some of the rules are allowed to be typed in bur when i look at the ACL afterwards they are not what i typed in.
View 2 Replies View RelatedCNA version is 7.5(6)
router: Cisco 2951
error: unable to connect
are able to connect to other switches, such as 2970 questions:
1. is there any configuration needs to be done to connect to 2951 though CNA?
2. is 2951 supported device in CNA?
I want a router to terminate 100Mbps MPLS link on it. Can Cisco 2951 will be suitable for this or i have to go on to 3900 series or 7200 series
View 2 Replies View RelatedWe have purchased a new 2951 router with IOS version 2951-universalk9-mz.SPA.150-1 and we would like to upgrade to c2951-universalk9-mz.SPA.152-2.T.bin.
View 1 Replies View RelatedI configure HSRP on Router 2951 as a primary router, and Router 2811 as backup router. But when I am switching off my Primary router the backup router is taking 2 mins to take over form primary router.
[code]....
We are planning to configure the ipv6 PBR on our 7606 routers. We have configured the route-maps successfully .but when we tried to apply those on interfaces we are facing an problem .
when we trying to give command # ipv6 policy route-map <route map name> . we are unable to find policy command option in the command list.
IOS Version : c7600rsp72043-advipservicesk9-mz.122-33.SRE3.bin.
Is Linksys WRT120N still supported by cisco? I ask this because of the WPS "CRITICAL" vulnerability and no news of a patch since a month... and
*WRT120N firmware is propietary
*Not supported by DD-WRT/OPEN-WRT/FREE-WRT
Is the Cisco 850 series router supported with PoE-PowerInjector 800-PwrInj? In the 850/870 cabling guide I found a reference only 870 series would be supported.
View 2 Replies View RelatedHow many numbers of GRE Tunnels are supported on Cisco 3925 router?
View 2 Replies View RelatedThe HWIC-2CE1T1-PRI card isn't supported on a CISCO2801 router
View 7 Replies View RelatedHow many numbers of GRE Tunnels are supported on Cisco 3925 router?
View 1 Replies View RelatedRegion : Others
Model : TL-MR3420
Hardware Version : V2
Firmware Version :
ISP :
how to make the Hauwei E3276 LTE dongle work with the TL-MR3420 V2.1?I have tried to create a bin file, but no success - does any bin file I could use?I have not been able to get a positive response from the support team on when this will be supported...
How do I find the default throughput supported by the Router 3925E?I need a router that supports 400Mbps line 3900.The 3925E supports? If so, you need to upgrade or add a EHWIC? If so, what can I addto support that throughput?
View 6 Replies View RelatedI don't know how many of you read the article List of tested USB storage devices for the Linksys E4200 before buying it. Basically, what it says, is that you cannot connect your "too old" or "too new" (>2TB) HDD to this router and you have to settle with an WD MyBook Mirror Edition 2TB or Seagate FreeAgent Desk 2TB at best. Needless to say that this not good enough. First I believed that the list is incomplete and if a brand is listed with a model then a bigger or a smaller one will work as well. Sadly this is not the case: neither WD Passport with 320 GB (FAT32) nor a LACIE 1TB (NTFS) could be connected to E4200.
If any of you succeeded to pair the router with a different external HDD than the ones from the.
P.S.: I strongly believe that Cisco should work on an updated firmware which should expand the list of supported HDDs.
Region : Denmark
Model : TL-MR3040
Hardware Version : V1
Firmware Version : 3.14.2 Build 120822 Rel.40902n
ISP : Telia
HUAWEI LTE USB Rotator E3276 not supported?